Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Comparison of Extensive Thermal Cycling Effects on Microstructure Development in Micro-alloyed Sn-Ag-Cu Solder Joints

Pb-free solder alloys based on the Sn-Ag-Cu (SAC) ternary eutectic have promise for widespread adoption across assembly conditions and operating environments, but enhanced microstructural control is needed. Micro-alloying with elements such as Zn was demonstrated for promoting a preferred solidification path and joint microstructure earlier in simple (Cu/Cu) solder joints studies for different cooling rates. This beneficial behavior now has been verified in reworked ball grid array (BGA) joints, using dissimilar SAC305 (Sn-3.0Ag-0.5Cu, wt.%) solder paste. After industrial assembly, BGA components joined with Sn-3.5Ag-0.74Cu-0.21Zn solder were tested in thermal cycling (-55 C/+125 C) along with baseline SAC305 BGA joints beyond 3000 cycles with continuous failure monitoring. Weibull analysis of the results demonstrated that BGA components joined with SAC + Zn/SAC305 have less joint integrity than SAC305 joints, but their lifetime is sufficient for severe applications in consumer, defense, and avionics electronic product field environments. Failure analysis of the BGA joints revealed that cracking did not deviate from the typical top area (BGA component side) of each joint, in spite of different Ag3Sn blade content. Thus, SAC + Zn solder has not shown any advantage over SAC305 solder in these thermal cycling trials, but other characteristics of SAC + Zn solder may make it more attractive for use across the full range of harsh conditions of avionics or defense applications.

36 MATERIALS SCIENCE↗

Fabrication of AZ31/MWCNTs Surface Metal Matrix Composites by Friction Stir Processing: Investigation of Microstructure and Mechanical Properties

The surface metal matrix composites of AZ31 Mg alloy reinforced with multiwall carbon nanotubes (MWCNTs) have been fabricated through the friction stir processing by a conventional and two stepped tools. The microstructure and mechanical properties of fabricated composites were studied by optical and electron microscopy, microhardness and tensile tests, respectively. The processing has developed a fine-grain structure along with good distribution of reinforcements. The hardness and tensile strength of fabricated MWCNT/AZ31 composites are generally higher than as-received and FSPed samples. The accumulative effect of grain refinement and reinforcing nanotubes is assumed to be the reason for increasing the ductility after friction stir processing. The hardness is nearly doubled for FSPed samples and some more for nanocomposites compared with the as-received sample. The elongation of nanocomposites is about two times greater than that of the as-rolled sample. The speed ratio, pass number and CNT amount are three important factors influencing the resulting microstructure and mechanical properties. The stepped tools also give a more uniform distribution of reinforcement and higher grain refinement.

36 MATERIALS SCIENCE↗

Effect of Tempering Temperature on the Microstructure and Properties of Fe-2Cr-Mo-0.12C Pressure Vessel Steel

To obtain the high-temperature strength and toughness of the medium–high-temperature–pressure steel, the microstructure evolution and mechanical properties of Fe-2Cr-Mo-0.12C steel subjected to three different tempering temperatures after being normalized were investigated. The results show that the microstructure of the sample, tempered in the range 675-725 °C for 50 min, did not change dramatically, yet the martensite/austenite constituents decomposed, and the bainite lath merged together and transformed into polygonal ferrite. At the same time, the precipitate size increased with an increase in tempering temperature. With the increase in the tempering temperature from 675 to 725 °C, the impact absorbed energy of the Fe-2Cr-Mo-0.12C steel at −40 °C increased from 257 to 325 J, and the high-temperature yield strength decreased; however, the high-temperature ultimate tensile strength tempered at 700 °C was outstanding (422-571 MPa) at different tested temperatures. The variations of the properties were attributed to the decomposition of M/A constituents and the coarsening of the precipitates. Fe-2Cr-Mo-0.12C steel normalized at 930 °C and tempered at 700 °C was found to have the best combination of ductility and strength.

