Search NASA⌕ Search

SEARCH · Search NASA

Results for “Curved Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Development of a multiaxial deformation measure and creep-fatigue damage summation for multiple load cycle types in support of an improved creep-fatigue design method

This report describes methods for extending the elastic perfectly plastic (EPP) simplified model test (SMT) approach to cover multiaxial load conditions and methods to combine EPP+SMT use fractions for multiple loading cycles. The completion of this work, in conjunction with companion reports on constructing and validating SMT design curves, marks the development of a complete methodology for assessing creep-fatigue damage in high temperature nuclear reactor structural components. This EPP+SMT method aims to better account for elastic follow up effects, simplify the design process, and reduce overconservatism when compared to current simplified bounding approaches in the ASME Boiler and Pressure Vessel Code Section III, Division 5, Subsection HB, Subpart B covering high temperature nuclear reactors.

36 MATERIALS SCIENCE↗

( NuSTAR NuSTAR) observations of the black hole GS 1354-645: evidence of rapid black hole spin

We present the results of a NuSTAR study of the dynamically confirmed stellar-mass black hole GS 1354−645. The source was observed during its 2015 “hard” state outburst; we concentrate on spectra from two relatively bright phases. In the higher-flux observation, the broadband NuSTAR spectra reveal a clear, strong disk reflection spectrum, blurred by a degree that requires a black hole spin of a=cJ/GM{sup 2}⩾0.98 (1σ statistical limits only). The fits also require a high inclination: θ≃75(2){sup ∘}. Strong “dips” are sometimes observed in the X-ray light curves of sources viewed at such an angle; these are absent, perhaps indicating that dips correspond to flared disk structures that only manifest at higher accretion rates. In the lower flux observation, there is evidence of radial truncation of the thin accretion disk. We discuss these results in the context of spin in stellar-mass black holes, and inner accretion flow geometries at moderate accretion rates.

79 ASTRONOMY AND ASTROPHYSICS↗

Hot, cold, and annual reference atmospheres for Edwards Air Force Base, California (1975 version)

Reference atmospheres pertaining to summer (hot), winter (cold), and mean annual conditions for Edwards Air Force Base, California, are presented from surface to 90 km altitude (700 km for the annual model). Computed values of pressure, kinetic temperature, virtual temperature, and density and relative differences percentage departure from the Edwards reference atmospheres, 1975 (ERA-75) of the atmospheric parameters versus altitude are tabulated in 250 m increments. Hydrostatic and gas law equations were used in conjunction with radiosonde and rocketsonde thermodynamic data in determining the vertical structure of these atmospheric models. The thermodynamic parameters were all subjected to a fifth degree least-squares curve-fit procedure, and the resulting coefficients were incorporated into Univac 1108 computer subroutines so that any quantity may be recomputed at any desired altitude using these subroutines.

Johnson, D. L.↗

Identification of XV-15 aeroelastic modes using frequency sweeps

The XV-15 tilt-rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier-transformed). Modal frequencies and damping were determined by performing curve fits to frequency-response magnitude and phase data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with predictions by two different programs, CAMRAD and ASAP.

Acree, C. W., Jr.↗

A simple analytic model for the evolution of captured galactic disks

The general analytic solution developed by Steinman-Cameron and Durisen and published in 1988 for the evolution of dissipative nonplanar disks is applied to captured galactic disks in model galaxies with nonspherical, scale-free, logarithmic gravitational potentials. Such potentials produce flat rotation curves, similar to those seen in real galaxies. In this case, the analytic solution yields a self-similar structure for the warps and twists that develop while the disks is settling. Being scale-free in a simple, analytic form, this solution is completely defined by only a few dimensionless fitting parameters. As a result, it can be utilized as a mathematical tool to fit settling disks in real galaxies. The minimum time it takes for a disk to settle into a steady state orientation is also a scale-free quantity when expressed in units of the precession period or the orbit period. For realistic parameters, settling times are on the order of one-half to two periods. The use of the time-dependent structure of settling disks as a probe of the three-dimensional mass distribution of the host galaxies, including dark halos, is discussed.

Steiman-Cameron, Thomas Y.↗

Bgridi - Interactive three-dimensional turbomachinery grid generation system with applications

An interactive, graphics-based grid generation system for 3D turbomachinery geometries has been developed. The system consists of separate modules for geometry modeling and grid generation. The grid generation method generates a series of 2D grids in the blade-to-blade passage to build up the 3D grid. A Poisson equation with forcing functions selected to control orthogonality and spacing on all boundaries is solved to generate the grid. Interactive definition of Bezier curves and surfaces as internal boundaries is used to improve control of grid quality. A multi-block data structure simpifies the creation of structured H-grids about complex turbomachinery geometries. The multi-block strategy facilitates the creation of a grid in the tip flow region, which is an important contributor to losses within the passage. The grid generation system is applied to several complex geometries including a simple radial impeller, a conventional turbine rotor, the SSME LOX turbine rotor with and without a tip flow grid, a multi-passage inducer-impeller, and a tip-flow cascade. In addition, a calculation of the tip-flow cascade flow field is shown.

