Search NASA⌕ Search

SEARCH · Search NASA

Results for “depth profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

SU-E-T-756: Tissue Inhomogeneity Corrections in Intra-Operative Radiotherapy

Purpose: Investigate the impact of tissue inhomogeneities on dose distributions produced by low-energy X-rays in intra-operative radiotherapy (IORT). Methods: A 50-kV INTRABEAM X-ray device with superficial (Flat and Surface) applicators was commissioned at our institution. For each applicator, percent depth-dose (PDD), dose-profiles (DP) and output factors (OF) were obtained. Calibrated GaFchromic (EBT3) films were used to measure dose distributions in solid water phantom at various depths (2, 5, 10, and 15 mm). All recommended precautions for film-handling, film-exposure and scanning were observed. The effects of tissue inhomogeneities on dose distributions were examined by placing air-cavities and bone and tissue equivalent materials of different density (ρ), atomic number (Z), and thickness (t = 0–4mm) between applicator and film detector. All inhomogeneities were modeled as a cylindrical cavity (diameter 25 mm). Treatment times were calculated to deliver 1Gy dose at 5mm depth. Film results were verified by repeat measurements with a thin-window parallel plate ion-chamber (PTW 34013A) in a water tank. Results: For a Flat-4cm applicator, the measured dose rate at 5mm depth in solid water was 0.35 Gy/min. Introduction of a cylindrical air-cavity resulted in an increased dose past the inhomogeneity. Compared to tissue equivalent medium, dose enhancement due to 1mm, 2mm, 3mm and 4mm air cavities was 10%, 16%, 24%, and 35% respectively. X-ray attenuation by 2mm thick cortical bone resulted in a significantly large (58%) dose decrease. Conclusion: IORT dose calculations assume homogeneous tissue equivalent medium. However, soft X-rays are easily affected by non-tissue equivalent materials. The results of this study may be used to estimate and correct IORT dose delivered in the presence of tissue inhomogeneities.

60 APPLIED LIFE SCIENCES↗

SU-F-T-83: Infant Total Skin Electron Therapy Using Five Fields Technique

Purpose: We were presented with a 9 month old boy with Relapsed Acute Myeloid Leukemia (AML) involving the skin. The plan was to treat the entire skin using 6 MeV electrons with the infant under complete anesthesia. The purpose of this work is to commission the 6 MeV electron beam and to develop a technique that can be used to deliver total skin dose to infants with minimal patient immobilization. Methods: A baby mannequin phantom that mimics the child’s length was used to determine the best technique to treat the infant. The 76 cm long phantom was placed on the floor. The phantom was placed in four unique immobilization devices to simulate four different treatment positions (anterior, posterior, left lateral and right lateral). Radiochromic films were used to determine beam profile in both axial and radial directions, and percent depth dose (PDD). Absolute calibration of the machine output at 214 cm distance was measured using an Exradin A11 parallel-plate ion chamber. A 1.0 cm plexiglass scatter plate was inserted in the collimator. Mosfet dosimeters were used for dose verification for phantom and and patient. Results: At 214 cm source to surface distance (SSD) using gantry angle of + 20o from vertical beam flatness is + 10% in the radial direction over a region of 70 cm and + 4% in the axial direction over 60 cm. A five field arrangement was determined to optimally deliver the desired dose with > 90% uniformity. The fifth field was used to boost the head vertex. Conclusion: It is possible to treat sedated infants with total skin dose using five positions. Four positions were enough to cover the body and the fifth position boosts the vertex of the head. All fractions can be reproduced accurately daily because of the patient’s stable immobilization.

