Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXTRAPOLATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Evidence of an oxidation induced phase transformation for a delta phase plutonium-gallium alloy

The oxidation of an ~1.5 at% Ga plutonium metal alloy in dry air as a function of time was studied using a combination of FIB-SEM, AES, and XRD. Analysis of SEM images of FIB cross-sections of the oxide allowed for direct measurement of the oxide thickness as well as determination of heterogeneity in the extent of the oxide. AES analysis performed on cross-sections of the oxide allowed for quantitative analysis of the atomic composition and semi-quantitative analysis of the chemical composition. Initial preparation of the sample was found to induce a martensitic transformation to α' - Pu with an average thickness of 233 nm. Electropolishing was found to be sufficient to fully remove the α' layer with creation of only a minimum oxide layer. Growth of the oxide in dry air was found to initially follow parabolic kinetics, with a parabolic rate constant orders of magnitude higher than expected for δ-Pu but in-line with values extrapolated to room temperature for α-Pu. Following complete oxidation of the initial α` layer, further regions of plutonium metal depleted in gallium were observed to form at the oxide / metal interface. However, gallium, as Ga 2 O 3 , was found to be enriched at the surface and present in the oxide in an amount comparable to the relative Ga:Pu ratio of the bulk metal alloy. Finally, the results presented here serve to bridge a diverse array of previous experimental and theoretical data and provide the first comprehensive view of the fate of the δ-stabilizer during formation of an oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Revisiting a minimally destructive analytic approach for determining electrochemical kinetic parameters: Measuring aluminum corrosion across a wide pH range based on the Butler-Volmer equation

Here, this study revisits the three-point sampling of the simplified Butler-Volmer equation to address the limitations of strong potentiodynamic polarization, which can introduce irreversible damage and uncertainty in corrosion analysis. The method extracts electrochemical kinetic parameters while minimizing polarization effects, evaluates noise sensitivity relative to overpotential, and accounts for errors from signal noise, OCP drift, ohmic resistance, and mass-transfer constraints. Verified against the Tafel extrapolation method for aluminum corrosion across a wide pH range, this low-polarization approach enables accurate evaluations with specific error estimates, offering a robust alternative to linear polarization resistance methods that assume constant Tafel slopes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Machine learning in materials research: Developments over the last decade and challenges for the future

The number of studies that apply machine learning (ML) to materials science has been growing at a rate of approximately 1.67 times per year over the past decade. In this review, I examine this growth in various contexts. First, I present an analysis of the most commonly used tools (software, databases, materials science methods, and ML methods) used within papers that apply ML to materials science. The analysis demonstrates that despite the growth of deep learning techniques, the use of classical machine learning is still dominant as a whole. It also demonstrates how new research can effectively build upon past research, particular in the domain of ML models trained on density functional theory calculation data. Next, I present the progression of best scores as a function of time on the matbench materials science benchmark for formation enthalpy prediction. In particular, a dramatic improvement of 7 times reduction in error is obtained when progressing from feature-based methods that use conventional ML (random forest, support vector regression, etc.) to the use of graph neural network techniques. Finally, I provide views on future challenges and opportunities, focusing on data size and complexity, extrapolation, interpretation, access, and relevance.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Projective multiscale time-integration for electrostatic particle-in-cell methods

The simulation of problems in kinetic plasma physics is often challenging due to strongly coupled phenomena across multiple scales. In this work, we propose a wavelet-based coarse-grained numerical scheme, based on the framework of Equation-Free Projective Integration, for a kinetic plasma system modeled by the Vlasov–Poisson equations. A kinetic particle-in-cell (PIC) code is used to simulate the meso scale dynamics for short time intervals. This allows the extrapolation over long time-steps of the behavior of a coarse wavelet-based discretization of the system. To validate the approach and the underlying concepts, we perform two 1D1V numerical experiments: nonlinear propagation and steepening of an ion wave, and the expansion of a plasma slab in vacuum. The direct comparisons to resolved PIC simulations show good agreement. We show that the speedup of the projective integration scheme over the full particle scheme scales linearly with the system size, demonstrating efficiency while taking into account fully kinetic, non-Maxwellian effects. This suggests that the approach is potentially interesting for kinetic plasma problems with a large separation of scales.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

