Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

A new method for the preparation of a Fe{sub 3}O{sub 4}/graphene hybrid material and its applications in electromagnetic wave absorption

Graphical abstract: A microwave-assisted solvothermal process was used to prepare Fe{sub 3}O{sub 4} nanoparticles/graphene hybrids, which could be applied as an electromagnetic (EM) radiation absorbent. The absorber, composed of 20 wt% Fe{sub 3}O{sub 4}/graphene–epoxy, exhibited a dual-frequency reflection characteristic covering the C and Ku bands with maximum reflection losses of less than −20 dB at thicknesses of 4 and 5 mm. - Highlights: • Fe{sub 3}O{sub 4}/graphene composites were prepared by a microwave-assisted solvothermal route. • Uniform loading of Fe{sub 3}O{sub 4} nanoparticles on graphene was obtained. • The products as-synthesized show great promise as a microwave absorption material. • Synergistic effects of Fe{sub 3}O{sub 4} and graphene caused improved absorption efficiency. • The Fe{sub 3}O{sub 4}/graphene product possessed a dual-frequency reflection characteristic. - Abstract: A rapid, simple, and inexpensive process combining a microwave-assisted technique and a solvothermal method has been developed using graphene sheets and FeCl{sub 3}·6H{sub 2}O as the reactant to prepare graphene/Fe{sub 3}O{sub 4} nanoparticle hybrids, which can be applied as an electromagnetic radiation absorbent. The experimental factors (i.e., composition ratio, microwave power, and irradiation time) on the products’ characteristics were examined. Under optimal conditions, the morphological analysis revealed that the graphene sheet was homogeneously covered with Fe{sub 3}O{sub 4} nanoparticles (∼50 nm). The electromagnetic parameters of the composites made from 20 wt% Fe{sub 3}O{sub 4}/graphene–epoxy were measured by a vector network analyzer. It was found that the 4- and 5 mm-thick composites could attain a reflection loss below −20 dB in the dual-ranges of 4–8 and 12–18 GHz.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Designing Piezoelectric Films for Micro Electromechanical Systems

Piezoelectric thin films are of increasing interest in low-voltage micro electromechanical systems for sensing, actuation, and energy harvesting. They also serve as model systems to study fundamental behavior in piezoelectrics. Next-generation technologies such as ultrasound pill cameras, flexible ultrasound arrays, and energy harvesting systems for unattended wireless sensors will all benefit from improvements in the piezoelectric properties of the films. This paper describes tailoring the composition, microstructure, orientation of thin films, and substrate choice to optimize the response. It is shown that increases in the grain size of lead-based perovskite films from 75 to 300 nm results in 40 and 20% increases in the permittivity and piezoelectric coefficients, respectively. This is accompanied by an increase in the nonlinearity in the response. Band excitation piezoresponse force microscopy was used to interrogate the nonlinearity locally. It was found that chemical solution-derived PbZr(0.52)Ti(0.48)O(3) thin films show clusters of larger nonlinear response embedded in a more weakly nonlinear matrix. The scale of the clusters significantly exceeds that of the grain size, suggesting that collective motion of many domain walls contributes to the observed Rayleigh behavior in these films. Finally, it is shown that it is possible to increase the energy-harvesting figure of merit through appropriate materials choice, strong imprint, and composite connectivity patterns.

Trolier-McKinstry, Susan↗

Optimization of Elastically Tailored Tow-Placed Plates with Holes

Elastic stiffness tailoring of laminated composite panels by allowing the fibers to curve within the plane of the laminate is a design concept that has been demonstrated to be both beneficial and practical. The objective of the present paper is to demonstrate the effectiveness of stiffness tailoring through the use of curvilinear fibers to reduce stress concentrations around the hole and improve the load carrying capability of panels. Preliminary panel designs that are to be manufactured and tested were determined through design studies for flat plates without holes under axial compression using an optimization program. These candidate designs were then analyzed with finite element models that accurately reflect the test conditions and geometries in order to decide upon the final designs for manufacture and testing. An advanced tow-placement machine is used to manufacture the test panels with varying fiber orientation angles. A total of six large panels measuring three feet by six feet, each of which is used to produce four specimens with or without holes, are fabricated. The panels were machined into specimens with holes and tested at NASA Langley Research Center. Buckling response and failure of panels without holes and with two different hole dimensions are presented. Buckling and failure loads of tow-steered specimens are significantly greater than the buckling and failure loads of traditional straight-fiber specimens.