60 APPLIED LIFE SCIENCES↗

Beam characteristics of energy-matched flattening filter free beams

Purpose: Flattening filter free (FFF) linear accelerators can increase treatment efficiency and plan quality. There are multiple methods of defining a FFF beam. The Elekta control system supports tuning of the delivered FFF beam energy to enable matching of the percentage depth-dose (PDD) of the flattened beam at 10 cm depth. This is compared to FFF beams where the linac control parameters are identical to those for the flattened beam. All beams were delivered on an Elekta Synergy accelerator with an Agility multi-leaf collimator installed and compared to the standard, flattened beam. The aim of this study is to compare “matched” FFF beams to both “unmatched” FFF beams and flattened beams to determine the benefits of matching beams. Methods: For the three modes of operation 6 MV flattened, 6 MV matched FFF, 6 MV unmatched FFF, 10 MV flattened, 10 MV matched FFF, and 10 MV unmatched FFF beam profiles were obtained using a plotting tank and were measured in steps of 0.1 mm in the penumbral region. Beam penumbra was defined as the distance between the 80% and 20% of the normalized dose when the inflection points of the unflattened and flattened profiles were normalized with the central axis dose of the flattened field set as 100%. PDD data was obtained at field sizes ranging from 3 cm × 3 cm to 40 cm × 40 cm. Radiation protection measurements were additionally performed to determine the head leakage and environmental monitoring through the maze and primary barriers. Results: No significant change is made to the beam penumbra for FFF beams with and without PDD matching, the maximum change in penumbra for a 10 cm × 10 cm field was within the experimental error of the study. The changes in the profile shape with increasing field size are most significant for the matched FFF beam, and both FFF beams showed less profile shape variation with increasing depth when compared to flattened beams, due to consistency in beam energy spectra across the radiation field. The PDDs of the FFF beams showed less variation with field size, the d{sub max} value was deeper for the matched FFF beam than the FFF beam and deeper than the flattened beam for field sizes greater than 5 cm × 5 cm. The head leakage when using the machine in FFF mode is less than half that for a flattened beam, but comparable for both FFF modes. The radiation protection dose-rate measurements show an increase of instantaneous dose-rates when operating the machines in FFF mode but that increase is less than the ratio of MU/min produced by the machine. Conclusions: The matching of a FFF beam to a flattened beam at a depth of 10 cm in water by increasing the FFF beam energy does not reduce any of the reported benefits of FFF beams. Conversely, there are a number of potential benefits resulting from matching the FFF beam; the depth of maximum dose is deeper, the out of field dose is potentially reduced, and the beam quality and penetration more closely resembles the flattened beams currently used in clinical practice, making dose distributions in water more alike. Highlighted in this work is the fact that some conventional specifications and methods for measurement of beam parameters such as penumbra are not relevant and further work is required to address this situation with respect to “matched” FFF beams and to determine methods of measurement that are not reliant on an associated flattened beam.

43 PARTICLE ACCELERATORS↗

M.S.L.A.P. Modular Spectral Line Analysis Program documentation

MSLAP is a software for analyzing spectra, providing the basic structure to identify spectral features, to make quantitative measurements of this features, and to store the measurements for convenient access. MSLAP can be used to measure not only the zeroth moment (equivalent width) of a profile, but also the first and second moments. Optical depths and the corresponding column densities across the profile can be measured as well for sufficiently high resolution data. The software was developed for an interactive, graphical analysis where the computer carries most of the computational and data organizational burden and the investigator is responsible only for all judgement decisions. It employs sophisticated statistical techniques for determining the best polynomial fit to the continuum and for calculating the uncertainties.

Joseph, Charles L.↗

Suppression of donor-vacancy clusters in germanium by concurrent annealing and irradiation

Diffusion of phosphorous and arsenic in germanium under in situ proton irradiation has been performed and analyzed with secondary ion mass spectrometry. Dopant profiles corresponding to proton-exposed regions exhibit a higher penetration depth and more pronounced box shape than profiles of nonexposed regions. Continuum theoretical simulations reveal that diffusion under irradiation is much less affected by inactive donor-vacancy clusters than diffusion under annealing only. The suppression of donor-vacancy clusters is caused by interstitials in supersaturation and vacancy concentrations close to thermal equilibrium. Concurrent annealing and irradiation have the potential to attain high active doping levels in Ge.

