Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lattice optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline type-I Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) clathrates prepared by combining arc melting and spark plasma sintering methods

The gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) compounds with the type-I clathrate structure is presented. Samples were prepared by combining arc melting and spark plasma sintering methods. Powder x-ray diffraction, Rietveld analysis, scanning electron microscopy, and energy-dispersive x-ray spectroscopy show that the solubility limit of gallium in the type-I clathrate phase is close to x=15, which is slightly higher than that for a single crystal. The carrier concentration at room temperature decreases from 2 Multiplication-Sign 10{sup 21} cm{sup -3} to 4 Multiplication-Sign 10{sup 20} cm{sup -3} as the Ga content x increases. The Seebeck coefficient, the electrical conductivity, and the thermal conductivity vary systematically with the carrier concentration when the Ga content x varies. The effective mass (2.0m{sub 0}), the carrier mobility (10 cm{sup 2} V{sup -1} s{sup -1}), and the lattice thermal conductivity (1.1 W m{sup -1} K{sup -1}) are determined for the Ga content x=14.51. The dimensionless thermoelectric figure of merit ZT is about 0.55 at 900 K for the Ga content x=14.51. The calculation of ZT using the experimentally determined material parameters predicts ZT=0.8 (900 K) at the optimum carrier concentration of about 2 Multiplication-Sign 10{sup 20} cm{sup -3}. - Graphical abstract: The gallium composition dependence of crystallographic and thermoelectric properties is presented on polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} with the type-I clathrate structure prepared by combining arc melting and spark plasma sintering methods. The thermoelectric figure of merit ZT reaches 0.55 at 900 K due to the increase in the Ga content (close to x=15), and a calculation predicts further improvement of ZT at the optimized carrier concentration. Highlights: Black-Right-Pointing-Pointer Crystallographic properties of Ba{sub 8}Ga{sub x}Si{sub 46-x} clathrates are characterized. Black-Right-Pointing-Pointer Arc melting and spark plasma sintering process enables increase of Ga content. Black-Right-Pointing-Pointer We elucidate the Ga composition dependence of thermoelectric properties. Black-Right-Pointing-Pointer Thermoelectric figure of merit ZT is improved due to the increased Ga content. Black-Right-Pointing-Pointer Calculation predicts a potential ZT=0.8 at 900 K at optimized carrier concentration.

36 MATERIALS SCIENCE↗

Synthesis and Microstructural Analysis of Magnetic CaFe{sub 0.5}Co{sub 0.5}O{sub 3−δ} Using Rietveld Method

Perovskite cobaltates are widely recognized as potential candidates for their applications in magnetic and magnetoresistive applications. In this report, pseudo-magnetic CaFe{sub 0.5}Co{sub 0.5}O{sub 3−δ} was synthesized at ambient pressure. Various calcinations, heating times, and sintering temperatures were applied in order to achieve the optimized conditions. The optimal sintering temperature with excellent phase and microstructure was found at ∼1050 °C using CaCO{sub 3} as precursor. Rietveld analysis was carried out to solve and refine the XRD pattern of the final specimens. The sample with excellent refined values was solved in orthorhombic phase and pbcm space group. From the SEM and EDS analysis, the excellent grain growth with high densification and ABO{sub 3} structure was confirmed respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic, magnetic, and optical properties of bulk and (1 1 1)-surfaces of CoMnZnSi quaternary Heusler alloy

The structural stability, electronic structure, and magnetic and optical properties of CoMnZnSi quaternary Heusler alloy (QHA) in the bulk and (1 1 1)-slab forms have been investigated by performing density functional theory (DFT) calculations. Formation and cohesive energies, and elastic constants confirm that the bulk CoMnZnSi is chemically and mechanically stable at an equilibrium lattice parameter of 5.81 Å. The calculated elastic constants also indicate that this QHA has ductile and anisotropic features. We investigate and discuss the bonding behavior from charge density distribution and density of states. Furthermore, these calculations in the bulk phase show a perfect half-metallic behavior with an integer value of magnetic moment (4 µB) and a large spin-flip gap of 0.39 eV. On the other hand, the Co (1 1 1) and Si (1 1 1)-slabs exhibit semi-metallic nature at the Fermi level. These results indicate that CoMnZnSi qualifies for spintronic applications. In the bulk and Co (1 1 1), Zn (1 1 1), and Si (1 1 1)-surfaces, the magnetic moment of Co and Mn atoms are ferromagnetically aligned, while the ferrimagnetic alignment of Co with Mn has been found in Mn (1 1 1)-surface. We also investigate the optimal conductivity, dielectric functions, reflectivity, absorption coefficient, refractive index, and loss function to understand the underlying optical properties of this alloy.

