Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Neutron Assay System for Confinement Vessel Disposition

Waste will be removed from confinement vessels remaining from 1970s-era experiments. Los Alamos has 9+ spherical confinement vessels remaining from experiments. Each vessel contains {approx} 500 lbs of radioactive debris such as actinide metals and oxides, metals, powdered silica, graphite, and wires and hardware. In order to dispose of the vessels, debris and contamination must be removed. Neutron assay system was designed to assay vessels before and after cleanout. System requirements are: (1) Modular and moveable; (2) Capable of detecting {approx}100g {sup 239}Pu equivalent in a 2-inch thick steel sphere with 6 foot diameter; and (3) Capable of safeguards-quality assays. Initial design parameters arethe use of 4-atm {sup 3}He tubes with length of 6 feet, and {sup 3}He tubes embedded in polyethelene for moderation. This paper describes the calibration of the Confinement Vessel Assay System (CVAS) and quantification of its uncertainties. Assay uncertainty depends on five factors: (1) Statistical uncertainty in the assay measurement; (2) Statistical uncertainty in the background measurement; (3) Statistical uncertainty in the isotopics determination - This should be much smaller than the other uncertainties; (4) Systematic uncertainty due to position bias; and (5) Systematic uncertainty due to fluctuations in cosmic ray spallation. This one can be virtually eliminated by performing the background measurement with an empty vessel - but that may not be possible. We used modeling and experiments to quantify the systematic uncertainties. The calibration assumes a uniform distribution of material, but reality will be different. MCNPX modeling was used to quantify the positional bias. The model was benchmarked to build confidence in its results. Material at top of vessel is 44% greater than amount assayed, according to singles. Material near 19-tube detector is 38% less than amount assayed, according to singles. Cosmic ray spallation contributes significantly to the background. Comparing rates with and without a vessel showed that spallation adds an average of 27.27 singles/s and 5.45 doubles/s to background. Errors in the background rates were estimated at 20%.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The role of ozone in the formation and structural evolution of graphene oxide obtained from nanographite

Chemical exfoliation of graphite under strong oxidizing conditions yields graphene oxide nanosheets with oxy functional groups on the carbon basal plane. The importance of ozone in the chemical oxidation mechanism of graphite by the widely-used Hummers' method has been largely overlooked. Herein we demonstrate that the ozonolysis of graphite leads to the formation of secondary epoxy and perox-ymonosulfate ester functional groups arising from a rotationally hindered Criegee intermediate and sulfuric acid, in a strongly favored thermodynamic process. This mechanistic step is followed by formation of adjacent epoxy and hydroxy groups as major functionalities on graphene oxides via a radical process, and leaves a significant amount of unreacted peroxides well above levels previously recognized. The thermal decomposition of graphene releases sulfur oxygen species (SO 2 and SO), but does not appear to release ozone even if this reaction pathway is moderately favored thermodynamically. Here we propose anew structural model for graphene oxide based on detailed chemical and spectroscopic data that provides insight into observed chemical reactivity and physical properties, including the antimicrobial activity and protein deactivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New Materials for Electric Drive Vehicles - Final CRADA Report

