Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distributed temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Power control system modification and simulation of CPR1000 - 181

Due to development of electric power system, the proportion of nuclear power and its needs for load follow operation have become large. Then there would be higher requirements to the power control ability of the nuclear power system. The axial power distribution may change a lot in the operation process and be affected by many factors. In particular, as the power change is performed within a load follow maneuver, several modifications occur in the core from a neutronic view point: the fuel and moderator temperature change, the xenon concentration and distribution are modified, the power distribution skewed axially, etc. These changes need to be adequately counterbalanced to keep both the core critical and the power distribution acceptable. The traditional approach in pressurized water reactors (PWRs) is compensating for the reactivity change due to the power variation by adjusting the soluble boron concentration and moving a limited number of control banks. However, dilution/boronation strategy becomes expensive for short time changes and leads to large volume of liquid effluent, so it is eager about a capability to perform load follow operation without changing soluble boron concentration. CPR1000, one of the main reactor types in China national development, is taken an example in this paper. It adopts a control method called Mode G, using G banks, N banks, R bank and soluble boron to perform the load follow control. According to the analysis of the physics and thermal principle, a two-node dynamic function model was built, putting the coupling coefficient and mutual influence into consideration. By the calculation of these transient parameter values which are acquired by the steady-state calculation of single channel, the core system model of CPR1000 is established. In order to carry out the load follow operation without the boron adjustment, named as BTP mode, the control banks were regrouped to control the average temperature by M banks and axial offset by AO bank. After that, the average temperature control system (M banks control system) and the axial offset control system (AO bank control system) are built. When the optimal control system is connected to the core model simulation platform, the BTP mode load follow operation of the modified CPR1000 is simulated in the end of the paper. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Plasma-parameter dependence of ro-vibrational temperatures for H 2 in LHD divertor

We analyzed a thousand visible spectra of Fulcher-α band measured for divertor plasmas in Large Helical Device. With a coronal model and Bayesian inference, the population distribution of hydrogen molecule in the electronic ground state was estimated. The non-thermal population distribution was recovered with a two-temperature model, which has two sets of rotational and vibrational temperatures, as well as their mixture coefficient. The lower rotational temperature significantly changes according to the plasma parameters. Its nearly linear dependence on the electron density was found, which is consistent with previous works. The lower vibrational temperature also shows a small density dependence, as reported by a previous work. On the other hand, the higher rotational and vibrational temperatures as well as the mixture coefficient only show slight changes over the broad range of plasma parameters. These population parameters show a significant correlation; with higher electron density, all the temperatures and the fraction of the higher-temperature component increase simultaneously. In conclusion, this suggests that the electron impact plays an important role to determine the population distribution.

42 ENGINEERING↗
DOE OSTI2021

Seabird distribution is better predicted by abundance of prey than oceanography. A case study in the Gulf of Cadiz (SW, Iberian Peninsula)

Abstract Quantifying factors that influence marine predator distributions is essential to understanding the current and future change in marine biodiversity. Here, we test whether marine predator distribution relates to prey, or is better predicted by other specific habitat features. We examine the correlation between spatial distribution of three seabird species and their prey, as well as environmental proxies (oceanographic characteristics) in the Gulf of Cadiz, NE Atlantic. We modeled the at-sea distribution of Cory's shearwater, Balearic shearwater and Northern gannet, based on: (i) pelagic fish abundance according to acoustic surveys, and (ii) a forecast-model of remotely sensed environmental variables (productivity, sea surface temperature, and salinity). In general, seabird distributions were better predicted by abundance of fish than by environmental variables at the habitat scale. We obtained consistent correlations between seabird presence and the abundance of medium-sized (10–20 cm) sardines, anchovies and Mediterranean horse mackerel, providing information on their preferred prey. Additionally, oceanographic productivity variables moderately contributed to seabird distribution models, with better predictive value for the critically endangered Balearic shearwater and Northern gannet in the summer, whilst the model for Cory's shearwater's produced poorer predictions. Predator–prey combined studies may represent essential tools for an efficient ecosystem-based management of marine environments.