36 MATERIALS SCIENCE↗

Mechanistic origins of excitonic properties in 2D perovskites: Implications for exciton engineering

As the field of 2D halide perovskites (HPs) matures, state-of-the-art techniques to measure important properties, such as the band gap (E g ) and exciton binding energy (E b ), continue to produce inconsistent values. Here, we tackle this long-standing problem by obtaining direct measurements of E g and E b for 31 unique HP structures. The E b values are lower than in previous literature reports and lower than expected from standard theory that assumes excitons are screened by optical-frequency dielectric constants. These low E b values are shown to be a consequence of unique screening effects, such as superlattice screening and phonon screening. Here, we find a strikingly strong correlation between E b and E g and provide design principles to a priori tune E g and E b to their optimal values. As such, this work offers a blueprint for E g -E b engineering of low-dimensional semiconductors as an even more useful replacement for simply band-gap engineering.

14 SOLAR ENERGY↗

Nitrogen–doped graphitized carbon shell encapsulated NiFe nanoparticles: A highly durable oxygen evolution catalyst

Oxygen evolution reaction (OER) plays a crucial role in various energy conversion devices such as water electrolyzers and metal–air batteries. Precious metal catalysts such as Ir, Ru and their oxides are usually used for enhancing reaction kinetics but are limited by their scarce resource. The challenges associated with alternative non–precious metal catalysts such as transition metal oxides and (oxy)hydroxides etc. are their low electronic conductivity and durability. Herein, we report a highly active (360 mV overpotential at 10 mA cm–2GEO) and durable (no degradation after 20000 cycles) OER catalyst derived from bimetallic metal–organic frameworks (MOFs) precursors. This catalyst consists of NiFe nanoparticles encapsulated by nitrogen–doped graphitized carbon shells. The electron-donation/deviation from Fe and tuned electronic structure of metal cores by Ni are revealed to be primary contributors to the enhanced OER activity, whereas N concentration contributes negligibly. We further demonstrated that the structure and morphology of encapsulating carbon shells, which are the key factors influencing the durability, are facilely controlled by the chemical state of precursors.

Environmental Molecular Sciences Laboratory↗

The influence of interfaces on properties of thin-film inorganic structural isomers containing SnSe—NbSe₂ Subunits

Inorganic isomers ([SnSe] 1+δ ) m (NbSe₂) n ([SnSe] 1+δ ) p (NbSe₂) q ([SnSe] 1+δ ) r (NbSe₂) s where m , n , p , q , r , and s are integers and m + p + r = n + q + s = 4 were prepared using the modulated elemental reactant technique. This series of all six possible isomers provides an opportunity to study the influence of interface density on properties while maintaining the same unit cell size and composition. As expected, all six compounds were observed to have the same atomic compositions and an almost c-axis lattice parameter of ≈4.90 (5) nm, with a slight trend in the c-axis lattice parameter correlated with the different number of interfaces in the isomers: two, four and six. The structures of the constituents in the ab-plane were independent of one another, confirming the nonepitaxial relationship between them. The temperature dependent electrical resistivities revealed metallic behavior for all the six compounds. Surprisingly, the electrical resistivity at room temperature decreases with increasing number of interfaces. Hall measurements suggest this results from changes in carrier concentration, which increases with increasing thickness of the thickest SnSe block in the isomer. Carrier mobility scales with the thickness of the thickest NbSe₂ block due to increased interfacial scattering as the NbSe₂ blocks become thinner. The observed behavior suggests that the two constituents serve different purposes with respect to electrical transport. SnSe acts as a charge donor and NbSe₂ acts as the charge transport layer. This separation of function suggests that such heterostructures can be designed to optimize performance through choice of constituent, layer thickness, and layer sequence. A simplistic model, which predicts the properties of the complex isomers from a weighted sum of the properties of building blocks, was developed. A theoretical model is needed to predict the optimal compound for specific properties among the many potential compounds that can be prepared.