36 MATERIALS SCIENCE↗

The remote sensing of ocean primary productivity - Use of a new data compilation to test satellite algorithms

Global pigment and primary productivity algorithms based on a new data compilation of over 12,000 stations occupied mostly in the Northern Hemisphere, from the late 1950s to 1988, were tested. The results showed high variability of the fraction of total pigment contributed by chlorophyll, which is required for subsequent predictions of primary productivity. Two models, which predict pigment concentration normalized to an attenuation length of euphotic depth, were checked against 2,800 vertical profiles of pigments. Phaeopigments consistently showed maxima at about one optical depth below the chlorophyll maxima. CZCS data coincident with the sea truth data were also checked. A regression of satellite-derived pigment vs ship-derived pigment had a coefficient of determination. The satellite underestimated the true pigment concentration in mesotrophic and oligotrophic waters and overestimated the pigment concentration in eutrophic waters. The error in the satellite estimate showed no trends with time between 1978 and 1986.

Balch, William↗

A procedure to determine the planar integral spot dose values of proton pencil beam spots

Purpose: Planar integral spot dose (PISD) of proton pencil beam spots (PPBSs) is a required input parameter for beam modeling in some treatment planning systems used in proton therapy clinics. The measurement of PISD by using commercially available large area ionization chambers, like the PTW Bragg peak chamber (BPC), can have large uncertainties due to the size limitation of these chambers. This paper reports the results of our study of a novel method to determine PISD values from the measured lateral dose profiles and peak dose of the PPBS. Methods: The PISDs of 72.5, 89.6, 146.9, 181.1, and 221.8 MeV energy PPBSs were determined by area integration of their planar dose distributions at different depths in water. The lateral relative dose profiles of the PPBSs at selected depths were measured by using small volume ion chambers and were investigated for their angular anisotropies using Kodak XV films. The peak spot dose along the beam's central axis (D{sub 0}) was determined by placing a small volume ion chamber at the center of a broad field created by the superposition of spots at different locations. This method allows eliminating positioning uncertainties and the detector size effect that could occur when measuring it in single PPBS. The PISD was then calculated by integrating the measured lateral relative dose profiles for two different upper limits of integration and then multiplying it with corresponding D{sub 0}. The first limit of integration was set to radius of the BPC, namely 4.08 cm, giving PISD{sub RBPC}. The second limit was set to a value of the radial distance where the profile dose falls below 0.1% of the peak giving the PISD{sub full}. The calculated values of PISD{sub RBPC} obtained from area integration method were compared with the BPC measured values. Long tail dose correction factors (LTDCFs) were determined from the ratio of PISD{sub full}/PISD{sub RBPC} at different depths for PPBSs of different energies. Results: The spot profiles were found to have angular anisotropy. This anisotropy in PPBS dose distribution could be accounted in a reasonable approximate manner by taking the average of PISD values obtained using the in-line and cross-line profiles. The PISD{sub RBPC} values fall within 3.5% of those measured by BPC. Due to inherent dosimetry challenges associated with PPBS dosimetry, which can lead to large experimental uncertainties, such an agreement is considered to be satisfactory for validation purposes. The PISD{sub full} values show differences ranging from 1 to 11% from BPC measured values, which are mainly due to the size limitation of the BPC to account for the dose in the long tail regions of the spots extending beyond its 4.08 cm radius. The dose in long tail regions occur both for high energy beams such as 221.8 MeV PPBS due to the contributions of nuclear interactions products in the medium, and for low energy PPBS because of their larger spot sizes. The calculated LTDCF values agree within 1% with those determined by the Monte Carlo (MC) simulations. Conclusions: The area integration method to compute the PISD from PPBS lateral dose profiles is found to be useful both to determine the correction factors for the values measured by the BPC and to validate the results from MC simulations.

