Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface Modification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Hydrogenation and surface density changes in hydrocarbon films during erosion using Ar/H{sub 2} plasmas

We report interactions of low pressure Ar, H{sub 2}, and Ar/H{sub 2} mixture plasmas with a-C:H films. Surface evolution and erosion of a-C:H films were examined for ion energies up to 200 eV by rf biasing the substrates. Film surfaces were characterized using in situ ellipsometry, x-ray photoelectron spectroscopy, and atomic force microscopy. Multilayer models for steady-state modified surface layers are constructed using ellipsometric data and compared with results of molecular dynamics (MD) simulations and transport of ions in matter (TRIM) calculations. We find that Ar plasma causes a modified layer at the surface that is depleted of H atoms. The depth and degree of this modification is strongly depending on Ar ion energies. This depletion saturates quickly during plasma exposure (<1 s) and persists during steady-state erosion. We find that the thickness and density of the H-depleted layer are in good agreement with MD and TRIM simulations. The degree of surface densification decreases when small amounts of H{sub 2} are added to Ar plasmas. When more than 5% H{sub 2} is added to the plasma, long term loss in surface density is observed, indicating rehydrogenation and saturation of H in the film. As the H{sub 2} fraction increases, the near-surface atomic H increases and the ion composition bombarding the surface changes. This causes incorporation of H deeper into the a-C:H film. For a-C:H films exposed to pure H{sub 2} plasmas, H is introduced into the near-surface region to a depth of up to {approx}8 nm from the surface. As the rf bias is increased the ion energy transitions from solely chemical sputtering to one involving physical sputtering, causing the yield of C atoms from the surface to greatly increase. The increasing yield suppresses H incorporation/saturation and decreases the magnitude of the modified surface layer.

36 MATERIALS SCIENCE↗

Electrochemical Kinetics and X-ray Absorption Spectroscopic Investigations of Oxygen Reduction on Chalcogen-Modified Ruthenium Catalysts in Alkaline Media

The oxygen reduction reaction (ORR) in alkaline media has been investigated on chalcogen-modified ruthenium nanoparticles (Ru/C, Se/Ru/C, Se/RuMo/C, S/Ru/C, S/RuMo/C) synthesized in-house via aqueous routes. In acidic medium, it is well known that modification by a chalcogen prevents the oxidation of the underlying transition-metal (Ru) surface, thereby promoting direct molecular O{sub 2} adsorption on the Ru metal. On an unmodified Ru catalyst in alkaline media, the surface oxides on Ru mediate the 2e{sup -} reduction of molecular O{sub 2} to a stable peroxide anion (HO{sub 2}{sup -}) intermediate via an outer-sphere electron-transfer mechanism. This increases the activity of HO{sub 2}{sup -} near the electrode surface and decreases the overpotential for ORR by effectively carrying out the reduction of HO{sub 2}{sup -} to OH{sup -} at the oxide-free ruthenium metal site. An increase in ORR activity of Ru is observed by modification with a chalcogen; however, the increase is not as significant as observed in acidic media. Ternary additives, such as Mo, were found to significantly improve the stability of the chalcogen-modified catalysts. Detailed investigations of the ORR activity of this class of catalyst have been carried out in alkaline media along with comparisons to acidic media wherever necessary. A combination of electrochemical and X-ray absorption spectroscopic (EXAFS, XANES, {Delta}{mu}) studies has been performed in order to understand the structure/property relationships of these catalysts within the context of ORR in alkaline electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly stable multi-anchored magnetic nanoparticles for optical imaging within biofilms

Magnetic nanoparticles are the next tool in medical diagnoses and treatment in many different biomedical applications, including magnetic hyperthermia as alternative treatment for cancer and bacterial infections, as well as the disruption of biofilms. The colloidal stability of the magnetic nanoparticles in a biological environment is crucial for efficient delivery. A surface that can be easily modifiable can also improve the delivery and imaging properties of the magnetic nanoparticle by adding targeting and imaging moieties, providing a platform for additional modification. The strategy presented in this paper includes multiple nitroDOPA anchors for robust binding to the surface tied to the same polymer backbone as multiple poly(ethylene oxide) chains for steric stability. This approach provides biocompatibility and enhanced stability in fetal bovine serum (FBS) and phosphate buffer saline (PBS). As a proof of concept, these polymer-particles complexes were then modified with a near infrared dye and utilized in characterizing the integration of magnetic nanoparticles in biofilms. Finally, the work presented in this manuscript describes the synthesis and characterization of a nontoxic platform for the labeling of near IR-dyes for bioimaging.