Jegley, Dawn C.↗

POSTOP: Postbuckled open-stiffener optimum panels-theory and capability

The computer program POSTOP was developed to serve as an aid in the analysis and sizing of stiffened composite panels that are loaded in the postbuckling regime. A comprehensive set of analysis routines was coupled to a widely used optimization program to produce this sizing code. POSTOP is intended for the preliminary design of metal or composite panels with open-section stiffeners, subjected to multiple combined biaxial compression (or tension), shear and normal pressure load cases. Longitudinal compression, however, is assumed to be the dominant loading. Temperature, initial bow eccentricity and load eccentricity effects are included. The panel geometry is assumed to be repetitive over several bays in the longitudinal (stiffener) direction as well as in the transverse direction. Analytical routines are included to compute panel stiffnesses, strains, local and panel buckling loads, and skin/stiffener interface stresses. The resulting program is applicable to stiffened panels as commonly used in fuselage, wing, or empennage structures. The analysis procedures and rationale for the assumptions used therein are described in detail.

Dickson, J. N.↗

Estimation of 3D Woven Design Sensitivities Using a Rapid Multiscale Analysis Technique

Highly-refined finite element models of three-dimension (3D) woven composite systems currently require excessive computational demands that limit their use in sensitivity analysis, uncertainty quantification, and optimization. An alternative analysis methodology was developed using the NASA Multiscale Analysis Tool (NASMAT) where multiscale models of a 3D woven composite (including inter-tow matrix voids and constituent failure) can be completed on a single central processing unit(CPU)on the order of ~30 s. To develop inputs and validation data for the NASMAT model, coupon and acid-digesting testing and x-ray computed tomography were performed. The NASMAT inputs were parameterized using a set of 25 input variables and distributions. These inputs were randomly sampled to generate a total of 100,000 NASMAT analyses that could be used to understand the influence of different material and geometric properties on the warp and weft-direction stiffness and strength. These analyses (including pre/post-processing) were performed in less than eight hours on a 120 CPU cluster. The computational efficiency of the NASMAT model enabled a sensitivity analysis to be performed, and dominant input variables were able to be identified. Key results were consistent with theoretical and experimental observations for the specific 3D woven system studied in this work.

NASMAT↗

Estimation of 3D Woven Design Sensitivities Using a Rapid Multiscale Analysis Technique

Highly-refined finite element models of three-dimension (3D) woven composite systems currently require excessive computational demands that limit their use in sensitivity analysis, uncertainty quantification, and optimization. An alternative analysis methodology was developed using the NASA Multiscale Analysis Tool (NASMAT) where multiscale models of a 3D woven composite (including inter-tow matrix voids and constituent failure) can be completed on a single central processing unit (CPU) on the order of ~30s. To develop inputs and validation data for the NASMAT model, coupon and acid-digesting testing and x-ray computed tomography were performed. The NASMAT inputs were parameterized using a set of 25 input variables and distributions. These inputs were randomly sampled to generate a total of 100,000 NASMAT analyses that could be used to understand the influence of different material and geometric properties on the warp and weft-direction stiffness and strength. These analyses (including pre/post-processing) were performed in less than eight hours on a 120 CPU cluster. The computational efficiency of the NASMAT model enabled a sensitivity analysis to be performed, and dominant input variables were able to be identified. Key results were consistent with theoretical and experimental observations for the specific 3D woven system studied in this work.

