Search NASA⌕ Search

SEARCH · Search NASA

Results for “interlayer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Ductilisation of tungsten (W): Tungsten laminated composites

Here we elucidate the mechanisms of plastic deformation and fracture of tungsten laminated composites. Furthermore our results suggest that the mechanical response of the laminates is governed by the plastic deformation of the tungsten plies. In most cases, the impact of the interlayer is of secondary importance.

36 MATERIALS SCIENCE↗

Exploring the elastic and electronic properties of chromium molybdenum diboride alloys

We perform first-principles calculations to study the structural, mechanical, thermal, electronic, and magnetic properties of Cr 1-x Mo x B 2 for x = 0.25, 0.33, 0.50, 0.67 and 0.75. Based on structural search methods, we determine the ground-state structure for each concentration. The ternaries are either monoclinic (x = 0.25, 0.75) or trigonal (x = 0.33, 0.50, 0.67). The calculated mechanical properties reveal that the strength of Cr 1-x Mo x B 2 is maximized for x = 0.50. Cr 0.5 Mo 0.5 B 2 exhibits excellent mechanical properties (B = 298 GPa, Y = 558 GPa, G = 235 Gpa, ν = 0.19, H v =27 GPa), surpassing those of β-MoB 2 at a lower cost. All of these ternaries are hard alloys with Vickers hardness greater than 24 GPa. Chemical bonding analysis demonstrates that the strength of the new compounds is related to the alternating planar and buckled B-B layers, as well as the strong TM-B bonds. Finally, the enhanced strength of Cr 0.5 Mo 0.5 B 2 is a consequence of the high density of strong interlayer Cr-Mo metallic bonds around the Fermi level.

36 MATERIALS SCIENCE↗

Pressure dependent magnetic properties on bulk CrBr 3 single crystals

The van der Waals class of materials offer an approach to two-dimensional magnetism as their spin fluctuations can be tuned upon exfoliation of layers. Moreover, it has recently been shown that spin-lattice coupling and long-range magnetic ordering can be modified with pressure in van der Waals materials. In this work, the magnetic properties of quasi two-dimensional CrBr 3 are reported applying hydrostatic pressure. The application of pressure up to 0.844 GPa shows a 1.77% decrease in saturation magnetization with a decrease in the Curie temperature from 33.05 to 30.41 K. Density functional theory calculations with pressure up to 1 GPa show a reduction in volume and interplanar distance as pressure increases. To further understand the magnetic properties with applied pressure, the magnetocrystalline anisotropy energy (MAE) and exchange coupling parameter (J) are calculated. There is small decrease in MAE and the first nearest neighbor interaction (J 1 ) (U = 2.7 eV and J = 0.7 eV) is increasing with respect to increasing pressure. Overall, CrBr 3 displays ferromagnetic interlayer coupling and the calculated exchange coupling and MAE parameters match well with the observations from the experimental work.

36 MATERIALS SCIENCE↗

Exchange bias and interface-related effects in two-dimensional van der Waals magnetic heterostructures: Open questions and perspectives

The exchange bias (EB) effect is known as a fundamentally and technologically important magnetic property of a magnetic bilayer film. It is manifested as a horizontal shift in a magnetic hysteresis loop of a film subject to cooling in the presence of a magnetic field. The EB effect in van der Waals (vdW) heterostructures offers a novel approach for tuning the magnetic properties of the newly discovered single-layer magnets, as well as adds a new impetus to magnetic vdW heterostructures. Indeed, intriguing EB effects have recently been reported in a variety of low-dimensional vdW magnetic systems ranging from a weakly interlayer-coupled vdW magnet (e.g., Fe 3 GeTe 2 ) to a bilayer composed of two different magnetic vdW materials (e.g., Fe 3 GeTe 2 /CrCl 3 , Fe 3 GeTe 2 /FePS 3 , Fe 3 GeTe 2 /MnPS 3 , Fe 3 GeTe 2 /CrSe, Fe 3 GeTe 2 /CrOCl, Fe 3 GeTe 2 /CoPc, Fe 5 GeTe 2 /FePS 3 ), to bilayers of two different vdW defective magnets (e.g., VSe 2 /MoS 2 ), or to metallic ferromagnet/vdW defective magnet interfaces (e.g., Fe/MoS 2 ). Despite their huge potential in spintronic device applications, the physical origins of the observed EB effects have remained elusive to researchers. Here, we present here a critical review of the EB effect and associated phenomena such as magnetic proximity (MP) in various vdW heterostructure systems and propose approaches to addressing some of the emerging fundamental questions.

