Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Influence of porous aluminosilicate grain size materials in experimental and modelling Cs + adsorption kinetics and wastewater column process

This paper focuses on the influence of the grain size of a geopolymer based adsorbent on its Cs + adsorption performances both in batch and fixed-bed process. The geopolymer phase was used as a binder to support NaY zeolite particle in a 20 wt% charged porous composite with 160 m 2 .g –1 of porous surface area. These samples were shaped with three grain sizes (50 /100/500 µm) to remove 80–90 mg/g of Cs + in batch and column operations. After their microstructural and porous characterizations, their efficiency and adsorption characteristics were investigated through adsorption isotherms and kinetic in the two processes. While the grain size has no influence on the maximal extraction capacity of the adsorbent, it strongly affects the sorption kinetic. By coupling experimental data and a modelling approach, the complex sorption mechanism was highlighted, suggesting a new insight of the contaminant sorption kinetic. Then, comparison of batch and column adsorption experiments illustrates the detailed explanation of various process parameters for column study. The results show challenges for fixed-bed column utilization by the choice of the appropriate grain size as a compromise between the material sorption kinetic and hydrodynamic considerations. Furthermore, this is of high importance to more accurately optimize the design of column adsorption to assess the transport of Cs+ in multi-porous tailored grain size materials.

36 MATERIALS SCIENCE↗

X-ray studies of dynamic aging in an aluminum alloy subjected to severe plastic deformation

In this work, X-ray scattering methods were applied for a quantitative characterization of the microstructure of an aluminum alloy of the Al–Mg–Si system during dynamic aging realized through the high pressure torsion technique. A qualitative and quantitative phase analysis of the alloy was performed, together with Al alloy lattice parameter determination. From the reflections broadening the effective size of the coherent scattering domains and the lattice microstrain were determined in the framework of the Halder–Wagner approach. Using the method of small-angle X-ray scattering, the quantitative characteristics of the size, shape and spatial distribution of the secondary phase particles formed in the Al alloy during dynamic aging were established. In order to validate the obtained results, the method of small-angle X-ray scattering was preliminarily tested on similar samples after artificial aging and compared with the results from small-angle neutron diffraction widely known in literature. - Highlights: • Spherical fcc β-Mg2Si precipitates formed in Al 6201 alloy during dynamic aging in the course of severe plastic deformation. • The size, shape and distribution of the precipitates due to artificial and dynamic aging were revealed by SAXS method. • Monoclinic needle-like β' precipitates and Al5FeSi intermetallic phase were detected in 6201 alloy after T6 treatment.

36 MATERIALS SCIENCE↗

Structure-property relation and Weibull analysis of calcium aluminate cement pastes

Highlights: • Weibull distribution analysis was conducted for calcium aluminate cement pastes with 52 wt% and 71 wt% of alumina contents. • Compressive strength ranged from 10 to 45 MPa. • The hydrated phases found showed diverse polymorphisms of Gibbsite (Nordstrandite, Bayerite, Hidrogarnet and Gehlenite). - Abstract: In this investigation calcium aluminate cement (CAC) pastes with 52 wt% and 71 wt% of alumina contents were fabricated and characterized with different techniques. Samples were made with 0.4 and 0.5 water to cement (W/C) ratios. Both the raw cement powders and their corresponding samples after hydration were characterized in their microstructure by scanning electron microscopy, X-ray diffraction (with Rietveld refinement), X-ray fluorescence (XRF), Fourier Transform Infrared Spectroscopy (FTIR), density, and compression tests. With the compressive strength results, Weibull distribution analysis was conducted for 20 samples per composition. The higher compression strength obtained was about 45 MPa, which corresponds to samples with the higher W/C contents. The hydrated phases found showed diverse polymorphisms of Gibbsite (Nordstrandite, Bayerite, Hidrogarnet and Gehlenite).