Alemayehu, Matti B.↗

An ℓ 0 ℓ 2 -norm regularized regression model for construction of robust cluster expansions in multicomponent systems

In this work we introduce ℓ 0 ℓ 2 -norm regularization and hierarchy constraints into linear regression for the construction of cluster expansions to describe configurational disorder in materials. The approach is implemented through mixed integer quadratic programming (MIQP). The ℓ 2 -norm regularization is used to suppress intrinsic data noise, while the ℓ 0 -norm is used to penalize the number of nonzero elements in the solution. The hierarchy relation between clusters imposes relevant physics and is naturally included by the MIQP paradigm. As such, sparseness and cluster hierarchy can be well optimized to obtain a robust, converged set of effective cluster interactions with improved physical meaning. We demonstrate the effectiveness of ℓ 0 ℓ 2 -norm regularization in two high-component disordered rocksalt cathode material systems, where we compare the cross-validation, convergence speed, and the reproduction of phase diagrams, voltage profiles, and Li-occupancy energies with those of the conventional ℓ 1 -norm regularized cluster expansion models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio study of mechanical and thermal properties of GeTe-based and PbSe-based high-entropy chalcogenides

GeTe-based and PbSe-based high-entropy compounds have outstanding thermoelectric (TE) performance and crucial applications in mid and high temperatures. Recently, the optimization of TE performance of high-entropy compounds has been focused on reducing thermal conductivity by strengthening the phonon scattering process to improve TE performance. We report a first-principles investigation on nine GeTe-based high-entropy chalcogenide solid solutions constituted of eight metallic elements (Ag, Pb, Sb, Bi, Cu, Cd, Mn, and Sn) and 13 PbSe-based high-entropy chalcogenide solid solutions: Pb 0.99-y Sb 0.012 Sn y Se 1-2x Te x S x (x = 0.1, 0.2, 0.25, 0.3, 0.35, 0.4, 0.45, and y = 0) and Pb 0.99-y Sb 0.012 Sn y Se 1-2x Te x S x (y = 0.05, 0.1, 0.15, 0.2, 0.25 and x = 0.25). We have investigated the mechanical properties focusing on Debye temperature (Θ D ), thermal conductivity (κ), Grüneisen parameter (γ α ), dominant phonon wavelength (λ dom ), and melting temperature (T m ). We find that the lattice thermal conductivity is significantly reduced when GeTe is alloyed into the following compositions: Ge 0.75 Sb 0.13 Pb 0.12 Te, Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te, and Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Mn 0.05 Bi 0.01 Te. This reduction is due to the mass increase and strain fluctuations. The results also show that Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te solid solution has the lowest Young’s modulus (30.362 GPa), bulk and shear moduli (18.626 and 12.359 GPa), average sound velocity (1653.128 m/sec), Debye temperature (151.689 K), lattice thermal conductivity (0.574 W.m –1 .K –1 ), dominant phonon wavelength (0.692 Å), and melting temperature (535.91 K). Moreover, Ge 0.61 Ag 0.11 Sb 0.13 Pb 0.12 Bi 0.01 Te has the highest Grüneisen parameter with a reduced and temperature-independent lattice thermal conductivity. The positive correlation between Θ D and κ is revealed. Alloying of PbSe-based high-entropy by Sb, Sn, Te, and S atoms at the Se and Pb sites resulted in much higher shear strains resulted in the reduction of phonon velocity, a reduced Θ D , and a lower lattice thermal conductivity.