Shoemaker, J. M.↗

Identification of 15-15 Aeroelastic Modes using Frequency-Domain Methods

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier-transformed). Modal frequencies and damping were determined by performing curve fits to frequency-response magnitude and phase data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with new predictions by two different programs, CAMRAD and ASAP.

Acree, C. W., Jr.↗

Surface Texture and Structure of ZnO Films Synthesized by Off-Axis Sputtering Deposition

Morphology and structure of ZnO films deposited on (0001) sapphire and glass substrates by off-axis sputtering are investigated at various temperatures and pressures. All films show highly textured structures on glass substrates and epitaxial growth on sapphire substrates. The full width at half maximum of theta rocking curves for epitaxial films is less than 0.5 degrees. In textured films, it rises to several degrees. The trend of surface textures in films grown at low pressures is similar to those grown at high temperatures. A morphology transition from large well-defined hexagonal grains to flat surface was observed at a pressure of 50 mtorr and temperature of 550 C. The experiment results are explained by the transport behavior of depositing species.

Zhu, Shen↗

First Results of Digital Topography Applied to Macromolecular Crystals

An inexpensive digital CCD camera was used to record X-ray topographs directly from large imperfect crystals of cubic insulin. The topographs recorded were not as detailed as those which can be measured with film or emulsion plates but do show great promise. Six reflections were recorded using a set of finely spaced stills encompassing the rocking curve of each reflection. A complete topographic reflection profile could be digitally imaged in minutes. Interesting and complex internal structure was observed by this technique.The CCD chip used in the camera has anti-blooming circuitry and produced good data quality even when pixels became overloaded.

Lovelace, J.↗

Polynomial Expressions for Estimating Elastic Constants From the Resonance of Circular Plates

Two approaches were taken to make convenient spread sheet calculations of elastic constants from resonance data and the tables in ASTM C1259 and E1876: polynomials were fit to the tables; and an automated spread sheet interpolation routine was generated. To compare the approaches, the resonant frequencies of circular plates made of glass, hardened maraging steel, alpha silicon carbide, silicon nitride, tungsten carbide, tape cast NiO-YSZ, and zinc selenide were measured. The elastic constants, as calculated via the polynomials and linear interpolation of the tabular data in ASTM C1259 and E1876, were found comparable for engineering purposes, with the differences typically being less than 0.5 percent. Calculation of additional v values at t/R between 0 and 0.2 would allow better curve fits. This is not necessary for common engineering purposes, however, it might benefit the testing of emerging thin structures such as fuel cell electrolytes, gas conversion membranes, and coatings when Poisson s ratio is less than 0.15 and high precision is needed.

Salem, Jonathan A.↗

NuSTAR Observations of the Black Hole GS 1354-645: Evidence of Rapid Black Hole Spin

We present the results of a NuSTAR study of the dynamically confirmed stellar-mass black hole GS 1354−645. The source was observed during its 2015 "hard" state outburst; we concentrate on spectra from two relatively bright phases. In the higher-flux observation, the broadband NuSTAR spectra reveal a clear, strong disk reflection spectrum, blurred by a degree that requires a black hole spin of a = cJ/ GM(sup 2) > or = 0.98 (1(sigma) statistical limits only). The fits also require a high inclination: theta approx. = 75(2)deg. Strong "dips" are sometimes observed in the X-ray light curves of sources viewed at such an angle; these are absent, perhaps indicating that dips correspond to flared disk structures that only manifest at higher accretion rates. In the lower flux observation, there is evidence of radial truncation of the thin accretion disk. We discuss these results in the context of spin in stellar-mass black holes, and inner accretion flow geometries at moderate accretion rates.

accretion disks↗

Water retention and gas relative permeability of two industrial concretes

This experimental study aims at identifying the water retention properties of two industrial concretes to be used for long term underground nuclear waste storage structures. Together with water retention, gas transfer properties are identified at varying water saturation level, i.e. relative gas permeability is assessed directly as a function of water saturation level S{sub w}. The influence of the initial de-sorption path and of the subsequent re-saturation are analysed both in terms of water retention and gas transfer properties. Also, the influence of concrete microstructure upon water retention and relative gas permeability is assessed, using porosity measurements, analysis of the BET theory from water retention properties, and MIP. Finally, a single relative gas permeability curve is proposed for each concrete, based on Van Genuchten-Mualem's statistical model, to be used for continuous modelling approaches of concrete structures, both during drying and imbibition.