36 MATERIALS SCIENCE↗

The evolution history of superalloy powders during hot consolidation and plastic deformation

Highlights: • Element segregations in a powder metallurgy superalloy at different states are identified. • The surface energy drives precipitation of oxides, carbides, and γ' particles on powder surface during hot consolidation. • Prior particle boundary structure is distorted and more uniformly refined grains are obtained after hot extrusion. - Abstract: Powder metallurgy superalloys are widely used to produce critical rotating parts in turbine engines. However, the issues like what is the driving force of precipitation on prior particle boundary (PPB) during consolidation and how the PPB structure evolves during plastic deformation still remain to be resolved. In this study, with the characterization of the microstructure evolution from powder, consolidation, to plastic deformation, the segregation of alloying elements on the particle boundaries at elevated temperature was analyzed by equilibrium thermodynamic calculations, and the distortion of PPB structure under large plastic deformation was quantitively simulated by finite element (FE) methods. The results indicated that surface energy serves as the main driving force of PPB precipitation and hot extrusion could distort the PPB structure and yield more uniformly refined grains.

36 MATERIALS SCIENCE↗

Influence of cyclic thermal treatments on the oxidation behavior of Ti-6Al-2Sn-4Zr-2Mo alloy

Highlights: • The oxidation kinetics of commercially titanium alloys has been extensively investigated following isothermal treatments. • Components in aerospace applications are subjected to temperature gradients which can modify the oxidation kinetics of Ti-6242. • The main goal of the present research is to study the formation of the oxide scale and the alpha case layer under cyclic thermal treatments • Results are with those achieved by isothermal treatments. - Abstract: Ti-6Al-2Sn-4Zr-2Mo is one of the most common titanium alloys for aerospace industry. This alloy experiences oxidation phenomenon at elevated temperatures. In the present study, cyclic thermal treatments were performed in air at 500, 593 and 700 °C, up to 500 cycles, in order to determine the oxidation kinetics and to analyze the oxide scale and alpha-case formation. Moreover, results were compared to those achieved under isothermal conditions to elucidate differences between both thermal conditions. In this sense, metallographic techniques and X-ray diffraction, together with a detailed advanced characterization of the microstructure by Field Emission Scanning Electron Microscopy and Focus Ions Beam, were used to analyze surface oxidation evolution. Results pointed out that cyclic treatments induced a strong increase of the weight gain compared to isothermal treatments. The analysis of the oxide scale revealed the formation of not only rutile, as isothermal treatments, but also anatase. Thickness of the oxide scale was higher for cyclic conditions, while alpha case did not exceed values reached by isothermal treatments and even became lower at 500 °C.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of friction stir welded Haynes 282

Advanced ultrasupercritical (A-USC) steam plants are designed to operate at high temperatures and pressures due to the necessity for higher operational efficiency. The extreme operating conditions of A-USC requires the deployment of precipitation strengthened Ni-base alloys that exhibit elevated temperature strength and good fabricability. Fusion welding of precipitation strengthened nickel alloys lead to solidification cracking in fusion zone and/or liquation cracking in heat affected zone. Therefore, an alternative non-melting welding technique is a necessity to efficiently join nickel alloys. In the current study, friction stir welding, a solid state joining technique was implemented on a precipitation strengthened nickel-based superalloy, Haynes 282. Detailed microstructural and mechanical properties characterization was carried out. The processed region exhibited wrought, fine-grained microstructure, absence of weld defects such as voids and cracks and absence of elemental segregation. Both hardness and cross-weld tensile tests demonstrated that the weld region was stronger than the base material. And the cross-weld tensile samples failed in the base material. Based on joint efficiency analysis, friction stir welded Haynes 282 outperformed fusion welds.

36 MATERIALS SCIENCE↗

Scalable aqueous-phase fabrication of reduced graphene oxide nanofiltration membranes by an integrated roll-to-roll (R2R) process