NASMAT↗

Remarkable enhancement in thermal conductivity of stainless-steel leveraging metal composite via laser powder bed fusion: 316L-Cu composite

This work aimed to significantly enhance the thermal conductivity of the SS matrix by fabricating a metal composite SS-Cu system utilizing a laser powder bed fusion process. The impact of process parameters on the microstructure of SS-Cu samples is investigated. Here, the processing and post-processing factors that influence the effective thermal conductivity of the metal composite SS-Cu system are discussed. Then, the effective thermal conductivity and mechanical properties of the SS-Cu composite are measured at room temperature and operating temperature of 300 °C. The optimized laser powder bed fusion parameters led to low Marangoni convection, high cooling rate, greater macro-segregation, and higher thermal conductivity values albeit at the cost of ductility in SS-Cu metal composite likely due to the presence of the unmelted powder particles. As-printed SS-60 vol % Cu and annealed SS-60 vol % Cu had 2.5X and 6.6X thermal conductivity enhancement, respectively. During annealing, phase separation, partial melting of Cu, and formation of a continuous network of Cu surrounding SS play a key role in enhancing the thermal conductivity of the SS-Cu metal composite structure.

36 MATERIALS SCIENCE↗

Blended-Wing-Body (BWB) Fuselage Structural Design for Weight Reduction

Structural analysis and design of efficient pressurized fuselage configurations for the advanced Blended-Wing-Body (BWB) flight vehicle is a challenging problem. Unlike a conventional cylindrical pressurized fuselage, stress level in a box type BWB fuselage is an order of magnitude higher, because internal pressure primarily results in bending stress instead of skin-membrane stress. In addition, resulting deformation of aerodynamic surface could significantly affect performance advantages provided by lifting body. The pressurized composite conformal multi-lobe tanks of X-33 type space vehicle also suffered from similar problem. In the earlier BWB design studies, Vaulted Ribbed Shell (VLRS), Flat Ribbed Shell (FRS); Vaulted shell Honeycomb Core (VLHC) and Flat sandwich shell Honeycomb Core (FLHC) concepts were studied. The flat and vaulted ribbed shell concepts were found most efficient. In a recent study, a set of composite sandwich panel and cross-ribbed panel were analyzed. Optimal values of rib and skin thickness, rib spacing, and panel depth were obtained for minimal weight under stress and buckling constraints. In addition, a set of efficient multi-bubble fuselage (MBF) configuration concept was developed. The special geometric configuration of this concept allows for balancing internal cabin pressure load efficiently, through membrane stress in inner-stiffened shell and inter-cabin walls, while the outer-ribbed shell prevents buckling due to external resultant compressive loads. The initial results from these approximate finite element analyses indicate progressively lower maximum stresses and deflections compared to the earlier study. However, a relative comparison of the FEM weight per unit floor area of the segment unit indicates that the unit weights are still relatively higher that the conventional B777 type cylindrical or A380 type elliptic fuselage design. Due to the manufacturing concern associated with multi-bubble fuselage, a Y braced box-type fuselage alternative with special resin-film injected (RFI) stitched carbon composite with foam-core was designed by Boeing under a NASA research contract for the 480 passenger version. It is shown that this configuration can be improved to a modified multi-bubble fuselage which has better stress distribution, for same material and dimension.

Mukhopadhyay, V.↗

Power factor improvement in hydrothermally synthesized Bi{sub 2-x}Sb{sub x}Te{sub 3} (x=1.5) - carbon sphere composites