43 PARTICLE ACCELERATORS↗

Creating Seasonal Climatologies of Aerosol Lidar Ratios Over Ocean Using MODIS AOD Constrained Retrievals and GOCART Model Simulations

The current CALIPSO algorithms assign one lidar ratio (i.e., extinction-to-backscatter ratio; LR) value globally for each of the seven tropospheric aerosol types. In a future data products release, the CALIPSO project aims to improve these algorithms through the development of regional and seasonal LR climatologies. In this work, aerosol LRs are inferred through CALIOP backscatter profiles constrained by collocated aerosol optical depth (AOD) from Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) data. This analysis is subsampled for those profiles that are cloud-free and contain only one CALIOP-classified aerosol type (e.g., marine). The CALIOP profiles are then collocated with aerosol volume fractions obtained through Goddard Chemistry Aerosol Radiation and Transport (GOCART) model simulations. In this poster, we show twelve-year (June 2006-August 2018) mean spatial distributions of inferred aerosol LRs for CALIOP-classified marine aerosols and how they correspond inversely with patterns of GOCART sea salt volume fraction (SSVF). Near land masses, smaller SSVFs and larger LRs are found (due to the influence of over-land aerosols). In the remote ocean regions (likely less impacted by over-land aerosols), larger SSVFs and smaller LRs are found. The developed relationship between the GOCART model SSVFs and MODIS AOD constrained LRs is used to create model-assisted seasonal LR maps. Additionally, we show maps of inferred LRs from constrained retrievals using the CALIPSO Ocean Derived Column Optical Depth (ODCOD) product and comparisons with those from the MODIS analyses. The technique demonstrated here benefits CALIPSO in the near-term, but similar methods can also be applied to the next generation space-based elastic backscatter lidars with collocated passive sensors, such as those of the upcoming NASA Atmosphere Observing System (AOS).

Travis Toth↗

Mapping Aerosol Lidar Ratios Over Ocean Using Constrained Retrievals and A Global Aerosol Model

The current NASA Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) algorithms assign one lidar ratio (i.e., extinction-to-backscatter ratio; LR) value globally for each of the seven tropospheric aerosol types. In a future data products release, the CALIPSO project aims to improve these algorithms through the development of regional and seasonal LR climatologies. In this work, aerosol LRs are inferred through Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) backscatter profiles constrained by collocated aerosol optical depth (AOD) from Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) data. This analysis is subsampled for those profiles that are cloud-free and contain only one CALIOP-classified aerosol type (e.g., marine). The CALIOP profiles are then collocated with aerosol volume fractions obtained through Goddard Chemistry Aerosol Radiation and Transport (GOCART) model simulations. In this presentation, we show that the twelve-year (June 2006-August 2018) mean spatial distributions of inferred aerosol LRs for CALIOP-classified marine aerosols correspond inversely with patterns of GOCART sea salt volume fraction (SSVF). For example, smaller SSVFs (< 65%) and larger LRs (> 55 sr), are found near land masses. This is indicative of the influence of over-land aerosols (e.g., pollution and biomass burning smoke). In the remote oceans (i.e., regions likely less impacted by non-sea salt aerosols), larger SSVFs (> 95%) and smaller LRs (< 25 sr) are found. The developed relationship between the GOCART SSVFs and MODIS AOD constrained LRs (polynomial fit intersect values of ~56 sr for SSVF of 0% and ~21 sr for SSVF of 100%) is used to produce model-assisted climatological LR maps on seasonal scales. Additionally, we show maps of inferred LRs from constrained retrievals using the CALIPSO Ocean Derived Column Optical Depth (ODCOD) product and comparisons with those from the MODIS analyses. The technique demonstrated in this study not only benefits CALIPSO in the near-term, but similar methods can be applied to future spaceborne elastic backscatter lidars with collocated passive sensors, such as those associated with the upcoming NASA Atmosphere Observing System (AOS).

Travis Toth↗

The “accumulation effect” of positrons in the stack of foils, detected by measurements of the positron implantation profile

The profiles of positrons implanted from the radioactive source {sup 22}Na into a stack of foils and plates are the subject of our experimental and theoretical studies. The measurements were performed using the depth scanning of positron implantation profile method, and the theoretical calculations using the phenomenological multi-scattering model (MSM). Several stacks consisting of silver, gold and aluminum foils, and titanium and germanium plates were investigated. We notice that the MSM describes well the experimental profiles; however when the stack consisting of silver and gold foils, the backscattering and linear absorption coefficients differ significantly from those reported in the literature. We suggest the energy dependency of the backscattering coefficient for silver and gold. In the stacks which comprise titanium and germanium plates, there were observed the features, which indicate the presence of the “accumulation effect” in the experimental implantation profile. This effect was previously detected in implantation profiles in Monte Carlo simulations using the GEANT4 tool kit, and it consists in higher localization of positrons close the interface. We suppose that this effect can be essential for positron annihilation in any heterogeneous materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SOLAR MODELS WITH NEW LOW METAL ABUNDANCES