36 MATERIALS SCIENCE↗

Development and Optimization of Modular Hybrid Plasma Reactor

INL developed a bench–scale, modular hybrid plasma system for gas-phase nanomaterials synthesis. The system was optimized for WO 3 nanoparticle production and scale-model projection to a 300 kW pilot system. During the course of technology development, many modifications were made to the system to resolve technical issues that surfaced and also to improve performance. All project tasks were completed except two optimization subtasks. Researchers were unable to complete these two subtasks, a four-hour and an eight-hour continuous powder production run at 1 lb/hr powder-feeding rate, due to major technical issues developed with the reactor system. The 4-hour run was attempted twice, and on both occasions, the run was terminated prematurely. The termination was due to (1) heavy material condensation on the modular electrodes, which led to system operational instability, and (2) pressure buildup in the reactor due to powder clogging of the exhaust gas and product transfer line. The modular electrode for the plasma system was significantly redesigned to address the material condensation problem on the electrodes. However, the cause for product powder clogging of the exhaust gas and product transfer line led to a pressure build up in the reactor that was undetected. Fabrication of the redesigned modular electrodes and additional components was completed near the end of the project life. However, insufficient resource was available to perform tests to evaluate the performance of the new modifications. More development work would be needed to resolve these problems prior to scaling.

36 MATERIALS SCIENCE↗

Multiwavelength digital holography with autocalibration of phase shifts and artificial wavelengths

A novel implementation of lensless multiwavelength digital holography with autocalibration of temporal phase shifts and artificial wavelength is presented. The algorithm we used to calculate the phase shifts was previously proposed [Opt. Lett.29 183 (2004)OPLEDP0146-959210.1364/OL.29.000183] and, to our knowledge, is now used for the first time in lensless holography. Because precise knowledge of the generated artificial wavelength is crucial for absolute measurement accuracy, a simple and efficient method to determine the artificial wavelength directly is presented. The calibration method is based on a simple modification of the experimental setup and needs just one additional image acquisition per wavelength. The results of shape measurement of a metallic test object with a rough surface and steep edges are shown and the measurement accuracy is discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On a new compactification of moduli of vector bundles on a surface. III: Functorial approach

A new compactification for the scheme of moduli for Gieseker-stable vector bundles with prescribed Hilbert polynomial on the smooth projective polarized surface (S,L) is constructed. We work over the field k=k-bar of characteristic zero. Families of locally free sheaves on the surface S are completed with locally free sheaves on schemes which are modifications of S. The Gieseker-Maruyama moduli space has a birational morphism onto the new moduli space. We propose the functor for families of pairs 'polarized scheme-vector bundle' with moduli space of such type. Bibliography: 16 titles.

97 MATHEMATICS AND COMPUTING↗

Ultraviolet Photoemission Spectroscopy and Kelvin Probe Measurements on Metal Halide Perovskites: Advantages and Pitfalls

In this essay, a case study is presented on the electronic structure of several metal halide perovskites (MHP) using Kelvin probe (KP)-based surface photovoltage (SPV) measurements and ultraviolet photoemission spectroscopy (UPS) to demonstrate the advantages, but also the pitfalls, of using these techniques to characterize the surfaces of these materials. The first part addresses the loss of halide species from perovskite surfaces upon supragap illumination in vacuum. This has the potential to cause both a long-term alteration of the sample work function and a modification of the KP tip during SPV measurements. If undetected, this leads to a misinterpretation of the MHP surface potential. The second part illustrates the difficulties in determining the valence band maximum (VBM) of MHP surfaces with UPS and stresses the importance of taking into account the low density of states at the VBM edge. Given this circumstance, specific care must be taken to eliminate measurement artifacts in order to ascertain the presence or absence of low densities of electronic gap states above the VBM. This essay also highlights issues such as film degradation, nonequilibrium situations (e.g., SPV), and satellite emissions, which occur during photoemission spectroscopy.