We report fabrication of compacted Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composites by adding 1 wt% of carbon spheres in the hydrothermal synthesis. The processing parameter of sintering temperature is investigated in order to optimize the thermoelectric power factor of pressed Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composites. As a result, we find that the composite sintered at 360 Degree-Sign C shows the best power factor performance among the composites and has a largest power factor of 15.4 {mu}W/cm K{sup 2} at 205 K and 13.5 {mu}W/cm K{sup 2} at 290 K. When compared with the samples without addition of carbon sphere in the hydrothermal synthesis, the composites sintered at 340 Degree-Sign C and 360 Degree-Sign C both surpass the largest power factor of 12.1 {mu}W/cm K{sup 2} at 280 K and 11.9 {mu}W/cm K{sup 2} at 290 K for the 340 Degree-Sign C-sintered counterpart. - Graphical abstract: Compacted Bi{sub 0.5}Sb{sub 1.5}Te{sub 3-{delta}} composites obtained by adding 1 wt% of carbon spheres in the hydrothermal synthesis. The composites sintered at 340 Degree-Sign C and 360 Degree-Sign C both surpass the largest power factor of 12.1 {mu}W/cm K{sup 2} at 280 K and 11.9 {mu}W/cm K{sup 2} at 290 K for the 340 Degree-Sign C-sintered counterpart. Highlights: Black-Right-Pointing-Pointer Fabrication of Bi{sub 0.5}Sb{sub 1.5}Te{sub 3-{delta}} composites. Black-Right-Pointing-Pointer Addition of 1 wt% carbon spheres in the hydrothermal synthesis. Black-Right-Pointing-Pointer Investigation of sintering temperature using encapsulating-and-sintering techniques. Black-Right-Pointing-Pointer 360 Degree-Sign C-sintered composite showing the largest power factor of 15.4 {mu}W/cm K{sup 2} at 205 K. Black-Right-Pointing-Pointer 10-60% improvement over the counterpart without adding carbon spheres.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal spin-transfer torque in magnetic tunnel junctions (invited)

The thermal spin-transfer torque (TSTT) is an effect to switch the magnetic free layer in a magnetic tunnel junction by a temperature gradient only. We present ab initio calculations of the TSTT. In particular, we discuss the influence of magnetic layer composition by considering Fe{sub x}Co{sub 1–x} alloys. Further, we compare the TSTT to the bias voltage driven STT and discuss the requirements for a possible thermal switching. For example, only for very thin barriers of 3 monolayers MgO, a thermal switching is imaginable. However, even for such a thin barrier, the TSTT is still too small for switching at the moment and further optimization is needed. In particular, the TSTT strongly depends on the composition of the ferromagnetic layer. In our current study, it turns out that at the chosen thickness of the ferromagnetic layer, pure Fe gives the highest thermal spin-transfer torque.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Integrated analysis and applications

An overview is presented of current research activities which, in a broad context, are focused on the development and verification of integrated structural analysis and optimal design capabilities for advanced aerospace propulsion and power systems. The overview encompasses a variety of subject areas including: (1) composite materials; (2) advanced structural analysis; (3) constitutive modeling; (4) computational simulation; (5) probabilistic analysis; and (6) multidisciplinary optimization. Typical results are presented which illustrate the benefit and utility of the emerging technologies as applied to propulsion and power system structures.

Hopkins, Dale A.↗

Processing of phase change materials by fused deposition modeling: Toward efficient thermal energy storage designs

We report that recently, several efforts have emerged that employ additive manufacturing techniques to integrate phase change material (PCM) thermal energy storage into geometrically complex designs for advanced thermal management. In this work, we contribute to this emerging research by reporting on the production of a composite nylon-based filament for fused deposition modeling incorporating encapsulated PCMs for 3D printing heat sink geometries. Microencapsulated PCM (MEPCM) with a 6 degrees C transition temperature was selected as the material for thermal energy storage. This transition temperature was selected due to its suitability to provide thermal energy storage to target air-conditioning applications in buildings. In an attempt to improve the thermal conductivity of the composite, fine boron nitride fillers were added, although the effect on improvement was found to be negligible in the overall composite mixture. The nylon-MEPCM ratio in the filaments was optimized, and filaments containing up to 40 wt% MEPCM were successfully synthesized, which were found optimal for 3D printing complex heat sink and other geometries. Thermal and mechanical properties of the filaments were characterized, including latent heat of fusion, thermal conductivity, phase change temperature, tensile strength, and more. Thermal infrared imaging of heat sink geometries printed using the MEPCM filaments undergoing thermal discharging was also conducted. This work presents the most promising result to date in the open literature for a 3D-printed PCM composite in the combination of size, energy density, and geometric complexity of printed parts.

