Search NASA⌕ Search

SEARCH · Search NASA

Results for “Homogeneous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Experimental investigation on pulverized coal reburning crucially related with its ignition mode

Experimental investigation on reburning by a pulverized bituminous coal was performed in a one-dimensional flow reactor, in which the ignition statuses of the coal were monitored by on-line gas analysis, solid sampling, and direct image acquisition. The experimental results indicate that NO reduction efficiency (RE) varies nonmonotonically with stoichiometric ratio of oxygen to coal (SR) entering the reburning zone: the lower SR does not necessarily result in the higher RE, mainly due to the great influence of ignition modes of the coal. Before ignition, RE increases with increasing SR, since a little oxygen is in favor of homogeneous NO reduction. Then, RE decreases greatly after homogeneous ignition with increase of SR, due to the rapid consumption of NO-reducing species by the volatile flame in the boundary layer of the particle, before going to the flue gas for NO reduction. When the joint heterohomogeneous ignition happens with further increase of SR, the char temperature increases violently, the heterogeneous NO reduction rate rises obviously with increasing temperature, then the whole RE begins to increase again. As a result of even higher SR, the char combustion is controlled by diffusion, and it is difficult for the oxygen necessary for heterogeneous NO reduction reactions to reach the surface, then the RE decreases again. The promotion effects of char ignition on RE are more obvious at lower temperature in the reburning zone, and the SR values at which the above relevant phenomena appear are lower for coarser coal particles. 36 refs., 7 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Revealing the location and structure of the accretion disk wind in PDS 456

We present evidence for the rapid variability of the high-velocity iron K-shell absorption in the nearby (z = 0.184) quasar PDS 456. From a recent long Suzaku observation in 2013 (∼1 Ms effective duration), we find that the equivalent width of iron K absorption increases by a factor of ∼5 during the observation, increasing from <105 eV within the first 100 ks of the observation, toward a maximum depth of ∼500 eV near the end. The implied outflow velocity of ∼0.25 c is consistent with that claimed from earlier (2007, 2011) Suzaku observations. The absorption varies on timescales as short as ∼1 week. We show that this variability can be equally well attributed to either (1) an increase in column density, plausibly associated with a clumpy time-variable outflow, or (2) the decreasing ionization of a smooth homogeneous outflow which is in photo-ionization equilibrium with the local photon field. The variability allows a direct measure of absorber location, which is constrained to within r = 200-3500 r {sub g} of the black hole. Even in the most conservative case, the kinetic power of the outflow is ≳ 6% of the Eddington luminosity, with a mass outflow rate in excess of ∼40% of the Eddington accretion rate. The wind momentum rate is directly equivalent to the Eddington momentum rate which suggests that the flow may have been accelerated by continuum scattering during an episode of Eddington-limited accretion.

79 ASTRONOMY AND ASTROPHYSICS↗

The local wavenumber model for computation of turbulent mixing

We present an overview of the current status in the development of a two-point spectral closure model for turbulent flows, known as the local wavenumber (LWN) model. The model is envisioned as a practical option for applications requiring multi-physics simulations in which statistical hydrodynamics quantities such as Reynolds stresses, turbulent kinetic energy, and measures of mixing such as density-correlations and mix-width evolution, need to be captured with relatively high fidelity. In this review, we present the capabilities of the LWN model since it was first formulated in the early 1990s, for computations of increasing levels of complexity ranging from homogeneous isotropic turbulence, inhomogeneous and anisotropic single-fluid turbulence, to two-species mixing driven by buoyancy forces. The review concludes with a discussion of some of the more theoretical considerations that remain in the development of this model.