This project was sponsored by the US DOE Global Initiatives for Proliferation Prevention. The object was for Ukrainian and US partners, including Argonne, AETC, and Dontech to develop special carbon materials and factory production equipment with the goal of making better car batteries to achieve DOE's goals for all-electric and plug-in hybrid electric vehicles. Carbon materials are used in designs for lithium-ion batteries and metal-air batteries, both leading contenders for future electric cars. Specifically, the collaborators planned to use the equipment derived from this project to develop a rechargeable battery system that will use the carbon materials produced by the innovative factory process equipment. The final outcome of the project was that the Ukrainian participants consisting of the Kharkov Institute of Physics and Technology (KIPT), the Institute of Gas of National Academy of Sciences of Ukraine and the Materials Research Center, Ltd. designed, built, tested and delivered 14 pieces of processing equipment for pilot scale carbon production lines at the AETC, Arlington Heights facilities. The pilot scale equipment will be used to process materials such as activated carbon, thermally expanded graphite and carbon coated nano-particles. The equipment was shipped from Ukraine to the United States and received by AETC on December 3, 2013. The equipment is on loan from Argonne, control # 6140. Plug-in hybrid electric vehicles (PHEV) and all-electric vehicles have already demostrated success in the U.S. as they begin to share the market with older hybrid electric designs. When the project was conceived, PHEV battery systems provided a ~40 mile driving range (2011 figures). DOE R&D targets increased this to >100 miles at reduced cost less than $250/kWh (2011 figures.) A 2016 Tesla model S has boasted 270 miles. The project object was to develop pilot-production line equipment for advanced hybrid battery system that achieves cycle life of 1000, an energy density of 280 Wh/kg and specific density of 600Wh/l. This project delivers factory equipment to produce these advanced battery materials.

36 MATERIALS SCIENCE↗

Predicting viscoelastic response and delayed failures in general laminated composites

Although graphite fibers behave in an essentially elastic manner, the polymeric matrix of graphite/epoxy composites is a viscoelastic material which exhibits creep and delayed failures. The creep process is quite slow at room temperature, but may be accelerated by higher temperatures, moisture absorption, and other factors. Techniques are being studied to predict long-term behavior of general laminates based on short-term observations of the unidirectional material at elevated temperatures. A preliminary numerical procedure based on lamination theory is developed for predicting creep and delayed failures in laminated composites. A modification of the Findley nonlinear power law is used to model the constitutive behavior of a lamina. An adaptation of the Tsai-Hill failure criterion is used to predict the time-dependent strength of a lamina. Predicted creep and delayed failure results are compared with typical experimental data.

Dillard, D. A.↗

Nonlinear response of resin matrix laminates using endochronic theory

The nonlinear response of laminated, resin matrix fibrous composites is modeled using orthotropic endochronic theory. The theory is formulated in terms of elastic constants and endochronic parameters characterizing the linear and nonlinear response, respectively, of unidirectional composites. All constants and parameters can be determined from normal (tension and/or compression) and shear tests on unidirectional and off-axis specimens. The nonlinear constitutive response relations for the unidirectional lamina are presented and the procedure for determining constants and parameters from test is described. The results are then used to predict the nonlinear response of unidirectional laminae and angle-ply laminates. Comparison between theory and experiment for compression loading of AS4/3502 graphite-epoxy, angle-ply laminates shows excellent correlation.

Mathison, S. R.↗

Antimicrobial mechanisms of g‐C 3 N 4 @ ZnO against oomycetes Phytophthora capsici: from its metabolism, membrane structures and growth

Abstract BACKGROUND Phytophthora capsici , a refractory and model oomycete plant pathogen, especially threatens multiple vegetable crops. A limited number of chemical pesticides play a vital role in controlling oomycete plant diseases. However, this approach often leads to excessive use of chemical agent, exacerbates environmental issues and more and more drug‐resistant strains of oomycete. Therefore, it is imperative to devise innovative solutions that can effectively address the infection of oomycete while maintaining high levels of environmental sustainability and low toxicity. RESULTS In this study, g‐C 3 N 4 @ZnO heterostructure was synthesized and characterized. The g‐C 3 N 4 @ZnO showed higher toxicity on Phytophthora capsici than graphitic carbon nitride (g‐C 3 N 4 ) nanosheets and zinc oxide (ZnO) nanoparticles in vitro and in vivo . Except the hyphal growth of Phytophthora capsici , their germination rate of spores, sporangium formation and number of spores were all suppressed by g‐C 3 N 4 @ZnO heterostructure. Furthermore, we found that this g‐C 3 N 4 @ZnO heterostructure has higher photocatalytic activity under visible light, which potentially enhanced the reactive oxygen species (ROS) mediated stress on Phytophthora capsici . Ultrastructural morphology, global changes of gene expression and weighted gene co‐expression network analysis all supported that the anti‐oomycete activity of g‐C 3 N 4 @ZnO was manifested in the destruction of membrane system and inhibition of multiple metabolisms of Phytophthora capsici under visible irradiation, which also could be attributed to the ROS and zinc ion (Zn 2+ ) mediated stress. CONCLUSION This works offers a novel oomycete disease management strategy by using g‐C 3 N 4 @ZnO, which were attributed to the ROS stress, destruction of membrane system and inhibition of multiple metabolisms. © 2023 Society of Chemical Industry.