Economic fractionation of multicomponent biomass-derived streams is a key challenge in biobased fuels and chemicals production. Kraft black liquor (BL) is generated at ~1 billion tons/yr globally from biomass pulping and contains ~15wt% total solids including lignin, hemicellulose fragments, and inorganics. Membrane-based BL concentration is attractive but challenged by low solute rejections and poor stability in BL, which combines alkaline pH (~13), high dissolved solids content (15+ wt%) and high temperature (70–85°C). Here we discuss the scaled fabrication and characterization of reduced graphene oxide (rGO) nanofiltration membranes by slot die coating on a roll-to-roll (R2R) with integrated vacuum filtration. Here, we obtain high-quality 90×30 cm rGO membranes (referred to as “R2R-rGO membranes” in this work) with ~100 nm average thickness supported on porous poly(ethersulfone) (PES) sheets, and an effective area of 2700cm 2 . We present characterizations of their microstructure and uniformity as mapped over large areas by scanning electron microscopy (SEM), ellipsometry, adhesion test and X-ray photoelectron spectroscopy (XPS). The constructed ellipsometry model for the rGO membrane/PES substrate composite was successfully applied to 48 different locations of the R2R-rGO membranes. The R2R-rGO membranes showed >98% lignin rejection with a steady state flux of ~12 LMH at 50bar in a 15.7wt% total solids (TS) kraft BL stream at 72°C and 2–3 gal/min crossflow rates. Slot die coating on a R2R platform with integrated vacuum filtration can enable rapid fabrication of high-quality GO membranes at scale without organic solvents or volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogen influences thermal activation parameters for dislocation glide during low cycle fatigue of 316L stainless steel

Measurements of activation areas are used to investigate the effect of hydrogen on the kinetics of dislocation glide during cyclic deformation in cold-worked 316L stainless steel. Non-charged and hydrogen-precharged (H-precharged) specimens were tested in low cycle fatigue (LCF) under plastic strain control. A series of plastic strain rate changes was performed periodically at the peak true plastic strain from the first cycle to half-life, and at various plastic strain values around stable hysteresis loops near half-life to determine the operational activation area, Δ a ∗. Both material conditions demonstrate a rapid increase in Δ a ∗ during the initial rapid softening followed by a region of approximately constant values coinciding with a reduced rate of softening. Near half-life, hydrogen reduces Δ a ∗ at a given true stress due to its effect on the activation distance and obstacle spacing. The magnitudes of Δ a ∗ reveal that bypassing solutes, cutting forest dislocations, and initiating cross slip are important mechanisms of thermally activated dislocation glide at all amplitudes, except hydrogen suppresses cross slip at the lowest plastic strain amplitudes. These results are supported by electron microscopy characterization of deformed microstructures. A Haasen plot analysis indicates that forest dislocations control the kinetics of deformation in both material conditions. It also reveals the presence of athermal obstacles in both non-charged and H-precharged conditions, likely dense dislocation tangles and cell walls. Additionally, the effect of hydrogen on microstructure evolution (by reducing the propensity for cross slip) leads to a dependence of athermal stress on plastic strain amplitude.

Activation area↗

Simultaneous bright- and dark-field X-ray microscopy at X-ray free electron lasers

Abstract The structures, strain fields, and defect distributions in solid materials underlie the mechanical and physical properties across numerous applications. Many modern microstructural microscopy tools characterize crystal grains, domains and defects required to map lattice distortions or deformation, but are limited to studies of the (near) surface. Generally speaking, such tools cannot probe the structural dynamics in a way that is representative of bulk behavior. Synchrotron X-ray diffraction based imaging has long mapped the deeply embedded structural elements, and with enhanced resolution, dark field X-ray microscopy (DFXM) can now map those features with the requisite nm-resolution. However, these techniques still suffer from the required integration times due to limitations from the source and optics. This work extends DFXM to X-ray free electron lasers, showing how the $$10^{12}$$ 10 12 photons per pulse available at these sources offer structural characterization down to 100 fs resolution (orders of magnitude faster than current synchrotron images). We introduce the XFEL DFXM setup with simultaneous bright field microscopy to probe density changes within the same volume. This work presents a comprehensive guide to the multi-modal ultrafast high-resolution X-ray microscope that we constructed and tested at two XFELs, and shows initial data demonstrating two timing strategies to study associated reversible or irreversible lattice dynamics.