de la Cruz, Andrés (ORCID:0000000203632498)↗
DOE OSTI2022

Size and Distribution of Parr Produced from Natural‐ and Hatchery‐Origin Steelhead Spawning Naturally in a Small Pacific Northwest Coastal Stream

Abstract Recent studies suggest that steelhead Oncorhynchus mykiss produced from local hatchery‐origin (HOR) adults have lower lifetime fitness than their natural‐origin (NOR) counterparts. To increase our understanding of this pattern, we compared age‐1 parr size and distribution produced by a local integrated population of HOR and NOR adults spawning naturally across a range of environmental conditions. Across 8 years, we used genetic parentage assignments and field measurements of parr in conjunction with creek temperature and flow data to find small, nonbiologically significant differences in size between parr of different parent origins. This suggests that parr produced by HOR adults are acquiring enough resources to grow at a rate similar to that of parr produced by NOR adults. In contrast to origin, we found strong positive associations between mean size of parr and annual mean water temperature and summer flow. Additionally, the distribution of parr was similar and HOR‐produced parr were not skewed relative to the location of the hatchery. Parr occupying the full extent of accessible and suitable habitat might be a positive outcome for hatchery programs seeking to supplement an existing population or replace an extirpated population. However, these results also imply that HOR fish could be competing with NOR fish for food and space, which might be less desirable if the goal of the hatchery program is harvest and not supplementation. Our results highlight the importance of clearly articulated goals for the hatchery program, as the observed pattern could be deemed a benefit or a risk depending on the hatchery's purpose. Lastly, projections for higher water temperatures and reduced summer flows, when considered in the context of the correlations we observed for size of parr, imply that coastal steelhead populations could start experiencing negative climate impacts with respect to steelhead parr growth metrics during the summer in the next few decades.

Kennedy, Benjamen M.↗
DOE OSTI2023

Double-sided electron energy analyzer for measurement of non-Maxwellian electron energy distributions

Here, a double-sided electron energy analyzer is developed for studies of magnetic reconnection. It can measure electron energy distribution functions along two directions opposite to each other at the same time. Each side is composed of a floating reference grid, an energy selector grid, and a collector plate. The voltage of the selector grid is swept from –40 to 0 V with respect to the reference grid with a frequency of 1 MHz. This fast sweeping is required to resolve sub-Alfvénic changes in plasma quantities of the Magnetic Reconnection Experiment, where the typical Alfvénic time is a few microseconds. The reliability of the energy analyzer is checked in Maxwellian plasmas away from the reconnection region. In this case, the electron temperature computed from the electron energy distribution function agrees with measurements of a reference triple Langmuir probe. When it is located near the reconnection region, the temperatures of the tail electron population from both sides, facing into the electron flow and facing away from it, exceed the bulk electron temperature measured by the Langmuir probe by a factor of about 2.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Holistic Numerical Calibration of the iMESA Electrostatic Analyzer

A drifted Maxwellian velocity distribution is the most common model used to interpret the data from low-energy charged-particle instruments onboard spacecraft that are used to investigate the ambient plasma environment in the low Earth orbit (LEO). An original method is presented for determining the flow parameters (density, temperature, and flow energy) of such a distribution from the output of the integrated miniaturized electrostatic analyzer, which has been successfully flown on several LEO missions. Rather than attempting to deconvolve from the on-orbit data the analyzer’s response to an ideal, monoenergetic input, numerical simulation is used to predict and parameterize the response of the device to an input distribution that includes an isotropic, non-zero temperature, yielding a straightforward method for extracting the flow parameters from the spacecraft data. The method is computationally simple enough to be incorporated into a robust algorithm suitable for rapid batch processing or real-time analysis of data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Bayesian analysis for estimating statistical parameter distributions of elasto-viscoplastic material models