Cai, Lin↗

Analysis of electrolyte imbibition through lithium-ion battery electrodes

A quantitative measurement of wettability between the porous electrode and the electrolyte in lithium-ion batteries can greatly improve our understanding of wetting behavior. Although the wetting balance method is widely used to measure the electrolyte transport rate in the porous electrodes, it suffers from several drawbacks and has limited accuracy. We here presented a combined experimental and theoretical investigation of the dynamics of electrolyte imbibition through electrodes. We suggested a novel method to accurately measure the electrolyte imbibition rate. Excellent agreement between the experimental data and the developed analytical model is obtained. The coefficient of penetrance (COP) and the solid permeability coefficient (SPC) are identified as important parameters, i.e., the electrolyte with higher COP value wets faster into an electrode, whereas for an electrolyte, the electrode with higher SPC value is more amenable to be impregnated. The effect of electrolyte salt concentration and electrolyte solvent has been studied in detail. The result implies that increasing salt concentration adversely influences electrolyte wetting rate, whereas switching from EC-DEC system to EC-EMC system improves electrolyte wetting rate. Moreover, for the electrolytes tested in this study, the imbibition into the uncalendered graphite anode is much faster than that into the uncalendered NMC532 cathode.

25 ENERGY STORAGE↗

Control of the Plasma-Material Interface for Long Pulse Optimization in the Experimental Advanced Superconducting Tokamak (EAST) (Final Report)

This project involved a collaborative effort, led by Dr. Rajesh Maingi of Princeton Plasma Physics Laboratory, to understand and control the plasma-material interface to improve long pulse discharge control and performance in the EAST devices. The focus is on long pulse recycling control and optimization, which can be challenging because of their broad range of materials used for plasma-facing components (PFC) and wall conditioning techniques. The purpose of the EAST device is to demonstrate long-pulse, stable, high performance plasma operation, providing a test-bed for key physics and technology issues for next step devices. As part of these tests, EAST has deployed carbon for the lower divertor PFC, tungsten for the upper divertor, and molybdenum for the main wall. In addition wall coatings are deployed for long pulse recycling control: lithium (Li) via several delivery tools, boronization, and recently also siliconization; for example, in 2013, a layer of SiC was deposited on all of the graphite tiles. Oxygen is also present at trace levels, making for a complex mix of materials and plasma-materials interactions (PMI). This mix of materials and the limited durability of wall coatings, coupled to partially optimized cryo-pumping, lead to evolution of the recycling off the PFCs, which restricts the duration of stationary, high performance, long pulse discharges. Comparing the wall conditioning techniques, Li enables the highest energy confinement and lowest recycling for the longest duration, while also suppressing ELMs in certain discharges. More specifically, research activities at the University of Tennessee focused on heat flux profile measurements in EAST, modeling the surface response, including the bonding energetics and chemical interactions between Li with carbon, tungsten, hydrogen and impurities, in addition to post situ experimental characterization and analysis of the divertor plasma facing components in EAST. This final report describes the overall progress within each of these tasks at the University of Tennessee within the project.

