Search NASA⌕ Search

SEARCH · Search NASA

Results for “THERMAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

In situ observation of the deformation and fracture of an alumina-alumina ceramic-matrix composite at elevated temperature using x-ray computed tomography

The deformation and fracture of a 0/90° Nextel 720 mullite fibre / alumina matrix ceramic-matrix composite material has been observed by in situ synchrotron x-ray computed micro-tomography at ambient temperature and at 1100 °C. A three-point loading configuration was used and samples were loaded monotonically until final fracture. Here, the flexural strength was found to be unaffected by temperature. 3D visualisation of the microstructure showed fracture occurred by propagation of internal cracks at stresses close to the flexural strength. Shear fractures propagated across fibre bundles that were oriented perpendicular to the flexural stress at both room temperature and 1100 °C. At the higher temperature, an additional failure mode of delamination was observed, that may arise from relaxation of thermal residual stresses and creep.

36 MATERIALS SCIENCE↗

Thermally induced PtOx interfacial layer enhances stability of Pt/β-Ga2O3 vertical Schottky diodes

This study investigates the long-term stability of Pt/β-Ga2O3 field-plated Schottky barrier diodes at high temperatures, with extended thermal cycling and soaking stress. The device characteristics reveal a strong dependence on operating temperature, leading to an ON/OFF current ratio of ∼10× at ±3 V and 600 °C. Extensive thermal cycling (25 cycles over 100 h) between room temperature and 350 °C shows that leakage currents stabilize after the initial ten cycles. This stabilization is likely due to the formation of a thin PtOx layer at the Pt/β-Ga2O3 interface, as confirmed by high-resolution scanning transmission electron microscopy. Further exposure to a constant 350 °C environment for 10 h reveals a slight increase in the leakage current from 10−7 to 10−6 A at −5 V and degradation of the forward current, due to potential thermodynamic instability of the Ohmic contacts. This study provides insights into the changes in the Pt/β-Ga2O3 diode performance with thermal stress, offering a basis for predicting the device’s operational reliability at high temperatures for sensing and power applications.

08 HYDROGEN↗

FWP FEAA149: “Next Generation Environmental Barrier Coatings”

Environmental barrier coatings (EBCs) are required coatings for utilization of SiC/SiC ceramic matrix composite (CMC) components in gas turbines, where the EBC represents the life-limiting factor for such components. EBC/CMC systems have shown success in aero-engine applications with increased turbine inlet temperatures and improved efficiencies, which are achieved through higher temperature stability, lower density, and decreased reliance on cooling air compared to traditional superalloys. While industrial gas turbines (IGTs) do not currently utilize SiC/SiC CMCs, the current shift towards low-carbon or carbon-free fuel sources for power generation could result in a need for EBC/CMC components with higher temperature capabilities. In this work, three tasks were outlined to improve understanding of EBC lifetimes to encourage use in IGTs with carbon-free fuel such as hydrogen: 1. Define the bond coating oxidation kinetics and EBC failure criteria, 2. Measure thermal expansion coefficients of each layered material, and 3. Perform advanced characterization and modeling to assess EBC lifetimes. Cyclic steam oxidation tests were conducted on various EBC/Si/SiC chemistries and EBC/SiC architectures to define substrate oxidation kinetics and EBC failure modes. An open-source code was developed to quantify the undulating thermally grown oxide thickness with thousands of measurements from specimen cross-section images. Bond coating oxidation kinetics were determined and used to develop a kinetic and thermodynamic model for predicting EBC lifetimes. High-temperature Raman spectroscopy was utilized for determining the SiO 2 thermally grown oxide phase transformation as the life-limiting feature for EBCs. Model efforts supported the claim that the SiO 2 phase transformation causes elevated stress during thermal cycling with associated cracking that decreases the adhesion strength of the EBC, eventually resulting in coating spallation. The finite element model subroutine will be made publicly available upon internal review. Further development of an EBC lifetime model for IGTs involves definition of a critical SiO 2 thickness for EBC spallation and must also consider both environmental (gas velocity, pressure, etc.) and specimen (EBC dopants, layer architectures, etc.) effects into predicted bond coating oxidation kinetics for long-lifetime components.

