Search NASA⌕ Search

SEARCH · Search NASA

Results for “Particle separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Active Control of Separation From the Flap of a Supercritical Airfoil

Zero-mass-flux periodic excitation was applied at several regions on a simplified high-lift system to delay the occurrence of flow separation. The NASA Energy Efficient Transport (EET) supercritical airfoil was equipped with a 15% chord simply hinged leading edge flap and a 25% chord simply hinged trailing edge flap. Detailed flow features were measured in an attempt to identify optimal actuator placement. The measurements included steady and unsteady model and tunnel wall pressures, wake surveys, arrays of surface hot-films, flow visualization, and particle image velocimetry (PIV). The current paper describes the application of active separation control at several locations on the deflected trailing edge flap. High frequency (F(+) approximately equal to 10) and low frequency amplitude modulation (F(+) sub AM approximately equal to 1) of the high frequency excitation were used for control. It was noted that the same performance gains were obtained with amplitude modulation and required only 30% of the momentum input required by pure sine excitation.

Melton, LaTunia Pack↗

Final Report on Actinide Glass Scintillators for Fast Neutron Detection

This is the final report of an experimental investigation of actinide glass scintillators for fast-neutron detection. It covers work performed during FY2012. This supplements a previous report, PNNL-20854 “Initial Characterization of Thorium-loaded Glasses for Fast Neutron Detection” (October 2011). The work in FY2012 was done with funding remaining from FY2011. As noted in PNNL-20854, the glasses tested prior to July 2011 were erroneously identified as scintillators. The decision was then made to start from “scratch” with a literature survey and some test melts with a non-radioactive glass composition that could later be fabricated with select actinides, most likely thorium. The normal stand-in for thorium in radioactive waste glasses is cerium in the same oxidation state. Since cerium in the 3+ state is used as the light emitter in many scintillating glasses, the next most common substitute was used: hafnium. Three hafnium glasses were melted. Two melts were colored amber and a third was clear. It barely scintillated when exposed to alpha particles. The uses and applications for a scintillating fast neutron detector are important enough that the search for such a material should not be totally abandoned. This current effort focused on actinides that have very high neutron capture energy releases but low neutron capture cross sections. This results in very long counting times and poor signal to noise when working with sealed sources. These materials are best for high flux applications and access to neutron generators or reactors would enable better test scenarios. The total energy of the neutron capture reaction is not the only factor to focus on in isotope selection. Many neutron capture reactions result in energetic gamma rays that require large volumes or high densities to detect. If the scintillator is to separate neutrons from gamma rays, the capture reactions should produce heavy particles and few gamma rays. This would improve the detection of a signal for fast neutron capture.

Actinide Glass↗

High-performance Ni–BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb) membranes for hydrogen separation

Cermet membranes composited of Ni and doped barium cerate have been widely studied for hydrogen separation; however, their practical application is limited primarily by the relatively low permeation rate and instability of doped barium cerate in H 2 O and CO 2 containing gases. Here we report our findings on the development of a thin-film cermet membrane consisting of Ni and BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb), supported on a porous Ni–BZCYYb substrate. High fluxes of 1.12 and 0.49 ml min -1 cm -2 have been demonstrated at 900 °C and 700 °C, respectively, when hydrogen was used as the feed gas on one side and N2 as the sweep gas on the other side. Most importantly, the high-performance membrane can be easily fabricated by a cost-effective particle-suspension coating/co-firing process, offering great promise for large scale hydrogen separation applications.

