Search NASA⌕ Search

SEARCH · Search NASA

Results for “VAPOR PHASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Catalytic conversion of bio-mass derivable aliphatic alcohols to valuable alkenes or oxygenates

Disclosed is a method for producing, among others, alkenes and/or saturated or unsaturated oxygenates and, which include at least one of an aldehyde and an acid, comprising subjecting the corresponding C3 to C5 aliphatic alcohols that are derivable from biomass, to a vapor phase process over the catalytic system in the presence of a gas mixture of oxygen, air or nitrogen and/or other suitable diluting gas. The catalyst system comprises multi-catalytic zones, in each of which the composition of the co-feed and other reaction parameter can be independently controlled.

Lin, Manhua↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Pt/TiO2

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Platinum on Titania

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Atomic Layer Deposition for Materials-Based H2 Storage: Mg(BH4)2 as a Case Study

To meet the requirements for vehicular solid-state hydrogen (H2) storage, novel materials such as metal borohydrides have increasingly been investigated, in particular, magnesium borohydride (Mg(BH4)2). While these materials have a high H2 capacity (> 14 wt%), poor hydrogenation-dehydrogenation cyclability and material degradation, (e.g., loss of boron), need to be overcome. Prior research has indicated that nano-encapsulation and chemical additives can address these challenges. Therefore, we pursued these two strategies simultaneously with atomic layer deposition (ALD) on Mg(BH4)2. We investigated the use of metal-oxides (e.g., Al2O3, TiO2, CeO2), Pt- group metals (e.g., Pd, Ru) as well as pulsing only one precursor molecule (e.g., Al(CH3)3, BBr3, TiCl4), and assessed these modified Mg(BH4)2 in terms of their H2 storage properties. This presentation will also present the benefits and limitations of using vapor-phase techniques to modify the properties of Mg(BH4)2.

atomic layer deposition↗

Coalescence of GaP on V-Groove Si

In recent years, better understanding and control over the formation of crystalline defects during the direct epitaxy of III-V semiconductors on Si substrates via metal organic vapor phase epitaxy (MOVPE) has enabled large gains in III-V-on-Si solar cell efficiency, pointing to pathway to lower-cost, high-performance III-V solar cells. However, such results have only been achieved on costly chemo-mechanically-polished (CMP) Si wafers. The use of V-groove nanopatterned Si substrates has demonstrated similarly high-crystalline-quality III-V-on-Si epitaxy, but also can be combined with lower-cost polishing techniques. Although they offer a potential cost advantage, growth on V-groove substrates adds challenges not present for epitaxy on planar wafers (the III-V material must be coalesced into a thin film after an initial nucleation stage). MOVPE growth conditions that promote highly facet-selective lateral growth needed for coalescence are generally actively avoided for conventional thin fim growth, so growth conditions need to be re-developed for V-groove-based epitaxy. Additionally, coalescence add complexity to the dislocation dynamics related to lattice relaxation, so strategies used to keep threading dislocation density (TDD) low on planar substrates need to be re-tuned for V-grooves. We have studied the morphological evolution and dislocation dynamics of GaP grown on V-groove Si by MOVPE. Growth conditions of V/III=5,000 and Tg=800 degrees C were uniquely found to produce extremely smooth coalesced thin films, with an RMS roughness of 0.2 nm measured by AFM. Additionally, at this growth condition, we identified two regimes of growth determined by the width of the SiNx cap (a remnant of the nanopatterning process) at the top of the V-grooves. For narrow caps, the GaP coalesces into a thin film, and for wide caps, the GaP evolves into {1 1 1}-faceted diamonds that do not coalesce. We suggest the influence of Si from the sidewalls of the V-grooves on the surface reconstruction of the GaP as the mechanism for this effect, with reflection difference spectroscopy (RDS) and Si doping experiments supporting this theory. In addition to morphology, the dislocation dynamics of the system were studied with electron channeling contrast imaging (ECCI) and transmission electron microscopy (TEM). The TDD of the coalesced GaP films was found to be 5 x 10^7 cm^-2 after coalescence via ECCI, a level still too high for high-quality solar cells. However, misfit dislocations crossing multiple grooves greater than 20 micrometers long were observed in ECCI, suggesting that the V-grooves do not block dislocation glide. TEM prior to and after coalescence was used to distinguish between dislocation creation driven by growth conditions and coalescence. Finally, strategies to reduce the dislocation density to levels acceptable for solar cells will be discussed.