74 ATOMIC AND MOLECULAR PHYSICS↗

Modular Adaptive Packing for Integrally Cooled Absorbers

Process intensification is one cornerstone in ION Clean Energy’s (ION) efforts to lowering CO2 capture cost. ION has modeled, designed, and fabricated an innovative gas-liquid contactor known as Modular Adaptive Packing (MAP). During two successful SBIR Phase I and II projects entitled: “Rapid Design and Testing of Novel Gas-Liquid Contacting Devices for Post-Combustion CO2 Capture via 3D-printing”, ION developed and proved this new technology at bench scale. MAP, a 3D-printed lattice-structured packing, combines the absorber gas/liquid contactor with an innovative in-situ heat-exchanger. Thanks to the capabilities of 3D-printing, the lattice structure of MAP contains hollow channels through which coolant water can be pumped to remove the heat of reaction from CO2 absorption. ION refers to this novel method of heat exchange as intracooling. After 25.4 cm (10 in) diameter MAP modules were fabricated, ION built and tested a packing characterization rig at its pilot facility in Boulder, Colorado, U.S.A. To provide baseline results for the characterization rig, ION tested Sulzer’s Mellapak™ 250Y (MP250Y) as a standard structured packing. ION’s MAP was then compared directly to the baseline MP250Y packing to evaluate key indicators including pressure drop, liquid hold-up, and effective area. MAP has a higher pressure drop than MP250Y at the same gas velocities in addition to greater liquid holdup. However, ION found that MAP displays a higher wetting coverage of 93% compared to 65% for MP250Y and reduces shearing forces that result in undesirable droplet formation. Using Optimized Gas Treating’s (OGT) rate-based simulation software ProTreat®, a conceptual evaluation of MAP was modeled for a CO2 absorber using 30 wt% MEA solvent over a range of lean loadings at 90% CO2 capture from a coal-fired power plant. ION modeled a 25-meter column absorber for both the standard MP250Y packing and a hybrid column. The hybrid absorber contained 10 m of MP250Y packing at the top and bottom with the middle 5 meters comprised of MAP. Compared to a traditional intercooled absorber, MAP can remove 22% more heat and increase overall MEA carrying capacity by 4% without increasing overall pressure drop.

20 FOSSIL-FUELED POWER PLANTS↗

Production of LEU fully ceramic microencapsulated fuel for irradiation testing

The Advanced Fuels Campaign of the US DOE Fuel Cycle Research/Development program is currently engaged in production of FCM fuel for irradiation testing in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). FCM fuel production is a serial process with 3 major steps namely kernel, TRISO, and compact production. The first step in the kernel process is production of air-dried UO{sub 3} gel spheres with suspended carbon particles. These spheres, roughly 2 mm in size, are then calcined to produce a mixture of UO{sub 2} and carbon. This calcination step may be performed in either argon, hydrogen, or mixtures of these gases. Once the calcination step is complete, temperature is increased (>1400 Celsius degrees) to convert this mixture to UO{sub 2} + UC{sub x}. Once dense oxide-carbide kernels are available, the inert environment is switched to a nitrogen containing one to facilitate carbothermic reduction of kernels and production of UN. Essentially, the oxygen and carbon in the oxide-carbide kernels react with one another to produce CO and are replaced with nitrogen inside the lattice. The TRISO step in fuel production is incorporation of a porous carbon buffer layer, a dense inner pyrolytic carbon layer (IPyC), a SiC layer, and finally and outer pyrolytic carbon layer (OPyC) onto the UN kernels. The coating layer deposition step is carried out inside a graphite furnace using a fluidized bed chemical vapor deposition (CVD) process. In essence, a mixture of reactant and inert gasses flow from the bottom through a bed of particles that are in turn fluidized by the gas stream. The particles undergo CVD and once a different coating layer is to be incorporated, the furnace temperature is adjusted and the reactant gases are changed. The final step in the series of fuel production activities is the consolidation of UN TRISO particles inside the SiC matrix to produce cylindrical pellets. It entails 3 critical areas: SiC powder mixing, over-coating of particles, and high-temperature densification. Optimal execution of the powder mixing step is vital to achieve a fully dense SiC matrix at the end of the process. The SiC matrix is consolidated using a special form of liquid phase sintering (LPS) involving nano-powder feedstock that is designated as the NITE process. The SiC nano-powder slurry is sprayed directly onto the particle surface using a piezoelectric nozzle. Once the over-coated particles are available, final consolidation step at high temperatures (1875 Celsius degrees) is carried out.