36 MATERIALS SCIENCE↗

Y-12 Groundwater Protection Program Groundwater And Surface Water Sampling And Analysis Plan For Calendar Year 2011

This plan provides a description of the groundwater and surface water quality monitoring activities planned for calendar year (CY) 2011 at the U.S. Department of Energy (DOE) Y-12 National Security Complex (Y-12) that will be managed by the Y-12 Groundwater Protection Program (GWPP). Groundwater and surface water monitoring performed by the GWPP during CY 2011 will be in accordance with requirements of DOE Order 540.1A and the following goals: (1) to protect the worker, the public, and the environment; (2) to maintain surveillance of existing and potential groundwater contamination sources; (3) to provide for the early detection of groundwater contamination and determine the quality of groundwater and surface water where contaminants are most likely to migrate beyond the Oak Ridge Reservation property line; (4) to identify and characterize long-term trends in groundwater quality at Y-12; and (5) to provide data to support decisions concerning the management and protection of groundwater resources. Groundwater and surface water monitoring during CY 2011 will be performed primarily in three hydrogeologic regimes at Y-12: the Bear Creek Hydrogeologic Regime (Bear Creek Regime), the Upper East Fork Poplar Creek Hydrogeologic Regime (East Fork Regime), and the Chestnut Ridge Hydrogeologic Regime (Chestnut Ridge Regime). The Bear Creek and East Fork regimes are located in Bear Creek Valley and the Chestnut Ridge Regime is located south of Y-12 (Figure A.1). Additional surface water monitoring will be performed north of Pine Ridge along the boundary of the Oak Ridge Reservation. Modifications to the CY 2011 monitoring program may be necessary during implementation. Changes in programmatic requirements may alter the analytes specified for selected monitoring wells or may add or remove wells from the planned monitoring network. All modifications to the monitoring program will be approved by the Y-12 GWPP manager and documented as addenda to this sampling and analysis plan. The following sections of this report provide details regarding the CY 2011 groundwater and surface water monitoring activities. Section 2 describes the monitoring locations in each regime and the processes used to select the sampling locations. A description of the field measurements and laboratory analytes is provided in Section 3. Sample collection methods and procedures are described in Section 4, and Section 5 lists the documents cited for more detailed operational and technical information. The narrative sections of the report reference several appendices. Figures (maps and diagrams) and tables (excluding data summary tables presented in the narrative sections) are in Appendix A and Appendix B, respectively. Groundwater Monitoring Schedules (when issued throughout CY 2011) will be inserted in Appendix C, and addenda to this plan (if issued) will be inserted in Appendix D. Laboratory requirements (bottle lists, holding times, etc.) are provided in Appendix E, and an approved Waste Management Plan is provided in Appendix F.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Thermal−Electrical Character of in Situ Synthesized Polyimide-Grafted Carbon Nanofiber Composites