42 ENGINEERING↗

Novel Anionic Clay Adsorbents for Boiler-Blow-Down Waters Reclaim and Reuse

Arsenic (As) and Selenium (Se) are found in water in the form of oxyanions. Relatively high concentrations of As and Se have been reported both in power plant discharges, as well as, in fresh water supplies. The International Agency for Research on Cancer currently classifies As as a group 1 chemical, that is considered to be carcinogenic to humans. In Phase I of this project we studied the adsorption of As and Se by uncalcined and calcined layered double hydroxide (LDH). The focus of the present work is a systematic study of the adsorption of As and Se by conditioned LDH adsorbents. Conditioning the adsorbent significantly reduced the Mg and Al dissolution observed with uncalcined and calcined LDH. The adsorption rates and isotherms have been investigated in batch experiments using particles of four different particle size ranges. As(V) adsorption is shown to follow a Sips-type adsorption isotherm. The As(V) adsorption rate on conditioned LDH increases with decreasing adsorbent particle size; the adsorption capacity, on the other hand, is independent of the particle size. A homogeneous surface diffusion model (HSDM) and a bi-disperse pore model (BPM) - the latter viewing the LDH particles as assemblages of microparticles and taking into account bulk diffusion in the intraparticle pore space, and surface diffusion within the microparticles themselves - were used to fit the experimental kinetic data. The HSDM estimated diffusivity values dependent on the particle size, whereas the BPM predicted an intracrystalline diffusivity, which is fairly invariant with particle size. The removal of As(V) on conditioned LDH adsorbents was also investigated in flow columns, where the impact of important solution and operational parameters such as influent As concentration, pH, sorbent particle size and flow rate were studied. An early breakthrough and saturation was observed at higher flow rates and at higher influent concentrations, whereas a decrease in the sorbent particle size and a decrease in influent pH resulted in an increase in the bed volumes treated at breakthrough. Both the HSDM and BPM were shown capable of predicting the column behavior.

20 FOSSIL-FUELED POWER PLANTS↗

The Geology of East Butte, a Rhyolitic Volcanic Dome on the Eastern Snake River Plain, Idaho

East Butte is a prominent volcanic dome located on the eastern Snake River Plain. It is situated 51 km west of Idaho Fallls in the southeast corner of the Idaho National Engineering facility. East Butte rises 350 meters above the Quaternary basalt flows which encircle its 2.4 kilometer diameter base. Its maximum elevation is 2003 meters above sea level. East Butte is composed dominantly of rhyolite. Armstrong and others (1975) determined a K-Ar age of 0.6 +/- m.y. for a rhyolite sample from East Butte. Detailed geologic mapping revealed East Butte to be a single, large cumulo-dome composed dominantly of rhyolite. Major element geochemical analyses indicate that the rhyolite of East Butte is mildly peralkaline (molecular excess of Na2O and K2O over Al2O3 and compositionally homogeneous. Color variations in the East Butte rhyolite result from varying amounts of chemical and physical weathering and to the degree of devitrification that the glass in the groundmass of the rhyolite underwent.

Bretches, J. E.↗

Traveling Magnetic Field Applications for Materials Processing in Space

Including the capability to induce a controlled fluid flow in the melt can significantly enrich research on solidification phenomena in a microgravity environment. The traveling magnetic field (TMF) is a promising technique to achieve this goal and is the aim of our ground-based project. In this presentation we will discuss new theoretical as well as experimental results recently obtained by our group. In particular, we experimentally demonstrated efficient mixing of metal alloys in long tubes subjected to TMF during processing. Application of this technique can provide an elegant solution to ensure melt homogenization prior to solidification in a microgravity environment where natural convection is generally absent. Results of our experimental work of applying the TMF technique to alloy melts will be presented. Possible applications of TMF on board the International Space Station will also be discussed.

Grugel, R. N.↗

Analysis of calibration materials to improve dual-energy CT scanning for petrophysical applications

Dual energy CT-scanning is a rapidly emerging imaging technique employed in non-destructive evaluation of various materials. Although CT (Computerized Tomography) has been used for characterizing rocks and visualizing and quantifying multiphase flow through rocks for over 25 years, most of the scanning is done at a voltage setting above 100 kV for taking advantage of the Compton scattering (CS) effect, which responds to density changes. Below 100 kV the photoelectric effect (PE) is dominant which responds to the effective atomic numbers (Zeff), which is directly related to the photo electric factor. Using the combination of the two effects helps in better characterization of reservoir rocks. The most common technique for dual energy CT-scanning relies on homogeneous calibration standards to produce the most accurate decoupled data. However, the use of calibration standards with impurities increases the probability of error in the reconstructed data and results in poor rock characterization. This work combines ICP-OES (inductively coupled plasma optical emission spectroscopy) and LIBS (laser induced breakdown spectroscopy) analytical techniques to quantify the type and level of impurities in a set of commercially purchased calibration standards used in dual-energy scanning. The Zeff data on the calibration standards with and without impurity data were calculated using the weighted linear combination of the various elements present and used in calculating Zeff using the dual energy technique. Results show 2 to 5% difference in predicted Zeff values which may affect the corresponding log calibrations. The effect that these techniques have on improving material identification data is discussed and analyzed. The workflow developed in this paper will translate to a more accurate material identification estimates for unknown samples and improve calibration of well logging tools.