In the past decade, the photospheric abundances of the Sun had been revised several times by many observers. The standard solar models constructed with the new low-metal abundances disagree with helioseismic results and detected neutrino fluxes. The solar model problem has puzzled some stellar physicists for more than 10 years. Rotation, enhanced diffusion, convection overshoot, and magnetic fields are used to reconcile the new abundances with helioseismology. The too low helium subsurface abundance in enhanced diffusion models can be improved by the mixing caused by rotation and magnetic fields. The problem of the depth of the convective zone in rotating models can be resolved by convection overshoot. Consequently, the Asplund–Grevesse–Sauval rotation model including overshooting (AGSR) reproduces the seismically inferred sound-speed and density profiles and the convection zone depth as well as the Grevesse and Sauval model computed before. But this model fails to reproduce the surface helium abundance, which is 0.2393 (2.6 σ away from the seismic value), and neutrino fluxes. The magnetic model called AGSM keeps the agreement of the AGSR and improves the prediction of the surface helium abundance. The observed separation ratios r {sub 02} and r {sub 13} are reasonably reproduced by AGSM. Moreover, neutrino fluxes calculated by this model are not far from the detected neutrino fluxes and the predictions of previous works.

79 ASTRONOMY AND ASTROPHYSICS↗

Mapping Aerosol Lidar Ratios Over Ocean for CALIPSO Using Modis AOD-Constrained Retrievals and A Global Aerosol Model

The CALIPSO aerosol algorithms currently assign one lidar ratio value for each of the seven tropospheric aerosol types. In a future data products release, the CALIPSO project aims to improve these algorithms by developing regional and seasonal lidar ratio climatologies. In this study, aerosol lidar ratios are inferred through Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) backscatter profiles constrained by collocated aerosol optical depth from Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) datasets. The analysis is subsampled for only those profiles that are cloud-free and contain one aerosol type (based on CALIOP feature classification). In addition, the CALIOP profiles are collocated with aerosol volume fractions simulated by the Goddard Chemistry Aerosol Radiation and Transport (GOCART) model. In this talk, the twelve-year (2006-2017) mean spatial distributions of inferred aerosol lidar ratios for CALIOP-classified marine aerosols and the corresponding modeled sea salt volume fractions (SSVF) will be shown. Model-assisted climatological lidar ratio maps on a seasonal scale will also be presented, developed from the empirical relationship found between the modeled SSVF and lidar ratios. A comparison with past studies will be provided as well as results of a sensitivity study regarding the variability of retrieved lidar ratios as a function of horizontal averaging resolution. While the majority of this talk will focus on lidar ratios for CALIOP-classified marine aerosols, preliminary results will be shown for other aerosol types over ocean, such as dust and elevated smoke.

Travis Toth↗

Airborne Lidar Measurements of Ozone and Aerosol Profiles Over Major US Metropolitan Areas