ELSI — An open infrastructure for electronic structure solvers

Routine applications of electronic structure theory to molecules and periodic systems need to compute the electron density from given Hamiltonian and, in case of non-orthogonal basis sets, overlap matrices. System sizes can range from few to thousands or, in some examples, millions of atoms. Different discretization schemes (basis sets) and different system geometries (finite non-periodic vs. infinite periodic boundary conditions) yield matrices with different structures. The ELectronic Structure Infrastructure (ELSI) project provides an open-source software interface to facilitate the implementation and optimal use of high-performance solver libraries covering cubic scaling eigensolvers, linear scaling density-matrix-based algorithms, and other reduced scaling methods in between. In this paper, we present recent improvements and developments inside ELSI, mainly covering (1) new solvers connected to the interface, (2) matrix layout and communication adapted for parallel calculations of periodic and/or spin-polarized systems, (3) routines for density matrix extrapolation in geometry optimization and molecular dynamics calculations, and (4) general utilities such as parallel matrix I/O and JSON output. The ELSI interface has been integrated into four electronic structure code projects (DFTB+, DGDFT, FHI-aims, SIESTA), allowing us to rigorously benchmark the performance of the solvers on an equal footing. Based on results of a systematic set of large-scale benchmarks performed with Kohn–Sham density-functional theory and density-functional tight-binding theory, we identify factors that strongly affect the efficiency of the solvers, and propose a decision layer that assists with the solver selection process. As a result, we describe a reverse communication interface encoding matrix-free iterative solver strategies that are amenable, e.g., for use with planewave basis sets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Local reduced-order modeling for electrostatic plasmas by physics-informed solution manifold decomposition

Despite advancements in high-performance computing and modern numerical algorithms, computational cost remains prohibitive for multi-query kinetic plasma simulations. Here, in this work, we develop data-driven reduced-order models (ROMs) for collisionless electrostatic plasma dynamics, based on the kinetic Vlasov-Poisson equation. Our ROM approach projects the equation onto a linear subspace defined by the proper orthogonal decomposition (POD) modes. We introduce an efficient tensorial method to update the nonlinear term using a precomputed third-order tensor. We capture multiscale behavior with a minimal number of POD modes by decomposing the solution manifold into multiple time windows and creating temporally local ROMs. We consider two strategies for decomposition: one based on the physical time and the other based on the electric field energy. Applied to the 1D1V Vlasov–Poisson simulations, that is, prescribed E-field, Landau damping, and two-stream instability, we demonstrate that our ROMs accurately capture the total energy of the system both for parametric and time extrapolation cases. The temporally local ROMs are more efficient and accurate than the single ROM. In addition, in the two-stream instability case, we show that the energy-windowing reduced-order model (EW-ROM) is more efficient and accurate than the time-windowing reduced-order model (TW-ROM). With the tensorial approach, EW-ROM solves the equation approximately 90 times faster than Eulerian simulations while maintaining a maximum relative error of 7.5% for the training data and 11% for the testing data.

Electrostatic plasmas↗
DOE OSTI2016

Periodic Pulay method for robust and efficient convergence acceleration of self-consistent field iterations

Pulay's Direct Inversion in the Iterative Subspace (DIIS) method is one of the most widely used mixing schemes for accelerating the self-consistent solution of electronic structure problems. In this work, we propose a simple generalization of DIIS in which Pulay extrapolation is performed at periodic intervals rather than on every self-consistent field iteration, and linear mixing is performed on all other iterations. Lastly, we demonstrate through numerical tests on a wide variety of materials systems in the framework of density functional theory that the proposed generalization of Pulay's method significantly improves its robustness and efficiency.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

The hazard components of representative key risks. The physical climate perspective