GaP↗

Sustainable Biofuels for Low-Carbon Maritime Transportation

The marine shipping sector heavily depends on fossil fuels and is one of the largest petroleum fuel consumers [1,2]. The annual global marine fuel consumption was estimated to be around 400 million metric tons in 2019 (2.5 billion barrels). Moreover, ocean shipping is one of the most significant contributors to sulfur oxides, nitrogen oxides, and particulate matter emissions. Global shipping contributes 13% of human-caused sulfur emissions and 2.6% of anthropogenic carbon dioxide emissions. As a major source of pollutant emissions, the marine industry faces several challenges related to emission regulations. The International Maritime Organization (IMO) has established a framework for reducing the carbon intensity of shipping: 40% reduction relative to 2008 levels by 2030 and 70% reduction by 2050. As the aviation sector, the maritime shipping sector is difficult to decarbonize through electrification. Biofuels offer the best opportunities for decarbonizing marine shipping in the near and medium-term. Advanced biofuels such as pyrolysis bio-oil offer the low-cost potential for meeting carbon reduction goals. For instance, the pyrolysis bio-oil exhibited promising marginal CO2 abatement costs at less than $100/tonne CO2-equivalent at a heavy fuel oil price greater than $1.10/gal [1]. As a potential biofuel option for low-carbon maritime shipping, this presentation focuses on a comparative techno-economic analysis (TEA) of bio-oils produced via a fast pyrolysis-based conversion pathway. The pathway converts a 50/50 blend of forest residues and clean pine to bio-oil via three process options: fast pyrolysis without vapor upgrading, and fast pyrolysis with vapor phase upgrading over ZSM-5 zeolite catalyst and Pt/TiO2 catalyst. The process configuration and operation variation led to different capital and operating costs, as well as the resulting raw bio-oil’s yield and quality, e.g., the water content, total acid number, and carboxylic acid number. The study also determined the minimum upgrading of bio-oils required to enable blending with very low sulfur fuel oil (VLSFO), with the associated costs reflected in TEA. This study shows that bio-oil could be a cost-effective fuel option for decarbonizing maritime shipping. Further research is required with respect to biofuel blending properties, such as compatibility with existing fuel system infrastructure and suitable engine performance.

BIOMASS FUELS↗

Assessing the Role of Interfacial and Metal Sites in Pt/TiO2-Catalyzed Acetic Acid Hydrodeoxygenation