36 MATERIALS SCIENCE↗

Water vapor oxidation behaviors of nuclear graphite IG-110 for a postulated accident scenario in high temperature gas-cooled reactors

Water leakage in accidental conditions of high temperature gas-cooled reactors is one of the most critical problems that can compromise the integrity of different nuclear components. In this study, oxidation behaviors of nuclear graphite IG-110 in water ingress accidental conditions were investigated. Mass loss and oxidation rates were evaluated after oxidation tests at temperatures up to 1400 °C in an Ar-20 vol% H 2 O mixed atmosphere. The activation energy decreased from 318.6 to 148.9 kJ/mol with temperature, indicating two different oxidation regimes. The cross-sections of the oxidized samples were systematically characterized. The corresponding logarithmic porosity profiles showed a temperature dependency. Pore formation moved toward near-surface regions with increasing temperature and preferential binder oxidation, with filler particle degradation. Furthermore, oxidant concentration profiles and oxidation depths were estimated using a theoretical model and compared with the experimental results. This work provides important benchmark data and safety analysis guidance for the accident scenario in high temperature gas-cooled reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Optical Fier Based System for Multiple Thermophysical Properties for Glove Box, Hot Cell and In-Pile Application

Thermal diffusivity of materials is of interest in nuclear applications at temperatures in excess of 2000°C. Commercial laser flash apparatus (LFA) that heats samples with a furnace typically do not reach these elevated temperatures nor are they easily adapted to a glove-box or hot cell environment. In this research, we performed work on an experimental technique using single laser surface heating, i.e. heating the disk sample only at its front surface with the continuous wave (CW) laser, to allow measurement of thermal diffusivity at very high temperatures within a small chamber. Thermal diffusivity is measured using a separate pulsed laser on the front side and IR detector on the rear side. The new way of heating provides easy operation in comparison to other heating methods. The measurement of sample reference temperature is needed for the measured thermal diffusivity. A theoretical model was developed to describe transient heat transfer across the sample due to the laser pulse, starting from the steady state temperature of the sample heated by the CW laser. The experimental setup was established with a 500W CW laser and maximum 50 Joule pulse laser irradiated at the front surface of the sample. The induced temperature rise at the rear surface, along with the steady-state temperature at the front surface, was recorded for the determination of thermal diffusivity and the sample temperature. Three samples were tested in vacuum over a wide temperature range of 500°C to 2100°C, including graphite, Inconel 600 and tungsten. The latter two samples were coated with sprayed graphite on their front surfaces in order to achieve surface absorption/emission needs, i.e. high absorptivity of the front surface against relatively low emissivity of the rear surface. Thermal diffusivity of graphite determined by our system are within a 5% difference of the commercial LFA data at temperatures below 1300°C and agree well with its trend at higher temperatures. Good agreement would also exist for Inconel 600 and tungsten. Despite large uncertainty of measuringthe sample temperature, the uncertainties of thermal diffusivity are less than 6% for all samples at elevated temperatures. The results indicate that single laser surface heating could be convenient and practical for the application of the LFA measurements without extra uncertainty, as temperature dependence of thermal diffusivity is usually negligible in the sample. Moreover, it is concluded that unequal surface treatment, i.e., high absorption on the front side and low emission on the rear side, greatly improves the measurement in serval aspects: less power requirement of the CW laser, less uncertainty of measured thermal diffusivity, and more uniform temperature distribution in the sample. The result of this research can be used as a general guideline for the design of this type of measurement system for nuclear applications. It can also be used directly to design and build a system similar to the one implemented in this project.

