SEARCH · Search NASA

Results for “PERMANENT MAGNETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

All sources NASA NTRS DOE OSTI

DOE OSTI2013

Development of a Residential Ground-Source Integrated Heat Pump

A residential-size ground-source integrated heat pump (GSIHP) system has been developed and is currently being field tested. The system is a nominal 2-ton (7 kW) cooling capacity, variable-speed unit, which is multi-functional, e.g. space cooling, space heating, dedicated water heating, and simultaneous space cooling and water heating. High-efficiency brushless permanent-magnet (BPM) motors are used for the compressor, indoor blower, and pumps to obtain the highest component performance and system control flexibility. Laboratory test data were used to calibrate a vapor-compression simulation model (HPDM) for each of the four primary modes of operation. The model was used to optimize the internal control options and to simulate the selected internal control strategies, such as controlling to a constant air supply temperature in the space heating mode and a fixed water temperature rise in water heating modes. Equipment performance maps were generated for each operation mode as functions of all independent variables for use in TRNSYS annual energy simulations. These were performed for the GSIHP installed in a well-insulated 2600 ft2(242 m2) house and connected to a vertical ground loop heat exchanger(GLHE). We selected a 13 SEER (3.8 CSPF )/7.7 HSPF (2.3 HSPF, W/W) ASHP unit with 0.90 Energy Factor (EF) resistance water heater as the baseline for energy savings comparisons. The annual energy simulations were conducted over five US climate zones. In addition, appropriate ground loop sizes were determined for each location to meet 10-year minimum and maximum design entering water temperatures (EWTs) to the equipment. The prototype GSIHP system was predicted to use 52 to 59% less energy than the baseline system while meeting total annual space conditioning and water heating loads.

Energy Efficiency↗

DOE OSTI2013

Active combustion flow modulation valve

A flow modulation valve has a slidably translating hollow armature with at least one energizable coil wound around and fixably attached to the hollow armature. The energizable coil or coils are influenced by at least one permanent magnet surrounding the hollow armature and supported by an outer casing. Lorentz forces on the energizable coils which are translated to the hollow armature, increase or decrease the flow area to provide flow throttling action. The extent of hollow armature translation depends on the value of current supplied and the direction of translation depends on the direction of current flow. The compact nature of the flow modulation valve combined with the high forces afforded by the actuator design provide a flow modulation valve which is highly responsive to high-rate input control signals.

42 ENGINEERING↗

DOE OSTI2016

Flywheel system using wire-wound rotor

A flywheel is described having a rotor constructed of wire wound onto a central form. The wire is prestressed, thus mitigating stresses that occur during operation. In another aspect, the flywheel incorporates a low-loss motor using electrically non-conducting permanent magnets.

25 ENERGY STORAGE↗

DOE OSTI2016

Method for producing La/Ce/MM/Y base alloys, resulting alloys and battery electrodes

A carbothermic reduction method is provided for reducing a La-, Ce-, MM-, and/or Y-containing oxide in the presence of carbon and a source of a reactant element comprising Si, Ge, Sn, Pb, As, Sb, Bi, and/or P to form an intermediate alloy material including a majority of La, Ce, MM, and/or Y and a minor amount of the reactant element. The intermediate material is useful as a master alloy for in making negative electrode materials for a metal hydride battery, as hydrogen storage alloys, as master alloy additive for addition to a melt of commercial Mg and Al alloys, steels, cast irons, and superalloys; or in reducing Sm.sub.2O.sub.3 to Sm metal for use in Sm--Co permanent magnets.

25 ENERGY STORAGE↗

DOE OSTI2016

R 5 T 4 compounds - unique multifunctional intermetallics for basic research and applications

The unique properties of the rare-earth elements and their alloys have brought them from relative obscurity to high profile use in common high-tech applications. The broad technological impact of these remarkable materials may have never been known by the general public if not for the supply concerns that placed the rare-earth materials on the front page of newspapers and magazines. Neodymium and dysprosium, two essential components of Nd 2 Fe 14 B-based high-performance permanent magnets, have drawn much attention and have been deemed critical materials for many energy-related applications. Ironically, the notoriety of rare-earth elements and their alloys is the result of a global movement to reduce their use in industrial applications and, thus, ease concerns about their supply and ultimately to reduce their position in high-tech supply chains. Research into the applications of lanthanide alloys has been de-emphasized recently due to the perception that industry is moving away from the use of rare-earth elements in new products. While lanthanide supply challenges justify efforts to diversify the supply chain, a strategy to completely replace the materials overlooks the reasons rare earths became important in the first place -- their unique properties are too beneficial to ignore. Rare-earth alloys and compounds possess truly exciting potential for basic science exploration and application development such as solid-state caloric cooling. In this brief review, we touch upon several promising systems containing lanthanide elements that show important and interesting magnetism-related phenomena.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Torque ripple reduction in electric machines