Thermochemical conversion of biomass to produce drop-in quality biofuels typically involves hydrodeoxygenation (HDO) steps following catalytic fast pyrolysis (CFP) to remove excess oxygen and create a more-stable bio-oil product. HDO reactions are performed by co-feeding the CFP vapor-phase product and H2 gas over a bi-functional catalyst. Noble-metal catalysts supported on reducible metal oxides (e.g., Pt/TiO2) are active and selective toward these HDO reactions. Griffin and co-workers showed that Pt/TiO2 catalysts promote the desired deoxygenation steps for m-cresol HDO while mitigating undesired C-C bond-breaking steps that reduce the overall value/energy density of the biofuel. Such model-compound studies to inform the design of improved catalysts for HDO chemistry are necessary to improve the overall process economics/efficiencies for biofuels production. One important class of bio-derived compounds that has not been studied extensively with respect to HDO chemistry, particularly at the atomic level, is carboxylic acids. Past experimental work indicates that Pt/C and Pt/TiO2 catalysts are selective toward C-C and C-O bond-dissociation products for acetic acid HDO, respectively. To understand the role of Pt/TiO2 active sites in this observed change in selectivity and guide catalyst development, the work in this presentation focuses on modeling the role of Pt-metal and Pt-TiO2-interfacial sites in promoting key C-C bond-breaking, C-O bond-breaking, and (de)hydrogenation steps in acetic acid HDO. Density functional theory (DFT) calculations were performed using the Vienna Ab initio Simulation Package (VASP). The exchange-correlation functional was approximated by the Perdew-Burke-Ernzerhof functional. Dispersion interactions were captured using the D3 method. Projector augmented-wave potentials described electron-ion interactions, and electron wavefunctions were expanded via a planewave basis with an energy cutoff of 500 eV. Activation barriers were calculated using the climbing image nudged elastic band method. Results and Discussion: To discern the role of Pt-metal and Pt-TiO2 interface sites in promoting acetic acid HDO chemistry, Pt(111) slab and anatase TiO2(101)-supported Pt-nanowire (PtNW/OH-TiO2) surface models were constructed, respectively. Because H2 is co-fed in HDO reactions, the anatase support was terminated with OH groups. Interfacial vacancies have been shown to facilitate Ru/TiO2-catalyzed phenol HDO; thus, an interfacial model with an OH vacancy was also considered (PtNW/OHv-TiO2). Pt-TiO2-interface sites stabilize adsorption of all studied acetic acid HDO surface intermediates relative to terrace Pt-metal sites, particularly when an interfacial-OH vacancy is present. Oxygenated species prefer to bind at the OH vacancy through the O atom, suggesting a preference for C-O over C-C bond cleavage at these sites. This hypothesis is supported by net-negative and net-positive average shifts in the reaction energy and activation energy barriers for C-O and C-C bond-breaking steps, respectively, at Pt-TiO2-interface sites relative to Pt-metal sites. Using the calculated energetics, the predicted minimum-energy pathway was determined for each surface. Pt(111) is predicted to follow decarboxylation, producing undesired methane and carbon dioxide. Conversely, PtNW/OH-TiO2 and PtNW/OHv-TiO2 are both predicted to produce desired acetaldehyde and ethane. The interfacial vacancy may also play a key role in facilitating the first C-O bond-breaking step in acetic acid HDO, lowering the barrier by 0.6 eV relative to the defect-free interface model. These results demonstrate the critical role of the Pt-TiO2 interface in the shift in acetic acid HDO selectivity experimentally observed on Pt/C and Pt/TiO2 catalysts. The results herein demonstrate the important role of the Pt-TiO2 interface and interfacial oxygen vacancies in improving the carbon efficiency for HDO reactions in CFP upgrading.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Silylated Co/SBA-15 catalysts for Fischer-Tropsch synthesis

A series of silylated Co/SBA-15 catalysts were prepared via the reaction of surface Si-OH of SBA-15 with hexamethyldisilazane (HMDS) under anhydrous, vapor-phase conditions, and then characterized by FT-IR, N{sub 2} physisorption, TG, XRD, and TPR-MS. The results showed that organic modification led to a silylated SBA-15 surface composed of stable hydrophobic Si-(CH{sub 3}){sub 3} species even after calcinations and H{sub 2} reduction at 673 K. Furthermore, the hydrophobic surface strongly influenced both metal dispersion and reducibility. Compared with non-silylated Co/SBA, Co/S-SBA (impregnation after silylation) showed a high activity, due to the better cobalt reducibility on the hydrophobic support. However, S-Co/SBA (silylation after impregnation) had the lowest FT activity among all the catalysts, due to the lower cobalt reducibility along with the steric hindrance of grafted -Si(CH{sub 3}){sub 3} for the re-adsorption of {alpha}-olefins. -- Graphical abstract: The silylation of an SBA-15 before cobalt impregnation enhanced the reducibility of cobalt oxides on an SBA-15-supported cobalt catalyst and consequently increased the catalytic activity for Fischer-Tropsch synthesis. Display Omitted