08 HYDROGEN↗

Electrostatic interaction effect for human DNA separation with functionalized mesoporous silicas

This work describes the development of highly efficient human DNA separation with functionalized mesoporous silica (FMS) materials. To demonstrate the electrostatic interaction effect between the target DNA molecules and FMS, three aminofunctionality types comprised of a mono-, a di-, and a tri-amine functional group were introduced on the inner surfaces of mesoporous silica particles. Systematic characterization of the synthesized materials was achieved by solid-state {sup 29}Si and {sup 13}C-NMR techniques, BET, FT-IR, and XPS. The DNA separation efficiency was explored via the function of the amino-group number, the amount used, and the added NaCl concentration. The DNA adsorption yields were high in terms of the use of triaminofunctionalized FMS at the 10 ng/L level, and the DNA desorption efficiency showed the optimum level at over 3.0 M NaCl concentration. The use of FMS in a DNA separation process provides numerous advantages over the conventional silica-based process. -- Graphical abstract: Control of electrostatic interaction for DNA biding by aminofunctionalized modification: mono-amine (MA), di-amine (DA), and tri-amine (TA). The red-ball means the amine groups of FMS. Display Omitted Highlights: {yields} Highly efficient and direct DNA separation was demonstrated with aminofunctionalized FMS. {yields} Systematic characterization of the synthesized materials was achieved by solid-state {sup 29}Si and {sup 13}C-NMR techniques, BET, FT-IR, and XPS. {yields} The DNA separation efficiency was explored via the function of the amino-group number, particles size, amount of FMS used, and the NaCl concentration. {yields} The electrostatic interaction between the target DNA labeled by cyanine (Cy-5) and aminofunctionalized FMS were achieved via confocal microscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New Hayabusa2 and OSIRIS REx Curation Facilities at Nasa Johnson Space Center

Asteroids are made up of rocky material that is left over from the formation of our solar system [1]. This material holds the key to unlocking information about the history of the planets and our sun. Hayabusa2 and OSIRIS-REx are two sample return missions that have collected rocky material from carbonaceous asteroids which are rich in water, carbon, and organic compounds [1]. Hayabusa2 is a spacecraft that collected samples from asteroid Ryugu launched by the Japan Aerospace Exploration Agency (JAXA). Samples were returned to Earth in December 2020 and 10 percent of the collected material is currently housed in a state-of-the-art laboratory at NASA Johnson Space Center (JSC) dedicated to Ryugu material [1]. OSIRIS-REx is a spacecraft launched by NASA that collected samples from asteroid Bennu. The samples are on their journey to Earth and will arrive in September 2023. They will be stored in a separate cleanroom dedicated to Bennu material. From these two missions, scientists will examine dust particles and rocky material to research clues on how the early solar system formed and how life began [2]. Because these samples are so precious and rare, it is important to keep them free from Earth contamination. In September of 2020, a massive construction project began to provide curation facilities to meet the needs of two incoming asteroid collections, Hayabusa2 and OSIRIS-REx. Despite numerous setbacks caused by the coronavirus pandemic, these facilities have been completed in the fall of 2021. Some of these setbacks included strict PPE requirements, keeping safe working distances as well as access to the facilities as NASA was operating under a Stage 3 condition in response to the pandemic. These facilities will provide curation laboratories to safely house the precious asteroid samples as well as facilities to manipulate samples, do sample preparation and process samples into and out of the labs for future studies by the scientific community. The lab suite consists of several different rooms including an initial anteroom (ISO 7), a staging area (ISO 7), two gowning areas (one for OSIRIS-REx and one for Hayabusa2; both ISO 6)), the Haybusa2 Curation Laboratory (ISO 5), the OSIRIS-REx Curation Laboratory (ISO 5), an ultramicrotomy laboratory (ISO 7) and a thin section laboratory (not a cleanroom). To maintain cleanliness levels necessary for these lab spaces quarterly to monthly Balazs organic and inorganic sampling has been conducted on a regular basis before, during and after the construction project to monitor the cleanliness levels in the new labs that will house the asteroid samples. These new facilities feature a Ruuvi (Grafana) monitoring system that measures temperature, humidity, and pressure of the lab suite. This is a small puck shaped sensor that sends signals to the Grafana cloud where the data can be plotted and set up on dashboards within the lab suite. These sensors are easy to set up and install and they run off a cell battery that is good for 3-5 years before needing replacement. This system can deliver text messages and emails to the appropriate personnel when values fall outside of set limits. In addition to the monitoring system, this new lab suite features viewing windows from several different locations and sliding motion censored doors. We have obtained some state-of-the-art equipment to outfit the lab spaces (desiccators, microscopes, ultramicrotome) and are in the process of outfitting the suite with additional items such as: nitrogen gloveboxes, additional desiccators, micromanipulators, etc. The Hayabusa2 samples provided to NASA by JAXA included 23 millimeter sized grains and 4 containers with finer material. OSIRIS-REx is expected to return as much as 400 grams of asteroid Bennu. Samples will be stored in a nitrogen glove box and separated into nitrogen sealed transfer containers. Small Bennu and Ryugu particles will be handled and prepared (e.g., ultra-thin sections for scanning electron microscopy (SEM) or transmission electron microscopy (TEM)) using an Axis Pro micromanipulator and Leica EM UC7 ultramicrotome. Analyzing samples at the atomic scale will provide greater insight to the origins of the solar system and life formation on Earth. All the curation preparation for these sample collections is essential to ongoing research and efforts to understand our solar system, both nowand for future generations.