47 OTHER INSTRUMENTATION↗

Antisite Defects in Layered Multiferroic CuCr 0.9 In 0.1 P 2 S 6

The CuCr 1-x In x P 2 S 6 system represents a large family of metal chalcogenophosphates that are unique and promising candidates for 2D materials with functionalities such as ferroelectricity. We carried out detailed microstructural and chemical characterization of these compounds using aberration-corrected STEM, in order to understand the origin of these different ordering phenomena. Quantitative STEM-HAADF imaging and analysis identified the stacking order of an 8-layer thin flake, which leads to the identification of anti-site In 3+ (Cu + ) doping. We believe that these findings will pave the way towards understanding the ferroic coupling phenomena in van der Waals lamellar compounds, as well as the potential applications in 2-D electronics.

36 MATERIALS SCIENCE↗

Gold nanotriangles decorated with superparamagnetic iron oxide nanoparticles: a compositional and microstructural study

The combination of iron oxide and gold in a single nanoparticle results in both magnetic and plasmonic properties that can stimulate novel applications in bio-sensing, medical imaging, or therapeutics. Microwave assisted heating allows the fabrication of multi-component, multi-functional nanostructures by promoting selective heating at desired sites. Recently, we reported a microwave-assisted polyol route yielding gold nanotriangles decorated with iron oxide nanoparticles. Here, we present an in-depth microstructural and compositional characterization of the system by using scanning transmission electron microscopy (STEM) and electron energy loss (EELS) spectroscopy. A method to remove the iron oxide nanoparticles from the gold nanocrystals and some insights on crystal nucleation and growth mechanisms are also provided.

36 MATERIALS SCIENCE↗

Solidification of Au-Cu-Si alloys investigated by a combinatorial approach

Composition libraries of Au-Cu-Si films comprising 800 composition patches were fabricated through co-sputtering deposition from elemental targets. The gold composition varies between 47% (compositions are in atomic percentage) and 81%, copper between 8% and 40%, and silicon between 6% and 36% within the library. We designed and used a high-throughput optical characterization method to detect melting and solidification based on changes in the film's contrast; further microscopy characterization reveals the microstructure. This approach reveals the composition dependence of the nucleation temperature and primary phase, which allows us to draw conclusions about glass forming ability and to identify bulk metallic glass forming compositions. Our solidification results suggest that the best glass forming composition coincides with the composition at which a transition from one primary phase to another occurs. We show that in general this transition is not at the eutectic composition but at the lowest nucleation temperature.

36 MATERIALS SCIENCE↗

On the Effect of Ramp Rate in Damage Accumulation of the CPV Die-Attach: Preprint

It is commonly understood that thermal cycling at high temperature ramp rates may activate unrepresentative failure mechanisms. Increasing the temperature ramp rate of thermal cycling, however, could dramatically reduce the test time required to achieve an equivalent amount of thermal fatigue damage, thereby reducing overall test time. Therefore, the effect of temperature ramp rate on physicaldamage in the CPV die-attach is investigated. Finite Element Model (FEM) simulations of thermal fatigue and thermal cycling experiments are made to determine if the amount of damage calculated results in a corresponding amount of physical damage measured to the die-attach for a variety of fast temperature ramp rates. Preliminary experimental results are in good agreement with simulations andreinforce the potential of increasing temperature ramp rates. Characterization of the microstructure and resulting fatigue crack in the die-attach suggest a similar failure mechanism across all ramp rates tested.

14 SOLAR ENERGY↗

Simultaneous three-dimensional elemental mapping of Hollandite and Pyrochlore material phases in ceramic waste form materials

In this study, differential X-ray absorption contrast tomography was performed on model ceramic composite systems to image the 3D spatial distributions of Ga and Nd containing phases. The model material systems were fabricated such that they contained two constituent phases. Ga–doped Ba hollandite (Ba 1.33 Ga 2.66 Ti 5.34 O 16 ), and pyrochlore (Nd 2 Ti 2 O 7 ) which are under consideration as nuclear waste immobilization matrices. Two complementary techniques have been used to characterize the 3D distribution of phases. The analysis suggests that the 3D spatial distributions of hollandite and pyrochlore can be readily identified through the distributions Ga and Nd, respectively. These results represent a critical development towards characterizing the complex microstructure inherent to practical materials such as multiphase ceramic composite waste forms. Furthermore, these methods can be applied to elucidate microstructural features that fundamentally determine the performance and properties of complex systems, which is central to the design of durable waste forms as well as many other real materials such fuel cells, batteries, ultra-high temperature ceramics.

