Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffusers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗

Lateral Diffusion Estimation in Fully Depleted Thick CCD Using Flat Field Image Analysis

In thick fully depleted CCDs charge carrier transport from the back window to the gates is accompanied by charge diffusion. Lateral diffusion smooths out density variations of the incoming photon flux by redistributing charges spatially. This creates short range positive correlations in recorded amplitudes. Pixel-to-pixel amplitude variations can also be caused by pixel size and quantum efficiency variations. Pixel size variations result in short range negative correlations. Our study shows that the characteristic diffusion width can be extracted from flat field data. The study was performed on fully depleted, thick CCDs produced in a technology study for the Large Synoptic Survey Telescope (LSST). Data were taken in the laboratory at bias voltages between -5 and -40 V. To increase statistical accuracy, images taken in identical conditions were co-added after base line subtraction and master files were produced. A flat field image simulator was developed for statistical comparison of simulated and measured images. Results on diffusion, pixel response variations, data features, analysis and modeling techniques are presented and discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Anisotropic diffusion of electrons in liquid xenon with application to improving the sensitivity of direct dark matter searches

Electron diffusion in a liquid xenon time projection chamber has recently been used to infer the z coordinate of a particle interaction, from the width of the electron signal. The goal of this technique is to reduce the background event rate by discriminating edge events from bulk events. Analyses of dark matter search data which employ it would benefit from increased longitudinal electron diffusion. We show that a significant increase is expected if the applied electric field is decreased. This observation is trivial to implement but runs contrary to conventional wisdom and practice. We also extract a first measurement of the longitudinal diffusion coefficient, and confirm the expectation that electron diffusion in liquid xenon is highly anisotropic under typical operating conditions.

79 ASTRONOMY AND ASTROPHYSICS↗

Electroluminescence pulse shape and electron diffusion in liquid argon measured in a dual-phase TPC

Here, we report the measurement of the longitudinal diffusion constant in liquid argon with the DarkSide-50 dual-phase time projection chamber. The measurement is performed at drift electric fields of 100 V/cm, 150 V/cm, and 200 V/cm using high statistics $^{39}$Ar decays from atmospheric argon. We derive an expression to describe the pulse shape of the electroluminescence signal (S2) in dual-phase TPCs. The derived S2 pulse shape is fit to events from the uppermost portion of the TPC in order to characterize the radial dependence of the signal. The results are provided as inputs to the measurement of the longitudinal diffusion constant DL, which we find to be (4.12 $\pm$ 0.04) cm$^2$/s for a selection of 140keV electron recoil events in 200V/cm drift field and 2.8kV/cm extraction field. To study the systematics of our measurement we examine datasets of varying event energy, field strength, and detector volume yielding a weighted average value for the diffusion constant of (4.09 $\pm$ 0.09) cm$^2$ /s. The measured longitudinal diffusion constant is observed to have an energy dependence, and within the studied energy range the result is systematically lower than other results in the literature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Helium diffusivity in oxide nuclear fuel: Critical data analysis and new correlations

Helium is relevant in determining nuclear fuel behaviour. It affects the performance of nuclear fuel both in reactor and in storage conditions. Helium becomes important in reactor conditions when high burnups are targeted or MOX fuel is used, whereas for storage conditions it can represent a threat to the fuel rods integrity. The accurate knowledge of helium behaviour combined with predictive model capabilities is fundamental for the safe management of nuclear fuel, with helium diffusivity being a critical property. For this reason, a considerable number of separate effect experiments in the last fifty years investigated helium diffusivity in nuclear fuel. The aim of this work is to critically review and assess the experimental results concerning the helium diffusivity. Experimental results are critically analysed in terms of the helium introduction technique used (either infusion, implantation or doping) and of sample characteristics (single crystal, poly-crystal or powder). Accordingly, we derived two different correlations for the diffusivity. Clearly, each of the new correlations corresponds to a limited range of application conditions, depending on the experimental data used to derive it. We provide recommendations regarding the proper application conditions for each correlation (e.g., in reactor or storage conditions).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Conditions for translation and scaling invariance of the neutron diffusion equation