Curation↗

Reciprocal swimming at intermediate Reynolds number

In Stokes flow, Purcell's scallop theorem forbids objects with time-reversible (reciprocal) swimming strokes from moving. In the presence of inertia, this restriction is eased and reciprocally deforming bodies can swim. A number of recent works have investigated dimer models that swim reciprocally at intermediate Reynolds numbers Re≈1–1000. These show interesting results (e.g. switches of the swim direction as a function of inertia) but the results vary and seem to be case specific. Here, in this work, we introduce a general model and investigate the behaviour of an asymmetric spherical dimer of oscillating length for small-amplitude motion at intermediate Re. In our analysis we make the important distinction between particle and fluid inertia, both of which need to be considered separately. We asymptotically expand the Navier–Stokes equations in the small-amplitude limit to obtain a system of linear partial differential equations. Using a combination of numerical (finite element) and analytical (reciprocal theorem, method of reflections) methods we solve the system to obtain the dimer's swim speed and show that there are two mechanisms that give rise to motion: boundary conditions (an effective slip velocity) and Reynolds stresses. Each mechanism is driven by two classes of sphere–sphere interactions, between one sphere's motion and (1) the oscillating background flow induced by the other's motion, and (2) a geometric asymmetry induced by the other's presence. We can thus unify and explain behaviours observed in other works. Our results show how sensitive, counterintuitive and rich motility is in the parameter space of finite inertia of particles and fluid.

42 ENGINEERING↗

Redox active colloidal particles for flow batteries

The invention provides a redox flow battery comprising a microporous or nanoporous size-exclusion membrane, wherein one cell of the battery contains a redox-active colloidal particle dispersed in a non-aqueous solvent. The redox flow battery provides enhanced ionic conductivity across the electrolyte separator and reduced redox-active species crossover, thereby improving the performance and enabling widespread utilization of the battery. Redox active colloidal particles (RACs) were prepared, analyzed, and were found to be highly effective redox species for use in redox flow batteries.

Moore, Jeffrey S.↗

Practical considerations in realizing a magnetic centrifugal mass filter

The magnetic centrifugal mass filter concept represents a variation on the plasma centrifuge, with applications that are particularly promising for high-throughput separation of ions with large mass differences. A number of considerations, however, constrain the parameter space in which this device operates best. The rotation speed, magnetic field intensity, and ion temperature are constrained by the ion confinement requirements. Collisions must also be large enough to eject ions, but small enough not to eject them too quickly. The existence of favorable regimes meeting these constraints is demonstrated by a single-particle orbit code. As an example of interest, it is shown that separation factors of about 2.3 are achievable in a single pass when separating Aluminum from Strontium ions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Neon Cluster Formation and Phase Separation during White Dwarf Cooling

Recent observations of Galactic white dwarfs (WDs) with Gaia suggest there is a population of massive crystallizing WDs exhibiting anomalous cooling—the Q branch. While single-particle 22 Ne sedimentation has long been considered a possible heat source, recent work suggests that 22 Ne must separate into clusters, enhancing diffusion, in order for sedimentation to provide heating on the observed timescale. We show definitively that 22 Ne cannot separate to form clusters in C/O WDs using molecular dynamics simulations, and we further present a general C/O/Ne phase diagram showing that strong 22Ne enrichment is not achievable for 22 Ne abundance ≲30%. Here, we conclude that the anomalous heating cannot be due to 22Ne cluster sedimentation and that Q branch WDs may have an unusual composition, possibly rich with heavier elements.