36 MATERIALS SCIENCE↗

Novel Steels for High Temperature Carburizing (Final Scientific Report)

This program was undertaken to develop a microalloy-modified grade of standard carburizing steel that can successfully exploit the high temperature carburizing capabilities of current commercial low pressure (i.e. 'vacuum') carburizing systems. Such steels can lower the amount of energy required for commercial carburizing operations by reducing the time required for deep-case carburizing operations. The specific technical objective of the work was to demonstrate a carburizing steel composition capable of maintaining a prior austenite grain size no larger than ASTM grain size number 5 after exposure to simulated carburizing conditions of 1050°C for 8 hr. Such thermal exposure should be adequate for producing carburized case depths up to about 2 mm. Such carburizing steels are expected to be attractive for use across a wide range of industries, including the petroleum, chemical, forest products, automotive, mining and industrial equipment industries. They have potential for reducing energy usage during low pressure carburizing by more than 25%, as well as reducing cycle times and process costs substantially. They also have potential for reducing greenhouse gas emissions from existing low pressure carburizing furnaces by more than 25%. High temperature carburizing can be done in most modern low pressure carburizing systems with no additional capital investment. Accordingly, implementing this technology on carburizing furnaces will provide a return on investment significantly greater than 10%. If disseminated throughout the domestic carburizing community, the technology has potential for saving on the order of 23 to 34 trillion BTU/year in industrial energy usage. Under the program, two compositions of microalloyed, coarsening-resistant low alloy carburizing steels were developed, produced and evaluated. After vacuum annealing at 1050°C for 8 hrs and high pressure gas quenching, both steels exhibited a prior austenite ASTM grain size number of 5.0 or finer. For comparison, a control alloy of similar composition but without the microalloy additions exhibited a duplex prior austenite grain size with grains ranging from ASTM grain size 3 down to ASTM grain size 1 after similar processing and thermal exposure. These results confirm the potential for using microalloy additions of Ti, B, Nb, Al, rare earths and/or N for austenite grain size control in Cr-Mo (i.e. 4000-series) low alloy carburizing steels. They also demonstrate that these microalloy additions will not compromise the processability of the steel; all three materials produced under the program could be hot worked readily using normal steel processing protocols. To fully realize the technical and commercial potential of these steels, there is a need to continue development work using larger-scale heats. These larger-scale heats are needed to provide adequate material for fatigue testing of quenched and tempered alloys, to conduct more complete investigations of potential alloy chemistries and to provide additional material for processing studies. It will also be beneficial to carefully review intellectual property issues associated with this family of steels, since existing Japanese patent literature suggests that significant microstructural and/or process characterization work may be needed on new materials to confirm that these materials fall outside existing patent claims.

02 PETROLEUM↗

Computational Design of Creep-Resistant Alloys and Experimental Validation in Ferritic Superalloys