36 MATERIALS SCIENCE↗

Thermodynamics and magnetism in the two-dimensional to three-dimensional crossover of the Hubbard model

The realization of antiferromagnetic (AF) correlations in ultracold fermionic atoms on an optical lattice is a significant achievement. Experiments have been carried out in one, two, and three dimensions, and have also studied anisotropic configurations with stronger tunneling in some lattice directions. Such anisotropy is relevant to the physics of cuprate superconductors and other strongly correlated materials. Moreover, this anisotropy might be harnessed to enhance AF order. Here we numerically investigate, using the determinant quantum Monte Carlo method, a simple realization of anisotropy in the three-dimensional (3D) Hubbard model in which the tunneling between planes, $t_⊥$, is unequal to the intraplane tunneling $\textit{t}$. This model interpolates between the three-dimensional isotropic ($t_⊥ = t$) and two-dimensional (2D;$t_⊥$ = 0) systems. In this work, we show that at fixed interaction strength to tunneling ratio ($\textit{U/t}$), anisotropy can enhance the magnetic structure factor relative to both 2D and 3D results. However, this enhancement occurs at interaction strengths below those for which the Néel temperature $T_{\text{Néel}}$ is largest, in such a way that the structure factor cannot be made to exceed its value in isotropic 3D systems at the optimal $\textit{U/t}$. We characterize the 2D-3D crossover in terms of the magnetic structure factor, real space spin correlations, number of doubly occupied sites, and thermodynamic observables. An interesting implication of our results stems from the entropy's dependence on anisotropy. As the system evolves from 3D to 2D, the entropy at a fixed temperature increases. Correspondingly, at fixed entropy, the temperature will decrease going from 3D to 2D. This suggests a cooling protocol in which the dimensionality is adiabatically changed from 3D to 2D.

74 ATOMIC AND MOLECULAR PHYSICS↗

Prediction of forces and moments for flight vehicle control effectors: Workplan

Two research activities directed at hypersonic vehicle configurations are currently underway. The first involves the validation of a number of classical local surface inclination methods commonly employed in preliminary design studies of hypersonic flight vehicles. Unlike studies aimed at validating such methods for predicting overall vehicle aerodynamics, this effort emphasizes validating the prediction of forces and moments for flight control studies. Specifically, several vehicle configurations for which experimental or flight-test data are available are being examined. By comparing the theoretical predictions with these data, the strengths and weaknesses of the local surface inclination methods can be ascertained and possible improvements suggested. The second research effort, of significance to control during take-off and landing of most proposed hypersonic vehicle configurations, is aimed at determining the change due to ground effect in control effectiveness of highly swept delta planforms. Central to this research is the development of a vortex-lattice computer program which incorporates an unforced trailing vortex sheet and an image ground plane. With this program, the change in pitching moment of the basic vehicle due to ground proximity, and whether or not there is sufficient control power available to trim, can be determined. In addition to the current work, two different research directions are suggested for future study. The first is aimed at developing an interactive computer program to assist the flight controls engineer in determining the forces and moments generated by different types of control effectors that might be used on hypersonic vehicles. The first phase of this work would deal in the subsonic portion of the flight envelope, while later efforts would explore the supersonic/hypersonic flight regimes. The second proposed research direction would explore methods for determining the aerodynamic trim drag of a generic hypersonic flight vehicle and ways in which it can be minimized through vehicle design and trajectory optimization.

Maughmer, Mark D.↗

Blue photons excited highly chromatic red light emitting K3La(PO4)2:Pr3+ phosphors for white light emitting diodes

Highlights: • K{sub 3}La(PO{sub 4}){sub 2}:Pr{sup 3+} phosphors were investigated as an alternative for red light. • Highly chromatic red emission was realized upon blue excitation. • The phosphor has high color purity ∼ 97.8% and yield ∼27%. - Abstract: Highly chromatic blue photons excited red emitting K{sub 3}La(PO{sub 4}){sub 2}:Pr{sup 3+} (0–1.8 mol%) phosphors were synthesized by solution combustion method. The resulted phosphors showed peanut like morphology and had a monoclinic phase with space group P2{sub 1}/m. The photoluminescence studies disclosed that the phosphor emits red light due to the {sup 1}D{sub 2} → {sup 3}H{sub 4} and {sup 1}D{sub 2} → {sup 3}H{sub 5} transition of the Pr{sup 3+} ions under blue photons excitation. The optimal concentration for the Pr{sup 3+} ions were optimized to be 1.2 mol% after which concentration quenching occurred. Dipole-dipole interaction among the dopant ions was found to be responsible for the concentration quenching. X-ray photoelectron spectroscopy results depicted that Pr was present in the (+3) valance state in the phosphor. The photometric results suggest that the phosphor with a high color purity ∼ 97.8% and enough quantum yield ∼27% could be an eventual choice as the red component for white light emitting diodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic structure and thermoelectric properties of pnictogen-substituted ASn{sub 1.5}Te{sub 1.5} (A = Co, Rh, Ir) skutterudites