42 ENGINEERING↗

Submarine record of volcanic island construction and collapse in the Lesser Antilles arc: First scientific drilling of submarine volcanic island landslides by IODPExpedition 340

IODP Expedition 340 successfully drilled a series of sites offshore Montserrat, Martinique and Dominica in the Lesser Antilles from March to April 2012. These are among the few drill sites gathered around volcanic islands, and the first scientific drilling of large and likely tsunamigenic volcanic island-arc landslide deposits. These cores provide evidence and tests of previous hypotheses for the composition and origin of those deposits. Sites U1394, U1399, and U1400 that penetrated landslide deposits recovered exclusively seafloor sediment, comprising mainly turbidites and hemipelagic deposits, and lacked debris avalanche deposits. This supports the concepts that i/ volcanic debris avalanches tend to stop at the slope break, and ii/ widespread and voluminous failures of preexisting low-gradient seafloor sediment can be triggered by initial emplacement of material from the volcano. Offshore Martinique (U1399 and 1400), the landslide deposits comprised blocks of parallel strata that were tilted or microfaulted, sometimes separated by intervals of homogenized sediment (intense shearing), while Site U1394 offshore Montserrat penetrated a flat-lying block of intact strata. The most likely mechanism for generating these large-scale seafloor sediment failures appears to be propagation of a decollement from proximal areas loaded and incised by a volcanic debris avalanche. These results have implications for the magnitude of tsunami generation. Under some conditions, volcanic island landslide deposits composed of mainly seafloor sediment will tend to form smaller magnitude tsunamis than equivalent volumes of subaerial block-rich mass flows rapidly entering water. Expedition 340 also successfully drilled sites to access the undisturbed record of eruption fallout layers intercalated with marine sediment which provide an outstanding high-resolution data set to analyze eruption and landslides cycles, improve understanding of magmatic evolution as well as offshore sedimentation processes.

58 GEOSCIENCES↗

Experimental Determination of the Relationship Between Organic Aerosol Viscosity and Ice Nucleation at Upper Free Tropospheric Conditions

Abstract This work presents measurements of the ice nucleating ability of secondary organic material recorded between −40 and −70°C and relative humidity with respect to ice (RH ice ) between 150% and 220%. For a subset of systems, temperature and humidity dependence of particle viscosity as well as dry glass transition temperature were characterized using the dual tandem differential mobility analyzer method. Eleven unique monoterpene, sesquiterpene and aromatic precursors were used to generate secondary organic material (SOM) using either an oxidation flow reactor (OFR) or an environmental chamber (EC). For the SOM for which viscosity was measured, the particle glass transition temperatures varied between 6 and 23°C ( n = 8). Measurements were performed to verify that increased relative humidity did not plasticize the particles below −10°C at residence times similar to those in the ice nucleation instrument. No heterogeneous ice nucleation was observed at the ∼0.5% onset threshold for any of the materials generated. The ice nucleation occurs by the freezing of SOM solution droplets consistent with homogeneous freezing indicating that they form an aqueous solution, or the SOM particles required water saturation to freeze, indicating that they were hydrophobic. Experiments exploring the influence of functional groups and mass loading did not reveal any obvious influence of particle chemistry or generation conditions on the results. Close structural matches between known organic ice nucleating particles as precursor or formed products did not yield materials that promoted freezing. These experiments suggest that heterogeneous ice formation of glassy secondary organic materials is likely uncommon under upper free tropospheric conditions.

54 ENVIRONMENTAL SCIENCES↗

Simulation and demonstration of magnetohydrodynamic energy conversion in a high-temperature inert gas

The present paper describes high-density magnetohydrodynamic (MHD) energy conversion in a high-temperature seed-free argon plasma, for which a quasi-three-dimensional numerical simulation and a single-pulse shock-tunnel-based demonstration are conducted. The numerical model simulates the two-dimensional profiles of both the electron and the heavy-particle system of the supersonic argon plasma flow, of which the total inflow temperature is 8000 K. The MHD power-generating experiment clarifies the relationship between the plasma quality and the energy conversion efficiency as functions of the total inflow temperature (7600-9600 K) and the applied magnetic flux density (up to 4.0 T). The increase in the total inflow temperature from 7600 to 9400 K and the application of magnetic flux with density of 0.5-1.2 T change the plasma state; unstable behavior accompanied by an inhomogeneous structure is transformed to a homogeneous and stable state, which results in the significant improvement of the power generation performance. Even in low-density magnetic flux, the attained generator performance is comparable or superior to previous results obtained using a conventional low-temperature seeded gas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multi-temperature model derived from state-to-state kinetics for hypersonic entry in Jupiter atmosphere