36 MATERIALS SCIENCE↗

Fatigue and Damage Tolerance Analysis of a Hybrid Composite Tapered Flexbeam

The behavior of nonlinear tapered composite flexbeams under combined axial tension and cyclic bending loading was studied using coupon test specimens and finite element (FE) analyses. The flexbeams used a hybrid material system of graphite/epoxy and glass/epoxy and had internal dropped plies, dropped in an overlapping stepwise pattern. Two material configurations, differing only in the use of glass or graphite plies in the continuous plies near the midplane, were studied. Test specimens were cut from a full-size helicopter tail-rotor flexbeam and were tested in a hydraulic load frame under combined constant axialtension load and transverse cyclic bending loads. The first determination damage observed in the specimens occurred at the area around the tip of the outermost ply-drop group in the tapered region of the flexbeam, near the thick end. Delaminations grew slowly and stably, toward the thick end of the flexbeam, at the interfaces above and below the dropped-ply region. A 2D finite element model of the flexbeam was developed. The model was analyzed using a geometrically non-linear analysis with both the ANSYS and ABAQUS FE codes. The global responses of each analysis agreed well with the test results. The ANSYS model was used to calculate strain energy release rates (G) for delaminations initiating at two different ply-ending locations. The results showed that delaminations were more inclined to grow at the locations where they were observed in the test specimens. Both ANSYS and ABAQUS were used to calculate G values associated with delamination initiating at the observed location but growing in different interfaces, either above or below the ply-ending group toward the thick end, or toward the thin end from the tip of the resin pocket. The different analysis codes generated the same trends and comparable peak values, within 5-11 % for each delamination path. Both codes showed that delamination toward the thick region was largely mode II, and toward the thin region was predominantly mode I. The calculated peak G-values from either analysis predict delamination is most likely to occur along the same interface where it was observed in the test specimens. Calculated peak G values were used with material characterization data to calculate a curve relating the fatigue life of the specimens, N, to the applied transverse load, V, for a given constant axial load.

Murri, Gretchen B.↗

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Frieman, Jason D.↗

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Frieman, Jason D.↗

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Jason David Frieman↗

Enhancing VHTR Passive Safety and Economy with Thermal Radiation Based Direct Reactor Auxiliary Cooling System

One of the most important requirements for Gen. IV Very High Temperature Reactor (VHTR) is passive safety. Currently all the gas cooled version of VHTR designs use Reactor Vessel Auxiliary Cooling System (RVACS) for passive decay heat removal. The decay heat first is transferred to the core barrel by conduction and radiation, and then to the reactor vessel by thermal radiation and convection; finally the decay heat is transferred to natural circulated air or water systems. RVACS can be characterized as a surface based decay heat removal system. The RVACS is especially suitable for smaller power reactors since small systems have relatively larger surface area to volume ratio. However, RVACS limits the maximum achievable power level for modular VHTRs due to the mismatch between the reactor power (proportional to volume) and decay heat removal capability (proportional to surface area). When the relative decay heat removal capability decreases, the peak fuel temperature increases, even close to the design limit. Annular core designs with inner graphite reflector can mitigate this effect; therefore can further increase the reactor power. Another way to increase the reactor power is to increase power density. However, the reactor power is also limited by the decay heat removal capability. Besides the safety considerations, VHTRs also need to be economical in order to compete with other reactor concepts and other types of energy sources. The limit of decay heat removal capability set by using RVACS has affected the economy of VHTRs. A potential alternative solution is to use a volume-based passive decay heat removal system, called Direct Reactor Auxiliary Cooling Systems (DRACS), to remove or mitigate the limitation on decay heat removal capability. DRACS composes of natural circulation loops with two sets of heat exchangers, one on the reactor side and another on the environment side. For the reactor side, cooling pipes will be inserted into holes made in the outer or inner graphite reflector blocks. There will be gaps between these cooling pipes and their corresponding surrounding graphite surfaces. Graphite has an excellent heat conduction property. By taking advantage of this feature, we can have a volume-based method to remove decay heat. The scalability can be achieved, if needed, by employing more rows of cooling pipes to accommodate higher decay heat rates. Since heat can easily conduct through the graphite regions between the holes made for the cooling pipes, those cooling pipes located further away from the active core region can still be very effective in removing decay heat. By removing the limit on the decay heat removal capability due to the limited available surface area as in a RVACS, the reactor power and power density can be significantly increased, without losing the passive heat removal feature. This paper will introduce the concept of using DRACS to enhance VHTR passive safety and economics. Three design options will be discussed, depending on the cooling pipe locations. Analysis results from a lumped volume based model and CFD simulations will be presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A tale of three galaxies: Deciphering THE infrared emission of the spectroscopically anomalous galaxies IRAS F10398+1455, IRAS F21013–0739, and SDSS J0808+3948