36 MATERIALS SCIENCE↗

Effects of Overlapping Distances on Steel Microstructure and Properties After Multi-track Laser Quenching

In this study, multi-track laser quenching with different overlapping distances was used to assess SM45C microstructure and properties. Two overlapping distance types were evaluated, including overlapping distances in the transition and martensite regions, respectively. After multi-track quenching, hardness showed a threefold increase. With the overlapping distance in the transition region, surface hardness varied from 600 to 700 HV. There was a region of low hardness in each track. Hardness in the low hardness region was from 300 to 400 HV. The average hardness was basically over 500 HV with the overlapping distance in the martensite region, although there was a softening region. The increased hardness was mainly caused by the martensite. Microstructure in the overlapping region was self-tempered martensite, retained austenite and ferrite. Tempered sorbite and lowly tempered martensite were observed in heat-affected zones. Friction coefficients of quenched specimens varied between 0.275 and 0.325, with a 14% reduction relative to the base metal. The wear rate of the quenched specimen was only 40.8% of the base metal. With time, mass reduction in the quenched specimen was much smaller than that of the base metal. For specimens treated with laser quenching, slight fatigue wear was dominating.

36 MATERIALS SCIENCE↗

Microstructure Evolution During Continuous Cooling in AISI 5140 Steel Processed by Induction Heating Chromizing

In this study, induction heating chromizing (IHC) and box-type furnace heating chromizing (BFHC) were conducted on commercial AISI 5140 steels, respectively. Microstructure, microhardness and wear resistance of the chromized samples were characterized. The results show that the IHC samples have thicker Cr coating layer and stronger interface bond due to pre-compressive stress among the packed powders. Three kinds of microstructures including alloyed cementite (AC-layer), fine pearlite zone (FP-zone) and carbon-poor zone (CP-zone) are formed near the interface in the IHC samples. The main reason given for this is that different contents of Cr and C have different effects on pearlite phase and morphology. The IHC sample shows better wear properties due to its stronger interface bonding strength than that of the BFHC sample. The formation mechanism of CP-zone and its influences on microhardness and wear resistance are also discussed.

36 MATERIALS SCIENCE↗

Surface Layers of Zr-18%Nb Alloy Modified by Ultrasonic Impact Treatment: Microstructure, Hardness and Corrosion

Near-surface layers in Zr-18%Nb alloy were modified using ultrasonic impact treatment (UIT). The effects of the UIT processing time on a microstructural formation, omega/alpha precipitations, microhardness and corrosion are analyzed. XRD analysis, TEM and SEM observations and EDX characterization allow establishing the links between the microstructure, microhardness and corrosion behavior of the surface layers formed. At the strain extent up to e ≈ 0.3, structural formation occurs under influence of deformation induced heating, which facilitates omega precipitation in beta phase and mechanically induced oxygen transport and oxide formation. XRD analysis reveals moderate compressive residual stresses (− 160 MPa) and pronounced {110} texture after the UIT process. Generation of dislocations and hindering of their movement by nanoscale omega precipitates manifest themselves as the broadening of diffraction peaks occurred mainly owing to the lattice microstrains, and they provide marked strain hardening. The enhanced anticorrosion properties of Zr-18%Nb alloy in saline solution were concluded to be a result of the formation of a protective oxide film, {110} texture and compressive stresses.

36 MATERIALS SCIENCE↗

Microstructure and Interfacial Shear Strength in W/(Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5}){sub 100−x}Nb{sub x} Composites

In the present study, (Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5}){sub 100−x}Nb{sub (x=0,1,2,3)} bulk metallic glass matrix/tungsten wire composites were fabricated by a gas pressure infiltration process at temperature 950 °C for 5 min. Microstructural studies and mechanical behaviors of the materials have been investigated by scanning electron microscopy, transmission electron microscopy and pullout tests. The mechanical results showed that the interface shear strength in the composite sample with X = 2 increased more than twice compared to the composite sample with X = 0. Based on the microstructural results, the addition of two atomic percent Nb in the matrix composite causes an increase in the diffusion band thickness during the melt infiltration and change in the interface fracture mode as a result of pullout test.

36 MATERIALS SCIENCE↗

The Evolution of the Weld Metal Microstructures in Dissimilar Titanium Welds Based on Al and Mo Equivalents

CO{sub 2} laser welding of Ti-15V-3Cr-3Al-3Sn to Ti-4.5Al-3V-2Fe-2Mo was conducted in the study. The notched fracture and microstructures of the weld metal (WM) with various post-weld aging treatments were studied. In the as-welded sample, the WM comprised only β phase, which was relatively soft and ductile. Moreover, the phase constituent of the as-welded WM was related to the Al and Mo equivalents and further compared with other welds. The microstructural morphologies and microhardness of the WMs of dissimilar welds exhibited significant changes after post-weld aging at distinct temperatures. Increasing the Al equivalent ([Al]{sub EQ}) of the WM caused an increased response to age-hardening during post-weld aging treatments. When the aging temperature was increased from 426 to 593 °C, the α precipitates in the WM grew in size, causing a decrease in hardness, but an improvement in toughness.