A state-to-state model of H{sub 2}/He plasmas coupling the master equations for internal distributions of heavy species with the transport equation for the free electrons has been used as a basis for implementing a multi-temperature kinetic model. In the multi-temperature model internal distributions of heavy particles are Boltzmann, the electron energy distribution function is Maxwell, and the rate coefficients of the elementary processes become a function of local temperatures associated to the relevant equilibrium distributions. The state-to-state and multi-temperature models have been compared in the case of a homogenous recombining plasma, reproducing the conditions met during supersonic expansion though converging-diverging nozzles.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

To Produce Nutrients for Plant Growth

On July 1, 1979 a new research program entitled "Development of a Prototype Experiment for Treating CELSS and PCELSS Wastes to Produce Nutrients for Plant Growth" was undertaken by the Massachusetts Institute of Technology and the Georgia Institute of Technology under grant from the National Aeronautics and Space Administration's Ames Research Center. The program was designed to be completed over a five-year period, with the work divided into two phases. Phase I covers approximately two years and involves the development of necessary facilities, chemical methodologies and models to allow meaningful experiments during Phase II, which will involve interfacing waste oxidation with plant growth. Homogeneous samples of freeze-dried human feces and urine have been prepared to assure comparability of results among various CELSS waste treatment research groups. A model of food processing wastes within a PCELSS was developed, and an initial batch of waste was prepared. An automated gas chromatographic system to analyze oxidizer effluents was designed and is operational. A state-of-the-art quantitative elemental analysis capability, built around inductively coupled plasma emission spectroscopy and atomic absorption spectroscopy using electrothermal atomization, has been demonstrated. A continuous flow wet oxidation system was constructed and is now operational.

Michael Modell↗

On the Subgrid-Scale Modeling of Compressible Turbulence

A new sub-grid scale model is presented for the large-eddy simulation of compressible turbulence. In the proposed model, compressibility contributions have been incorporated in the sub-grid scale eddy viscosity which, in the incompressible limit, reduce to a form originally proposed by Smagorinsky (1963). The model has been tested against a simple extension of the traditional Smagorinsky eddy viscosity model using simulations of decaying, compressible homogeneous turbulence. Simulation results show that the proposed model provides greater dissipation of the compressive modes of the resolved-scale velocity field than does the Smagorinsky eddy viscosity model. For an initial r.m.s. turbulence Mach number of 1.0, simulations performed using the Smagorinsky model become physically unrealizable (i.e., negative energies) because of the inability of the model to sufficiently dissipate fluctuations due to resolved scale velocity dilations. The proposed model is able to provide the necessary dissipation of this energy and maintain the realizability of the flow. Following Zeman (1990), turbulent shocklets are considered to dissipate energy independent of the Kolmogorov energy cascade. A possible parameterization of dissipation by turbulent shocklets for Large-Eddy Simulation is also presented.

Squires, Kyle↗

Mild-to-wild plastic transition is governed by athermal screw dislocation slip in bcc Nb

Plastic deformation in crystals is mediated by the motion of line defects known as dislocations. For decades, dislocation activity has been treated as a homogeneous, smooth continuous process. However, it is now recognized that plasticity can be determined by long-range correlated and intermittent collective dislocation processes, known as avalanches. Here we demonstrate in body-centered cubic Nb how the long-range and scale-free dynamics at room temperature are progressively quenched out with decreasing temperature, eventually revealing intermittency with a characteristic length scale that approaches the Burgers vector itself. Plasticity is shown to be bimodal across the studied temperature regime, with conventional thermally-activated smooth plastic flow (‘mild’) coexisting with sporadic bursts (‘wild’) controlled by athermal screw dislocation activity, thereby violating the classical notion of temperature-dependent screw dislocation motion at low temperatures. An abrupt increase of the athermal avalanche component is identified at the critical temperature of the material. Our results indicate that plasticity at any scale can be understood in terms of the coexistence of these mild and wild modes of deformation, which could help design better alloys by suppressing one of the two modes in desired temperature windows.