The framework of Representative Key Risks (RKRs) has been adopted by the Intergovernmental Panel on Climate Change Working Group II in order to categorize, assess and communicate a wide range of regional and sectoral key risks, expected to become severe as a consequence of the potentially detrimental convergence of changing climate conditions, exposure and vulnerability of human and natural systems, and responses through (mal)adaptation measures. Other papers in this special issue treat each of eight RKRs by holistically assessing their current status and future evolution as a result of this convergence. However, their treatment cannot always organize such assessment according to a systematic gradation of climatic changes, often times having to extrapolate the big-picture evolution of risk from either qualitative effects of “low” medium” and “high” warming, or limited/focused analysis of the consequences of particular mitigation choices (e.g., benefits of limiting warming to 1.5 or 2C). In this study we offer as systematic a representation as possible – given current literature and assessments – of the future evolution of the hazard components of RKRs. We draw on the assessment of changes in climatic impact-drivers relevant to RKRs described in the 6th Assessment Report by Working Group 1 (WGI) supplemented when needed by more recent literature. We identify the relevant hazards for each RKR, based upon the WGII authors’ assessment, and we report on their current state and expected future changes in magnitude, intensity and/or frequency, linking these changes to Global Warming Levels to the extent possible. For some of these quantities - like regional trends in oceanic and atmospheric temperature and precipitation, some heat and precipitation extremes, permafrost thaw and Northern Hemisphere snow cover - a strong and quantitative relationship with global average temperature change has been assessed. For others - like frequency and intensity of tropical cyclones and extra-tropical storms, and fire weather - the link to increasing global temperatures can only be described qualitatively. For some processes - like the behavior of ice-sheets, or changes in circulation dynamics - large uncertainties about the effects of different levels of warming remain, and for a few others - like ocean pH and air pollution - the composition of the scenario of anthropogenic emissions is most relevant, rather than the warming reached. In almost all cases, however, the basic message remains that every small increment in CO2 concentration in the atmosphere and associated warming will bring changes in climate phenomena that will contribute to increasing risk of impacts on human and natural systems when these changes happen in conjunction with these systems’ conditions of exposure and vulnerability, and in lack of effective adaptation. Our picture of the evolution of RKR-relevant climatic impact-drivers complements and enriches the treatment of RKRs in the other papers in at least two ways: by filling in an often only cursory or limited representation of the physical climate aspects driving impacts, and by providing a fuller representation of their future possible evolution which represents an important component – if never the only one – of the potential future evolution of risk severity.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Advances in understanding vacuum break dynamics in liquid helium-cooled tubes for accelerator beamline applications

Understanding air propagation and condensation following a catastrophic vacuum break in particle accelerator beamlines cooled by liquid helium is essential for ensuring operational safety. This review summarizes experimental and theoretical work conducted in our cryogenics lab to address this issue. Systematic measurements were performed to study nitrogen gas propagation in uniform copper tubes cooled by both normal liquid helium (He I) and superfluid helium (He II). These experiments revealed a nearly exponential deceleration of the gas front, with stronger deceleration observed in He II-cooled tubes. To interpret these results, a one-dimensional (1D) theoretical model was developed, incorporating gas dynamics, heat transfer, and condensation mechanisms. The model successfully reproduced key experimental observations in the uniform tube system. However, recent experiments involving a bulky copper cavity designed to mimic the geometry of a superconducting radiofrequency (SRF) cavity revealed strong anisotropic flow patterns of nitrogen gas within the cavity, highlighting limitations in extrapolating results from simplified tube geometries to real accelerator beamlines. To address these complexities, we outline plans for systematic studies using tubes with multiple bulky cavities and the development of a two-dimensional (2D) model to simulate gas dynamics in these more intricate configurations. As a result, these efforts aim to provide a comprehensive understanding of vacuum breaks in particle accelerators and improve predictive capabilities for their operational safety.