A new class of ferritic superalloys containing B2-type zones inside parent L21-type precipitates in a disordered solid-solution matrix, also known as a hierarchical-precipitate strengthened ferritic alloy (HPSFA), has been developed for high-temperature structural applications in fossil-energy power plants. These alloys were designed by the addition of the Ti element into a previously-studied NiAl-strengthened ferritic alloy (denoted as FBB8 in this study). In the present research, systematic investigations, including advanced experimental techniques, first-principles calculations, and numerical simulations, have been integrated and conducted to characterize the complex microstructures and excellent creep resistance of HPSFAs. The experimental techniques include transmission-electron microscopy, scanningtransmission- electron microscopy, neutron diffraction, and atom-probe tomography, which provide detailed microstructural information of HPSFAs. Systematic tension/compression creep tests revealed that HPSFAs exhibit the superior creep resistance, compared with the FBB8 and conventional ferritic steels (i.e., the creep rates of HPSFAs are about 4 orders of magnitude slower than the FBB8 and conventional ferritic steels.) First-principles calculations include interfacial free energies, anti-phase boundary (APB) free energies, elastic constants, and impurity diffusivities in Fe. Combined with kinetic Monte- Carlo simulations of interdiffusion coefficients, and the integration of computational thermodynamics and kinetics, these calculations provide great understanding of thermodynamic and mechanical properties of HPSFAs. In addition to the systematic experimental approach and first-principles calculations, a series of numerical tools and algorithms, which assist in the optimization of creep properties of ferritic superalloys, are utilized and developed. These numerical simulation results are compared with the available experimental data and previous first-principles calculations, providing deep insight of creep mechanisms of the creep-resistant ferritic superalloys. With the above investigations, the HPSFA has been proved with superior creep resistance, and its microstructure, creep mechanism, and thermal/mechanical properties have been well studied and understood. In the future, HPSFAs with different additions and sizes of precipitates will be investigated and developed to further enhance the creep resistance of the ferritic superalloys and provide promising applications of the fossil-energy power plants.

Liaw, Peter↗

Comparison of electron beam and laser beam powder bed fusion additive manufacturing process for high temperature turbine component materials

The evolving 3D printer technology is now at the point where some turbine components could be additive manufactured (AM) for both development and production purposes. However, this will require a significant evaluation program to qualify the process and components to meet current design and quality standards. The goal of the project was to begin characterization of the microstructure and mechanical properties of Nickel Alloy X (Ni-22Cr-18Fe-9Mo) test bars fabricated by powder bed fusion (PBF) AM processes that use either an electron beam (EB) or laser beam (LB) power source. The AM materials produced with the EB and LB processes displayed significant differences in microstructure and resultant mechanical properties. Accordingly, during the design analysis of AM turbine components, the specific mechanical behavior of the material produced with the selected AM process should be considered. Comparison of the mechanical properties of both the EB and LB materials to those of conventionally processed Nickel Alloy X materials indicates the subject AM materials are viable alternatives for manufacture of some turbine components.

36 MATERIALS SCIENCE↗

Advanced low-cost intermetallic coatings for molten salt pump impeller. Final report

