Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Integration time required to extract accurate static and dynamic data from transonic wind-tunnel tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for 'static' aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency content of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency band width used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 sec; static pressure tests, 0.1 sec; flutter tests, 30 to 60 sec; and random-dynamic tests, 10 sec.

Muhlstein, L., Jr.↗

Synthesis of rotor test data for real-time simulation

A mathematical model of a hingeless tilting rotor is presented. The model was obtained by a systematic curve fit procedure applied to an extensive set of model scale wind tunnel data. The math model equations were used in a real time flight simulation model of a hingeless tilt rotor XV-15 to assess changes in flying qualities compared to those obtained using a previous rotor model. Extensive plots of the rotor derivatives are given. Discussions of attempts to apply multivariable linear regression technqiues to the data and the use of an analytical rotor representation are included.

Mcveigh, M. A.↗

Viscous pumping and the spin-down of thermospheric gyres and jets

Strong gyres and jets can be generated at auroral latitudes in the thermosphere by enhanced electric fields during geomagnetic substorms. Typical height profiles of ion density suggest that the ion drag force should generate large curvature in the vertical profile of the winds in the highly viscous region of the thermosphere above about 200 km. It is proposed that the poststorm spin-down of these gyres and jets proceeds via Ekman circulations driven by the curvatures in the height profiles of the winds. Analytic and numerical calculations of the ageostrophic winds forced by curvature in model geostrophic wind profiles show that the ageostrophic wind speeds and directions depend mainly on the kinematic viscosity in the region of curvature and the total change in shear in the geostrophic wind. Ageostrophic wind speeds for typical thermospheric jets can exceed 200 m/s (about 50 percent of the jet winds). Spin-down times of thermospheric jets and cyclonic gyres by the Ekman pumping mechanism are estimated at less than about 6 hours.

Walterscheid, R. L.↗

Prediction of the effects of propeller operation on the static longitudinal stability of single-engine tractor monoplanes with flaps retracted

The effects of propeller operation on the static longitudinal stability of single-engine tractor monoplanes are analyzed, and a simple method is presented for computing power-on pitching-moment curves for flap-retracted flight conditions. The methods evolved are based on the results of powered-model wind-tunnel investigations of 28 model configurations. Correlation curves are presented from which the effects of power on the downwash over the tail and the stabilizer effectiveness can be rapidly predicted. The procedures developed enable prediction of power-on longitudinal stability characteristics that are generally in very good agreement with experiment.

Weil, Joseph↗

Integration Time Required to Extract Accurate Data from Transonic Wind-Tunnel Tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for static aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency bandwidth used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 s; static pressure tests, 1 s; flutter tests, 30 to 60 s; and random-dynamic tests, 10 s.

Muhlstein, Lado, Jr.↗

The American WAKE experimeNt (AWAKEN): Groundbreaking International Field Research Addresses Wind Farm Atmosphere Interactions

To help provide that understanding, the U.S. Department of Energy's (DOE's) Wind Energy Technologies Office (WETO) funds the American WAKE experimeNt (AWAKEN). AWAKEN is an international, multi-institutional wind energy field campaign designed to answer the most pressing science questions about the impacts of wind turbine wake effects. From 2022 to 2024, AWAKEN will gather observational data about the atmosphere around and within operational wind farms, validate wind farm models, and advance understanding of wind farm behavior.

AWAKEN↗

Validation of Numerical Models of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Against Full-Scale Measurements Within OC5 Phase III

The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison of simulated results to the response data of physical systems. Phase III of the OC5 project validates OWT models against the measurements recorded on a Senvion 5M wind turbine supported by the OWEC Quattropod from the alpha ventus offshore wind farm. The following operating conditions of the wind turbine were chosen for the validation: (1) idling below the cut-in wind speed, (2) rotor-nacelle assembly (RNA) rotation maneuver below the cut-in wind speed, (3) power production below and above the rated wind speed, and (4) shutdown. A number of validation load cases were defined based on these operating conditions. The following measurements were used for validation: (1) strains and accelerations recorded on the support structure and (2) pitch, yaw, and azimuth angles, generator speed, and electrical power recorded from the RNA. Strains were not directly available from the majority of the OWT simulation tools; therefore, strains were calculated based on out-of-plane bending moments, axial forces, and cross-sectional properties of the structural members. The simulation results and measurements were compared in terms of time series, discrete Fourier transforms, power spectral densities, and probability density functions of strains and accelerometers. A good match was achieved between the measurements and models setup by OC5 Phase III participants.

