Search NASA⌕ Search

SEARCH · Search NASA

Results for “etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Effect of Different Cutting Techniques on the Surface Morphology and Composition of Niobium

The surface morphology and chemical purity of superconducting radio frequency (SRF) niobium cavities are very important for proper accelerator operation. Typically on the order of 120 micrometers of niobium (Nb) is removed from cavities to remove damage done during the forming of Nb sheets and cavities. A study was done to find the effect of cutting or finishing Nb with a band saw, diamond saw, electrical discharge machining (EDM) wire, garnet water jet, sheer, and mill. Surface contamination of the samples was measured before and after buffered chemical polish (BCP) by secondary ion mass spectroscopy (SIMS), energy dispersive spectroscopy (EDS), and by measuring relative resistivity ratios (RRRs). Surface morphology was examined with a digital microscope, a surface profilometer and scanning electron microscope (SEM). It was found that all techniques altered the top 3-5 micrometers of the Nb. It was also found by SIMS that the water jet technique introduced the most hydrogen and oxygen to the Nb in the first 2.5 micrometers of the sample. The EDM wire cutting technique introduced the least amount of hydrogen to the Nb. After 5 micrometers were etched away by BCP on the various samples, no contaminants were found except on the water jet cut samples. Even after 20 micrometers of Nb removal silica could be seen on the surface with EDS. The water jet produced the roughest surface with 50-100 micrometer deep pits made from embedded garnet particles. It was found that the garnet water jet damages the surface to the point where even the typical 120 micrometers of BCP etching may not remove all the defects created.

43 PARTICLE ACCELERATORS↗

Experimental study of spatial nonuniformities in 100 MHz capacitively coupled plasma using optical probe

Plasma spatial nonuniformities in the 100 MHz rf driven capacitively coupled reactor used for reactive ion etching of 300 mm substrates were experimentally studied using a linear scanning optical emission spectroscopy probe. Radial profiles of plasma emission intensity were measured both in argon and fluorocarbon-containing gas mixtures in the pressure interval of 10-80 mTorr and the rf power range of 500-1250 W. It was demonstrated that the plasma emission profiles strongly depend on the working gas composition and pressure. The profiles have a bell-like shape at pressures about 10 mTorr for all gases. As the pressure increases, the profile shape becomes more complex with the central and peripheral peaks, and the amplitudes of the peaks strongly depend on the working gas composition. It is suggested that the emission profiles show plasma spatial nonuniformities that can influence the etching rate profiles obtained with such systems. According to the existing theoretical models, the most probable reasons for these plasma nonuniformities are charged particle radial diffusion at low pressures (about 10 mTorr), as well as the standing wave and skin and edge effects at higher pressures. Using the experimental emission profiles, the working conditions have been found that allow one to achieve the most uniform plasma for discharges in argon and fluorocarbon-containing gas mixtures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Precise and high-speed control of partial pressures of multiple gas species in plasma process chamber using pulse-controlled gas injection

Multiprocesses in a single plasma process chamber with high throughput require precise, sequential, high-speed alteration of partial pressures of multiple gas species. A conventional gas-distribution system cannot realize this because the system seriously overshoots gas pressure immediately following valve operation. Furthermore, chamber volume and conductance of gas piping between the system and chamber should both be considered because they delay the stabilizing time of gas pressure. Therefore, the authors proposed a new gas-distribution system without overshoot by controlling gas flow rate based on pressure measurement, as well as a method of pulse-controlled gas injection immediately following valve operation. Time variation of measured partial pressure agrees well with a calculation based on an equivalent-circuit model that represents the chamber and gas piping between the system and chamber. Using pulse-controlled gas injection, the stabilizing time can be reduced drastically to 0.6 s for HBr added to pure Ar plasma, and 0.7 s for O{sub 2} added to Ar/HBr plasma; without the pulse control, the stabilizing times are 3 and 7 s, respectively. In the O{sub 2} addition case, rapid stabilization can be achieved during the period of line/space pattern etching of poly-Si on a thin SiO{sub 2} film. This occurs without anomalous etching of the underlying SiO{sub 2} film or the Si substrate near the sidewall, thus obtaining a wide process margin with high throughput.