36 MATERIALS SCIENCE↗

Evolution of the Surface Science of Catalysis from Single Crystals to Metal Nanoparticles under Pressure

Vacuum studies of metal single crystal surfaces using electron and molecular beam scattering revealed that the surface atoms relocate when the surface is clean (reconstruction) and when it is covered by adsorbates (adsorbate induced restructuring). It was also discovered that atomic steps and other low coordination surface sites are active for breaking chemical bonds (H-H, O=O, C-H, C=O and C-C) with high reaction probability. Investigations at high reactant pressures using sum frequency generation (SFG)--vibrational spectroscopy and high pressure scanning tunneling microscopy (HPSTM) revealed bond breaking at low reaction probability sites on the adsorbate-covered metal surface, and the need for adsorbate mobility for continued turnover. Since most catalysts (heterogeneous, enzyme and homogeneous) are nanoparticles, colloid synthesis methods were developed to produce monodispersed metal nanoparticles in the 1-10 nm range and controlled shapes to use them as new model catalyst systems in two-dimensional thin film form or deposited in mesoporous three-dimensional oxides. Studies of reaction selectivity in multipath reactions (hydrogenation of benzene, cyclohexene and crotonaldehyde) showed that reaction selectivity depends on both nanoparticle size and shape. The oxide-metal nanoparticle interface was found to be an important catalytic site because of the hot electron flow induced by exothermic reactions like carbon monoxide oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extreme nonlinear electrodynamics in metamaterials with very small linear dielectric permittivity

We consider a subwavelength periodic layered medium whose slabs are filled by arbitrary linear metamaterials and standard nonlinear Kerr media and show that the homogenized medium behaves as a Kerr medium whose parameters can assume values not available in standard materials. Exploiting such a parameter availability, we focus on the situation where the linear relative dielectric permittivity is very small, thus allowing the observation of the extreme nonlinear regime where the nonlinear polarization is comparable with or even greater than the linear part of the overall dielectric response. The behavior of the electromagnetic field in the extreme nonlinear regime is very peculiar and characterized by interesting features such as the transverse power flow reversing. In order to probe this regime, we consider a class of fields (transverse magnetic nonlinear guided waves) admitting full analytical description and show that these waves are allowed to propagate even in media with {epsilon}<0 and {mu}>0 since the nonlinear polarization produces a positive overall effective permittivity. The considered nonlinear waves exhibit, in addition to the mentioned features, a number of interesting properties like hyperfocusing induced by the phase difference between the field components.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Internal structures of the Galilean satellites

Models for the interior structures of Io, Ganymede and Callisto are proposed based on recent discoveries of volcanism and high heat flow on Io, a primordial, heavily cratered surface on Callisto, and a surface modified by endogenic processes on Ganymede. The model for Io consists of a thin, high-rigidity outer shell overlying a thin, partially molten or molten layer maintained by tidal dissipation in the outer shell, which in turn surrounds a solid interior. Ganymede is modeled as an ice outer layer surrounding a shell of undifferentiated, primordial ice-silicate mixture and a rock core, with accretional heating responsible for melting the ice in an originally homogeneous ice-silicate interior. Finally, the old, heavily cratered surface of Callisto is interpreted as suggesting a primordial ice-silicate mixture with little, if any, ice-rock differentiation in the interior.

Schubert, G.↗

Dynamics of flux tubes in accretion disks

The study of magnetized plasmas in astrophysics is complicated by a number of factors, not the least of which is that in considering magnetic fields in stars or accretion disks, we are considering plasmas with densities well above those we can study in the laboratory. In particular, whereas laboratory plasmas are dominated by the confining magnetic field pressure, stars, and probably accretion disks, have magnetic fields whose beta (ratio of gas pressure to magnetic field pressure) is much greater than 1. Observations of the Sun suggest that under such circumstances the magnetic field breaks apart into discrete flux tubes with a small filling factor. On the other hand, theoretical treatments of MHD turbulence in high-beta plasmas tend to assume that the field is more or less homogeneously distributed throughout the plasma. Here we consider a simple model for the distribution of magnetic flux tubes in a turbulent medium. We discuss the mechanism by which small inhomogeneities evolve into discrete flux tubes and the size and distribution of such flux tubes. We then apply the model to accretion disks. We find that the fibrilation of the magnetic field does not enhance magnetic buoyancy. We also note that the evolution of an initially diffuse field in a turbulent medium, e.g., any uniform field in a shearing flow, will initially show exponential growth as the flux tubes form. This growth saturates when the flux tube formation is complete and cannot be used as the basis for a self-sustaining dynamo effect. Since the typical state of the magnetic field is a collection of intense flux tubes, this effect is of limited interest. However, it may be important early in the evolution of the galactic magnetic field, and it will play a large role in numerical simulations. Finally, we note that the formation of flux tubes is an essential ingredient in any successful dynamo model for stars or accretion disks.

Vishniac, E. T.↗