17 WIND ENERGY↗

Beyond Basic Drag in Interplanetary CME Modeling: Effects of Solar Wind Pileup and High-Speed Streams

Coronal mass ejections (CMEs) cause severe space weather effects throughout our solar system. As a fast CME propagates through interplanetary space, it accumulates solar wind materials at its front. This pileup of materials, or CME-driven sheath, can be important in determining the geoeffectiveness of a CME. We take an existing arrival time model that includes expansion and deformation of the CME flux rope (ANTEATR; Kay & Gopalswamy, 2018, https://doi.org/10.1029/2018JA025780; Kay & Nieves-Chinchilla, 2021a, https://doi.org/10.1029/2020JA028911) and add a pileup procedure (PUP) as a physics-based approach to modeling the CME-driven sheath. ANTEATR-PUP solves the Rankine-Hugoniot equations for an oblique shock to determine the shock speed and sheath density, magnetic field, and temperature. The extra sheath mass affects the background drag calculation. Additionally, ANTEATR can now use any 1D profile for the background solar wind as opposed to the simple empirical models it previously relied upon. We present initial results from ANTEATR-PUP and compare with previous ANTEATR findings. Using results from an MHD simulation, we explore the effects of interactions with a static high-speed stream (HSS) on the CME's and sheath's interplanetary evolution. The drag forces essentially disappear while a CME remains within the HSS, but reappear stronger once the CME exits. The HSS-CME interaction produces the largest changes in the CME and sheath properties at 1 au when it occurs either close to the Sun near the inner simulation boundary at 0.1 au or right before the CME reaches 1 au. We estimate that these changes could significantly affect the geoeffectiveness.

C Kay↗

Gottingen Wind Tunnel for Testing Aircraft Models

Given here is a brief description of the Gottingen Wind Tunnel for the testing of aircraft models, preceded by a history of its development. Included are a number of diagrams illustrating, among other things, a sectional elevation of the wind tunnel, the pressure regulator, the entrance cone and method of supporting a model for simple drag tests, a three-component balance, and a propeller testing device, all of which are discussed in the text.

Prandtl, L↗

Infrared Images of Boundary Layer Transition on the D8 Transport Configuration in the LaRC 14- by 22-Foot Subsonic Tunnel

Grit, trip tape, or trip dots are routinely applied on the leading-edge regions of the fuselage, wings, tails or nacelles of wind tunnel models to trip the flow from laminar to turbulent. The thickness of the model's boundary layer is calculated for nominal conditions in the wind tunnel test to determine the effective size of the trip dots, but the flow over the model may not transition as intended for runs with different flow conditions. Temperature gradients measured with an infrared camera can be used to detect laminar to turbulent boundary layer transition on a wind tunnel model. This non-intrusive technique was used in the NASA Langley 14- by 22-Foot Subsonic Tunnel to visualize the behavior of the flow over a D8 transport configuration model. As the flow through the wind tunnel either increased to or decreased from the run conditions, a sufficient temperature difference existed between the air and the model to visualize the transition location (due to different heat transfer rates through the laminar and the turbulent boundary layers) for several runs in this test. Transition phenomena were visible without active temperature control in the atmospheric wind tunnel, whether the air was cooler than the model or vice-versa. However, when the temperature of the model relative to the air was purposely changed, the ability to detect transition in the infrared images was enhanced. Flow characteristics such as a wing root horseshoe vortex or the presence of fore-body vortical flows also were observed in the infrared images. The images of flow features obtained for this study demonstrate the usefulness of current infrared technology in subsonic wind tunnel tests.

Mason, Michelle L.↗

ExaWind: Exascale Predictive Wind Plant Flow Physics Modeling

The scientific goal of the ExaWind project is to advance our fundamental understanding of the flow physics governing whole wind plant performance, including wake formation, complex terrain impacts, and turbine-turbine-interaction effects. The primary application codes in the ExaWind environment are Nalu-Wind, an unstructured-grid computational fluid dynamics (CFD) code, AMR-Wind, a structured-grid CFD code, and OpenFAST, a whole-turbine simulation code. In this poster we present our progress towards simulating the ExaWind challenge problem, which is a predictive simulation of a wind farm with tens of megawatt-scale wind turbines dispersed over an area of 50 square kilometers.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

Electrodynamic effects of thermospheric winds from the NCAR thermospheric general circulation model

Electrodynamic effects of thermospheric winds simulated with the NCAR thermospheric general circulation model (TGCM) were modeled and compared with observations for equinox solar minimum conditions. Two TGCM wind simulations were used: one driven only by in situ solar UV heating, the other also including lower boundary forcing that mimics the effects of upward propagating semidiurnal tides. It was found that, without tidal forcing, the TGCM winds produce ground magnetic variations that have the general pattern of observed Sq variations, but are only about half as strong. The addition of tidal forcing improved the agreement between calculated and observed magnetic variations and between calculated and observed electric fields.

Richmond, A. D.↗

NREL's Balance-of-System Cost Model for Land-Based Wind

NREL's Land-based Balance of System Systems Engineering (LandBOSSE) model is a tool for modeling the balance of system (BOS) costs of land-based wind plants. BOS costs currently account for approximately 30% of the capital expenditures needed to install a land-based wind plant and include all costs associated with installing a wind plant, such as permitting, labor, material, and equipment costs associated with site preparation, foundation construction, electrical infrastructure, and tower installation. NREL developed LandBOSSE after identifying a need for a hybrid of process-based and empirically derived model that can provide flexibility for assessing wind plant BOS costs at a system level. NREL's prior BOS models have relied on empirical fits of legacy industry data, which limit their predictive ability. LandBOSSE, however, was designed to help users explore tradeoffs between innovative design scenarios while balancing the level of detail and speed required for model execution. The model was developed using a hybrid of process-based and empirically derived methods to create a modular model design that will allow for updates as wind energy technology evolves. The goal of LandBOSSE is to allow researchers, analysts, wind power developers, government agencies, and the public to explore how BOS may vary for different wind plant designs.