36 MATERIALS SCIENCE↗

The relationship between reliability and bonding techniques in hybrid microcircuits

Differential thermal expansion was shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. It is shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis was conducted of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses. It was experimentally observed that the stresses in more compliant bonding systems such as soft lead tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate was proven to be a determining factor in the prediction of failure solder systems. It was found that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Strain gage techniques were used to determine thermally induced expansion stresses of the capacitors and the alumina substrates. The compliance of the different bonding mediums was determined. From the data obtained, several recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.

Caruso, S. V.↗

Development of a prototype automated on-orbit contact heat exchanger

An automated contact heat exchanger is being developed for use aboard the manned Space Station, serving as an interface heat exchanger between the pressurized module internal thermal buses and the central external thermal bus. The concept makes use of an array of flattened, thin-walled, flexible tubes that expand or contract to make or break the thermal connection as the internal pressure changes. Because of its simplicity, it permits on-orbit assembly by the remote manipulator system, thus eliminating the need for expensive EVA to make connections. A design methodology based on stress and thermal analyses has been developed and used to perform trade-offs between performance and cost, and to optimize design parameters. Simple verification tests have been performed to confirm the stress analysis model. Two conceptual variants of the contact heat exchanger are described, each designed for a 25 kW total heat load and a minimum uniform heat flux of 2.15 W/sq cm.

Lee, C. Y.↗

Observed changes in a-Si:H cell characteristics due to long term temperature stress

Determination of thermally induced degradation mechanisms affecting thin film amorphous silicon solar cells through the use of laboratory accelerated stress testing requires acquisition of specially constructed, individually addressable test cells and the development of highly repeatable instrumentation which is not influenced by short-term reversible optical effects. This paper illustrates these considerations by describing accelerated temperature stress procedures and test results for one type of a-Si:H cell. Observed electrical characteristic changes indicate that two types of stress induced mechanisms are operating - one of which is self limiting and can be observed at lower temperatures and one which continues to complete degradation. The self limiting mechanism can result in a dramatic improvement to cells having initially low Voc values.

Lathrop, Jay W.↗

Molecular models for creep in oriented polyethylene fibers

Highly oriented and crystalline polyetheylene (PE) fibers have a large failure stress under rapid tensile loading but exhibit significant creep at much smaller stresses that limits applications. A possible mechanism is slip of chains due to stress-enhanced, thermally activated nucleation of dislocations at chain ends in crystalline regions. Molecular dynamics simulations are used to parameterize a Frenkel–Kontorova model that provides analytic expressions for the limiting stress and activation energy for dislocation nucleation as a function of stress. Results from four commonly used hydrocarbon potentials are compared to show that the qualitative behavior is robust and estimate quantitative uncertainties. In all cases, the results can be described by an Eyring model with values of the zero-stress activation energy Ea0≈1.5 eV and activation volume V* ≈ 45 Å3 that are consistent with the experimental results for increasingly crystalline materials. The limiting yield stress is ∼8 GPa. These results suggest that activated dislocation nucleation at chain ends is an important mechanism for creep in highly oriented PE fibers.

O’Connor, Thomas C. (ORCID:0000000293930295)↗

TOUGH-RFPA: Coupled thermal-hydraulic-mechanical Rock Failure Process Analysis with application to deep geothermal wells

This paper presents a coupled thermal-hydraulic-mechanical (THM) model for simulating failure processes in geological media. The coupling between stress/strain and heat transfer describing how thermal expansion affects stress is based on the theory of thermo-elasticity. Additionally, the coupling between stress/strain and fluid flow describing how pore-pressure affects stress is governed by Biot's consolidation theory. Stress/strain-dependent porosity/permeability/capillary-pressure defines the influence of stress on fluid flow and thermal fields. The THM model is implemented in the solver module that links the multiphase, multicomponent fluid flow simulator TOUGH2 with the geomechanical simulator RFPA (Rock Failure Process Analysis), which is based on the concept that heterogeneity leads to non-linearity and progressive failure behavior. Capability of TOUGH-RFPA simulator was verified by two benchmark problems related to hydraulic-mechanical and thermal-mechanical response in a hollow cylinder. Then the applicability of TOUGH-RFPA was demonstrated for modeling cooling-induced damage around a very deep geothermal well with mesoscopic heterogeneous properties, which showed complex damage evolution and fracturing during well cooling and fluid pressurization.