Beamline tube↗
DOE OSTI2021

High salinity seawater boiling point elevation: Experimental verification

Boiling point elevation (BPE) for high salinity solutions is a crucial parameter that significantly affects the overall thermal efficiency of desalination, water treatment, and many other industrial processing systems, especially when minimum or zero liquid discharge is a key requirement. This paper addresses the discrepancies among the empirical correlations reported in the literature that were commonly used to determine BPE for seawater solutions. An evaluation of the experimental data with low solution concentration reveals that the data cannot be extrapolated to determine the BPE at high concentration (X > 140 ppt or g/kg). Besides, disparities are established within different equations used to determine the BPE for high salinity seawater. As a result of the minimal availability of experimental data of BPE for X > 140 ppt and the need to eliminate the discrepancies, an experimental setup was built, which can produce reliable and repeatable BPE data for any solution concentration. Boiling points were obtained experimentally for seawater solutions with a wide range of salinity (X between 20 and 280 ppt) and brine solution temperature (t b between 20 and 80°C). The experimental results of boiling point elevations for seawater are further compared with the experimental data and analytical results reported in the literature. The newly obtained experimental results show that the minimum and maximum BPE values for the brine solutions tested are 0.175°C at t b = 80°C and X = 20 ppt, and 11.6°C at t b = 80°C and X = 280 ppt, respectively. Furthermore, the measured BPE data for seawater concentration over 80 ppt are fitted and presented using an appropriate fitting model. The new correlation can accurately predict the BPE for high salinity seawater brines and thus should be very helpful in the design of high-energy-efficient evaporation systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Computational flow modeling of triply periodic minimal surfaces as feed channel spacers in ultra-high pressure reverse osmosis applications

Triply periodic minimal surfaces (TPMS) are a special class of mathematical surfaces characterized by a high surface area-to-volume ratio. They have generated considerable interest in fields such as acoustics, heat transfer, and membrane-based filtration processes. This study evaluates the performance of four different TPMS designs—Schoen Gyroid, Schoen Crossed Layers of Parallels (CLP), Schoen Transverse Crossed Layers of Parallels (tCLP), and Schwarz-Primitive—when used as feed channel spacers under ultra-high pressure reverse osmosis (UHPRO) conditions, at approximately 200 bar. Our experimentally validated computational fluid dynamics model reveal different flow patterns within the feed channels for each of the four TPMS designs, leading to varying hydrodynamic and permeation properties. Under the simulated UHPRO conditions, the Gyroid and tCLP designs yield up to a 23% increase in average permeate velocity and a 14% reduction in average membrane-surface concentration relative to a non-woven spacer of the same porosity. Furthermore, the enhanced performance comes with an increased feed channel pressure drop, although it only constitutes less than 4% of the operating pressure when extrapolated for a meter-long membrane module. Additionally, the study analyzes the effects of varying inlet velocity and spacer porosity on membrane performance. Overall, this research provides valuable insights into the potential use of TPMS spacers in UHPRO applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AI-based language models powering drug discovery and development

The discovery and development of new medicines is expensive, time-consuming, and often inefficient, with many failures along the way. Powered by artificial intelligence (AI), language models (LMs) have changed the landscape of natural language processing (NLP), offering possibilities to transform treatment development more effectively. Here, we summarize advances in AI-powered LMs and their potential to aid drug discovery and development. We highlight opportunities for AI-powered LMs in target identification, clinical design, regulatory decision-making, and pharmacovigilance. We specifically emphasize the potential role of AI-powered LMs for developing new treatments for Coronavirus 2019 (COVID-19) strategies, including drug repurposing, which can be extrapolated to other infectious diseases that have the potential to cause pandemics. Finally, we set out the remaining challenges and propose possible solutions for improvement.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Nuclear microreactor transient and load-following control with deep reinforcement learning

The economic feasibility of nuclear microreactors will depend on minimizing operating costs through advancements in autonomous control, especially when these microreactors are operating alongside other types of energy systems (e.g., renewable energy). This study explores the application of deep reinforcement learning (RL) for real-time drum control in microreactors, exploring performance in regard to load-following scenarios. By leveraging a point kinetics model with thermal and xenon feedback, we first establish a baseline using a single-output RL agent, then compare it against a traditional proportional–integral–derivative (PID) controller. This study demonstrates that RL controllers, including both single- and multi-agent RL (MARL) frameworks, can achieve similar or even superior load-following performance as traditional PID control across a range of load-following scenarios. In short transients, the RL agent was able to reduce the tracking error rate in comparison to PID by one half to one third. Over extended 300-minute load-following scenarios in which xenon feedback becomes a dominant factor, PID maintained better accuracy, but RL still remained within a 1% error margin despite being trained only on short-duration scenarios. This highlights RL’s strong ability to generalize and extrapolate to longer, more complex transients, affording substantial reductions in training costs and reduced overfitting. Furthermore, when control was extended to multiple drums, MARL enabled independent drum control as well as maintained reactor symmetry constraints without sacrificing performance---an objective that standard single-agent RL could not learn. We also found that, as increasing levels of Gaussian noise were added to the power measurements, the RL controllers were able to maintain lower error rates than PID, and to do so with at least 10% and upwards of 150% less control effort. These findings illustrate RL's potential for autonomous nuclear reactor control, laying the groundwork for future integration into high-fidelity simulations and experimental validation efforts.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2013