Notwithstanding the success of polymer-carbon nanotube (CNT) nanocomposites, a solid understanding of the impact of external perturbations, including temperature and stress, on the electrical response, its reproducibility, and the subsequent relationship to the topology of the percolative morphology and molecular details of the CNT-CNT contact junction is not complete. Using an in situ synthesis approach, two series of polymide (CP2)-carbon nanofiber (CNF) composites are prepared with quantitatively (small-angle X-ray scattering) comparable CNF dispersions, but differing in the structure of the CNF-polymer interface. Amino-functionalized CNFs (FCNFs) enable direct formation of CP2 grafts onto the CNFs, whereas pristine CNFs (PCNFs) result in a relatively weak interface between the carbon nanofiber and CP2 matrix. In general, low-frequency ac impedance measurements are well described by the percolation bond model, yielding a percolation threshold below 1 vol % (0.24 and 0.68 vol % for PCNF-CP2 and FCNF-CP2, respectively). However, the design of the interface is determined to be crucial for controlling the electrical behavior in four substantial ways: magnitude of the limiting conductivity, linearity of the I-V response, magnitude and direction of temperature-dependent resistivity, and reproducibility of the absolute value of the resistivity with thermal cycling. These observations are consistent with a direct CNF-CNF contact limiting transport in the PCNF-CP2 system, where the CP2 grafts onto the FCNF from a dielectric layer, limiting transport within the FCNF-CP2 system. Furthermore, the grafted CP2 chains on the FCNF reduce local polymer dewetting at the CNF surfaces when the temperature exceeds the CP2 glass transition. This appears to stabilize the structure of the percolation network and associated conductivity. The general behavior of these interfacial extremes (pristine and fully functionalized CNFs) set important bounds on the design of interface modification for CNFs when the intended use is for electrical performance at elevated temperatures or under extreme current loads.

36 MATERIALS SCIENCE↗

Minimizing Grating Slope Errors in the IEX Monochromato at the Advanced Photon Source

The IEX beamline at the APS is currently in the commissioning phase. The energy resolution of the beamline was not meeting original specifications by several orders of magnitude. The monochromator, an in-focus VLS-PGM, is currently configured with a high and a medium-line-density grating. Experimental results indicated that both gratings were contributing to the poor energy resolution and this led to venting the monochromator to investigate. The initial suspicion was that a systematic error had occurred in the ruling process on the VLS gratings, but that proved to not be the case. Instead the problem was isolated to mechanical constraints used to mount the gratings into their respective side-cooled holders. Modifications were made to the holders to eliminate problematic constraints without compromising the rest of the design. Metrology performed on the gratings in the original and modified holders demonstrated a 20-fold improvement in the surface profile error which was consistent with finite element analysis performed in support of the modifications. Two gratings were successfully reinstalled and subsequent measurements with beam show a dramatic improvement in energy resolution.

Fisher, M. V.↗

Many-body dissipative particle dynamics simulation of liquid/vapor and liquid/solid interactions

The combination of short-range repulsive and long-range attractive forces in Many-body Dissipative Particle Dynamics (MDPD) is examined at a vapor/liquid and liquid/solid interface. Based on the radial distribution of the virial pressure in a drop at equilibrium, a systematic study is carried out to characterize the sensitivity of the surface tension coefficient with respect to the inter-particle interaction parameters. For the first time, this study highlights the approximately cubic dependence of the surface tension coefficient on the bulk density of the fluid. In capillary flow, MDPD solutions are shown to satisfy the condition on the wavelength of an axial disturbance leading to the pinch-off of a cylindrical liquid thread. Correctly, no pinch-off occurs below the cutoff wavelength. MDPD is augmented by a set of bell-shaped weight functions to model interaction with a solid wall. There, hydrophilic and hydrophobic behaviors, including the occurrence of slip in the latter, are reproduced using a modification in the weight function that avoids particle clustering. Finally, the dynamics of droplets entering an inverted Y-shaped fracture junction is correctly captured in simulations parameterized by the Bond number, proving the flexibility of MDPD in modeling interface-dominated flows.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Time-Resolved Imaging of Material Response Following Laser-Induced Breakdown in the Bulk and Surface of Fused Silica