The Spitzer/Infrared Spectrograph spectra of three spectroscopically anomalous galaxies (IRAS F10398+1455, IRAS F21013–0739, and SDSS J0808+3948) are modeled in terms of a mixture of warm and cold silicate dust, and warm and cold carbon dust. Their unique infrared (IR) emission spectra are characterized by a steep ∼5–8 μm emission continuum, strong emission bands from polycyclic aromatic hydrocarbon (PAH) molecules, and prominent silicate emission. The steep ∼5–8 μm emission continuum and strong PAH emission features suggest the dominance of starbursts, while the silicate emission is indicative of significant heating from active galactic nuclei (AGNs). With warm and cold silicate dust of various compositions (“astronomical silicate,” amorphous olivine, or amorphous pyroxene) combined with warm and cold carbon dust (amorphous carbon, or graphite), we are able to closely reproduce the observed IR emission of these galaxies. We find that the dust temperature is the primary cause in regulating the steep ∼5–8 μm continuum and silicate emission, insensitive to the exact silicate or carbon dust mineralogy and grain size a as long as a≲1 μm. More specifically, the temperature of the ∼5–8 μm continuum emitter (which is essentially carbon dust) of these galaxies is ∼250–400 K, much lower than that of typical quasars, which is ∼640 K. Moreover, it appears that larger dust grains are preferred in quasars. The lower dust temperature and smaller grain sizes inferred for these three galaxies compared with that of quasars could be due to the fact that they may harbor a young/weak AGNs that is not maturely developed yet.

79 ASTRONOMY AND ASTROPHYSICS↗

Macrosegregation and Grain Formation Caused by Convection Associated with Directional Solidification Through Cross-Section Increase

Cylindrical Al-7 wt% Silicon, Al-19 wt% Copper and Lead-6 wt% Antimony alloy samples were directionally solidified (DS) with liquid above, solid below, and gravity pointing down, in graphite crucibles having an abrupt cross-sectional increase. These alloys have similar solidification shrinkage but are expected to have different degrees of thermosolutal convection during solidification. Microstructures in the DS samples in the vicinity of the section change have been studied in order to examine the effect of convection associated with the combined influence of thermosolutal effects and solidification shrinkage. Extensive radial and axial macrosegregation associated with cross-section change is observed. It also appears that steepling and local primary alpha-phase remelting resulting from convection are responsible for stray grain formation at the reentrant corners. Preliminary results from a numerical model, which includes solidification shrinkage and thermosolutal convection in the mushy zone, indicate that these regions are prone to solutal remelting of dendrites.

Ghods, Masoud↗

Macrosegregation Caused by Convection Associated with Directional Solidification through Cross-Section Change

Al-7 wt% Si and Pb-6 wt% Sb alloy samples were directionally solidified (DS), with liquid above and solid below and gravity pointing down, in cylindrical graphite crucibles through an abrupt cross-section change. Fraction eutectic distribution in the microstructure, primary dendrite spacing and primary dendrite trunk diameters have been measured in the DS samples in the vicinity of section change in order to examine the effect of convection associated with the combined influence of thermosolutal factors and solidification shrinkage. It is observed that convection not only produces extensive radial and axial macrosegregation near cross-section change, it also affects the dendritic array morphology. Primary dendrite spacing and primary dendrite trunk diameter, both, are influenced by this convection. In addition to the experimental results, preliminary results from a numerical model which includes solidification shrinkage and thermosolutal convection in the mushy zone in its analysis will also be presented

Ghods, M.↗