The role of Health Impact Assessment in the setting of air quality standards: An Australian perspective

The approaches used for setting or reviewing air quality standards vary from country to country. The purpose of this research was to consider the potential to improve decision-making through integration of HIA into the processes to review and set air quality standards used in Australia. To assess the value of HIA in this policy process, its strengths and weaknesses were evaluated aligned with review of international processes for setting air quality standards. Air quality standard setting programmes elsewhere have either used HIA or have amalgamated and incorporated factors normally found within HIA frameworks. They clearly demonstrate the value of a formalised HIA process for setting air quality standards in Australia. The following elements should be taken into consideration when using HIA in standard setting. (a) The adequacy of a mainly technical approach in current standard setting procedures to consider social determinants of health. (b) The importance of risk assessment criteria and information within the HIA process. The assessment of risk should consider equity, the distribution of variations in air quality in different locations and the potential impacts on health. (c) The uncertainties in extrapolating evidence from one population to another or to subpopulations, especially the more vulnerable, due to differing environmental factors and population variables. (d) The significance of communication with all potential stakeholders on issues associated with the management of air quality. In Australia there is also an opportunity for HIA to be used in conjunction with the NEPM to develop local air quality standard measures. The outcomes of this research indicated that the use of HIA for air quality standard setting at the national and local levels would prove advantageous. -- Highlights: • Health Impact Assessment framework has been applied to a policy development process. • HIA process was evaluated for application in air quality standard setting. • Advantages of HIA in the air quality standard setting process are demonstrated.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2015

Sustainability on the urban scale: Proposal of a structure of indicators for the Spanish context

Some efforts to assess sustainability on the urban scale have been made and different tools for measuring the impact on and caused by cities have emerged. However, the sustainability concept varies from region to region, and indicators to measure it should be suitable for the context-specific conditions of the region under study. After doing a comprehensive review of the indicators included in 13 tools developed to assess urban sustainability of cities, this article proposes a new structure of indicators adapted to a Mediterranean city in Spain. The proposed structure is based on a two-level scheme that consists in 14 categories and 63 subcategories, which agglutinate urban sustainability indicators according to their purpose. This structure suggests a set of comprehensible qualitative and quantitative indicators that are easily applicable on neighbourhood or city scales. Given the similar features of Mediterranean countries in terms of environmental and socio-economic aspects, the proposed structure could be extrapolated to other countries with climatic and cultural similarities. Otherwise, the system is a useful tool in the decision-making process to help the different stakeholders involved in new urban developments and regeneration projects in existing neighbourhoods, such as developers, urban planners and public administrations. - Highlights: • Comprehensive review of 13 urban sustainability assessment tools • Proposal of a two-level structure to cluster urban sustainability indicators • Inclusion of sustainability criteria for urban planning projects and interventions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2015