79 ASTRONOMY AND ASTROPHYSICS↗

Quenching of single-particle strength inferred from nucleon-removal transfer reactions on 15 C

The difference in the proton and neutron separation energies (ΔS) of the weakly bound 15 C ground state is -19.86 MeV, an extreme value. Data from intermediate-energy heavy-ion induced (HI-induced) knockout reactions on nuclei spanning -20 ≲ ΔS ≲ +20 MeV, suggest that the degree to which single-particle strength is quenched, R s , has a negative correlation with ΔS, decreasing from unity around -20 MeV to around 0.2 at +20 MeV. For the 15 C ground state (R s = 0.96 (4) in HI-induced knockout), contrasting results have recently been obtained via the neutron-adding transfer reaction, which reveal a value of R s = 0.64 (15), similar to the value observed at modest and more extreme values of ΔS with reaction probes other than HI knockout. In order to explore the any potential differences between adding and removing processes in transfer reactions at extreme ΔS, single-neutron removal transfer reactions on 15 C were performed at 7.1 MeV/u in inverse kinematics. The removal of a valence neutron in 2s 1/2 orbit using both (p, d) and (d, t) reactions shows consistent quenching factors and agrees with those from the neutron-adding reaction. The present results, which can be compared with neutron knockout reaction, suggest that correlations, represented by the quenching factor, show limited dependence on neutron-proton asymmetry under the most extreme asymmetry conditions so far achieved in transfer reactions.

quenching factor↗

Automation of Extraction Chromatograhic and Ion Exchange Separations for Radiochemical Analysis and Monitoring

Radiochemical analysis, complete with the separation of radionuclides of interest from the sample matrix and from other interfering radionuclides, is often an essential step in the determination of the radiochemical composition of a nuclear sample or process stream. Although some radionuclides can be determined nondestructively by gamma spectroscopy, where the gamma rays penetrate significant distances in condensed media and the gamma ray energies are diagnostic for specific radionuclides, other radionuclides that may be of interest emit only alpha or beta particles. For these, samples must be taken for destructive analysis and radiochemical separations are required. For process monitoring purposes, the radiochemical separation and detection methods must be rapid so that the results will be timely. These results could be obtained by laboratory analysis or by radiochemical process analyzers operating on-line or at-site. In either case, there is a need for automated radiochemical analysis methods to provide speed, throughput, safety, and consistent analytical protocols. Classical methods of separation used during the development of nuclear technologies, namely manual precipitations, solvent extractions, and ion exchange, are slow and labor intensive. Fortunately, the convergence of digital instrumentation for preprogrammed fluid manipulation and the development of new separation materials for column-based isolation of radionuclides has enabled the development of automated radiochemical analysis methodology. The primary means for separating radionuclides in solution are liquid-liquid extraction and ion exchange. These processes are well known and have been reviewed in the past.1 Ion exchange is readily employed in column formats. Liquid-liquid extraction can also be implemented on column formats using solvent-impregnated resins as extraction chromatographic materials. The organic liquid extractant is immobilized in the pores of a microporous polymer material. Under suitable conditions, the analyte of interest partitions into the immobilized organic phase while other matrix speces and interferences are washed away in the mobile aqueous phase. After the wash step, retained analytes are rapidly released in one or more steps by changing the aqueous eluent, such that the analytes now partition back into the mobile phase. The development of solvent impregnated resins, their physical chemistry, technological applications for metal and radionuclide recovery, and analytical uses were described in detail in a previous chapter in this series by Cortina and Warshawsky. The extraction chromatographic approach is well suited for the isolation of radionuclides from complex sample matrixes in a rapid automated format. The development of automated radioanalytical methods is, in fact, closely coupled to the availability of such materials. In this review, we will focus on the application of radiochemical separations in automated fluidic formats for the analysis of alpha- and beta-emitting radionuclides.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