36 MATERIALS SCIENCE↗

An EBSD Evaluation of the Microstructure of Crept Nimonic 101 for the Validation of a Polycrystal–Plasticity Model

Nimonic 101 is one of the early nickel-based superalloys developed for the use in gas turbines. In such environments, the material is exposed to a combination of both high temperatures and mechanical loads for a long duration. Hence, thermal creep is of the utmost concern as it often limits service life. This study focuses on creep tests, carried out on Nimonic 101 at different temperatures under a constant tensile load of 735 MPa. To characterize the microstructural evolution, electron backscatter diffraction (EBSD) measurements were employed before and after loading. At higher temperatures, a significant change of the microstructure was observed. The grains elongated and aligned their orientation along the load axis. In parallel, a crystal plasticity material model has been set up in the classical large deformation framework. Modeling results are compared to the acquired EBSD data.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Failure Analysis of an Aluminum–Copper Cathode Conductive Head Produced by Explosive Welding

In this paper, microstructure evolution and failure analysis of the aluminum-copper interface of cathode conductive heads during their use were studied. The interface morphologies, compositions, conductivity and mechanical properties were investigated and analyzed. Obvious corrosion was found on the surface of the contact interface, which was more prevalent on an Al matrix. The crack increased sharply in the local metallurgical bonding areas on the interface, with the compound volume having no significant change. The phase transformation occurred on the interface during use, which was investigated using the elemental composition and x-ray diffraction pattern. The microhardness near the interface increased accordingly. An obvious electrical conductivity decrease appeared on the Al/Cu interface of the cathode conductive head after use over a specific time interval. Therefore, the deterioration of the microstructures and corrosion are the primary factors that affect the electrical conductivity and effective bonding, which will lead to eventual failure.

36 MATERIALS SCIENCE↗

The Effect of SiC Addition on Microstructure and Mechanical Properties of Gas Tungsten Arc-Welded Ti-6Al-4V Alloy

In the present study, SiC powder was added in situ for bead-on-plate weldments and fusion butt joints to modify the microstructure and the corresponding mechanical properties. Cross sections of bead-on-plate welds demonstrated that the SiC addition resulted in significant changes of the titanium microstructure. Specifically, a fine lamellar structure of α-phase with a small amount of intergranular β-titanium within the fusion zone could be established. Moreover, the size of prior β-grains was significantly reduced. After welding, no intermetallic silicides were observed. In the fusion zone of the SiC-enhanced samples, a small increase in hardness resulted, and the samples showed an increase in tensile strength, yield strength and elongation.

36 MATERIALS SCIENCE↗

Comparative Analysis of the Microstructural Features of 28 wt.% Cr Cast Iron Fabricated by Pulsed Plasma Deposition and Conventional Casting

The effect of pulsed plasma deposition (by an electrothermal axial plasma accelerator) followed by post-heat treatment on the structure and microhardness of a 28 wt.% Cr white cast iron is analyzed and discussed with respect to the microstructure of the conventionally cast monolithic counterpart. The cast iron (as deposited on a 14 wt.% Cr cast iron substrate) had a microhardness of 630-750 HV{sub 0.05}; it had layered light contrast/dark contrast structure where dark contrast layers contain fine carbide network. Pulsed plasma deposition followed by heat treatment resulted in a substantial refinement of the microstructure: eutectic M{sub 7}C{sub 3} coarse acicular plates in the conventional cast iron were replaced by fine M{sub 7}C{sub 3}, M{sub 3}C{sub 2}, M{sub 3}C particles (Cr depleted in favor of Fe), while the initial carbide particle of 2-3 μm was reduced to 0.6 μm. Secondary dendrite arm spacing decreased from 15 to 1.3 μm, accordingly. The carbide volume fraction in the post-heat-treated coating remarkably increased with respect to the conventional counterpart resulting in a substantial increase in the coating hardness (1300-1750 HV{sub 0.05}). The heat-treated coating displayed higher resistance to three-body abrasion than the as-deposited coating and similar resistance with that of the conventionally cast iron.