42 ENGINEERING↗

An Evaluation of the Use of X-ray Residual Stress Determination as a Means of Characterizing Oxidation Damage of Nickel-Based, Cr2O3-Forming Superalloys Subjected to Various Oxidizing Condition

The use of X-ray residual stress determination as a technique for evaluating the damage incurred by nickel-based, Cr2O3-forming superalloy materials under various service conditions (isothermal heating, thermal cycling, applied stress, stressed and cycled) was investigated. Large and small compressive residual stresses were observed for the oxides and the near surface substrates, respectively. It was expected that the applied stresses and thermal cycling would cause an enhanced degree of oxidation damage that would translate into appreciable differences in residual stress values. Differences in the magnitude of residual stress values were not appreciable condition-to-condition, however. An increase in the severity of the oxidizing conditions in the form of longer oxidation times, higher oxidizing temperatures, and a much greater frequency of thermal cycling is suggested for future studies.

36 MATERIALS SCIENCE↗

Combined Stress Testing of Perovskite Solar Cells for Stable Operation in Space

Perovskite solar cells (PSCs) could provide new low-cost opportunities for powering spacecraft. Here we are designing a PSC resilient to lunar surface conditions, focusing on contact/barrier layers combinations that maximize stability. Thermal vacuum stress shows cells with gold back-contacts and SiOx protection retain >90% of initial efficiency and indium tin oxide (ITO)-contacted cells retain ~100% of initial efficiency after five months of stress. SiO x mitigates mechanical aspects of contact stress, retaining 99% of initial efficiency, whereas cells with silicone/cover glass decreased 27%. We further exposed cells to combined illumination, 75 °C heat, and 10 -6 Torr vacuum for 24 h and found that ITO-contacted cells outperformed Au-contacted cells.

14 SOLAR ENERGY↗

A geometrically nonlinear analysis of interlaminar stresses in unsymmetrically laminated plates subjected to uniform thermal loading

An analytical study of interlaminar stresses in unsymmetrically laminated plates is presented. The study examines the linear elastic, large deflection response of square laminated composite plates subjected to uniform thermal loading. Both cross-ply and angle-ply, symmetric and unsymmetric, laminates are examined to evaluate the effects of mismatch between adjacent layers in elastic constants and coefficients of thermal expansion. A geometrically nonlinear kinematic description is used to predict the large out-of-plane (transverse) deflections. The nonlinear, three-dimensional boundary value problems are formulated from elasticity theory and approximate solutions are determined using the finite element method. A global/local analysis procedure is used to obtain improved free edge stress predictions. For the laminates and loading conditions considered, the results indicate that the out-of-plane deflections of the unsymmetric laminates reduce interlaminar shear stresses. These deflections also reduce interlaminar normal stresses in some laminates and increase these stresses for others. The results indicate that as the out-of-plane deflections become large, the differences in interlaminar stress predictions between linear and nonlinear theory can become quite large.

Norwood, D. S.↗

Effect of microstructure on the coupled electromagnetic-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates to infrared laser radiation

The coupled electromagnetic (EM)-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates under laser irradiation and high strain rate loads has been investigated for various aggregate sizes and binder volume fractions. The cyclotrimethylenetrinitramine (RDX) crystals are modeled with a dislocation density-based crystalline plasticity formulation and the estane binder is modeled with finite viscoelasticity through a nonlinear finite element approach that couples EM wave propagation with laser heat absorption, thermal conduction, and inelastic deformation. Material property and local behavior mismatch at the crystal-binder interfaces resulted in geometric scattering of the EM wave, electric field and laser heating localization, high stress gradients, dislocation density, and crystalline shear slip accumulation. Viscous sliding in the binder was another energy dissipation mechanism that reduced stresses in aggregates with thicker binder ligaments and larger binder volume fractions. This investigation indicates the complex interactions between EM waves and mechanical behavior, for accurate predictions of laser irradiation of heterogeneous materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Trajectory Optimization of Electric Aircraft Subject to Subsystem Thermal Constraints