The 17 April 2021 Widespread Solar Energetic Particle Event

A complex and long-lasting solar eruption on 17 April 2021 produced a widespread solar energetic particle (SEP) event that was observed by five longitudinally well-separated observers in the inner heliosphere that covered distances to the Sun from 0.42 to 1 au: BepiColombo, Parker Solar Probe, Solar Orbiter, STEREO A, and near-Earth spacecraft. The event was the second widespread SEP event detected in solar cycle 25, and it produced relativistic electrons and protons. It was associated with a long-lasting solar hard X-ray flare that showed multiple hard X-ray peaks over a duration of one hour. The event was further accompanied by a medium-fast coronal mass ejection (CME) with a speed of 880 km s -1 that drove a shock, an extreme ultraviolet wave, and long-lasting and complex radio burst activity that showed four distinct type III burst groups over a period of 40 min. We aim to understand the reason for the wide spread of elevated SEP intensities in the inner heliosphere as well as identify the underlying source regions of the observed energetic electrons and protons. We applied a comprehensive multi-spacecraft analysis of remote-sensing observations and in situ measurements of the energetic particles and interplanetary context to attribute the SEP observations at the different locations to the various potential source regions at the Sun. We used an ENLIL simulation to characterize the complex interplanetary state and its role in the energetic particle transport. The magnetic connection between each spacecraft and the Sun was determined using ballistic backmapping in combination with potential field source surface extrapolations in the lower corona. Using also a reconstruction of the coronal shock front, we then determined the times when the shock establishes magnetic connections with the different observers. Radio observations were used to characterize the directivity of the four main injection episodes, which were then employed in a 2D SEP transport simulation to test the importance of these different injection episodes. A comprehensive timing analysis of the inferred solar injection times of the SEPs observed at each spacecraft suggests different source processes being important for the electron and proton events. Comparison among the characteristics and timing of the potential particle sources, such as the CME-driven shock or the flare, suggests a stronger shock contribution for the proton event and a more likely flare-related source for the electron event. In contrast to earlier studies on widespread SEP events, we find that in this event an important ingredient for the wide SEP spread was the wide longitudinal range of about 110 o covered by distinct SEP injections, which is also supported by our SEP transport modeling.

sun↗

The effect of secondary electrons on the separate control of ion energy and flux in dual-frequency capacitively coupled radio frequency discharges

Dual-frequency capacitive discharges are used to separately control the mean ion energy, {epsilon}{sub ion}, and flux, {Gamma}{sub ion}, at the electrodes. We study the effect of secondary electrons on this separate control in argon discharges driven at 2+27 MHz at different pressures using Particle in Cell simulations. For secondary yield {gamma}{approx_equal}0, {Gamma}{sub ion} decreases as a function of the low frequency voltage amplitude due to the frequency coupling, while it increases at high {gamma} due to the effective multiplication of secondary electrons inside the sheaths. Therefore, separate control is strongly limited. {epsilon}{sub ion} increases with {gamma}, which might allow an in situ determination of {gamma}-coefficients.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pectin-associated mannans and xylans play distinct roles in cell-cell adhesion in pine and poplar wood

Wood particles of pine required longer treatments of acidic chlorite and dilute alkali to achieve similar proportions of cell separation as of poplar. Chemical extraction and enzymatic digestion studies indicated that rhamnogalacturonan-I (RG-I), mannan and xylan contribute to cell-cell adhesion in pine wood. Mannan associated with lignin in an acidic chlorite fraction and with xylan in a dilute alkali fraction. RG-I and xylan were extracted in both chlorite and dilute alkali in poplar. Scanning electron microscopy and a probe diffusion study using Fluorescence Recovery After Photobleaching showed that lignin, RG-I and mannan initiated cell separation at cell corners and dilute alkali extraction of xylan was required for complete cell separation in pine. Cell-cell separation increased enzymatic saccharification within 24 h by 2-fold in poplar and 3.4-fold in pine. Finally, our results inform a strategy to reduce particle size in woody biomass and provide insights into different molecular bases of cell-cell adhesion.