25 ENERGY STORAGE↗

Evaluating tantalum oxide stoichiometry and oxidation states for optimal memristor performance

Tantalum oxide has shown promising electrical switching characteristics for memristor devices. Consequently, a number of reports have investigated the electrical behavior of TaO{sub x} thin films. Some effort has been made to characterize the composition of the TaO{sub x} films and it is known that there must be an optimal stoichiometry of TaO{sub x} where forming and switching behavior are optimized. However, many previous reports lack details on the methodology used for identifying the chemistry of the films. X-ray photoelectron spectroscopy has been the most commonly used technique; however, peak fitting routines vary widely among reports and a native surface oxide of Ta{sub 2}O{sub 5} often confounds the analysis. In this report a series of large area TaO{sub x} films were deposited via sputtering with controlled O{sub 2} partial pressures in the sputtering gas, resulting in tunable oxide compositions. Spectra from numerous samples from each wafer spanning a range of oxide stoichiometries were used to develop a highly constrained peak fitting routine. This procedure allowed for the composition of the TaO{sub x} films to be identified with greater detail than elemental ratios alone. Additionally, the peak fitting routine was used to evaluate uniformity of deposition across individual wafers. The appearance of a greater contribution of Ta{sup 4+} oxidation states in the oxygen starved films are believed to relate to films with optimal forming characteristics.

36 MATERIALS SCIENCE↗

BNL Irradiation Damage Studies of the Metal Matrix Composite Mo-GR Considered for High Luminosity LHC Collimator Upgrade

A comprehensive experimental/analytical effort on the resilience of Mo-GR metal matrix composite to high energy proton beam irradiation combined with elevated temperatures has been undertaken at BNL on behalf of the CERN LHC Collimation effort as part of an effort to identify novel materials that will exhibit optimal performance in the high luminosity LHC upgrade. While the Mo-Gr composite was one of the four (4) different materials or composites (Mo, Glidcop, Cu-CD and Mo-Gr) that constituted the High Luminosity LHC collimation material campaign, this report focuses solely on Mo-GR with some reference to its constituents Mo and graphite (graphite studied in previous research or irradiation campaigns along with the carbonfiber composites). The multi-faceted study on Mo-GR (one of several different alloys and matrices) performed at BNL included the following stages: Irradiation damage phase using the 200 MeV proton beams of the BNL Linac and the BLIP target beamline. Specifically, Mo-GR samples encapsulated under vacuum in special capsules were exposed to direct protons as part of a multi-capsule, multi-material irradiation array. The long-term irradiation of ~8 weeks resulted in an accumulated fluence at the Mo-GR of ~10 21 p/cm 2 . The irradiation was conducted in two sessions (RUN 2013 and RUN 2014 of the BLIP operations in tandem with isotope production). Irradiation damage experiments using spallation neutrons at the BLIP beamline generated by 118 MeV protons that interact with and are stopped by an array of isotope producing targets. The Mo-GR capsule combined the effects of short-term proton irradiation and the effects of the mixed irradiating spectrum. Spallation-induced irradiation of Mo-GR at sub-zero temperatures utilizing the mixed field generated by spallation of 28 MeV protons of the BN Tandem on Mo targets Gamma spectrum analysis of the heavily irradiated Mo-Gr to enable the correlation of predicted isotope profile from Mo-Gr by transport codes and therefore the utilization of the validated transport code in other aspects of the damage induced on Mo-Gr by irradiation.