Electric aircraft pose a unique design challenge in that they lack a simple way to reject waste heat from the power train. While conventional aircraft reject most of their excess heat in the exhaust stream, for electric aircraft this is not an option. To examine the implications of this challenge on electric aircraft design and performance, we developed a model of the electric subsystems for the NASA X-57 electric testbed aircraft. We then coupled this model with a model of simple 2D aircraft dynamics and used a Legendre-Gauss-Lobatto collocation optimal control approach to find optimal trajectories for the aircraft with and without thermal constraints. The results show that the X-57 heat rejection systems are well designed for maximum-range and maximum-efficiency flight, without the need to deviate from an optimal trajectory. Stressing the thermal constraints by reducing the cooling capacity or requiring faster flight has a minimal impact on performance, as the trajectory optimization technique is able to find flight paths which honor the thermal constraints with relatively minor deviations from the nominal optimal trajectory.

electric propulsion↗

Magnetically induced cylindrical stress waves in a thermoelastic conductor

The problem of stress wave generation in a linear thermoelastic solid by a pulsed magnetic field is investigated both analytically and experimentally for a cylindrically symmetric conducting solid. A dynamic response analysis is developed to correlate magnetic, thermal, and stress fields in the solid with the time history of the electric current. In the experiment, a transient magnetic field was applied normal to a large conducting plate with a circular hole. Initially the field was confined to the interior of the circular hole. The field was generated by discharging a large capacitor bank through a solenoidal coil. The plane-stress cylindrical stress waves are 1-D in nature. The relative effects of the magnetic body force and thermoelastic stresses, both generated by the electromagnetic field, are assessed.

Chian, C. T.↗

Vertical movement in mare basins - Relation to mare emplacement, basin tectonics, and lunar thermal history

A hypothesis is developed that the spatial and temporal distributions of linear rilles and mare ridges in the mare regions of the moon are the products of two superposed stress systems: a local stress due to lithospheric loading by basalt fill in the mare basin, and a global thermal stress due to the thermal history of the lunar interior. Quantitative models for stress in the Serenitatis basin area, including the global thermal stress associated with lunar thermal history, are presented and used to account for the spatial distribution, the orientations, and the formation times of rilles and ridges in that region. The models provide a simple explanation for the localization of the most recent eruption sites of mare basalt magmas to mare basin edges.

Solomon, S. C.↗

Frequency-resolved Raman for transient thermal probing and thermal diffusivity measurement

Steady state Raman has been widely used for temperature probing and thermal conductivity/conductance measurement in combination with temperature coefficient calibration. In this work, a new transient Raman thermal probing technique: frequency-resolved Raman (FR-Raman) is developed for probing the transient thermal response of materials and measuring their thermal diffusivity. The FR-Raman uses an amplitude modulated square-wave laser for simultaneous material heating and Raman excitation. The evolution profile of Raman properties: intensity, Raman wavenumber, and emission, against frequency are measured experimentally and reconstructed theoretically. They are used for fitting to determine the thermal diffusivity of the material under test. A Si cantilever is used to investigate the capacity of this new technique. The cantilever’s thermal diffusivity is determined as 9.57 × 10 -5 m 2 /s, 11.00 × 10 -5 m 2 /s and 9.02 × 10 -5 m 2 /s by fitting the Raman intensity, wavenumber and emission. The deviation from the reference value is largely attributed to thermal stress-induced material deflection and Raman drift, which could be significantly suppressed by using a higher sensitivity Raman spectrometer with lower laser energy. As a result, the FR-Raman provides a novel way for transient thermal characterization of materials with a ?m spatial resolution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modifications of a Composite-Material Combustion Chamber

Two short reports discuss modifications of a small, lightweight combustion chamber that comprises a carbon/carbon composite outer shell and an iridium/ rhenium inner liner. The first report discusses chamber design modifications made as results of hot-fire tests and post-test characterization. The Books & Reports 32 NASA Tech Briefs, June 2005 modifications were intended to serve a variety of purposes, including improving fabrication, reducing thermal-expansion mismatch stresses, increasing strength-to-weight ratios of some components, and improving cooling of some components. The second report discusses (1) the origin of stress in the mismatch between the thermal expansions of the Ir/Re liner and a niobium sleeve and flange attached to the carbon/ carbon shell and (2) a modification intended to relieve the stress. The modification involves the redesign of an inlet connection to incorporate a compressible seal between the Ir/Re liner and the Nb flange. A nickel alloy was selected as the seal material on the basis of its thermal-expansion properties and its ability to withstand the anticipated stresses, including the greatest stresses caused by the high temperatures to be used in brazing during fabrication.

Williams, Brian E.↗