Lie group methods are applied to the time-dependent, monoenergetic neutron diffusion equation in materials with spatial and time dependence. To accomplish this objective, the underlying 2nd order partial differential equation (PDE) is recast as an exterior differential system so as to leverage the isovector symmetry analysis approach. Some of the advantages of this method as compared to traditional symmetry analysis approaches are revealed through its use in the context of a 2nd order PDE. In this context, various material properties appearing in the mathematical model (e.g., a diffusion coefficient and macroscopic cross section data) are left as arbitrary functions of space and time. The symmetry analysis that follows is restricted to a search for translation and scaling symmetries; consequently the Lie derivative yields specific material conditions that must be satisfied in order to maintain the presence of these important similarity transformations. The principal outcome of this work is thus the determination of analytic material property functions that enable the presence of various translation and scaling symmetries within the time-dependent, monoenergetic neutron diffusion equation. The results of this exercise encapsulate and generalize many existing results already appearing in the literature. While the results contained in this work are primarily useful as phenomenological guides pertaining to the symmetry behavior of the neutron diffusion equation under certain assumptions, they may eventually be useful in the construction of exact solutions to the underlying mathematical model. Furthermore, the results of this work are also useful as a starting point or framework for future symmetry analysis studies pertaining to the neutron transport equation and its many surrogates.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Solute diffusion behavior during heat treatment and its impact in Sc-microalloyed Al-Cu system

Scandium (Sc) is a promising microalloying element that enhances the strength and thermal stability of aluminum (Al) alloys. However, these benefits are not fully realized in aluminum-copper (Al-Cu) systems, and corrosion resistance often declines due to the complex phase evolution and diffusion behavior of Cu and Sc. Here, to clarify this, solute diffusion behavior and Cu-Sc interaction during heat treatment (HT) were investigated using in situ synchrotron-based transmission x-ray microscopy (TXM), wide-angle x-ray scattering (WAXS), and x-ray absorption near-edge structure (XANES) spectroscopy. The results, supported by electron microscopy, reveal strong Cu-Sc bonding that significantly impedes solute diffusion, leading to inhomogeneous solute distribution and non-uniform precipitation. Moreover, the Al-Cu-Sc eutectic phase exhibits high thermal stability, resisting dissolution even near the matrix liquidus. These findings quantitatively elucidate the sluggish diffusion kinetics of Cu and Sc, which can help redesign HT schedules to improve both mechanical properties and corrosion resistance in Sc-microalloyed Al-Cu alloys.

36 MATERIALS SCIENCE↗

Temperature-dependent diffuse reflectance measurements of ceramic powders in the near- and mid-infrared spectra

Radiative properties are critical to quantify radiative energy fluxes between surfaces and in participating media. However, there is limited experimental data on temperature-dependent radiative properties of materials. Herein, this work focuses on experimentally measuring temperature-dependent diffuse reflectance in the near- and mid-infrared spectra (1–20 μm) for ceramic particles with applications as heat-transfer and thermal-storage media in concentrated solar power (CSP) plants. Specifically, a commercially available sintered bauxite proppant, ACCUCAST ID80, and its primary chemical constituents—alumina (Al 2 O 3 ) and silica (SiO 2 )—are measured in powder form using a Fourier transform infrared spectrometer (FTIR) coupled with a specialized diffuse reflectance accessory and a heated stage. Room-temperature diffuse reflectance measurements show increased absorption in tests with greater mass fractions of the ceramic samples. There is a strong correlation in the measured reflectance spectra of ACCUCAST with alumina and silica in the spectral range 2000–500 cm –1 (5–20 μm). Whereas, for shorter wavelengths (< 5 μm), the absorptance for ACCUCAST is greater than the absorptance for alumina and silica, indicating contributions from other chemical species present in the composite material. For the first time, temperature-dependent diffuse reflectance measurements are reported for ACCUCAST up to 1000 °C. These results are compared against those of alumina and silica through the calculation of a thermal emittance. All three materials exhibit a calculated emittance of ~0.9 at room temperature. However, this value decreases to ~0.6 for ACCUCAST and drops to less than 0.4 for alumina and silica at 1000 °C. Thermal cycling in air at 1000 °C resulted in a visible color change from dark grey to light orange for ACCUCAST and a subsequent larger increase in reflectance for wavelengths less than 5 μm as compared to ACCUCAST thermally cycled at 1000 °C in vacuum. Alumina and silica spectra proved to be largely unaffected by thermal cycling under atmospheric conditions. Overall, this study establishes a powerful technique for the characterization of radiative properties of particulate materials as a function of temperature and presents a detailed case study of ACCUCAST, a candidate for next-generation particle-based CSP.