2D magnets↗

Solid phase characterization and transformation of illite mineral with gas-phase ammonia treatment

In situ remediation applications of ammonia (NH 3 ) gas have potential for sequestration of subsurface contamination. Ammonia gas injections initially increase the pore water pH leading to mineral dissolution followed by formation of secondary precipitates as the pH is neutralized. However, there is a lack of understanding of fundamental alteration processes due to NH 3 treatment. In these batch studies, phyllosilicate minerals (illite and montmorillonite) were exposed to NH 3 gas with subsequent aeration to simulate in situ remediation. Following treatments, solids were characterized using a variety of techniques, including X-ray diffraction, N 2 adsorption-desorption analysis for surface area, Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), and microscopy methods to investigate physicochemical transformations. The results of this study indicate that, at high pH, the clays are altered as observed by differences in morphology and particle size via microscopy. However, the two clays interact differently with NH 3 . While montmorillonite interlayers collapsed due to intercalation, illite layers were unaffected as confirmed by FTIR analysis. Further, structural changes in silicate ([SiO 4 ] n- ) and aluminol (Al-OH) groups were identified by NMR and FTIR. This research showed that mineral alteration processes occur during and after NH 3 gas treatment which may be used to remove radionuclides from the aqueous phase through sorption, co-precipitation, and coating with secondary phyllosilicate alteration products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of the iodate sorption mechanism by CoAl LDH through experiments and ab initio molecular dynamics simulations

Radioiodine released during the nuclear-fuel cycle constitutes a persistent radiological hazard. In this study, the IO 3 – uptake mechanism of CoAl LDH was resolved by combining pH-controlled sorption experiments, synchrotron XAFS, and DFT-based AIMD simulations. At pH close to 6, approximately 90% of IO 3 – was removed, and the equilibrium distribution coefficient reached about 1.7 × 10 4 mL g –1 . EXAFS analysis indicated an average iodine–oxygen bond length of 1.81 Å and a coordination number near 3, with the fit R-factor equal to 0.002. The simulations faithfully reproduced the experimental spectrum and revealed transient proton hopping events that generated metastable I–O–H species inside the interlayer, thereby confirming nitrate-to-iodate exchange as the controlling capture pathway. Atomic density profiles and radial distribution functions further showed that IO 3 – adopt an end-on orientation perpendicular to the hydroxide sheets, while water molecules mediate proton migration without disturbing the host lattice. In conclusion, the integrated experimental–computational evidence demonstrates that CoAl LDH can rapidly and selectively sequester IO 3 – under near-neutral conditions, offering atomic scale guidance for the rational engineering of layered sorbents for advanced radioactive-waste treatment.

Kang, Jaehyuk [Jeju National Univ. (Korea, Republi↗

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗

Micromagnetic simulations with periodic boundary conditions: Hard-soft nanocomposites

Here, we developed a micromagnetic method for modeling magnetic systems with periodic boundary conditions along an arbitrary number of dimensions. The main feature is an adaptation of the Ewald summation technique for evaluation of long-range dipolar interactions. The method was applied to investigate the hysteresis process in hard-soft magnetic nanocomposites with various geometries. The dependence of the results on different micromagnetic parameters was studied. We found that for layered structures with an out-of-plane hard phase easy axis the hysteretic properties are very sensitive to the strength of the interlayer exchange coupling, as long as the spontaneous magnetization for the hard phase is significantly smaller than for the soft phase. The origin of this behavior was discussed. Additionally, we investigated the soft phase size optimizing the energy product of hard-soft nanocomposites.