36 MATERIALS SCIENCE↗

The Mechanical and Microstructural Changes of Sn-Ag-Bi Solders with Cooling Rate and Bi Content Variations

The purpose of this study is to investigate the influence of cooling rate and Bi addition on the microstructure evolution and mechanical properties of Sn-3.5Ag alloy. A series of Sn-3.5Ag-xBi solders has been fabricated with Bi content in the range of 0.5-3.5 wt.%. After solution heat treatment at 170 °C for 24 h and subsequent aging heat treatment at 100 °C for 2 h, samples were divided into two groups. One group was rapidly quenched into iced water (water quenching) for the fast cooling rate (20 °C/s), while the second group was slowly cooled (furnace cooling) in the furnace for the slow cooling rate (0.2 °C/s) after the furnace reflow. The microstructural evolutions of the present solders have been investigated using x-ray diffraction and scanning electron microscopy. The microhardness was measured to correlate the mechanical properties to alloy compositions and cooling rate. It was found that the microhardness of Sn-3.5Ag-xBi solders increased with increasing cooling rate. The indentation creep curves have been evaluated from the obtained microhardness values. Results revealed the steady-state creep rate decreased with increasing Bi content exhibiting an anomalous behavior at 2.5Bi. The reason for improved creep resistance of Sn-3.5Ag-xBi solders is the result of the combination of the solid solution strengthening and precipitation strengthening of Bi. The mean values of stress exponent indicated that the operative creep mechanism is dislocation climb.

36 MATERIALS SCIENCE↗

Microstructure Characteristic and Mechanical Properties of High-Strength Mg-Nd-Zn-Zr Alloy Seamless Tube Produced by Integrated Extrusion

Large size seamless tubes of Mg-3.0Nd-0.4Zn-0.4Zr alloy (NZ30K, in weight percent) were prepared by integrating backward extrusion with forward extrusion. Microstructure, mechanical properties, aging behavior and texture of the tubes were investigated. The microstructure of as-extruded tube is characterized by the blend of considerably elongated grains and fine equiaxed grains. The maximum values of yield strength and ultimate tensile strength, i.e., 191 and 245 MPa, were obtained in the as-extruded tubes, and these values were increased to 212 and 267 MPa in the peak-aged tubes (T5), implying an increasing ratio of 9 and 11%, respectively. The peak value of the Vickers’ micro-hardness of the NZ30K tubes extruded at 673, 723 and 753 K are 66, 64 and 60 (kilogram-force per square millimeter), respectively. The texture of NZ30K tube is weak, the primary mechanism behind which is suggested to be the particle-induced nucleation responsible for the promotion of recrystallization.

36 MATERIALS SCIENCE↗

Ca Addition Effects on the Microstructure, Tensile and Corrosion Properties of Mg Matrix Alloy Containing 8 wt.% Mg{sub 2}Si

The microstructure, tensile properties and corrosion behavior of the Mg-8 wt.% Mg{sub 2}Si-x%Ca alloy have been studied by the use of optical microscopy, scanning electron microscopy equipped with energy-dispersive spectroscopy, x-ray diffraction, standard tensile testing, polarization test and electrochemical impedance spectroscopy (EIS) measurements. Microstructural studies indicated that Ca modifies both primary and eutectic Mg{sub 2}Si phase. It was found that the average size of primary Mg{sub 2}Si particles is about 60 μm, which is dropped by about 82% in the alloy containing 0.05 wt.% Ca. By the addition of different Ca contents, Ca-rich intermetallics (i.e., CaSi{sub 2} and CaMgSi) were formed. The modification mechanism of adding Ca during solidification was found to be due to the strong effect of CaMgSi phase as a heterogonous nucleation site, apart from CaSi{sub 2} which was reported before, for Mg{sub 2}Si intermetallics. Tensile testing results ascertained that Ca addition enhances both ultimate tensile strength (UTS) and elongation values. The optimum amount of Ca was found to be 0.1 wt.%, which improved UTS and elongation values from about 130 MPa and 2% to 165 MPa and 5.5%, whereas more Ca addition (i.e., 3 wt.%) reduced the tensile properties of the alloy to about 105 MPa and 1.8%, which can be due to the formation of CaMgSi intermetallics with deteriorating needle-like morphology. Polarization and EIS tests also showed that the Mg-3%Si-0.5%Ca alloy pronounces as the best anti-corrosion alloy. Nevertheless, further added Ca (up to 3 wt.%) deteriorated the corrosion resistance due to predominance of worse galvanic coupling effect stemmed from the presence of stronger CaMgSi cathode in comparison with Mg{sub 2}Si. With higher Ca additions, an adverse effect was seen on corrosion resistance of the Mg-3%Si alloy, as a result of forming a weak film on the alloy specimen surface.