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Salt Disposal Investigations to Study Thermally Hot Radioactive Waste In A Deep Geologic Repository in Bedded Rock Salt - 12488

A research program is proposed to investigate the behavior of salt when subjected to thermal loads like those that would be present in a high-level waste repository. This research would build upon results of decades of previous salt repository program efforts in the US and Germany and the successful licensing and operation of a repository in salt for disposal of defense transuranic waste. The proposal includes a combination of laboratory-scale investigations, numerical simulations conducted to develop validated models that could be used for future repository design and safety case development, and a thermal field test in an underground salt formation with a configuration that replicates a small portion of a conceptual repository design. Laboratory tests are proposed to measure salt and brine properties across and beyond the range of possible repository conditions. Coupled numerical models will seek to describe phenomenology (thermal, mechanical, and hydrological) observed in the laboratory tests. Finally, the field test will investigate many phenomena that have been variously cited as potential issues for disposal of thermally hot waste in salt, including buoyancy effects and migration of pre-existing trapped brine up the thermal gradient (including vapor phase migration). These studies are proposed to be coordinated and managed by the Carlsbad Field Office of DOE, which is also responsible for the operation of the Waste Isolation Pilot Plant (WIPP) within the Office of Environmental Management. The field test portion of the proposed research would be conducted in experimental areas of the WIPP underground, far from disposal operations. It is believed that such tests may be accomplished using the existing infrastructure of the WIPP repository at a lower cost than if such research were conducted at a commercial salt mine at another location. The phased field test is proposed to be performed over almost a decade, including instrumentation development, several years of measurements during heating and then subsequent cooling periods, and the eventual forensic mining back of the test bed to determine the multi-year behavior of the simulated waste/rock environment. Funding possibilities are described, and prospects for near term start-up are discussed. Mining of the access drifts required to create the test area in the WIPP underground began in November 2011. Because this mining uses existing WIPP infrastructure and labor, it is estimated to take about two years to complete the access drifts. WIPP disposal operations and facility maintenance activities will take priority over the SDI field test area mining. Funding of the SDI proposal was still being considered by DOE's Offices of Environmental Management and Nuclear Energy at the time this paper was written, so no specific estimates of the progress in 2012 have been included. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Radiological Performance Modeling: Platform Comparison