Optical components within high energy laser systems are susceptible to laser-induced material modification when the breakdown threshold is exceeded or damage is initiated by pre-existing impurities or defects. These modifications are the result of exposure to extreme conditions involving the generation of high temperatures and pressures and occur on a volumetric scale of the order of a few cubic microns. The response of the material following localized energy deposition, including the timeline of events and the individual processes involved during this timeline, is still largely unknown. In this work, we investigate the events taking place during the entire timeline in both bulk and surface damage in fused silica using a set of time-resolved microscopy systems. These microscope systems offer up to 1 micron spatial resolution when imaging static or dynamic effects, allowing for imaging of the entire process with adequate temporal and spatial resolution. These systems incorporate various pump-probe geometries designed to optimize the sensitivity for detecting individual aspects of the process such as the propagation of shock waves, near-surface material motion, the speed of ejecta, and material transformations. The experimental results indicate that the material response can be separated into distinct phases, some terminating within a few tens of nanoseconds but some extending up to about 100 microseconds. Overall the results demonstrate that the final characteristics of the modified region depend on the material response to the energy deposition and not on the laser parameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Large bandgap observed on the surfaces of EuZn 2 As 2 single crystals

EuM 2 As 2 (M = Zn, Cd, In, Sn etc.) is an excellent material system for studying magnetism-tuned topological properties. However, discrepancies exist between experimental data and theoretical calculations regarding the bulk and surface bandgaps. In this work, cleaved EuZn 2 As 2 crystals are studied using scanning tunneling microscopy/spectroscopy and density functional theory calculations. Triangular-shaped defect-induced modifications in the local density of states help distinguish between Eu-terminated and AsZn-terminated surfaces. While large bandgaps (~1.5 eV at 77 K) are observed on both pristine surfaces, the bandgap size is found to be highly sensitive to local heterogeneity, tending to decrease. By combining experimental observations with theoretical simulations, we conclude that the reduced bandgap in heterogeneous regions arises from Zn vacancies and/or substitution by As atoms, both impacting greater in the Eu surface electronic properties than those in the AsZn surface. This demonstrates the intimate relationship between the electronic structure and magnetism in EuZn 2 As 2 .

interfaces↗

Experimental Study of Spontaneous Emission in Bragg Multiple- Quantum-Well Structures with InAs Single-Layer Quantum Wells

The time-resolved photoluminescence of a Bragg structure formed by InAs single-layer quantum wells in a GaAs matrix is investigated experimentally. The comparison of photoluminescence spectra recorded from the edge and the surface of the sample indicates that Bragg ordering of the quantum wells leads to substantial modification of the spectra, in particular, to the appearance of additional modes. The spectrum recorded at the edge of the sample features a single line corresponding to the exciton ground state. In the spectrum recorded at the surface, an additional line whose frequency and propagation angle correspond to the Bragg condition for quantum wells, appears at high excitation levels. The calculation of the modal Purcell factor explains the fact that spontaneous emission is enhanced only for specific propagation angles and frequencies, rather than for all angles and frequencies satisfying the Bragg condition.

36 MATERIALS SCIENCE↗

Stability Enhancement and Microstructural Modification of Ni-Rich Cathodes via Halide Doping

In this study, elemental doping is an effective strategy to modify surface and bulk chemistry in NMC cathode materials. By adding small amounts of lithium halide salts during the calcination process, the Ni-rich NMC811 cathode is doped with Br, Cl, or F halogens. The dopant type has a significant impact on the lithiation process and heavily influences the final cathode porosity and surface morphology. Utilizing a variety of electrochemical, surface, and bulk characterization techniques, it is demonstrated that an initial content of 5 mol % LiBr or LiCl in the lithium source is effective in improving capacity retention while also providing excellent rate performance. The improvements are attributed to a substantial increase in specific surface area, the formation of a stable cathode electrolyte interface (CEI) layer, and suppressed surface reconstruction. In addition, the particle microstructure is better equipped to handle cyclic volume changes with increased values of critical crack lengths. Overall, it is demonstrated that anion doping via the addition of lithium halide salts is a facile approach toward Ni-rich NMC modification for enhanced cathode performance.