14 SOLAR ENERGY↗

The effect of heat treatment on structural and electronic properties of niobium nitride prepared by a thermal diffusion method

NbN coatings are prepared onto Nb substrate by thermal diffusion at high temperatures. The formation of NbN coating by thermal diffusion was studied in the range of 1250-1500 °C at constant nitrogen background gas pressure (1.3x10 -3 Pa) and processing time (180 min). The electronic and crystal structures of the NbN coatings were investigated. It was found that nitrogen diffuses into Nb forming the Nb-N solid solution (bcc) a-NbN phase that starts to appear above 1250 °C. Increasing the processing temperature gives richer a-phase concentration. Besides, X-ray absorption spectroscopy (XAS) was performed to study the electronic structure of the NbN layer. The results of the electronic structural study corroborate the crystal structural analysis. The Nb M 3,2 edge X-ray absorption spectroscopy (XAS) spectrum shows strong temperature dependence. At the highest processing temperature (1500 °C), the number of d holes increased. Nitrogen diffusion into Nb is resulting to increase electrostatic interaction between d electron and core hole. Lastly, for the studied conditions, only the α-NbN was observed in the X-ray diffraction patterns.

36 MATERIALS SCIENCE↗

Absorption of ethanol, acetone, benzene and 1,2-dichloroethane through human skin in vitro: a test of diffusion model predictions

The overall goal of this research was to further develop and improve an existing skin diffusion model by experimentally confirming the predicted absorption rates of topically-applied volatile organic compounds (VOCs) based on their physicochemical properties, the skin surface temperature, and the wind velocity. In vitro human skin permeation of two hydrophilic solvents (acetone and ethanol) and two lipophilic solvents (benzene and 1,2-dichloroethane) was studied in Franz cells placed in a fume hood. Four doses of each {sup 14}C-radiolabed compound were tested — 5, 10, 20, and 40 μL cm{sup −2}, corresponding to specific doses ranging in mass from 5.0 to 63 mg cm{sup −2}. The maximum percentage of radiolabel absorbed into the receptor solutions for all test conditions was 0.3%. Although the absolute absorption of each solvent increased with dose, percentage absorption decreased. This decrease was consistent with the concept of a stratum corneum deposition region, which traps small amounts of solvent in the upper skin layers, decreasing the evaporation rate. The diffusion model satisfactorily described the cumulative absorption of ethanol; however, values for the other VOCs were underpredicted in a manner related to their ability to disrupt or solubilize skin lipids. In order to more closely describe the permeation data, significant increases in the stratum corneum/water partition coefficients, K{sub sc}, and modest changes to the diffusion coefficients, D{sub sc}, were required. The analysis provided strong evidence for both skin swelling and barrier disruption by VOCs, even by the minute amounts absorbed under these in vitro test conditions. - Highlights: • Human skin absorption of small doses of VOCs was measured in vitro in a fume hood. • The VOCs tested were ethanol, acetone, benzene and 1,2-dichloroethane. • Fraction of dose absorbed for all compounds at all doses tested was less than 0.3%. • The more aggressive VOCs absorbed at higher levels than diffusion model predictions. • We conclude that even small exposures to VOCs temporarily alter skin permeability.

60 APPLIED LIFE SCIENCES↗

Role of Short-Range Order on Diffusion Coefficients in the Li–Mg Alloy

Li–Mg alloys are important because of their beneficial role in fostering uniform plating and stripping of lithium in all-solid-state batteries. The alloy Li x Mg 1–x forms a solid solution on the BCC crystal structure when the lithium content is greater than x ≈ 0.3. The activation barriers of lithium and magnesium exchanges with a vacancy, crucial for substitutional diffusion, are predicted to be exceptionally low and almost identical, with negligible dependence on the alloy composition. The equilibrium vacancy concentration at room temperature is predicted to be very low, and it also remains almost constant with no dependence on Mg content in the alloy (for x Li ≥ 0.5). Nevertheless, both experiments and kinetic Monte Carlo simulations indicate that the tracer diffusion coefficients decrease by almost an order of magnitude with the addition of Mg to the alloy. In this contribution, the crucial role that chemical short-range order plays in affecting the diffusion coefficients is studied. Chemical short-range order is found to increase the effective activation barrier for lithium and magnesium diffusion by making successive atomic hops with vacancies correlated.