Zapadnoe Uranium Mill Tailings Site, Pridneprovsky Chemical Plant Ukraine: Two exposure scenarios were utilized to develop performance assessment models in GoldSim and NORMALYSA. The first scenario is an onsite worker exposed to radioactivity through external ground irradiation as well as radon and radioactive dust inhalation. The second being an offsite Resident 300 years after institutional control exposed through the ingestion of garden vegetables irrigated by contaminated ground water, ingestion of fish from Konoplyanka River, and agricultural activities in contaminated garden. NORMALYSA utilizes a modular interface to connect extensive pre-created modules to develop contaminant transport and risk assessment models for safety assessments and performance assessments at NORM and legacy sites. Developed by Facilia AB, the program was tested with the creation of the Zapadnoe model under the International Atomic Energy Agency MODARIA Il Working Group 1 (WG1). Default values are provided for input parameters where site specific data and distributions lack. Probabilistic simulations and inputs are limited to parameters with assigned Gaussian probability functions. Similar results for transient worker inhalation dose were found in comparison with the Zapadnoe GoldSim model. However, the NORMALYSA model has results larger by an order of magnitude for external radiation in the transient worker and for aquatic food ingestion, inhalation, and garden food ingestion to the resident. Performance Assessment Modeling: Radiological performance models promote good management and support in remediation and environmental decision making by optimizing radioactive waste disposal site performance. a performance assessment model of the Zapadnoe uranium mill tailings site and a model for calculating authorized limits at Los Alamos National Laboratory are created to demonstrate and highlight the respective capabilities of three modeling platforms: GoldSim, NORMALYSA, and RESRAD-Onsite. GoldSim is a general-purpose modeling platform with the ability to simulate site-specific FT radionuclide transport and risk assessment using a graphical interface to create and link elements that act as indivisible building blocks of the model. The Zapadnoe performance assessment model created in GoldSim is composed of input parameters collected from site specific parameters from WG1 as well as standard assumptions seen in the Generic PA Model from Neptune and Company. The multivariate Zapadnoe simulation contains both deterministic and probabilistic simulation capabilities with the ability to quantitatively represent the uncertainty and associated risks of the site via the Monte Carlo simulation method. Model parameters, documentation, and assumptions are built directly into the model creating a transparent, reproducible, and more purposeful site specific model. To demonstrate this, an ingestion of water pathway was included in addition to the exposure pathways included in the NORMALYSA model. GoldSim offers a wide variety of probability distributions to choose from as well as many tools to visualize the uncertainty of the models and explore which pathways and radionuclides dominate dose. In contrast to the NORMALYSA model, the GoldSim model uses dynamic simulation to calculate tritium concentrations. Authorized limits support the evaluation of radiological health effects from radionuclides present in bulk contaminated soil in order to assist in the process of clearing land for release under different uses. Calculations of authorized limits in RESRAD-Onsite and GoldSim models support the evaluation for 15 radionuclides using a residential exposure scenario, indoor and outdoor inhalation of dust and vapor phase radionuclides (tritium), incidental soil ingestion, and ingestion grown fruits and Vegetables. RESRAD-Onsite, developed by Argonne National Laboratory is a dedicated computer code for calculating radiation doses and cancer risks to an individual located on top of radioactively contaminated soils. It can also be used to provide guidelines for deriving radionuclide soil levels corresponding to a specific dose criterion. The menu driven user interface facilitates selection of radionuclides and soil concentrations, as well as defines parameter values related to materials, environmental factors, and exposure pathways. The program contains radionuclide-specific data such as dose conversion factors and risk coefficients, as well as soil-water partition coefficients and transfer factors for biotic media. The GoldSim model successfully emulates the RESRAD-Onsite code using identical radiological decay and ingrowth factors, radiation dose conversion factors, and other input parameters. DE EEDE ETS Each model supports dynamic modeling of radionuclide ingrowth and decay over time, and integrate this capability with the transport of radionuclides in the environment via processes such as advection and/or diffusion in fluids, or within porous solid media, The applicability of each program is heavily dependent on project context. In the context of developing Authorized Limits, RESRAD-Onsite may be a more desirable option as it was developed for this particular application. For simple disposal or legacy sites or sites that do not need site-specific model structure, NORMALYSA may be a desirable modeling platform, GoldSim can be used to model any problem for which RESRAD or NORMALYSA is applicable, but its strength lies in its flexibility, analytical, and probabilistic capabilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Review of Modeling Approaches for Predicting Frost Growth and Defrosting on Tube-Fin Heat Exchangers: Preprint

Frost formation and growth on the evaporator surface is a common process that deteriorates the air-refrigerant heat transfer and restricts airflow. This degrades the performance of the vapor compression system by increasing temperature lift and air-side pressure drop. To accurately predict these effects during coil frosting, as well as the energy use and duration of the defrost process, there is a need to estimate the heat and mass transfer, momentum transport, and solid-liquid and liquid-vapor phase change. Therefore, in the past few decades, continuous effort has been made to model frosting and defrosting processes using approaches ranging from empirical correlations to computational fluid dynamic models. To provide a clearer overview for researchers, engineers, and manufacturers in this field, this paper provides a comprehensive literature review for frosting and defrosting models. The paper begins with theoretical background of frost formation and defrost processes, and then reviews the common modeling approaches in literature and their underlying assumptions when trying to account for various physical phenomenon. Based on the literature review, the most critical modeling effort for frost formation is the determination of frost densification rate and frost growth rate. Various methods to predict these two parameters are reviewed. Empirical correlations commonly used for frost density and thermal conductivity are presented and compared. For the defrost process, various multi-stage models have been proposed with different assumptions. Some assume the presence of air gap between the tube wall and the frost, while others consider the melted frost flow due to gravity. We also review physics-based and empirical approaches to integrate defrost models into heat pump models. We conclude by identifying research gaps and providing recommendations.