High temperature design methods rely on constitutive models for inelastic deformation and failure typically calibrated against the mean of experimental data without considering the associated scatter. Variability may arise from the experimental data acquisition process, from heat-to-heat material property variations, or both and need to be accurately captured to predict parameter bounds leading to efficient component design. Applying the Bayesian Markov Chain Monte Carlo (MCMC) method to produce statistical models capturing the underlying uncertainty in the experimental data is an area of ongoing research interest. This work varies aspects of the Bayesian MCMC method and explores their effect on the posterior parameter distributions for a uniaxial elasto-viscoplastic damage model using synthetically generated reference data. From our analysis with the uniaxial inelastic model we determine that an informed prior distribution including different types of test conditions results in more accurate posterior parameter distributions. The parameter posterior distributions, however, do not improve when increasing the number of similar experimental data. Additionally, changing the amount of scatter in the data affects the quality of the posterior distributions, especially for the less sensitive model parameters. Moreover, we perform a sensitivity study of the model parameters against the likelihood function prior to the Bayesian analysis. The results of the sensitivity analysis help to determine the reliability of the posterior distributions and reduce the dimensionality of the problem by fixing the insensitive parameters. The comprehensive study described in this work demonstrates how to efficiently apply the Bayesian MCMC methodology to capture parameter uncertainties in high temperature inelastic material models. Quantifying these uncertainties in inelastic models will improve high temperature engineering design practices and lead to safer, more effective component designs.

42 ENGINEERING↗
DOE OSTI2021

Evidence Theory Representations for Properties Associated With Weak Link/Strong Link Systems, Part 3: Margins for Failure Time and Failure Temperature

The use of evidence theory and associated cumulative plausibility functions (CPFs), cumulative belief functions (CBFs), cumulative distribution functions (CDFs), complementary cumulative plausibility functions (CCPFs), complementary cumulative belief functions (CCBFs), and complementary cumulative distribution functions (CCDFs) in the analysis of time and temperature margins associated with loss of assured safety (LOAS) for one weak link (WL)/two strong link (SL) systems is illustrated. Article content includes cumulative and complementary cumulative belief, plausibility, and probability for (i) SL/WL failure time margins defined by (time at which SL failure potentially causes LOAS) – (time at which WL failure potentially prevents LOAS), (ii) SL/WL failure temperature margins defined by (the temperature at which SL failure potentially causes LOAS) – (the temperature at which WL failure potentially prevents LOAS), and (iii) SL/SL failure temperature margins defined by (the temperature at which SL failure potentially causes LOAS) – (the temperature of SL whose failure potentially causes LOAS at the time at which WL failure potentially prevents LOAS).

42 ENGINEERING↗
DOE OSTI2020

Projecting spatiotemporally explicit effects of climate change on stream temperature: A model comparison and implications for coldwater fishes

Conservation planners and resource managers seek information about how the availability and locations of cold-water habitats will change in the future and how these predictions vary among models. In this work, we used a physical process-based model to demonstrate the implications of climate change for streamflow and water temperature in two watersheds with distinctive flow regimes: the Snoqualmie watershed (WA) and Siletz watershed (OR), USA. Our model incorporated a downscaled ensemble of global climate model outputs and was calibrated with in situ and remotely sensed water temperatures. Furthermore, we compared predictions from our processed-based model to those from a publicly available and widely used statistical model. The process-based model projected greater changes in summer maximum water temperatures for the mixed-rain-snow Snoqualmie watershed than for the rain-dominated Siletz watershed as a result of the near-complete loss of winter snowpack and significant reduction in summer flow in the Snoqualmie watershed expected by the 2080s. Both models projected generally similar future spatial patterns of maximum water temperature in the two rivers, with cool reaches distributed farther upstream and fewer in number. However, the process-based model projected higher spatial heterogeneity in water temperature due to our spatially explicit simulation of streamflow and because we calibrated the model with spatially continuous remotely sensed water temperature data. We used stream temperature projections to assess the vulnerability of Pacific salmon and trout to changes in the spatial distribution of cold-water habitats during August by the 2080s. Results suggest that salmonids may have fewer summertime cold-water habitats in both watersheds. Projected stream warming may further limit particular species and life stages, especially in the Snoqualmie watershed. Our comparison of models highlights the importance of considering what might be gained by using a process-based model for evaluating and prioritizing management actions that mitigate climate impacts on cold-water habitats for stream fishes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Effect of an increase in the density of collision cascades on the efficiency of the generation of primary displacements during the ion bombardment of Si