Substituting group 14 and 16 elements on the pnictogen site in the skutterudite structure yields a class of valence-precise ternary AX{sub 1.5}Y{sub 1.5} compounds (A = Co, Rh, Ir, X = Sn, Ge, and Y = S, Se, Te), in which X and Y form an ordered sub-structure. Compared with unfilled binary skutterudites, pnictogen-substituted phases exhibit extremely low lattice thermal conductivity due to increased structural complexity. Here, we investigate the role of the transition metal species in determining the electronic structure and transport properties of ASn{sub 1.5}Te{sub 1.5} compounds with A = Co, Rh, Ir. Density functional calculations using fully ordered structures reveal semiconducting behavior in all three compounds, with the band gap varying from 0.2 to 0.45 eV. In CoSn{sub 1.5}Te{sub 1.5}, the electronic density of states near the gap is significantly higher than for A = Ir or Rh, leading to higher effective masses and higher Seebeck coefficients. Experimentally, Ir and Rh samples exhibit relatively large p-type carrier concentrations and degenerate semiconducting behavior. In contrast, CoSn{sub 1.5}Te{sub 1.5} shows mixed conduction, with n-type carriers dominating the Seebeck coefficient and light, high mobility holes dominating the Hall coefficient. zT values of up to 0.35 were obtained, and further improvement is expected upon optimization of the carrier concentration or with n-type doping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Precisely computing phonons via irreducible derivatives

Computing phonons from first principles is typically considered a solved problem, yet inadequacies in existing techniques continue to yield deficient results in systems with sensitive phonons. Here, in this study, we circumvent this issue using the lone irreducible derivative (LID) and bundled irreducible derivative (BID) approaches to computing phonons via finite displacements, where the former optimizes precision via energy derivatives and the latter provides the most efficient algorithm using force derivatives. A condition number optimized basis for BID is derived which guarantees the minimum amplification of error. Additionally, a hybrid LID-BID approach is formulated, in which select irreducible derivatives computed using LID replace BID results. We illustrate our approach on two prototypical systems with sensitive phonons: the shape memory alloy AuZn and metallic lithium. Comparing our resulting phonons in the aforementioned crystals to calculations in the literature reveals nontrivial inaccuracies. Our approaches can be fully automated, making them well suited for both niche systems of interest and high-throughput approaches.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal decomposition of t-butylamine borane studied by in situ solid state NMR

Development of suitable materials to store hydrogen for automotive use has received pointed attention over the past decade. Significant progress has been made with the discovery of novel chemical hydrides, complex metal hydrides, and adsorption substrates which continue to optimize both thermodynamics and kinetics of hydrogen sorption. Chemical hydrides typically offer the largest theoretical gravimetric capacities. Autrey et al. have recently shown that mechanical milling of alkali metal hydrides with ammonia borane can further lower the decomposition temperature. In all cases, however, many challenges remain in order to meet the current US DOE performance targets. Amine boranes are being considered for hydrogen storage materials since they contain significant quantities of hydrogen which potentially can be released at low temperatures (80-150 C) via chemical reactions. Ammonia borane, NH{sub 3}BH{sub 3}, is one of the most promising in this class as it decomposes to release greater than two moles of pure hydrogen gas (14 wt%) below 160 C. Although isoelectronic to ethane, NH{sub 3}BH{sub 3} is a solid at room temperature due to the di-hydrogen bonding network formed between the amine protons and boron hydrides in the solid state lattice. Further, it has been shown that the hydrogen release mechanism involves transformation and isomerization to an ionic dimer where a hydride migrates from one boron to the adjacent boron in the dimer. The greatest challenge to the use of ammonia borane as a hydrogen fuel is the regeneration path from spent fuel to ammonia borane again. The proposed chemical synthesis involves complicated organometallic reactions to form boron hydrogen bonds from the thermodynamically stable polyimidoborane products (BNH){sub n}. Recent theoretical calculations suggested that incorporation of carbon atoms into the (BNH)n product would be less thermodynamically stable. These (CBNH)n compounds are potentially less energy intensive making regeneration of the amine borane fuel more feasible [22]. In the present study, tert-butylamine borane is investigated by heteronuclear in situ solid state NMR to understand hydrogen release from a hydrocarbon containing amine borane. tbutylamine borane has similar physical properties to amine borane with a melting point of 96 C. A single proton has been replaced with a t-butylamine group resulting in a weakening of the dihydrogen bonding framework. t-butylamine borane has a theoretical gravimetric hydrogen density of 15.1%; however, isobutane can also be evolved rather than hydrogen. If decomposition yields one mole isobutane and two moles hydrogen, 4.5 wt% H2 gas will be evolved. More importantly for the present work, the resulting spent fuel should be comprised of both (BNH)n and (CBNH)n polyimidoboranes.