17 WIND ENERGY↗

A model of rotationally-sampled wind turbulence for predicting fatigue loads in wind turbines

Empirical equations are presented with which to model rotationally-sampled (R-S) turbulence for input to structural-dynamic computer codes and the calculation of wind turbine fatigue loads. These equations are derived from R-S turbulence data which were measured at the vertical-plane array in Clayton, New Mexico. For validation, the equations are applied to the calculation of cyclic flapwise blade loads for the NASA/DOE Mod-2 2.5-MW experimental HAWT's (horizontal-axis wind turbines), and the results compared to measured cyclic loads. Good correlation is achieved, indicating that the R-S turbulence model developed in this study contains the characteristics of the wind which produce many of the fatigue loads sustained by wind turbines. Empirical factors are included which permit the prediction of load levels at specified percentiles of occurrence, which is required for the generation of fatigue load spectra and the prediction of the fatigue lifetime of structures.

Spera, David A.↗

LIDAR Wind Speed Measurements of Evolving Wind Fields

Light Detection and Ranging (LIDAR) systems are able to measure the speed of incoming wind before it interacts with a wind turbine rotor. These preview wind measurements can be used in feedforward control systems that are designed to reduce turbine loads. However, the degree to which such preview-based control techniques can reduce loads by reacting to turbulence depends on how accurately the incoming wind field can be measured. Past studies have assumed the validity of physicist G.I. Taylor's 1938 frozen turbulence hypothesis, which implies that turbulence remains unchanged as it advects downwind at the mean wind speed. With Taylor's hypothesis applied, the only source of wind speed measurement error is distortion caused by the LIDAR. This study introduces wind evolution, characterized by the longitudinal coherence of the wind, to LIDAR measurement simulations using the National Renewable Energy Laboratory's (NREL's) 5-megawatt turbine model to create a more realistic measurement model. A simple model of wind evolution was applied to a frozen wind field that was used in previous studies to investigate the effects of varying the intensity of wind evolution. LIDAR measurements were also evaluated using a large eddy simulation (LES) of a stable boundary layer that was provided by the National Center for Atmospheric Research. The LIDAR measurement scenario investigated consists of a hub-mounted LIDAR that scans a circle of points upwind of the turbine in order to estimate the wind speed component in the mean wind direction. Different combinations of the preview distance that is located upwind of the rotor and the radius of the scan circle were analyzed. It was found that the dominant source of measurement error for short preview distances is the detection of transverse and vertical wind speeds from the line-of-sight LIDAR measurement. It was discovered in previous studies that, in the absence of wind evolution, the dominant source of error for large preview distances is the spatial averaging caused by the LIDAR's sampling volume. However, by introducing wind evolution, the dominant source of error for large preview distances was found to be the coherence loss caused by evolving turbulence. Different measurement geometries were compared using the bandwidth for which the measurement coherence remained above 0.5 and also the area under the measurement coherence curve. Results showed that, by increasing the intensity of wind evolution, the measurement coherence decreases. Using the coherence bandwidth metric, the optimal preview distance for a fixed-scan radius remained almost constant for low and moderate amounts of wind evolution. For the wind field with the simple wind evolution model introduced, the optimal preview distance for a scan radius of 75% blade span (47.25 meters) was found to be 80 meters. Using the LES wind field, the optimal preview distance was 65 meters. When comparing scan geometries using the area under the coherence curve, results showed that, as the intensity of wind evolution increases, the optimal preview distance decreases.

17 WIND ENERGY↗

Use of wind data in global modelling

The European Centre for Medium Range Weather Forecasts (ECMWF) is producing operational global analyses every 6 hours and operational global forecasts every day from the 12Z analysis. How the wind data are used in the ECMWF golbal analysis is described. For each current wind observing system, its ability to provide initial conditions for the forecast model is discussed as well as its weaknesses. An assessment of the impact of each individual system on the quality of the analysis and the forecast is given each time it is possible. Sometimes the deficiencies which are pointed out are related not only to the observing system itself but also to the optimum interpolation (OI) analysis scheme; then some improvements are generally possible through ad hoc modifications of the analysis scheme and especially tunings of the structure functions. Examples are given. The future observing network over the North Atlantic is examined. Several countries, coordinated by WMO, are working to set up an 'Operational WWW System Evaluation' (OWSE), in order to evaluate the operational aspects of the deployment of new systems (ASDAR, ASAP). Most of the new systems are expected to be deployed before January 1987, and in order to make the best use of the available resources during the deployment phase, some network studies are carried out at the present time, by using simulated data for ASDAR and ASAP systems. They are summarized.

Pailleux, J.↗