The depth distributions of structural damage induced in Si at room temperature by the implantation of P and PF{sub 4} with energies from 0.6 to 3.2 keV/amu are experimentally studied in a wide range of doses. It is found that, in all cases, the implantation of molecular PF{sub 4} ions forms practically single-mode defect distributions, with maximum at the target surface. This effect is caused by an increase in the generation of primary defects at the surface of the target. Individual cascades formed by atoms comprising molecule effectively overlap in the surface vicinity; this overlap gives rise to nonlinear processes in combined cascades due to a high density of displacements in such cascades. Quantitative estimation of increase of effectiveness of point defect generation by PF{sub 4} ions in respect to P ions is done on the base of experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Changes in Ion-Current Composition in the Process of Field Evaporation of Tungsten at High Temperatures

Field evaporation of tungsten at T ~ 2000 K was studied using a sector magnetic mass spectrometer with a field ion source and a field emission microscope. Only low-charge ions W{sup +2} and W{sup +} of all W isotopes were observed in the process of evaporation. The mass distribution of ion currents of isotopes agreed roughly with the standard isotopic ratio for natural tungsten, although certain deviations from it, which were attributed to fluctuations and the erratic nature of evaporation process, were also detected.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Predicting properties of gas and solid streams by intrinsic kinetics of fast pyrolysis of wood

Pyrolysis has the potential to create a biocrude oil from biomass sources that can be used as fuel or as feedstock for subsequent upgrading to hydrocarbon fuels or other chemicals. The product distribution/composition, however, is linked to the biomass source. This work investigates the products formed from pyrolysis of woody biomass with a previously developed chemical kinetics model. Different woody feedstocks reported in prior literature are placed on a common basis (moisture, ash, fixed carbon free) and normalized by initial elemental composition through ultimate analysis. Observed product distributions over the full devolatilization range are explored, reconstructed by the model, and verified with independent experimental data collected with a microwave-assisted pyrolysis system. These trends include production of permanent gas (CO, CO 2 ), char, and condensable (oil, water) species. Elementary compositions of these streams are also investigated. As a result, close agreement between literature data, model predictions, and independent experimental data indicate that the proposed model/method is able to predict the ideal distribution from fast pyrolysis given reaction temperature, residence time, and feedstock composition.