defrost↗

Condensation-based redox flow battery rebalancing

In a redox flow battery (RFB), the base solvent of the electrolytes tends to migrate across the barrier layer from one electrode toward the other. This can result in a volume and concentration imbalance between the electrolytes that is detrimental to battery efficiency and capacity. Compatible electrolytes can be mixed to rebalance the system, but for incompatible electrolytes mixing is not a viable option. To this end, the RFB herein includes a separator that recovers base solvent from the vapor phase of one of the electrolytes and returns the recovered base solvent to the other electrolyte to thereby reverse the imbalance.

Saraidaridis, James D.↗

Development of a rate-based ENRTL-RK process model for a water-lean solvent

Advanced water-lean solvents (WLS) for post-combustion CO2 capture offer several advantages over the aqueous amine solvents . WLS have lower parasitic energy penalty, lower corrosion, lower temperature and high-pressure CO2 regeneration leading to lower cost of CO2 capture. RTI International, with funding from the US Department of Energy, has been developing its novel water-lean solvent, that has shown specific reboiler duty of 2.3 GJ/t-CO2 at the 60-kWe pilot testing unit (Tiller Plant, SINTEF, Norway) and 2.6 GJ/t-CO2 at the engineering scale testing system (12 MWe) at the Technology Centre Mongstad (TCM) in Norway. All heat duties, including the one from TCM testing, were consistent with Aspen Plus modeling of the specific configuration of each test plant. This work focuses on the development of a detailed process model using in-house laboratory measurements and process data at pilot scale. The eNTRL-RK model used in this work is based on an unsymmetric activity coefficient model with the reference states chosen to be pure liquids for solvents and ideal dilute solution at unit solute molality (resulting in activity coefficient of unity at infinite dilution) for electrolytes. It uses the Redlich-Kwong equation of state for vapor phase properties and Henry’s law for solubility of supercritical gases. The model was validated using process data from the pilot-scale campaign at the Tiller plant, and the engineering scale test campaign at TCM. Data on CO2 capture rate, absorber, and regenerator temperature profiles and specific reboiler duties from two different test campaigns at Tiller and TCM, were used to further refine and validate the model and the model compares favorably to experimental data. The validation results against TCM campaign will be presented in this work.

CO2 capture↗

Method of fabricating an optoelectronic device having a bulk heterojunction

A method of fabricating an organic optoelectronic device having a bulk heterojunction comprises the steps of: depositing a first layer over a first electrode by organic vapor phase deposition, wherein the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer, wherein the interface of the second layer on the first layer forms a bulk heterojunction; and depositing a second electrode over the second layer to form the optoelectronic device. In another embodiment, a first layer having protrusions is deposited over the first electrode, wherein the first layer comprises a first organic small molecule material. For example, when the first layer is an electron donor layer, the first electrode is an anode, the second layer is an electron acceptor layer, and the second electrode is a cathode. As a further example, when the first layer is an electron acceptor layer, the first electrode is a cathode, the second layer is an electron donor layer, and the second electrode is an anode.

36 MATERIALS SCIENCE↗

Method of fabricating an optoelectronic device having a bulk heterojunction

A method of fabricating an optoelectronic device comprises: depositing a first layer having protrusions over a first electrode, in which the first layer comprises a first organic small molecule material; depositing a second layer on the first layer such that the second layer is in physical contact with the first layer; in which the smallest lateral dimension of the protrusions are between 1 to 5 times the exciton diffusion length of the first organic small molecule material; and depositing a second electrode over the second layer to form the optoelectronic device. A method of fabricating an organic optoelectronic device having a bulk heterojunction is also provided and comprises: depositing a first layer with protrusions over an electrode by organic vapor phase deposition; depositing a second layer on the first layer where the interface of the first and second layers forms a bulk heterojunction; and depositing another electrode over the second layer.