36 MATERIALS SCIENCE↗

Auger electron spectroscopy study of reactor walls in transition from an O{sub 2} to a Cl{sub 2} plasma

In plasma etching processes, the reactor wall conditions can change over time due to a number of intentional and unintentional reasons, leading to a variability in the radical number densities in the plasma, caused by changes in the probabilities for reactions such as recombination at the walls. This leads to loss of reproducibility in the etching process. Here the authors isolated one such effect in which the feed gas was changed in the absence of a substrate. The transient surface composition of an anodized aluminum surface was determined for inductively coupled plasmas as the gas was switched from Cl{sub 2} to O{sub 2} and vice versa. The study was carried out with the spinning wall method and Auger electron spectroscopy. When the surface was first conditioned in an O{sub 2} plasma and then exposed to Cl{sub 2} plasmas, a rapid uptake of Cl was found in the first tens of seconds, followed by a slow approach to a steady-state value within {approx}5 min of plasma exposure. Conversely, when the surface was exposed to a Cl{sub 2} plasma for a long time and then switched to an O{sub 2} plasma, the anodized aluminum surface underwent a rapid dechlorination in the first few seconds and then a slow approach to steady state over {approx}3 min. Throughout these treatments, the coverages of Si (from erosion of the quartz discharge tube) and O were nearly constant.

36 MATERIALS SCIENCE↗

Chemical Effect of Dry and Wet Cleaning of the Ru Protective Layer of the Extreme ultraviolet (EUV) Lithography Reflector

The authors report the chemical influence of cleaning of the Ru capping layer on the extreme ultraviolet (EUV) reflector surface. The cleaning of EUV reflector to remove the contamination particles has two requirements: to prevent corrosion and etching of the reflector surface and to maintain the reflectivity functionality of the reflector after the corrosive cleaning processes. Two main approaches for EUV reflector cleaning, wet chemical treatments [sulfuric acid and hydrogen peroxide mixture (SPM), ozonated water, and ozonated hydrogen peroxide] and dry cleaning (oxygen plasma and UV/ozone treatment), were tested. The changes in surface morphology and roughness were characterized using scanning electron microscopy and atomic force microscopy, while the surface etching and change of oxidation states were probed with x-ray photoelectron spectroscopy. Significant surface oxidation of the Ru capping layer was observed after oxygen plasma and UV/ozone treatment, while the oxidation is unnoticeable after SPM treatment. Based on these surface studies, the authors found that SPM treatment exhibits the minimal corrosive interactions with Ru capping layer. They address the molecular mechanism of corrosive gas and liquid-phase chemical interaction with the surface of Ru capping layer on the EUV reflector.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface loss rates of H and Cl radicals in an inductively coupled plasma etcher derived from time-resolved electron density and optical emission measurements

A study is undertaken of the loss kinetics of H and Cl atoms in an inductively coupled plasma (ICP) reactor used for the etching of III-V semiconductor materials. A time-resolved optical emission spectroscopy technique, also referred to as pulsed induced fluorescence (PIF), has been combined with time-resolved microwave hairpin probe measurements of the electron density in a pulsed Cl{sub 2}/H{sub 2}-based discharge for this purpose. The surface loss rate of H, k{sub w}{sup H}, was measured in H{sub 2} plasma and was found to lie in the 125-500 s{sup -1} range ({gamma}{sub H} surface recombination coefficient of {approx}0.006-0.023), depending on the reactor walls conditioning. The PIF technique was then evaluated for the derivation of k{sub w}{sup Cl}, and {gamma}{sub Cl} in Cl{sub 2}-based plasmas. In contrast to H{sub 2} plasma, significant variations in the electron density may occur over the millisecond time scale corresponding to Cl{sub 2} dissociation at the rising edge of the plasma pulse. By comparing the temporal evolution of the electron density and the Ar-line intensity curves with 10% of Ar added in the discharge, the authors show that a time-resolved actinometry procedure using Ar as an actinometer is valid at low to moderate ICP powers to estimate the Cl loss rate. They measured a Cl loss rate of {approx}125-200 s{sup -1} (0.03{<=}{gamma}{sub Cl}{<=}0.06) at 150 W ICP power for a reactor state close to etching conditions. The Cl surface loss rate was also estimated for high ICP power (800 W) following the same procedure, giving a value of {approx}130-150 s{sup -1} ({gamma}{sub Cl}{approx}0.04), which is close to that measured at 150 W ICP power.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Orientation-dependent ion beam sputtering at normal incidence conditions in FeSiAl alloy

The authors have performed Ar+ broad ion beam sputtering of a polycrystalline Fe-Si-Al alloy at normal incidence at energies varying from 6 to 10 keV. Sputtering results in the formation of etch pits, which can be classified in three shapes: triangular, rectangular, and square. As each grain of individual orientation exhibits a certain type of pattern, the etch pits were correlated with the crystal orientations by electron backscattered diffraction technique.