36 MATERIALS SCIENCE↗

Effects of Disodium Phosphate Concentration (Na{sub 2}HPO{sub 4}·2H{sub 2}O) on Microstructure and Corrosion Resistance of Plasma Electrolytic Oxidation (PEO) Coatings on 2024 Al Alloy

Since the electrolyte composition plays a pivotal role in the microstructure and corrosion behavior of plasma electrolytic oxidation (PEO) coatings, the effects of disodium phosphate (Na{sub 2}HPO{sub 4}·2H{sub 2}O) concentration on the microstructure and corrosion resistance of PEO coatings fabricated on 2024 Al alloy were studied in this investigation. Accordingly, electrolyte with four different concentrations of phosphate ion (5, 10, 15 and 20 g/L) was used. All PEO processes were conducted at constant current density of 15 A/dm{sup 2} for 15 min. The surface and cross-sectional morphologies of the coatings indicated that the coating formed in the electrolyte with 10 g/L Na{sub 2}HPO{sub 4}·2H{sub 2}O (with 9.14 µm thickness) had the most compact and uniform structure with the lowest and smallest micropores. Furthermore, studying the corrosion behavior of samples in 3.5 wt.% NaCl solutions by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests revealed that the sample coated in the electrolyte with 10 g/L Na{sub 2}HPO{sub 4}·2H{sub 2}O had the highest corrosion potential, the lowest corrosion current density and, accordingly, the best corrosion resistance. The corrosion resistance of this coating was 4.574 × 10{sup 5} Ω cm{sup 2}, which could increase the corrosion resistance of uncoated 2024 Al alloy substrate 48 times. The x-ray diffraction pattern of this coating proved that the coating was composed of α-Al{sub 2}O{sub 3} and γ-Al{sub 2}O{sub 3} phases.

36 MATERIALS SCIENCE↗

Adiabatic Shear Localization and Microstructure in Ultrafine Grained Aluminum Alloy at Cryogenic Temperature

Adiabatic shear localization plays an important role in the deformation and failure of ultrafine grained 6061 aluminum alloy processed by friction stir processing. To understand the effects of temperature and strain on adiabatic shear localization in the ultrafine grained 6061 aluminum alloy, it has been investigated dynamic mechanical behavior of ultrafine grained 6061 aluminum alloy under the controlled shock loading experiments. Deformation characteristics and microstructures in the shear band were performed by optical microscopy and transmission electron microscopy. The shear band in the ultrafine grained aluminum alloy is a long and straight band distinguished from the matrix. The width of the shear band decreases with increasing nominal strain. The results show that the grains in the boundary of the shear band are highly elongated along the shear direction and form the elongated cell structures (0.2 μ in width), and the core of the shear band consists of a number of recrystallized equiaxed grains 0.2-0.3 μ in diameters and the second phases distribute in both the boundary and the inner of the equiaxed new grains. The calculated temperature in the shear band is about 692 K. Rotational dynamic recrystallization mechanism is responsible for the formation of the microstructure in the shear band.

36 MATERIALS SCIENCE↗

Tensile Deformation Temperature Impact on Microstructure and Mechanical Properties of AISI 316LN Austenitic Stainless Steel

Uniaxial tensile tests were conducted on AISI 316LN austenitic stainless steel from − 40 to 300 °C at a rate of 0.5 mm/min. Microstructure and mechanical properties of the deformed steel were investigated by optical, scanning and transmission electron microscopies, x-ray diffraction, and microhardness testing. The yield strength, ultimate tensile strength, elongation, and microhardness increase with the decrease in the test temperature. The tensile fracture morphology has the dimple rupture feature after low-temperature deformations and turns to a mixture of transgranular fracture and dimple fracture after high-temperature ones. The dominating deformation microstructure evolves from dislocation tangle/slip bands to large deformation twins/slip bands with temperature decrease. The deformation-induced martensite transformation can only be realized at low temperature, and its quantity increases with the decrease in the temperature.

36 MATERIALS SCIENCE↗