36 MATERIALS SCIENCE↗

Particle-Phase Diffusion Modulates Partitioning of Semivolatile Organic Compounds to Aged Secondary Organic Aerosol

The diffusivity of semivolatile organic compounds (SVOCs) in the bulk particle phase of a viscous atmospheric secondary organic aerosol (SOA) can have a profound impact on aerosol growth and size distribution dynamics. Here, we investigate the bulk diffusivity of SVOCs formed from photo-oxidation of isoprene as they partition to a bimodal aerosol consisting of an Aitken (potassium sulfate) and accumulation mode (aged α-pinene SOA) particles as a function of relative humidity (RH). The model analysis of the observed size distribution evolution shows that liquid-like diffusion coefficient values of D b > 10 –10 cm 2 s –1 fail to explain the growth of the Aitken mode. Instead, much lower values of Db between 2.5 × 10 –15 cm 2 s –1 at 32% RH and 8 × 10 –15 cm 2 s –1 at 82% RH were needed to successfully reproduce the growth of both modes. The diffusivity within the aged α-pinene SOA remains appreciably slow even at 80% RH, resulting in hindered partitioning of SVOCs to large viscous particles and allowing smaller and relatively less viscous particles to effectively absorb the available SVOCs and grow much faster than would be possible otherwise. Our results have important implications for modeling SOA formation and growth in the ambient atmosphere.

54 ENVIRONMENTAL SCIENCES↗

Temperature-Dependent Constrained Diffusion of Micro-Confined Alkylimidazolium Chloride Ionic Liquids

Alkylimidazolium chloride ionic liquids (ILs) have many uses in a variety of separation systems, including micro-confined separation systems. To understand the separation mechanism in these systems, the diffusion properties of analytes in ILs under relevant operating conditions, including micro-confinement dimension and temperature, should be known. For example, separation efficiencies for various IL-based microextraction techniques are dependent on the sample volume and temperature. Temperature-dependent (20–100 °C) fluorescence recovery after photobleaching (FRAP) was utilized to determine the diffusion properties of a zwitterionic, hydrophilic dye, ATTO 647, in alkylimidazolium chloride ILs in micro-confined geometries. These micro-confined geometries were generated by sandwiching the IL between glass substrates that were separated by ~1 to 100 μm. From the measured temperature-dependent FRAP data, we note alkyl chain length-, thickness-, and temperature-dependent diffusion coefficients, with values ranging from 0.021 to 46 μm 2 /s. Deviations from Brownian diffusion are observed at lower temperatures and increasingly less so at elevated temperatures; the differences are attributed to alterations in intermolecular interactions that reduce temperature-dependent nanoscale structural heterogeneities. Furthermore, the temperature- and thickness-dependent data provide a useful foundation for efficient design of micro-confined IL separation systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Prediction of Self-Diffusion in Binary Fluid Mixtures Using Artificial Neural Networks

Artificial neural networks (ANNs) were developed to accurately predict the self-diffusion constants for individual components in binary fluid mixtures. The ANNs were tested on an experimental database of 4328 self-diffusion constants from 131 mixtures containing 75 unique compounds. The presence of strong hydrogen bonding molecules may lead to clustering or dimerization resulting in non-linear diffusive behavior. To address this, self- and binary association energies were calculated for each molecule and mixture to provide information on intermolecular interaction strength and were used as input features to the ANN. An accurate, generalized ANN model was developed with an overall average absolute deviation of 4.1%. Forward input feature selection reveals the importance of critical properties and self-association energies along with other fluid properties. Additional ANNs were developed with subsets of the full input feature set to further investigate the impact of various properties on model performance. The results from two specific mixtures are discussed in additional detail: one providing an example of strong hydrogen bonding and the other an example of extreme pressure changes, with the ANN models predicting self-diffusion well in both cases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Proton Diffusion in Liquid 1,2,3-Triazole Studied by Incoherent Quasi-Elastic Neutron Scattering