36 MATERIALS SCIENCE↗

Glancing angle deposition of Ge nanorod arrays on Si patterned substrates

A periodic arrangement of Ge nanorods on a Si(111) substrate was realized by glancing angle deposition (GLAD) onto honeycomb-like arranged Au hillocks formed using a self-assembled monolayer of polystyrene nanospheres as an evaporation mask. Additionally, a honeycomb-like arrangement of Au dots was used as an etch mask in a reactive ion beam etching process for pattern transfer procedure. Resulting honeycomb patterns consisting of Si hillocks within the Si(111) substrates were utilized to deposit Ge nanorods. Effective morphological variations in shape and dimension of GLAD-grown nanorods on honeycomb-like patterned substrates with both Au dot and Si dot arrays are strongly influenced by interseed distances, seed heights, and consequently shadowing lengths. For a large pattern period, it was observed that the usual triangular shape of the nanorod changed to a hexagonal shape as an effect of additional particle flux that reached the growing nanorod from the direction of second and third-nearest neighbors due to inadequate shadowing lengths and increased interseed condensation.

36 MATERIALS SCIENCE↗

Damage by radicals and photons during plasma cleaning of porous low-k SiOCH. I. Ar/O{sub 2} and He/H{sub 2} plasmas

Porous dielectric materials offer lower capacitances that reduce RC time delays in integrated circuits. Typical porous low dielectric (low-k) materials include SiOCH-silicon dioxide with carbon groups, principally -CH{sub 3}, lining the pores. Fluorocarbon plasmas are often used to etch such low-k materials. These processes leave a fluorocarbon polymer on the SiOCH surface that must be removed, often with oxygen or hydrogen containing plasmas. Pores open to the surface and that are internally connected provide pathways for reactive species to enter into the porous network and produce damage. For example, during cleaning using O{sub 2} containing plasmas, reactions of O atoms with -CH{sub 3} groups can increase the k-value by removing C atoms. Vacuum ultraviolet (VUV) photons produced by the plasma and that penetrate into the material can scission -Si-CH{sub 3} bonds and accelerate the removal of -CH{sub 3} groups. This paper reports on results from a computational investigation of Ar/O{sub 2} and He/H{sub 2} plasma cleaning of porous SiOCH when including the effects of VUV photons. The authors found that He/H{sub 2} plasmas are able to clean CF{sub x} polymers deposited during etching while producing milder damage to underlying -CH{sub 3} sites compared to O{sub 2} plasmas due to the lower reactivity of H atoms and the shorter penetration distance of photons produced in He/H{sub 2} plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cl atom recombination on silicon oxy-chloride layers deposited on chamber walls in chlorine-oxygen plasmas

Chlorine atom recombination coefficients were measured on silicon oxy-chloride surfaces deposited in a chlorine inductively coupled plasma (ICP) with varying oxygen concentrations, using the spinning wall technique. A small cylinder embedded in the walls of the plasma reactor chamber was rapidly rotated, repetitively exposing its surface to the plasma chamber and a differentially pumped analysis chamber housing a quadruple mass spectrometer for line-of-sight desorbing species detection, or an Auger electron spectrometer for in situ surface analysis. The spinning wall frequency was varied from 800 to 30 000 rpm resulting in a detection time, t (the time a point on the surface takes to rotate from plasma chamber to the position facing the mass or Auger spectrometer), of {approx}1-40 ms. Desorbing Cl{sub 2}, due to Langmuir-Hinshelwood (LH) Cl atom recombination on the reactor wall surfaces, was detected by the mass spectrometer and also by a pressure rise in one of the differentially pumped chambers. LH Cl recombination coefficients were calculated by extrapolating time-resolved desorption decay curves to t = 0. A silicon-covered electrode immersed in the plasma was either powered at 13 MHz, creating a dc bias of -119 V, or allowed to electrically float with no bias power. After long exposure to a Cl{sub 2} ICP without substrate bias, slow etching of the Si wafer coats the chamber and spinning wall surfaces with an Si-chloride layer with a relatively small amount of oxygen (due to a slow erosion of the quartz discharge tube) with a stoichiometry of Si:O:Cl = 1:0.38:0.38. On this low-oxygen-coverage surface, any Cl{sub 2} desorption after LH recombination of Cl was below the detection limit. Adding 5% O{sub 2} to the Cl{sub 2} feed gas stopped etching of the Si wafer (with no rf bias) and increased the oxygen content of the wall deposits, while decreasing the Cl content (Si:O:Cl = 1:1.09:0.08). Cl{sub 2} desorption was detectable for Cl recombination on the spinning wall surface coated with this layer, and a recombination probability of {gamma}{sub Cl} = 0.03 was obtained. After this surface was conditioned with a pure oxygen plasma for {approx}60 min, {gamma}{sub Cl} increased to 0.044 and the surface layer was slightly enriched in oxygen fraction (Si:O:Cl = 1:1.09:0.04). This behavior is attributed to a mechanism whereby Cl LH recombination occurs mainly on chlorinated oxygen sites on the silicon oxy-chloride surface, because of the weak Cl-O bond compared to the Cl-Si bond.