36 MATERIALS SCIENCE↗

The influence of diameter on the magnetic saturation in Fe 84 Cu 16 /MgO [0 0 1] multilayered islands

The saturation field of circular islands, consisting of Fe 84 Cu 16 [/MgO] 9 Fe 84 Cu 16 multilayers, increases with decreasing diameter of the islands. When the diameter of the islands is below 450 nm the field induced changes are dominated by a coherent rotation of the moment of the Fe 84 Cu 16 layers. For diameters of 2 μm and larger, a signature of domain nucleation and evolution is observed. Here, the changes in the saturation field with diameter of the islands are ascribed to the interplay between interlayer exchange coupling, stray field coupling at the edges and the crystalline anisotropy of the Fe 84 Cu 16 layers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Functional properties of Yttrium Iron Garnett thin films on graphene-coated Gd 3 Ga 5 O 12 for remote epitaxial transfer

Remote epitaxial growth via a graphene interlayer and subsequent mechanical exfoliation of a free-standing membrane is a recently developed technique used to transfer complex oxide thin films onto non-native substrates to form heterogeneously integrated structures for various device applications. One such oxide is Yttrium Iron Garnet (YIG), a material of choice for a wide range of magnetoelectric and spintronic devices owing to its strong magnetic properties and low microwave losses. YIG is predominantly grown on lattice matched Gadolinium Gallium Garnet (GGG) substrates, but by utilizing the remote epitaxy technique, high quality YIG films can be transferred from GGG onto another substrate such as piezoelectric Lithium Niobate (LN). Mechanical strain coupling between the layers and magnetostrictive nature of YIG would allow for the investigation of the interplay in YIG/LN structures leading to the design of novel frequency agile magneto-acoustic devices. In this study functional properties of a YIG film grown using PLD on graphene-coated GGG substrate were investigated and compared to traditional YIG on GGG. Both materials were characterized in terms of crystal structure, surface morphology, FMR and Gilbert damping, and Raman and XAS spectroscopy. Further, it was found that YIG on graphene-coated GGG exhibits significantly higher microwave losses than standard YIG on GGG (FMR linewidth 30.9 vs 2.1 Oe at 10 GHz, and Gilbert damping coefficient 15.4x10 -4 vs 3.4x10 -4 respectively), which was attributed to increased concentration of Fe 2+ cations in YIG/Graphene/GGG. While the damping is higher in these studied films compared to YIG grown directly on GGG, the resulting properties are still very favorable compared to many other competing materials which can be grown without the need for lattice matched substrates, such as metallic ferromagnets.

36 MATERIALS SCIENCE↗

Multimodal analysis and characterization of the boehmite layer formed on AA6061 before and after alkaline etching

Low-enriched uranium (LEU) alloyed with 10% Mo (U-10Mo) is being considered as a promising alternative to oxide-based dispersion fuel with high-enriched uranium for use in research reactors. The configuration of this proposed LEU monolithic LEU fuel plate consists of a U-10Mo plate-type fuel foil with a 25 µm zirconium interlayer barrier clad with an aluminum alloy (AA6061). In certain research reactors, the clad AA6061 is coated with a boehmite layer to prevent corrosion. The boehmite layer has a high-pH passivation range, which makes it resistant to oxidation. Boehmite is usually formed on the AA6061 surface by autoclave processing. Before the boehmite layer is added, the surface of the AA6061 is cleaned using techniques such as polishing and wet etching. In this study, we use multimodal analysis to examine how pretreatment of AA6061 using polishing followed by alkaline etching affects the chemical composition of the boehmite layer. X-ray photoelectron microscopy (XPS), transmission electron microscopy (TEM), and x-ray diffraction (XRD) were used to study the chemical changes in the boehmite layer caused by alkaline etching pretreatment. XPS provides quantitative analysis for the Al:O ratio as well as oxidation states present on the surface, which suggests slight oxidation of the boehmite surface after alkaline etching of the AA6061 surface. We further explored this suggested oxidation of the boehmite surface using high-resolution transmission electron microscopy with selected area electron diffraction (SAED) and grazing incidence x-ray diffraction (GI-XRD), which suggested only a small amount of aluminum oxide at the surface. The multimodal analysis and imaging yielded new insights for optimizing boehmite growth on AA6061 for research reactors.