36 MATERIALS SCIENCE↗

Vapor-induced phase-separation-enabled versatile direct ink writing

Abstract Versatile printing of polymers, metals, and composites always calls for simple, economic approaches. Here we present an approach to three-dimensional (3D) printing of polymeric, metallic, and composite materials at room conditions, based on the polymeric vapor-induced phase separation (VIPS) process. During VIPS 3D printing (VIPS-3DP), a dissolved polymer-based ink is deposited in an environment where nebulized non-solvent is present, inducing the low-volatility solvent to be extracted from the filament in a controllable manner due to its higher chemical affinity with the non-solvent used. The polymeric phase is hardened in situ as a result of the induced phase separation process. The low volatility of the solvent enables its reclamation after the printing process, significantly reducing its environmental footprint. We first demonstrate the use of VIPS-3DP for polymer printing, showcasing its potential in printing intricate structures. We further extend VIPS-3DP to the deposition of polymer-based metallic inks or composite powder-laden polymeric inks, which become metallic parts or composites after a thermal cycle is applied. Furthermore, spatially tunable porous structures and functionally graded parts are printed by using the printing path to set the inter-filament porosity as well as an inorganic space-holder as an intra-filament porogen.

42 ENGINEERING↗

Third-harmonic generation in phase-matched Rb vapor.

The generation of 0.3547-micron radiation was performed by tripling 1.064-micron radiation in a phase-matched mixture of rubidium vapor and xenon. A third-harmonic nonlinear susceptibility in Rb vapor is confirmed. It is about 100,000 times greater than that of He. This large susceptibility is due to the large oscillator strengths and resonant enhancements resulting from Rb transitions in the near infrared, visible, and UV.

Young, J. F.↗

Improving biomass pyrolysis economics by integrating vapor and liquid phase upgrading

Partial deoxygenation of bio-oil by catalytic fast pyrolysis with subsequent coupling and hydrotreating can lead to improved economics and will aid commercial deployment of pyrolytic conversion of biomass technologies. Biomass pyrolysis efficiently depolymerizes and deconstructs solid plant matter into carbonaceous molecules that, upon catalytic upgrading, can be used for fuels and chemicals. Upgrading strategies include catalytic deoxygenation of the vapors before they are condensed (in situ and ex situ catalytic fast pyrolysis), or hydrotreating following condensation of the bio-oil. In general, deoxygenation carbon efficiencies, one of the most important cost drivers, are typically higher for hydrotreating when compared to catalytic fast pyrolysis alone. However, using catalytic fast pyrolysis as the primary conversion step can benefit the entire process chain by: (1) reducing the reactivity of the bio-oil, thereby mitigating issues with aging and transport and eliminating need for multi-stage hydroprocessing configurations; (2) producing a bio-oil that can be fractionated through distillation, which could lead to more efficient use of hydrogen during hydrotreating and facilitate integration in existing petroleum refineries; and (3) allowing for the separation of the aqueous phase. In this perspective, we investigate in detail a combination of these approaches, where some oxygen is removed during catalytic fast pyrolysis and the remainder removed by downstream hydrotreating, accompanied by carbon–carbon coupling reactions in either the vapor or liquid phase to maximize carbon efficiency toward value-driven products (e.g. fuels or chemicals). The economic impact of partial deoxygenation by catalytic fast pyrolysis will be explored in the context of an integrated two-stage process. In conclusion, improving the overall pyrolysis-based biorefinery economics by inclusion of production of high-value co-products will be examined.

09 BIOMASS FUELS↗