36 MATERIALS SCIENCE↗

Modeling of inductively coupled plasma Ar/Cl{sub 2}/N{sub 2} plasma discharge: Effect of N{sub 2} on the plasma properties

A global kinetic model of Cl{sub 2}/Ar/N{sub 2} plasma discharge has been developed, which allows calculation of the densities and fluxes of all neutral and charged species considered in the reaction scheme, as well as the electron temperature, as a function of the operating conditions. In this work, the results from the global model are first compared to the calculations given by other models. Our simulation results are focused on the effect of nitrogen adding to the Cl{sub 2}/Ar plasma mixture, which impacts both neutral and charged species transport phenomena. The N{sub 2} percentage is varied to the detriment of Cl{sub 2} by keeping the total flow rates of Cl{sub 2} and N{sub 2} constant. In order to better understand the impact of N{sub 2} addition to the Cl{sub 2}/Ar gas mixture, the authors analyzed the output plasma parameters calculated from the model for different N{sub 2} flow rate percentages. Indeed, the simulation results show a decrease in electron density and an increase in electron temperature with increasing percentage of N{sub 2}. Particular attention is paid to the analysis of electronegativity, Cl{sub 2} and N{sub 2} dissociation, and positive ion to neutral flux ratio evolution by varying percentage of N{sub 2}. Such parameters have a direct effect on the etching anisotropy of the materials during the etching process.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-resolution chemical patterns from negative tone resists for the integration of extreme ultraviolet patterns of metal-oxide resists with directed self-assembly of block copolymers

Extreme ultraviolet (EUV) lithography faces significant challenges in designing suitable resist materials that can provide adequate precision, while maintaining economically viable throughput. These challenges in resist materials have led to printing failures and high roughness in EUV patterns, compromising the performance of semiconductor devices. Integrating directed self-assembly (DSA) of block copolymers (BCPs) with EUV lithography offers a promising solution because, while the BCPs register to the EUV-defined chemical guiding pattern, the thermodynamically determined structures of the BCPs automatically rectify defects and roughness in the EUV pattern. Despite the superior resolution of metal-oxide EUV resists (MORs), their application to DSA is limited by the difficulty in converting them into chemical patterns that allow effective transfer of the rectified patterns of DSA films into inorganic materials. To address this challenge, this study introduces a novel strategy for fabricating chemical patterns using hydrogen silsesquioxane (HSQ), a high-resolution negative tone inorganic resist, as a model system for MORs. Initially, a sacrificial Cr pattern is generated from HSQ patterns via reactive ion etching. The sacrificial Cr pattern is converted into a chemical pattern by first grafting a water-soluble polyethylene oxide brush onto the substrate, then wet etching the Cr, and finally grafting nonpolar polystyrene brushes. Assembling polystyrene-block-poly(methyl methacrylate) on these patterns results in structures oriented and registered with the underlying pattern, achieving 24 nm full-pitch resolutions. In conclusion, this approach has the potential to integrate MOR patterns into the DSA process, thereby enabling the generation of high-quality sub-10 nm patterns with high-χ BCPs.