43 PARTICLE ACCELERATORS↗

SUMMARY OF 2010 DOE EM INTERNATIONAL PROGRAM STUDIES OF WASTE GLASS MELT RATE ENHANCEMENT

A collaborative study has been established under the U.S. Department of Energy (DOE) Office of Environmental Management International Program between the Savannah River National Laboratory (SRNL) and the V. G. Khlopin Radium Institute (KRI) in St. Petersburg, Russia, to investigate potential improvements in melt rate via chemical additions to the glass frit. Researchers at KRI suggested a methodology for selecting frit additives based on empirical coefficients for optimization of glass melting available in the Russian literature. Using these coefficients, KRI identified B{sub 2}O{sub 3}, CuO, and MnO as frit additives that were likely to improve melt rate without having adverse effects on crystallization of the glass or its chemical durability. The results of the melt rate testing in the SMK melter showed that the slurry feed rate (used as a gauge of melt rate) could be significantly increased when MnO or CuO were added to Frit 550 with the SMR-2 sludge. The feed rates increased by about 27% when MnO was added to the frit and by about 26% when CuO was added to the frit, as compared to earlier results for Frit 550 alone. The impact of adding additional B{sub 2}O{sub 3} to the frit was minor when added with CuO. The additional B{sub 2}O{sub 3} showed a more significant, 39% improvement in melt rate when added with MnO. The additional B{sub 2}O{sub 3} also reduced the viscosity of the glasses during pouring. Samples of the glasses from the melt rate testing characterized at SRNL showed that there were no significant impacts on crystallization of the glasses. All of the glasses had very good chemical durability. Chemical composition measurements showed that the frit additives were present in concentrations below the targeted values in some of the glasses. Therefore, it is possible that higher concentrations of these additives may further improve melt rate, although the impacts of higher concentrations of these components on crystallization and durability would need to be determined. Overall, the results show an excellent potential for these additives to significantly improve waste throughput for DOE vitrification facilities. A complete report from KRI is included as an appendix to this document.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of a Computer Architecture to Support the Optical Plume Anomaly Detection (OPAD) System

The NASA OPAD spectrometer system relies heavily on extensive software which repetitively extracts spectral information from the engine plume and reports the amounts of metals which are present in the plume. The development of this software is at a sufficiently advanced stage where it can be used in actual engine tests to provide valuable data on engine operation and health. This activity will continue and, in addition, the OPAD system is planned to be used in flight aboard space vehicles. The two implementations, test-stand and in-flight, may have some differing requirements. For example, the data stored during a test-stand experiment are much more extensive than in the in-flight case. In both cases though, the majority of the requirements are similar. New data from the spectrograph is generated at a rate of once every 0.5 sec or faster. All processing must be completed within this period of time to maintain real-time performance. Every 0.5 sec, the OPAD system must report the amounts of specific metals within the engine plume, given the spectral data. At present, the software in the OPAD system performs this function by solving the inverse problem. It uses powerful physics-based computational models (the SPECTRA code), which receive amounts of metals as inputs to produce the spectral data that would have been observed, had the same metal amounts been present in the engine plume. During the experiment, for every spectrum that is observed, an initial approximation is performed using neural networks to establish an initial metal composition which approximates as accurately as possible the real one. Then, using optimization techniques, the SPECTRA code is repetitively used to produce a fit to the data, by adjusting the metal input amounts until the produced spectrum matches the observed one to within a given level of tolerance. This iterative solution to the original problem of determining the metal composition in the plume requires a relatively long period of time to execute the software in a modern single-processor workstation, and therefore real-time operation is currently not possible. A different number of iterations may be required to perform spectral data fitting per spectral sample. Yet, the OPAD system must be designed to maintain real-time performance in all cases. Although faster single-processor workstations are available for execution of the fitting and SPECTRA software, this option is unattractive due to the excessive cost associated with very fast workstations and also due to the fact that such hardware is not easily expandable to accommodate future versions of the software which may require more processing power. Initial research has already demonstrated that the OPAD software can take advantage of a parallel computer architecture to achieve the necessary speedup. Current work has improved the software by converting it into a form which is easily parallelizable. Timing experiments have been performed to establish the computational complexity and execution speed of major components of the software. This work provides the foundation of future work which will create a fully parallel version of the software executing in a shared-memory multiprocessor system.

Katsinis, Constantine↗

Aging Optimization of Aluminum-Lithium Alloy C458 for Application to Cryotank Structures

This viewgraph report presents an examination of the fracture toughness of aluminum-lithium alloy C458 for use in cryotank structures. Topics cover include: cryogenics, alloy composition, strengthing precipitates in C458, cryogenic fracture toughness improvements, design of experiments for measuring aging optimization of C458 plate and effects of aging of properties of C458 plate.

Sova, B. J.↗