59 BASIC BIOLOGICAL SCIENCES↗

Integrable RCS as a Proposed Replacement for Fermilab Booster

Integrable optics is an innovation in particle accelerator design that potentially enables a greater betatron tune spread and damps collective instabilities. An integrable rapid-cycling synchrotron (RCS) would be an effective replacement for the Fermilab Booster, as part of a plan to reach multi-MW beam power at 120 GeV for the Fermilab high-energy neutrino program. We provide an example integrable lattice with features of a modern RCS - dispersion-free drifts, low momentum compaction factor, superperiodicity, chromaticity correction, bounded beta functions, and separate-function magnets.

43 PARTICLE ACCELERATORS↗

Measurement and interpretation of moments in inclusive semileptonic decays B{yields}X{sub c}l{sup -{nu}}

We present results for the moments of observed spectra in inclusive semileptonic B-meson decays to charm hadrons B{yields}X{sub c}l{sup -{nu}}. Moments of the hadronic-mass and the combined mass-and-energy spectra for different minimum electron or muon momenta between 0.8 and 1.9 GeV/c are obtained from a sample of 232x10{sup 6} {Upsilon}(4S){yields}BB events, collected with the BABAR detector at the PEP-II asymmetric-energy B-meson factory at SLAC. We also present a reevaluation of the moments of electron-energy spectra and partial decay fractions B(B{yields}X{sub c}e{sup -{nu}}) for minimum electron momenta between 0.6 and 1.5 GeV/c based on a sample of 51x10{sup 6} {Upsilon}(4S){yields}BB events. The measurements are used for the extraction of the total decay fraction, the Cabibbo-Kobayashi-Maskawa (CKM) matrix element |V{sub cb}|, the quark masses m{sub b} and m{sub c}, and four heavy-quark QCD parameters in the framework of a Heavy-Quark Expansion (HQE). We find B(B{yields}X{sub c}l{sup -{nu}})=(10.64{+-}0.17{+-}0.06)% and |V{sub cb}|=(42.05{+-}0.45{+-}0.70)x10{sup -3}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Measurement of the absolute branching fractions for D{sub s}{sup -}{yields}l{sup -}{nu}{sub l} and extraction of the decay constant f{sub D{sub s}}

The absolute branching fractions for the decays D{sub s}{sup -}{yields}l{sup -}{nu}{sub l} (l=e, {mu}, or {tau}) are measured using a data sample corresponding to an integrated luminosity of 521 fb{sup -1} collected at center-of-mass energies near 10.58 GeV with the BABAR detector at the PEP-II e{sup +}e{sup -} collider at SLAC. The number of D{sub s}{sup -} mesons is determined by reconstructing the recoiling system DKX{gamma} in events of the type e{sup +}e{sup -}{yields}DKXD{sub s}{sup *-}, where D{sub s}{sup *-}{yields}D{sub s}{sup -}{gamma} and X represents additional pions from fragmentation. The D{sub s}{sup -}{yields}l{sup -}{nu}{sub l} events are detected by full or partial reconstruction of the recoiling system DKX{gamma}l. The branching fraction measurements are combined to determine the D{sub s}{sup -} decay constant f{sub D{sub s}}=(258.6{+-}6.4{+-}7.5) MeV, where the first uncertainty is statistical and the second is systematic.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The status of open heavy flavor production at RHIC

We discuss the calculation of open heavy flavor cross sections at RHIC and describe how the semileptonic decays of charm and bottom quarks can be separated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