Atomic force microscopy↗

Determination of laser damage initiation probability and growth on fused silica scratches

Current methods for the manufacture of optical components inevitably leaves a variety of sub-surface imperfections including scratches of varying lengths and widths on even the finest finishes. It has recently been determined that these finishing imperfections are responsible for the majority of laser-induced damage for fluences typically used in ICF class lasers. We have developed methods of engineering subscale parts with a distribution of scratches mimicking those found on full scale fused silica parts. This much higher density of scratches provides a platform to measure low damage initiation probabilities sufficient to describe damage on large scale optics. In this work, damage probability per unit scratch length was characterized as a function of initial scratch width and post fabrication processing including acid-based etch mitigation processes. The susceptibility of damage initiation density along scratches was found to be strongly affected by the post etching material removal and initial scratch width. We have developed an automated processing procedure to document the damage initiations per width and per length of theses scratches. We show here how these tools can be employed to provide predictions of the performance of full size optics in laser systems operating at 351 nm. In addition we use these tools to measure the growth rate of a damage site initiated along a scratch and compare this to the growth measured on an isolated damage site.

42 ENGINEERING↗

Influence of Processing Techniques on the Surface Microstructure of V{sub 85}Ni{sub 15} Membrane Alloy

Vanadium-based alloys with a BCC structure are considered to be an alternative to palladium alloys for hydrogen purification. Since the performance of membranes is influenced by not only their bulk characteristics but also their surface condition, we have investigated the effect of different surface preparation techniques (abrasive grinding and polishing, electrolytic polishing, and ion etching) on the surface microstructure of V{sub 85}Ni{sub 15} membrane alloy using X-ray photoelectron spectroscopy. After electrolytic polishing and ion etching, we observed an increase in the percentages of vanadium and nickel metals in the surface layer of the alloy in comparison with its state after abrasive polishing. Such changes are expected to be favorable for an increase in the rate of hydrogen dissociation and recombination on the surface of the membrane material, eventually improving hydrogen transport efficiency.

36 MATERIALS SCIENCE↗

X-ray diffraction study of the morphology and structure of pulse-anodized porous Si multilayers

Porous Si layers, obtained by pulsed electrochemical etching of n-Si(001) substrates (resistivity 0.01 {Omega} cm) in a 1: 1 mixture of hydrofluoric acid and ethanol, have been investigated by high-resolution X-ray diffraction and electron microscopy. The average structural parameters of the layers grown (thickness, strain, porosity, pore size) are determined. It is found that pulsed anodic oxidation leads to a decrease in the average strain of layers. It is established that, at frequencies up to 1 Hz, anodic oxidation makes obtaining porous silicon multilayers with layer thicknesses of 20-300 nm containing Si nanocrystallites possible. It is shown that X-ray diffuse scattering from pores yields information about their ordering and can be used to monitor the processes of electrochemical etching used to form porous layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical properties of iron-passivated nanoporous silicon

The intensity of photoluminescence from nanoporous silicon layers produced by electrochemical etching in an aqueous-alcoholic HF solution in the presence of iron ions increases and properties of these layers are stabilized. The optimal FeCl{sub 3} concentration in the etching solution has been found. The interaction of iron ions with the silicon surface and the nature and possible products of reactions involving oxygen and hydrogen have been studied.

36 MATERIALS SCIENCE↗

Defect-related luminescence in silicon p{sup +}–n junctions

Ultra-shallow p{sup +}–n junctions fabricated by the silicon planar technology based on the short-time nonequilibrium diffusion of boron from the gas phase into n-Si (100) substrates upon their preliminary oxidation and the opening of windows in SiO{sub 2} by electron lithography and reactive ion etching are examined. The electroand photoluminescence spectra measured in the study demonstrate emission in the range 1–1.6 µm, which is indicative of the presence of a high concentration of defects that probably appear as a result of the amorphizing effect of ions in the etching stage.

36 MATERIALS SCIENCE↗

Investigation of the fabrication processes of AlGaN/AlN/GaN HEMTs with in situ Si{sub 3}N{sub 4} passivation

The optimum mode of the in situ plasma-chemical etching of a Si{sub 3}N{sub 4} passivating layer in C{sub 3}F{sub 8}/O{sub 2} medium is chosen for the case of fabricating AlGaN/AlN/GaN HEMTs. It is found that a bias of 40–50 V at a high-frequency electrode provides anisotropic etching of the insulator through a resist mask and introduces no appreciable radiation-induced defects upon overetching of the insulator films in the region of gate-metallization formation. To estimate the effect of in situ Si{sub 3}N{sub 4} growth together with the heterostructure in one process on the AlGaN/AlN/GaN HEMT characteristics, transistors with gates without the insulator and with gates through Si{sub 3}N{sub 4} slits are fabricated. The highest drain current of the AlGaN/AlN/GaN HEMT at 0 V at the gate is shown to be 1.5 times higher in the presence of Si{sub 3}N{sub 4} than without it.

36 MATERIALS SCIENCE↗