36 MATERIALS SCIENCE↗

Effect of purity, edge length, and growth area on field emission of multi-walled carbon nanotube emitter arrays

Present report aims to study the effect of purity, edge length, and growth area on field emission of patterned carbon nanotube (CNT) emitter arrays. For development of four CNT emitter arrays (CEAs), low resistively silicon substrates were coated with thin film of iron catalyst using photolithography, sputtering, and lift off process. Four CEAs were synthesized on these substrates using thermal chemical vapor deposition with minor changes in pretreatment duration. Out of these, two CEAs have 10 {mu}m Multiplication-Sign 10 {mu}m and 40 {mu}m Multiplication-Sign 40 {mu}m solid square dots of CNTs with constant 20 {mu}m inter-dot separation. Other two CEAs have ring square bundles of CNTs and these CEAs are envisioned as 10 {mu}m Multiplication-Sign 10 {mu}m square dots with 4 {mu}m Multiplication-Sign 4 {mu}m scooped out area and 15 {mu}m Multiplication-Sign 15 {mu}m square dots with 5 {mu}m Multiplication-Sign 5 {mu}m lift out area with constant 20 {mu}m inter-dot spacing. Solid square dot structures have exactly constant edge length per unit area with more than four-fold difference in CNT growth area however ring square dot patterns have minor difference in edge length per unit area with approximately two times difference in CNT growth area. Quality and morphology of synthesized CEAs were assessed by scanning electron microscope and Raman characterization which confirm major differences. Field emission of all CEAs was carried out under same vacuum condition and constant inter-electrode separation. Field emission of solid square dot CEAs show approximately identical current density-electric field curves and Fowler-Nordheim plots with little difference in emission current density at same electric field. Similar results were observed for ring square structure CEAs when compared separately. Maximum emission current density observed from these four CEAs reduces from 14.53, 12.23, 11.01, to 8.66 mA/cm{sup 2} at a constant electric field of 5 V/{mu}m, according to edge length of 1361.7, 1221.08, 872.20, to 872.16 mm rather than growth area and purity. Although, the 40 {mu}m Multiplication-Sign 40 {mu}m CEAs possessed highest CNT growth area of 8.7 mm{sup 2} and best purity defined in terms of lowest defect band to graphitic band ratio of 0.614, the current observed from this CEAs was least.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Nanometer-scale structure differences in the myofilament lattice spacing of two cockroach leg muscles correspond to their different functions

ABSTRACT Muscle is highly organized across multiple length scales. Consequently, small changes in the arrangement of myofilaments can influence macroscopic mechanical function. Two leg muscles of a cockroach have identical innervation, mass, twitch responses, length–tension curves and force–velocity relationships. However, during running, one muscle is dissipative (a ‘brake’), while the other dissipates and produces significant positive mechanical work (bifunctional). Using time-resolved X-ray diffraction in intact, contracting muscle, we simultaneously measured the myofilament lattice spacing, packing structure and macroscopic force production of these muscles to test whether structural differences in the myofilament lattice might correspond to the muscles' different mechanical functions. While the packing patterns are the same, one muscle has 1 nm smaller lattice spacing at rest. Under isometric stimulation, the difference in lattice spacing disappeared, consistent with the two muscles' identical steady-state behavior. During periodic contractions, one muscle undergoes a 1 nm greater change in lattice spacing, which correlates with force. This is the first identified structural feature in the myofilament lattice of these two muscles that shares their whole-muscle dynamic differences and quasi-static similarities.

Tune, Travis Carver↗

Homogeneous Pt-bimetallic Electrocatalysts

Alloying has shown enormous potential for tailoring the atomic and electronic structures, and improving the performance of catalytic materials. Systematic studies of alloy catalysts are, however, often compromised by inhomogeneous distribution of alloying components. Here we introduce a general approach for the synthesis of monodispersed and highly homogeneous Pt-bimetallic alloy nanocatalysts. Pt{sub 3}M (where M = Fe, Ni, or Co) nanoparticles were prepared by an organic solvothermal method and then supported on high surface area carbon. These catalysts attained a homogeneous distribution of elements, as demonstrated by atomic-scale elemental analysis using scanning transmission electron microscopy. They also exhibited high catalytic activities for the oxygen reduction reaction (ORR), with improvement factors of 2-3 versus conventional Pt/carbon catalysts. The measured ORR catalytic activities for Pt{sub 3}M nanocatalysts validated the volcano curve established on extended surfaces, with Pt{sub 3}Co being the most active alloy.