08 HYDROGEN↗

Additive‐Free, Low‐Temperature Crystallization of Stable α‐FAPbI 3 Perovskite

Abstract Formamidinium lead triiodide (FAPbI 3 ) is attractive for photovoltaic devices due to its optimal bandgap at around 1.45 eV and improved thermal stability compared with methylammonium‐based perovskites. Crystallization of phase‐pure α‐FAPbI 3 conventionally requires high‐temperature thermal annealing at 150 °C whilst the obtained α‐FAPbI 3 is metastable at room temperature. Here, aerosol‐assisted crystallization (AAC) is reported, which converts yellow δ‐FAPbI 3 into black α‐FAPbI 3 at only 100 °C using precursor solutions containing only lead iodide and formamidinium iodide with no chemical additives. The obtained α‐FAPbI 3 exhibits remarkably enhanced stability compared to the 150 °C annealed counterparts, in combination with improvements in film crystallinity and photoluminescence yield. Using X‐ray diffraction, X‐ray scattering, and density functional theory simulation, it is identified that relaxation of residual tensile strains, achieved through the lower annealing temperature and post‐crystallization crystal growth during AAC, is the key factor that facilitates the formation of phase‐stable α‐FAPbI 3 . This overcomes the strain‐induced lattice expansion that is known to cause the metastability of α‐FAPbI 3 . Accordingly, pure FAPbI 3 p–i–n solar cells are reported, facilitated by the low‐temperature (≤100 °C) AAC processing, which demonstrates increases of both power conversion efficiency and operational stability compared to devices fabricated using 150 °C annealed films.

36 MATERIALS SCIENCE↗

Reaction Mechanism of Electrodeposited ε-MnO 2 : A Proton-Centered Pathway in Aqueous Zn-Ion Systems

Aqueous Zn/MnO 2 batteries have garnered significant interests owing to their abundance, high theoretical specific capacity, safety, and low cost. However, large-scale application of these systems is limited by the incomplete understanding of the MnO 2 reaction chemistry. The different crystal lattice structures among MnO 2 polymorphs contribute to the variations in reported reaction mechanisms. Among them, ε-MnO 2 polymorph, the dominant phase in electrolytic manganese dioxide (EMD), is notably observed during the charge cycles of aqueous Zn/MnO 2 batteries. Here, in this work, we investigate the electrochemical behavior of an ε-MnO 2 cathode synthesized via electrodeposition from a ZnSO 4 and MnSO 4 electrolyte, onto a 3-dimensional carbon cloth substrate. Proton intercalation emerges as the dominant charge storage mechanism, critically enabling the reversibility of ε-MnO 2 during cycling, as revealed by operando synchrotron X-ray diffraction and X-ray absorption spectroscopy. Additionally, a proton-coupled dissolution/redeposition pathway operates alongside minor Zn 2+ intercalation, as quantified by Rietveld refinement. Morphological and chemical heterogeneities are studied by transmission X-ray microscopy further validates this reaction mechanism. These mechanistic insights provide the foundation for rationally designing Zn/MnO 2 batteries with optimized proton dynamics and charge transfer, advancing these systems as a viable solution for safe, cost-effective grid-scale energy storage.

36 MATERIALS SCIENCE↗