25 ENERGY STORAGE↗

Fundamental study of laser-induced surface damage in silica optics

The objective of this study is to develop a fundamental understanding of defect-assisted laser-induced optical absorption and its accompanying material modification in wide band-gap optical materials. A suite of sensitive high resolution optical techniques and an advanced computational modeling methodology has been developed and employed to clarify these processes in the near-surface region of fused silica. This capability will be broadly applicable to a wide class of problems involving optically-induced material modification. As a result of this project, much progress was made towards developing a fundamental understanding of defect-assisted laser-induced optical absorption and optical in silica. In particular, this work provided new insights into the dynamics of a damage event and produced the first non-destructive diagnostic with the promise of being able to predict which surface flaws in silica have high damage susceptibility.

36 MATERIALS SCIENCE↗

Mineralogical transformations in polymetallic nodules and the change of Ni, Cu and Co crystal-chemistry upon burial in sediments

Polymetallic nodules from the Clarion and Clipperton Zone of the equatorial Pacific Ocean were studied using X-ray diffraction, X-ray absorption, Fourier-transformed infrared spectroscopy and transmission electron microscopy. Here, this study includes nodules found at the sediment surface as well as subsurface (14–16 cm sediment depth) and deeply buried (530–985 cm sediment depth) nodules. The surface and subsurface nodules are currently under oxic conditions whereas the deeply buried nodules are under suboxic conditions. Surface nodules consist mainly of turbostratic phyllomanganates (7 Å and 10 Å vernadite and Fe-vernadite); todorokite is a minor phase, if present at all. In contrast, subsurface and especially deeply buried nodules predominantly consist of todorokite, which increases in abundance with depth in the sediment. Thus, upon burial of nodules within the shallow sediment, phyllomanganates transform to todorokite, probably through the combined action of time and change in the ambient chemical conditions. Nodules from deeper sediment depth (>500 cm) consist primarily of todorokite and additionally show signs of dissolution. The transformation of phyllomanganates to todorokite and their further dissolution upon nodule burial under suboxic conditions induces modifications in the crystal-chemistry of Ni, Co, and Cu. In surface nodules, Ni and Co are incorporated in the octahedral sheets of phyllomanganates, whereas Cu mainly is located at the edges of those phyllomanganate sheets. In buried nodules Cu and to a lesser extent Ni are incorporated in todorokite by forming outer-sphere complexes within the tunnels. However, Ni is predominantly incorporated within the octahedra of the newly formed todorokite structure. Co is also enriched in the octahedra of todorokite as a result of dissolution of hydrogenetic vernadite and re-incorporation in the more stable Mn-phase formed during the diagenetic transformation. Co enrichment under suboxic conditions after burial within the sediments is noteworthy since Co in surface nodules is characteristic for oxic conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metal-organic and zeolite imidazolate frameworks (MOFs and ZIFs) for highly selective separations

Metal-organic and zeolite imidazolate frameworks (MOFs and ZIFs) have been investigated for the realization as separation media with high selectivity. These structures are held together with strong bonds, making them architecturally, chemically, and thermally stable. Therefore, employing well designed building units, it is possible to discover promising materials for gas and vapor separation. This grant was focused on the study of MOFs and ZIFs with these specific objectives: (i) to develop a strategy for producing MOFs and ZIFs that combine high surface areas with active sites for their use in gas adsorption and separation of small organic compounds, (ii) to introduce active sites in the framework by a post-synthetic modification and metalation of MOFs and ZIFs, and (iii) to design and synthesize MOFs with extremely high surface areas and large pore volumes to accommodate large amounts of guest molecules. By the systematic study, this effort demonstrated how to introduce active functional groups in the frameworks, and this is also the origin of a new strategy, which is termed isoreticular functionalization and metalation. However, a large pore volume is still a prerequisite feature. One of the solutions to overcome this challenge is an isoreticular expansion of a MOF's structure. With triangular organic linker and square building units, we demonstrated that MOF-399 has a unit cell volume 17 times larger than that of the first reported material isoreticular to it, and it has the highest porosity (94%) and lowest density (0.126 g cm -3 ) of any MOF reported to date. MOFs are not just low density materials; the guest-free form of MOF-210 demonstrates an ultrahigh porosity, whose BET surface area was estimated to be 6240 m 2 g -1 by N 2 adsorption measurements.

36 MATERIALS SCIENCE↗