1.0 INTRODUCTION The use of solar energy to produce steam for the generation of electricity is an established technology, with multiple designs for concentrating solar power (CSP) steam generators available commercially and a number of such units currently operating. As part of the effort to improve the overall efficiency of this technology, designers have developed thermal energy storage (TES) mechanisms that employ molten salt to capture a portion of the solar energy available during the day-time hours and make that energy available for steam generation during periods when the sun’s energy is not available. In current TES systems, nitrate salts are used extensively as the medium of energy exchange. However, due to the chemical instability of these salts at temperatures above 600ºC, they are not being considered for use in the next more efficient generation of CSP plants, in which the energy exchange fluids will be required to operate in the range 600ºC to 800ºC. At these higher temperatures, molten chloride salts, such as KCl-MgCl2, are viewed as promising alternatives to the nitrate salts, but, of course, these chloride-based salts are highly corrosive to the engineering alloys commonly used in the construction of pressure vessels, heat exchangers, pumps and piping at high temperatures. Hence, a solution to the problem of material degradation is essential if the next generation of CSP plants is to be commercially viable (Ref 1). In order to effectively address the problem of molten chloride salt corrosion at high temperatures (≥ 750ºC) and thereby to reduce the cost of molten salt tanks and related apparatus, various options have been considered, with one of the most promising being an innovative coatings system developed and applied onto low alloy ferritic or austenitic stainless material. Development of such a coating system would reduce the capital costs of thermal energy storage (TES) and increase the overall efficiency of the concentrating solar power (CSP) system. Although high strength nickel base alloys are well suited for many high temperature applications, they have significant limitations when exposed to molten chloride salt conditions and they are very expensive. Monolithic materials such as the austenitic stainless steels (e.g., SS310 and SS347) and the more common nickel base alloys (e.g., IN625 and IN800H) have exhibited high corrosion rates in molten chloride salt environments (Ref1). Molten salt corrosion of IN625 in salts containing chlorides showed a catastrophic corrosion rate of 1.111”/year at 800ºC (Ref1). Hence, an innovative coatings solution to mitigate molten chloride salt corrosion is needed. Of the many coating techniques available in the market, no one technique appears to be capable of producing effective protection from molten salt corrosion at a relatively low cost. There are thermal spray coating techniques, in particular the twin wire-arc technology, that are attractive when considering the coating of large molten salt tanks because the coatings application rate is high, the overall application cost is low and repairs to the coating can readily be made either in the shop or in the field. However, the twin wire arc coating materials currently available in the market have certain inherent limitations, including porosity and mechanical bonding to the substrate, which limit their effectiveness in providing protection against molten chloride salt corrosion at high temperatures. What is required is an approach that combines the economy and versatility of thermal spray wire-arc technology with the superior resistance of advanced alloys to effectively combat molten chloride salt corrosion at elevated temperatures. Applied Thermal Coatings, Inc. (ATC) has investigated an innovative coatings technology to produce dual layer cermet/ceramic coatings that will be dense and impervious to any corrosive molten salts/fluids, thereby resisting the effects of molten salt corrosion. Development of coatings using this technology will make it possible to fabricate the molten salt systems using a relatively low-cost base material, which will reduce the overall cost of the power generating system and enhance the commercial viability of solar power. 2.0 PROJECT OVERVIEW Of the coating technologies available for the production of a cost-effective method of protection from the effects of high-temperature chloride attack, there are two that offer specific advantages for the CSP/TES application, particularly when used in a way that effectively complements the strengths of each coating method. The first of these is electroless nickel plating, through which a nickel-rich layer is produced on the surface of a component through chemical reduction. The second coating technology is aluminizing, in which aluminum is diffused into the surface of a component and, depending on the composition of the substrate, aluminides are formed. The objective of this project has been to demonstrate the feasibility of a low- cost coating for the protection of pump impellers used for the inductive transport of molten salts. Initial interest focused on an inter-metallic nickel aluminide coating and subsequently, for economic reasons, consideration also was given to a coating composed of iron aluminides. Applying such coatings to low alloy or austenitic stainless-steel substrates will provide the superior resistance to molten chloride salt corrosion and blade tip erosion that normally can be achieved only through the use of more highly alloyed – and, therefore, more expensive - nickel-base materials and it will do so at a substantially lower cost. The coating systems evaluated were designed to take advantage either of the combined strengths of the electroless nickel plating process and the aluminizing process to produce a nickel-aluminide intermetallic coating or to rely solely on the aluminizing process to produce, in conjunction with iron from the substrate, a protective layer consisting of iron aluminides. With respect to the nickel aluminide protection, this has been achieved by first depositing a layer of nickel-rich alloy onto an austenitic stainless substrate using the electroless nickel plating process and then aluminizing the nickel- coated surface to produce the nickel aluminide coating. With respect to the iron aluminide protection, this has been achieved by aluminizing bare austenitic stainless steel. Testing has supported the conclusion that the developed coatings will resist attack by molten chloride salts at high temperatures (550°C to 750°C) and have sufficient hardness to resist blade tip erosion.The steps taken to develop either a low-cost intermetallic nickel aluminide coating using electroless nickel plating and aluminizing or a low-cost iron aluminide coating using aluminizing only, and to demonstrate the quality of the coatings and their effectiveness against molten chloride salt corrosion and erosion at high temperatures (≤ 750ºC) have been as follows: 1. Design of the optimum electroless nickel plating and aluminizing mixtures using advanced thermodynamic analysis; 2. Development of processing parameters for the electroless nickel plating and aluminizing processes, to be used either together or separately; 3. Production of specimens coated using the designated electroless nickel plating process; 4. Production of samples with intermetallic nickel aluminide coating or iron aluminide coating; 5. Investigation of the performance of the intermetallic nickel aluminide coating and the iron aluminide coating when subjected to molten chloride salts corrosion at high temperatures (≥ 750ºC); and, 6. Metallurgical characterization of the microstructure of the coatings, both prior to and after exposure to molten salt environments at elevated temperatures.

14 SOLAR ENERGY↗