An electric machine, such as an Internal Permanent magnet or Synchronous Reluctance machine, having X phases, that includes a stator assembly, having M slots, with a stator core and stator teeth, that is further configured with stator windings to generate a stator magnetic field when excited with alternating currents and extends along a longitudinal axis with an inner surface that defines a cavity; and a rotor assembly, having N poles, disposed within the cavity which is configured to rotate about the longitudinal axis, wherein the rotor assembly includes a shaft, a rotor core located circumferentially around the shaft. The machine is configured such that a value k=M/(X*N) wherein k is a non-integer greater than about 1.3. The electric machine may alternatively, or additionally, include a non-uniformed gap between the exterior surface of the rotor spokes and the interior stator surface of the stator.

42 ENGINEERING↗

DOE OSTI2018

Rapid consolidation method for preparing bulk metastable iron-rich materials

Interstitially modified compounds of rare earth element-containing, iron-rich compounds may be synthesized with a ThMn.sub.12 tetragonal crystal structure such that the compounds have useful permanent magnet properties. It is difficult to consolidate particles of the compounds into a bulk shape without altering the composition and magnetic properties of the metastable material. A combination of thermal analysis and crystal structure analysis of each compound may be used to establish heating and consolidation parameters for sintering of the particles into useful magnet shapes.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Pulsed start-up system for electrostatic generators

A new rotor start-up system is provided for application to rotating systems such as stationary or vehicular electromechanical battery systems. An embodiment of the system consists of a "locator" that includes a stationary permanent-magnet pole above which is a circular ferromagnetic (e.g., iron) strip embedded in the lower, inner edge of the flywheel rotor. The lower edge of this strip is wave-like so that the magnet can pull the rotor around to a position where the position relative to the minimum capacity between the rotor and stator electrodes is such as to launch the rotor in a chosen direction, i.e., either clock-wise or counter-clockwise. Startup from rest is then accomplished by applying a short high-voltage ac or dc pulse to the EMB capacitor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2019

Pulse Shaping and Matched Filters for EMAT Communication System

Electromagnetic acoustic transducer (EMAT) is used as a noncontact sensor for acoustic communication in a stainless-steel plate channel. The acoustic wave multipath propagations within the channel cause intersymbol interference (ISI). ISI highly degrades the signal-to-noise ratio (SNR). The poor SNR will result in a low bitrate and a high bit error rate (BER). In this study, a test platform is designed to estimate the performance of the EMAT communication system. Two periodic-permanent-magnet (PPM) EMATs are designed to be used as a transmitter and a receiver. EMAT generates shear-horizontal (SH) wave propagating through the stainless-steel plate channel. We present methods to minimize the ISI effect and recover the message embedded in the received signals hampered by interference, reverberation and multipath effects. The root raised cosine (RRC) filters are introduced as a pulse-shaping filter for transmission and a matched filter for receiving messages. Amplitude Shift Keying (ASK) method is used for modulating the transmitted binary message. The pulse shaping and matched filters reduced the ISI caused by the undesirable multipath effect significantly to the extent that a 5-kbps bitrate can be achieved without any error (zero BER).

Huang, Xin↗

DOE OSTI2019

Compac carbon ion LINAC

The invention provides a method for accelerating protons and carbon ions up to 450 MeV/u in a very compact linac, the method comprising subjecting the particles to a radio frequency quadrupole field to accelerate the particles to at least 3 MeV/u, a drift tube linac (DTL) to an energy of 20 MeV/u, followed by a coupled DTL to 45 MeV/u and finally a high-gradient section made of CCL-type standing wave cavities or negative harmonic traveling wave cavities operating at S-band frequencies and capable of delivering voltage gradients of 40 to 60 MV/m. Focusing the accelerated particles while accelerated to higher energy is provided by appropriately placed constant field permanent magnets and electromagnetic quadrupoles. The compactness and power efficiency of the linac is enabled by using high-gradient structure in the S-band frequencies for lower energy particles than ever before. The low-intensity required for hadron therapy allows the use of small-aperture S-band structures and the operation at very high gradient compared to high-intensity machines for research. Operating with very short sub-microsecond pulses at repetition rates up to 400 Hz allows the fast and flexible beam energy and intensity tuning not provided by existing hadron therapy machines. The designed linac is capable of accelerating ions as heavy as neon to the full 450 MeV/u energy, therefore allowing fast beam switching if different ion sources are installed in the front-end of the linac.