36 MATERIALS SCIENCE↗

Identification of Silver and Palladium in Irradiated TRISO Coated Particles of the AGR-1 Experiment

Evidence of the release of certain metallic fission product through intact tristructural isotropic (TRISO) particles has been seen for decades around the world, as well as in the recent AGR-1 experiment at Idaho National Laboratory (INL). However, understanding the basic mechanism of transport is still lacking. This understanding is important because the TRISO coating is part of the high temperature gas reactor functional containment and critical for the safety strategy for licensing purposes. Our approach to identify fission products in irradiated AGR-1 TRISO fuel using scanning transmission electron microscopy (STEM), Electron Energy Loss Spectroscopy (EELS) and Energy Filtered TEM (EFTEM), has led to first-of-a-kind data at the nano-scale indicating the presence of silver at triple points and grain boundaries of the SiC layer in the TRISO particle. Cadmium was also found in the triple junctions. In this initial study, the silver was only identified in SiC grain boundaries and triple points on the edge of the SiC-IPyC interface up to a depth of approximately 0.5 um. Palladium was identified as the main constituent of micron-sized precipitates present at the SiC grain boundaries. Additionally spherical nano-sized palladium rich precipitates were found inside the SiC grains. These nano-sized Pd precipitates were distributed up to a depth of 5 um away from the SiC-IPyC interlayer. No silver was found in the center of the micron-sized fission product precipitates using these techniques, although silver was found on the outer edge of one of the Pd-U-Si containing precipitates which was facing the IPyC layer. Only Pd-U containing precipitates were identified in the IPyC layer and no silver was identified in the IPyC layer. The identification of silver alongside the grain boundaries and the findings of Pd alongside grain boundaries as well as inside the grains, provide significant knowledge for understanding silver and palladium transport in TIRSO fuel, which has been the topic of international research for the past forty years. Additionally the usefulness of the advanced electron microscopic techniques for TRISO coated particle research is demonstrated in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrothermal corrosion of silicon carbide joints without radiation

In this paper, hydrothermal corrosion of four types of the silicon carbide (SiC) to SiC plate joints were investigated under pressurized water reactor and boiling water reactor relevant chemical conditions without irradiation. The joints were formed by metal diffusion bonding using molybdenum or titanium interlayer, reaction sintering using Ti—Si—C system, and SiC nanopowder sintering. Most of the joints withstood the corrosion tests for five weeks. The recession of the SiC substrates was limited. Based on the recession of the bonding layers, it was concluded that all the joints except for the molybdenum diffusion bond are promising under the reducing environments without radiation. Finally, the SiC nanopowder sintered joint was the most corrosion tolerant under the oxidizing environment among the four joints.

36 MATERIALS SCIENCE↗

Irradiation resistance of silicon carbide joint at light water reactor–relevant temperature

We fabricated and irradiated monolithic silicon carbide (SiC) to SiC plate joints with neutrons at 270–310 °C to 8.7 dpa for SiC. The joining methods included solid state diffusion bonding using titanium and molybdenum interlayers, SiC nanopowder sintering, reaction sintering with a Ti-Si-C system, and hybrid processing of polymer pyrolysis and chemical vapor infiltration (CVI). All the irradiated joints exhibited apparent shear strength of more than 84 MPa on average. Significant irradiation-induced cracking was found in the bonding layers of the Ti and Mo diffusion bonds and Ti-Si-C reaction sintered bond. Furthermore, the SiC-based bonding layers of the SiC nanopowder sintered and hybrid polymer pyrolysis and CVI joints all showed stable microstructure following the irradiation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Impacts of annealing treatment on the microstructure of U-Mo monolithic fuel plates