30 DIRECT ENERGY CONVERSION↗

Correlated Spatiotemporal Evolution of Extreme-Ultraviolet Ribbons and Hard X-rays in a Solar Flare

We study the structure and evolution of solar flare ribbons in the chromosphere to infer properties of magnetic reconnection that occurs in the corona. We analyze the imaging observations of the M7.3 SOL2014-04-18T13 flare obtained by IRIS in both the near and far ultraviolet passbands and by SDO/AIA in the 1600A passband. Two flare ribbons are observed to spread away from the magnetic polarity inversion line as the flare progresses. Using the high-resolution IRIS observations, we measure the width of the newly brightened ribbon front along the extension of the ribbon, which maps the feet of magnetic field lines reconnecting in the current sheet in the corona. We find that the width of the ribbon front is highly structured, possibly reflecting corresponding structure in the coronal current layer. Further the ribbon grows most rapidly with time in regions where non-thermal hard X-ray (HXR) emission is concentrated (Brosius, et al. 2015). The light curve of the ultraviolet emissions in this region, as measured by IRIS and AIA, also well matches the HXR light curve at photon energies above 25 keV. In contrast, the ribbon-width evolution and light curves in other regions along the ribbons do not correlate well with the HXR emission. These results suggest that there is a strong connection between the production of non-thermal electrons and locally enhanced perpendicular extent of flare ribbon fronts, which reflect the inhomogeneous structure and/or reconnection dynamics of the flare current sheet in the corona.

Stephen Naus↗

Experiment 1: Orbital Processing of High-Quality Zn-Alloyed CdTe Compound Semiconductors

Zinc-alloyed cadmium telluride (Zn:CdTe) crystals were grown in unit gravity and in microgravity for comparative analysis. Two crystals were grown on USML-1/STS-50 in 1992, and two additional crystals were grown on USML-2/STS-73 in 1995. The Crystal Growth Furnace (CGF) in the seeded Bridgman-Stockbarger crystal growth geometry was utilized on both missions. Crystals grown on USML-1/STS-50 were found to have solidified with partial wall contact due to the near-absence of the hydrostatic pressure in microgravity, a residual g-vector that was not axial, and the nonwetting sample/ampoule wetting conditions. Crystals grown on USML-2/STS-73 included: a sample/ampoule identical to the USML-1/STS-73 sample/ampoule, with the addition of a restraining spring to simulate hydrostatic pressure internally, and a tapered ampoule which accomplished 2.2 cm of crystal growth without wall contact. Infrared transmission of all ground and flight samples was found to be 63-66 percent, very close to the theoretical 66 percent, suggesting good stoichiometric control. Infrared microscopy confirmed that the primary precipitates were Te and their size (1-10 microns) and density suggested that the flight- and ground-base samples experienced similar thermal histories. Longitudinal macrosegregation, calculated using scaling analysis, was predicted to be low. Nearly diffusion controlled growth was achieved even in unit gravity and macrosegregation data could be fit with a diffusion controlled model. Radial segregation was monitored and was found to vary with fraction solidified, particularly through the shoulder region, where the sample cross section was varying significantly. It was also disturbed in the flight samples in regions where asymmetric wall contact was noted. In regions where a steady state was established, the radial segregation was invariant within our experimental measurement error. Flight samples were found to be much higher in structural perfection than samples processed in unit gravity under identical growth conditions. In regions where solidification had occurred without wall contact, the free surfaces evidenced virtually no twinning, although twins appeared in the flight samples in regions of wall contact and were pervasive in the ground samples. These results were confirmed using optical microscopy and synchrotron x-ray white beam topography. Full-width half-maximum rocking curve widths (FWHM), recorded in arc-seconds, were significantly reduced from 20 a-s (1 g) to 9 a-s (micro-g) for the best regions of the crystals. The 9 a-s (FWHM) rocking curve value in the unconfined flight samples equals the best value reported terrestrially for this material. The ground samples exhibited a fully developed (111)[110] dislocation mosaic structure, whereas dislocations within the flight samples were discrete and no mosaic structure was evident. The defect density was quantitatively reduced from 75,000 (1 g) to 800 (micro-g) +/-50 percent. Dislocation etch pit density results were confirmed using transmission synchrotron white beam and monochromated beam topography. The low defect density is thought to have resulted from the near absence of hydrostatic pressure, which allowed the molten boule to solidify with little or no wall contact. This minimized the transfer of hoop stresses during solidification and post-solidification processing.

Larson, D. J., Jr.↗

X-ray diffraction and X-ray standing-wave study of the lead stearate film structure

A new approach to the study of the structural quality of crystals is proposed. It is based on the use of X-ray standing-wave method without measuring secondary processes and considers the multiwave interaction of diffraction reflections corresponding to different harmonics of the same crystallographic reflection. A theory of multiwave X-ray diffraction is developed to calculate the rocking curves in the X-ray diffraction scheme under consideration for a long-period quasi-one-dimensional crystal. This phase-sensitive method is used to study the structure of a multilayer lead stearate film on a silicon substrate. Some specific structural features are revealed for the surface layer of the thin film, which are most likely due to the tilt of the upper layer molecules with respect to the external normal to the film surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