Improving the proton transport in polymer electrolytes impacts the performance of next-generation solid-state batteries. However, little is known about proton conductivity in nonaqueous systems due to the lack of an appropriate level of fundamental understanding. Here, we studied the proton transport in small molecules with dynamic hydrogen bonding, 1,2,3-triazole, as a model system of proton hopping in a nonaqueous environment using incoherent quasi-elastic neutron scattering. By using the jump-diffusion model, we identified the elementary jump-diffusion motion of protons at a much shorter length scale than those by nuclear magnetic resonance and impedance spectroscopy for the estimated long-range diffusion. In addition, a spatially restricted diffusive motion was observed, indicating that proton motion in 1,2,3-triazole is complex with various local correlated dynamics. In conclusion, these correlated dynamics will be important in elucidating the nature of the proton dynamics in nonaqueous systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Do TFSA anions slither? Pressure exposes the role of TFSA conformational exchange in self-diffusion

Multi-nuclear ( 1 H, 2 H, and 19 F) magnetic resonance spectroscopy techniques as functions of temperature and pressure were applied to the study of selectively deuterated 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide (EMIM TFSA) ionic liquid isotopologues and related ionic liquids. For EMIM TFSA, temperature-dependent 2 H T 1 data indicate stronger electric field gradients in the alkyl chain region compared to the imidazolium ring. Most significantly, the pressure dependences of the EMIM and TFSA self-diffusion coefficients revealed that the displacements of the cations and anions are independent, with diffusion of the TFSA anions being slowed much more by increasing pressure than for the EMIM cations, as shown by their respective activation volumes (28.8 ± 2.5 cm³/mol for TFSA vs. 14.6 ± 1.3 cm³/mol for EMIM). Increasing pressure may lower the mobility of the TFSA anion by hindering its interconversion between trans and cis conformers, a process that is coupled to diffusion according to published molecular dynamics simulations. Measured activation volumes (ΔV ‡ ) for ion self-diffusion in EMIM bis(fluoromethylsulfonyl)amide and EMIM tetrafluoroborate support this hypothesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reduced Artifact Approach for Determining Diffusion Coefficients in Time-Resolved Microscopy

Ultrafast microscopy methods traditionally assume a Gaussian profile to extract excited state diffusivities from transport measurements. Although this fitting method recovers accurate diffusion coefficients when the point spread function is well-represented by a Gaussian, even minor spatial aberrations introduced by the imaging system cause significant errors in the determined value. To provide a more accurate measure of excited state transport in nano- and microscale materials systems, in this work an alternative analysis protocol is proposed that numerically convolves the Green’s function solution to the diffusion equation with the experimentally measured point spread function. In contrast to the Gaussian fitting approach, the numerical convolution is shown to be robust against artifacts caused by nonideal point spread functions. Furthermore, the numerical convolution approach is highly effective at resolving anisotropic diffusion in modeled data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ab Initio Simulations of Tritium Diffusion in Al-Rich Iron Aluminide Coating Phases

Surface coatings of steels used in extreme conditions and corrosive environments generally aim to provide protection and increased durability. In the case of tritium-producing burnable absorber rods (TPBARs) used in nuclear reactors, a 316 stainless steel has been coated with Al. Scanning transmission electron microscopy (STEM) characterization of the coating found three Al-rich (>60 atom % Al) iron aluminide alloys identified as hexagonal FeNiAl 5 , monoclinic Fe 4 Al 13 , and orthorhombic Fe 2 Al 5 . Density functional theory simulations using nudged elastic band have been performed to investigate the diffusion of interstitial tritium in each Al-rich iron aluminide phase. While FeNiAl 5 and Fe 4 Al 13 can be viewed as the stacking of two layers, the structural peculiarity of Fe 2 Al 5 is that channels of variable Al vacancy content are present along the c-axis. Therefore, three stoichiometries for Fe 2 Al x phase, namely, Fe 2 Al 4 , Fe 2 Al 5 , and Fe 2 Al 6 , have been considered to evaluate the impact of Al vacancy concentration on tritium diffusion behavior. Altogether, we found that at 600 K, tritium diffusion decreases from a faster rate in the channels of Fe 2 Al x phases (D T ≤ 10 –11 m 2 ·s –1 ) to Fe 4 Al 13 (D T ≈ 10–12 m2·s–1), and finally in FeNiAl5 (D T ≈ 10 –13 m 2 ·s –1 ). Here, we also find that interstitial tritium generally diffuses faster in Fe–Al coating phases than in the tritium breeding material γ-LiAlO 2 (D T ≈ 10 –14 m 2 ·s –1 ) but slightly slower than in 316 stainless steel (D T ≈ 10 –10 m 2 ·s –1 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