A European Sustainable Tourism Labels proposal using a composite indicator

The tourism sector in Europe faces important challenges which it must deal with to promote its future development. In this context, the European Commission considers that two key issues must be addressed. On the one hand, a better base of socio-economic knowledge about tourism and its relationship with the environment is needed, and, on the other hand, it is necessary to improve the image of European areas as quality sustainable tourism destinations. In this paper we present analytical tools that cover these needs. Specifically, we define a system of sustainable tourism indicators and we obtain a composite indicator incorporating weights quantified using a panel of experts. Employing the values of this global indicator as a basis, we define a Sustainable Tourism Country-Brand Ranking which assesses the perception of each country-brand depending on its degree of sustainability, and a system of sustainable tourism labels which reward the management carried out. - Highlights: • We define a system of indicators to improve the knowledge about sustainable tourism. • We obtain composite indicators based on expert knowledge. • The Sustainable Tourism Country-Brand Ranking would improve the image of destinations. • We define a Sustainable Tourism Labels System to assess country-brands. • The conclusions of the empirical analysis can be extrapolated to other tourist areas.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Environmental impact assessment of online advertising

Highlights: • A practical framework for assessing the environmental impact of any Internet service • Online advertising consumed between 20.38 to 282.75 TWh of energy and 11.53 – 159.93 million tons of CO{sub 2}e was emitted to produce the electricity consumed. • Invalid traffic associated with online advertising resulted in 2.65 – 36.78 million tons of CO{sub 2}e emissions. • The energy burden of online advertising is considerable and urgently requires attention from researchers and industries. - Abstract: There are no commonly agreed ways to assess the total energy consumption of the Internet. Estimating the Internet's energy footprint is challenging because of the interconnectedness associated with even seemingly simple aspects of energy consumption. The first contribution of this paper is a common modular and layered framework, which allows researchers to assess both energy consumption and CO{sub 2}e emissions of any Internet service. The framework allows assessing the energy consumption depending on the research scope and specific system boundaries. Further, the proposed framework allows researchers without domain expertise to make such an assessment by using intermediate results as data sources, while analyzing the related uncertainties. The second contribution is an estimate of the energy consumption and CO{sub 2}e emissions of online advertising by utilizing our proposed framework. The third contribution is an assessment of the energy consumption of invalid traffic associated with online advertising. The second and third contributions are used to validate the first. The online advertising ecosystem resides in the core of the Internet, and it is the sole source of funding for many online services. Therefore, it is an essential factor in the analysis of the Internet's energy footprint. As a result, in 2016, online advertising consumed 20–282 TWh of energy. In the same year, the total infrastructure consumption ranged from 791 to 1334 TWh. With extrapolated 2016 input factor values without uncertainties, online advertising consumed 106 TWh of energy and the infrastructure 1059 TWh. With the emission factor of 0.5656 kg CO{sub 2}e/kWh, we calculated the carbon emissions of online advertising, and found it produces 60 Mt CO{sub 2}e (between 12 and 159 Mt of CO{sub 2}e when considering uncertainty). The share of fraudulent online advertising traffic was 13.87 Mt of CO{sub 2}e emissions (between 2.65 and 36.78 Mt of CO{sub 2}e when considering uncertainty). The global impact of online advertising is multidimensional. Online advertising affects the environment by consuming significant amounts of energy, leading to the production CO{sub 2}e emissions. Hundreds of billions of ad dollars are exchanged yearly, placing online advertising in a significant role economically. It has become an important and acknowledged component of the online-bound society, largely due to its integration with the Internet and the amount of revenue generated through it.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2014

Occupancy schedules learning process through a data mining framework

Building occupancy is a paramount factor in building energy simulations. Specifically, lighting, plug loads, HVAC equipment utilization, fresh air requirements and internal heat gain or loss greatly depends on the level of occupancy within a building. Developing the appropriate methodologies to describe and reproduce the intricate network responsible for human-building interactions are needed. Extrapolation of patterns from big data streams is a powerful analysis technique which will allow for a better understanding of energy usage in buildings. A three-step data mining framework is applied to discover occupancy patterns in office spaces. First, a data set of 16 offices with 10 minute interval occupancy data, over a two year period is mined through a decision tree model which predicts the occupancy presence. Then a rule induction algorithm is used to learn a pruned set of rules on the results from the decision tree model. Finally, a cluster analysis is employed in order to obtain consistent patterns of occupancy schedules. Furthermore, the identified occupancy rules and schedules are representative as four archetypal working profiles that can be used as input to current building energy modeling programs, such as EnergyPlus or IDA-ICE, to investigate impact of occupant presence on design, operation and energy use in office buildings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