09 BIOMASS FUELS↗
DOE OSTI2024

Butene-Rich Alkene Formation from 2,3-Butanediol through Dioxolane Intermediates

The cost-effective production of sustainable aviation fuels (SAF) remains a major challenge within the energy sector. One approach to address this is the fermentation of biomass feedstocks into oxygenates followed by catalytic conversion to alkenes or other oligomerization precursors. 2,3-Butanediol (BDO) is a promising fermentation product due to its four-carbon nature, its decreased microorganism toxicity and associated higher maximum fermentation titers relative to other alcohols and oxygenates, and its capacity to be readily converted into butene isomers and longer chain alkenes. BDO conversion is currently constrained by separation challenges for BDO isolation due to its high boiling point and hydrophilicity. Here, this work expands upon previous BDO reactive separation via dioxolane formation over a solid acid catalyst by investigating the conversion of dioxolanes into alkene mixtures. Dioxolanes were formed from a range of aldehydes and subsequently converted over a Cu/ZSM-5 catalyst (448–523 K) via an ether cleavage, hydrogenation, and dehydration reaction network to form alkene-rich product mixtures (96% C 3+ alkene yield, 523 K). This selectivity is greater than that of direct BDO conversion to alkenes over an identical catalyst (89%, 523 K). C 3+ alkene selectivity is maximized between 498 and 523 K at complete dioxolane conversion without significant alkene hydrogenation to alkanes. The alkene product distributions can be tailored via both aldehyde selection during dioxolane formation and the dioxolane conversion reaction temperature. Alkene mixtures from dioxolane conversion predominantly reflect the carbon chain length and stereochemistry of BDO and the initial aldehyde at or below 498 K, yet higher reaction temperatures yield alkene mixtures of similar carbon chain distributions, regardless of initial aldehyde selection. Deactivation of the Cu/ZSM-5 catalyst is observed for multiple steps of the overall reaction network but can be minimized by facilitating the complete dioxolane-to-alkene reaction network at temperatures of at least 498 K.

2,3-butanediol↗
DOE OSTI2026

Validation Studies of RELAP5-3D for High-Temperature Gas-Cooled Reactor Analysis Using a Refined RELAP5-3D Model of the High Temperature Test Facility

RELAP5-3D has been used extensively for high-temperature gas-cooled reactor (HTGR) analysis, but such analysis lies outside the validation basis for the code. Oregon State University (OSU) and the United States Department of Energy’s (DOE) Advanced Reactor Technologies (ART) – Gas-cooled reactor campaign worked together to design and operate the High Temperature Test Facility (HTTF) at OSU to provide validation data for prismatic HTGR thermal hydraulics analysis. Work using a previous RELAP5-3D model of HTTF demonstrated the ability to reproduce trends in HTTF data but an inability to reproduce the values measured in multiple experiments within the uncertainty. It was hypothesized that a new model with a finer radial nodalization would perform better for HTTF analysis. In this paper, we present the development of that more refined model and analyze HTTF experiments PG-27 and PG-29, a pressurized (PCC) and depressurized conduction cooldown (DCC) transient. Comparing PG-27 results to experimental data shows a better prediction of steady state and transient temperatures; however, a deeper dive reveals that better transient temperature predictions are a result of better initial conditions. The transient temperature rise in the core is comparable between the two models, but the legacy model predicts temperatures in the reflectors better. The new model demonstrates the ability to predict unique temperatures in each sector of the core during PG-29, capturing the azimuthal asymmetry; however, the temperature predictions still differ from measured temperatures. One hypothesis is that differences between the assumed and actual power distribution leads to the underprediction of the individual block temperatures. These results suggest that gaps and uncertainties in the measured boundary conditions for the HTTF tests do not allow to fully validate RELAP5-3D for prismatic HTGR analyses. The authors suspect that some of the differences between predicted and measured temperatures may be a result of uncertainties associated with HTTF itself rather than RELAP5-3D. We demonstrated improved validation for steady-state analysis, but significantly improved transient performance has yet to be recognized.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Electron cyclotron emission measurements and modeling in optically semi-transparent plasma on the HSX stellarator

On the Helically Symmetric Experiment (HSX), electron cyclotron emission (ECE) at the second harmonic of the electron gyrofrequency is measured with a 16-channel heterodyne receiver. An ECE radiometer diagnostic has been calibrated with a broadband frequency source, allowing independent measurements of the electron temperature. The antenna pattern has a significant impact on the measurements, and modeling its effect is necessary to produce an ECE radiation temperature spectrum. Measurements, calibration results, and modeling of the ECE data are presented in this paper. At a relatively high plasma density, HSX plasmas are thermal, and the radiation temperature measured by the radiometer is in good agreement with the electron temperature measured by a Thomson scattering diagnostic. At a relatively low plasma density, the deviation from a Maxwellian distribution is large, and asymmetry in the radiation temperature profile is measured. These measurements are supported by single-pass and multi-pass ray tracing calculations of the electron cyclotron emission using the TRAVIS ray tracing code. Thermal and nonthermal electron populations exist in HSX, and the effect of these populations on the asymmetry in the measured emission is presented.