43 PARTICLE ACCELERATORS↗

DOE OSTI2019

Method for producing La/Ce/MM/Y base alloys, resulting alloys, and battery electrodes

A carbothermic reduction method is provided for reducing a La-, Ce-, MM-, and/or Y-containing oxide in the presence of carbon and a source of a reactant element comprising Si, Ge, Sn, Pb, As, Sb, Bi, and/or P to form an intermediate alloy material including a majority of La, Ce, MM, and/or Y and a minor amount of the reactant element. The intermediate material is useful as a master alloy for in making negative electrode materials for a metal hydride battery, as hydrogen storage alloys, as master alloy additive for addition to a melt of commercial Mg and Al alloys, steels, cast irons, and superalloys; or in reducing Sm2O3 to Sm metal for use in Sm—Co permanent magnets.

25 ENERGY STORAGE↗

DOE OSTI2020

Method of making iron nitride powder with anisotropic shape

Techniques are disclosed for milling an iron-containing raw material in the presence of a nitrogen source to generate anisotropically shaped particles that include iron nitride and have an aspect ratio of at least 1.4. Techniques for nitridizing an anisotropic particle including iron, and annealing an anisotropic particle including iron nitride to form at least one a″-Fe16N2 phase domain within the anisotropic particle including iron nitride also are disclosed. In addition, techniques for aligning and joining anisotropic particles to form a bulk material including iron nitride, such as a bulk permanent magnet including at least one a″-Fe16N2 phase domain, are described. Milling apparatuses utilizing elongated bars, an electric field, and a magnetic field also are disclosed.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Dissolution and separation of rare earth metals

A chemical dissolution method is provided for use in recycling rare earth metal-containing material such as permanent magnet material including end-of-life magnet shapes, magnet scrap and Terfenol-D alloy material by mixing the rare earth metal-containing material and an aqueous solution of a copper (II) salt to dissolve the material in the solution. The dissolved rare earth metal is then precipitated from the aqueous solution as a rare earth metal compound, such as a rare earth metal oxalate, sulfate or phosphate from which rare earth metal oxide can be obtained.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Pulsed start-up system for electrostatic generators

A new rotor start-up system is provided for application to rotating systems such as stationary or vehicular electromechanical battery systems. An embodiment of the system consists of a “locator” that includes a stationary permanent-magnet pole above which is a circular ferromagnetic (e.g., iron) strip embedded in the lower, inner edge of the flywheel rotor. The lower edge of this strip is wave-like so that the magnet can pull the rotor around to a position where the position relative to the minimum capacity between the rotor and stator electrodes is such as to launch the rotor in a chosen direction, i.e., either clock-wise or counter-clockwise. Startup from rest is then accomplished by applying a short high-voltage ac or dc pulse to the EMB capacitor.

42 ENGINEERING↗

DOE OSTI2021

Rapid consolidation method for preparing bulk metastable iron-rich materials

Interstitially modified compounds of rare earth element-containing, iron-rich compounds may be synthesized with a ThMn 12 tetragonal crystal structure such that the compounds have useful permanent magnet properties. It is difficult to consolidate particles of the compounds into a bulk shape without altering the composition and magnetic properties of the metastable material. A combination of thermal analysis and crystal structure analysis of each compound may be used to establish heating and consolidation parameters for sintering of the particles into useful magnet shapes.

Zhou, Chen↗

DOE OSTI2022

FNAL PIP-II Accumulator Ring

The FNAL accelerator complex is poised to reach MW neutrino beams on target for the exploration of the dark sector physics and rare physics program spaces. Future operations of the complex will include CW linac operations at beam intensities that have not been seen before \cite{PIP2,RCS_LOI}. The ambitious beam program relies on multi-turn H$^{-}$ injection into the FNAL Booster and then extracted into delivery rings or the Booster Neutrino Beam (BNB) 8 GeV HEP program. A new rapid-cycling synchrotron (RCS) will be required to reach the LBNF goal of 2.4 MW because of intense space-charge limitations. There are many accelerator engineering challenges that are already known and many that will be discovered. This proposal calls for an intermediate step that will both facilitate the operation of Booster in the PIP-II era and gain operational experience associated with high power injection rings. This step includes the design, construction and installation of a 0.8 GeV accumulator ring (upgradeable to 1+ GeV) to be located in the PIP-II Booster Transfer Line (BTL). The PIP-II accumulator ring (PAR) may be primarily designed around permanent magnets or use standard iron core magnet technology with an aperture selected to accommodate the desired high intensity protons at 0.8 GeV.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Investigation of Rare Earth Elements Mobility Using Molecular Dynamics

Rare Earth Elements (REE) are critical many applications such as electronics, permanent magnets, agricultural etc. Effective separation of REEs is a challenge due to their similarities in chemical and physical properties. Current separation processes are costly and environmentally detrimental. Therefore, research on REEs mobility in water-based solvents is necessary to design effective separation processes. In this research, the key kinetic and thermodynamic parameters, including diffusion coefficient and hydration shell are determined under the influence of external electric field. The diffusion coefficient of metal ions increases due to electric field in pure water.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2022

Investigation of Rare Earth Elements Mobility Using Molecular Dynamics

99 GENERAL AND MISCELLANEOUS↗