The objective of this paper is to analyze the effect of different heat treatments on the fuel microstructure and texture in laboratory scale monolithic U-Mo fuel plates. Such analyses are relevant as they could possibly inform future fabrication methods for the optimization of microstructure and of material properties to ultimately improve fuel performance during irradiation. For this reason, detail characterization including Energy x-ray dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) techniques were applied on U-Mo plates fabricated with different heat treatments to understand the influence of fabrication on fuel microstructure. Here, U-Mo fresh fuel specimens with or without annealing treatments (homogenization and stress release annealing) after rolling were analyzed in this work. In this study for the first time EBSD was systematically used to analyze the heat treatments influence on texture present in fresh fuel monolithic U-Mo fuel plates. Such changes were connected to other known microstructural and chemical changes. In this work minimization of molybdenum concentration variation and gamma phase decomposition of the U-Mo fuel core after homogenization was observed. Also, an increase in the interaction layer of the U-Mo fuel core with the Zr interlayer diffusion barrier was observed with the UZr 2 growing up to 1 µm in thickness. Such microstructural changes were aligned to the changes in texture and grain structure. Indeed, common texture observed in body-centered cubic (BCC) metal after cold rolling (e.g., α, ξ, γ fibers) were minimized by the annealing/homogenization process. Moreover, grain structure was influenced by the fabrication route with elongated grains formed in the rolled sample and equiaxed grains found after annealing. Such features are relevant since the formation of microstructural features formed during fuel fabrication can impact fuel performance in reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrothermal corrosion and steam oxidation behavior comparison of UAM and conventional Zry-4

Here, hydrothermal corrosion and steam exposures on ultrasonic additively manufactured (UAM) Zircaloy-4 (Zry-4) specimens were conducted to compare to wrought Zry-4 performance in both simulated pressurized water reactor (PWR) operation (330°C, 15 MPa, <50 ppb oxygen, 500h) and representative accident conditions (100% H 2 O(g) at 700, 900, and 1100°C for up to 1h). UAM Zry-4 specimens showed 50% higher mass gain in PWR conditions and 50-80% more mass gain in steam oxidation due to internal oxidation between build layers in both cases. UAM Zry-4 in 900°C steam showed breakaway oxidation leading to sample deformation. Titanium used as an interlayer in the UAM process was detected in the substrate after the 1100°C exposure. Additional experiments to better link as-built defects to oxidation behavior are needed.

36 MATERIALS SCIENCE↗

Investigation of W-SiC compositionally graded films as a divertor material

W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. Here, this study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices.

36 MATERIALS SCIENCE↗

Effect of heat treatment on the microstructure of medium burn-up U-Mo monolithic fuel foils

Using scanning electron microscopy (SEM), this study evaluates the microstructure evolution of U-Mo fuel foils made with and without heat treatment at medium burn-up (of approximately 5 x 10 21 f/cm 3 ). The impact of annealing treatments on critical microstructural properties of the U-Mo fuel foils, including porosity, grain structure, Mo homogeneity, and fuel interaction with the Zr interlayer, was examined using large area lift outs (LALOs). The heat-treated specimens presented less grain refining at these burnups when compared to the un-heated specimens. Grain refinement was associated with porosities and fission products precipitation. Heat treatment can reduce fuel swelling during irradiation. Chemical inhomogeneity (Mo banding) was found to persist in the un-heated samples but was not present in the heat-treated samples. Thus, heat-treated U-Mo foils allows for more predictable fuel behavior under irradiation with respect to un-heated foils. The U-Mo and Zr interaction layer appears to be thicker and more continuous in the heat-treated sample which has been associated with stronger interface integrity during irradiation, as also observed in previous studies. These observations may indicate an overall improved performance of heat-treated fuel foil in a reactor. Further, the effect of local burn-up on grain size/refinement and porosities in each LALO specimen, sampled from different positions in the fuel foil, was difficult to analyze due to the large standard deviation of these parameters. Finally, evidence of grain refinement by polygonization may be present in these specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