Cyclotron radiation↗
DOE OSTI2018

Mechanical Properties and Strain-Induced Martensite Transformation in Cold Rolling of 304L Stainless Steel Plate

In this work, cold rolling behavior of stainless steel 304L is investigated and the effects of different process parameters on the occurrence of strain-induced martensite and mechanical properties are studied. The rolling experiments are conducted under different rolling speeds and reductions in which a set of samples is deformed at room temperature and the other set is first cooled to the temperature of − 10 °C and then rolled. Afterward, the developed microstructures and mechanical properties of the rolled steel are evaluated employing different testing techniques. In order to justify the results, mathematical modeling of cold rolling operation is also performed using Abaqus/Explicit to estimate the distribution of equivalent plastic strain and temperature rise during rolling. The results show that strain-induced martensite may occur during cold rolling and it efficiently alters microstructure and mechanical performance of the rolled plate. The amount of reduction, initial temperature, rolling layout, and, to a lesser extent, rolling speed can affect the kinetics of martensite transformation as well as microstructure and mechanical properties of the rolled steel.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Consolidation of iodine-loaded Ag 0 -functionalized silica aerogel with HUP, HIP and SPS

The U.S. Department of Energy is currently investigating alternative sorbents for the removal and immobilization of radioiodine from the gas streams in a nuclear fuel reprocessing plant. One of these new sorbents, silver-functionalized silica aerogel (Ag 0 -aerogel), shows promise as a potential replacement for silver mordenite because of its high selectivity and sorption capacity for iodine. Moreover, a feasible consolidation of iodine-loaded Ag 0 -aerogel to a durable SiO 2 -based waste form makes this aerogel an attractive choice for sequestering radioiodine. The main purpose of the study reported here was to investigate consolidation of Ag 0 -aerogel powders with or without iodine and with or without sintering additives with hot uniaxial pressing (HUP), HIP, and SPS. The selected densified samples were analyzed with a helium gas pycnometer for apparent density, with the Archimedes method for open porosity and apparent density, with scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS) for the extent of densification, macro- and microstructural changes, and distribution of individual elements, and with X-ray diffraction (XRD) for crystalline phases. To convert the iodine-loaded Ag 0 -silica aerogel to a waste form, rapid consolidation with HUP, HIP, and SPS at moderate temperatures and pressures yields a final waste form consisting of AgI particles encapsulated in fused silica. HUP-processing (1200°C for 30 min under 29 MPa pressure) of Ag 0 -aerogel loaded with 20.2 mass% of iodine provided a product with residual open porosity of 16.9%. However, ~93% of sorbed iodine was retained in the sintered material. Densification with HIP at 1200°C for 30 min under 207 MPa pressure resulted in a fully dense silica-based waste form of 3.3 $\times$ 10 3 kg/m 3 bulk density containing ~22 mass% of iodine. Iodine was retained in the form of nano- and micro-inclusions of AgI dispersed in the silica matrix. Additives were not needed to enhance sintering process as depicted from the lack of open porosity and 100% retention of iodine in the consolidated product. The future tests will tell whether additives such as raw silica aerogel or Ag 0 -aerogel are required for HIPing to produce a fully dense waste form from iodine-loaded Ag 0 -aerogel containing higher concentrations of captured iodine. SPS-processing of samples with or without iodine revealed a benefit of additive-enhanced sintering. The samples containing additives (raw silica aerogel, colloidal silica, and Ag 0 -aerogel) shrunk faster and at lower temperatures. In addition, additives significantly improved distribution of silver compounds in the fully densified products, considerably decreasing the number of micron-sized inclusions of AgI, Ag and Ag 2 S at the grain boundaries.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