During field missions in 2021 and 2023, the airborne NASA Langley Research Center High Spectral Resolution Lidar 2 (HSRL 2) measured the temporal and spatial evolution of ozone and aerosol distributions impacting urban air quality over the four most populated cities in the United States. HSRL-2 measurements in 2021 were acquired over the Houston metropolitan region, including Galveston Bay and the Houston Ship Channel, as part of the NASA Tracking Aerosol Convection Experiment – Air Quality (TRACER-AQ) mission conducted in collaboration with the Department of Energy. HSRL-2 measurements were acquired over Los Angeles, Chicago, and New York City in 2023 as part of the NASA Synergistic TEMPO Air Quality Science (STAQS) mission conducted in collaboration with the NOAA Atmospheric Emissions and Reactions Observed from Megacities to Marine Areas (AEROMMA) mission. HSRL 2 provided nadir vertical profiles of ozone, aerosol backscatter, extinction, and depolarization as the aircraft flew lawnmower type patterns at 9 km for several hours over these urban areas. HSRL-2 measured profiles of aerosol extinction and aerosol optical depth (AOD) via the HSRL technique at 355 and 532 nm and profiles of aerosol backscatter and depolarization at 355, 532, and 1064 nm. Mixed Layer Heights (MLH) were derived by locating sharp vertical gradients in the profiles of aerosol backscatter. The flights were comprised of up to three repeating lawnmower patterns over each city showing the evolution of the ozone and aerosol distributions from the morning through the afternoon. The HSRL-2 measurements reveal ozone enhancements near the surface as well as in the free troposphere above the mixed layer. Some lidar measurements over Chicago and New York City show the daytime boundary layer growing into elevated layers of biomass burning aerosol. These layers complicate efforts to use column-integrated satellite measurements to infer surface air quality. As expected, mixed layer height (MLH) typically increased significantly during the day; however, during some flights, particularly over the Houston area, MLH also showed large spatial variability associated with changes in surface cover and/or small scale circulations. Often HSRL-2 measurements of AOD also showed large spatial and temporal variability throughout the day over these cities. We discuss how the ozone and aerosol profiles are averaged over different vertical and horizontal scales near the surface for use in assessments of regional air quality models and near-surface ozone retrievals from NASA’s recently launched Tropospheric Emissions: Monitoring Pollution (TEMPO) satellite.

Lidar↗

HSRL-2 Observations over the Houston, TX Region during TRACER-AQ

During field missions in 2021 and 2023, the airborne NASA Langley Research Center High Spectral Resolution Lidar 2 (HSRL 2) measured the temporal and spatial evolution of ozone and aerosol distributions impacting urban air quality over the four most populated cities in the United States. HSRL-2 measurements in 2021 were acquired over the Houston metropolitan region, including Galveston Bay and the Houston Ship Channel, as part of the NASA Tracking Aerosol Convection Experiment – Air Quality (TRACER-AQ) mission conducted in collaboration with the Department of Energy. HSRL-2 measurements were acquired over Los Angeles, Chicago, and New York City in 2023 as part of the NASA Synergistic TEMPO Air Quality Science (STAQS) mission conducted in collaboration with the NOAA Atmospheric Emissions and Reactions Observed from Megacities to Marine Areas (AEROMMA) mission. HSRL 2 provided nadir vertical profiles of ozone, aerosol backscatter, extinction, and depolarization as the aircraft flew lawnmower type patterns at 9 km for several hours over these urban areas. HSRL-2 measured profiles of aerosol extinction and aerosol optical depth (AOD) via the HSRL technique at 355 and 532 nm and profiles of aerosol backscatter and depolarization at 355, 532, and 1064 nm. Mixed Layer Heights (MLH) were derived by locating sharp vertical gradients in the profiles of aerosol backscatter. The flights were comprised of up to three repeating lawnmower patterns over each city showing the evolution of the ozone and aerosol distributions from the morning through the afternoon. The HSRL-2 measurements reveal ozone enhancements near the surface as well as in the free troposphere above the mixed layer. Some lidar measurements over Chicago and New York City show the daytime boundary layer growing into elevated layers of biomass burning aerosol. These layers complicate efforts to use column-integrated satellite measurements to infer surface air quality. As expected, mixed layer height (MLH) typically increased significantly during the day; however, during some flights, particularly over the Houston area, MLH also showed large spatial variability associated with changes in surface cover and/or small scale circulations. Often HSRL-2 measurements of AOD also showed large spatial and temporal variability throughout the day over these cities. We discuss how the ozone and aerosol profiles are averaged over different vertical and horizontal scales near the surface for use in assessments of regional air quality models and near-surface ozone retrievals from NASA’s recently launched Tropospheric Emissions: Monitoring Pollution (TEMPO) satellite.

Lidar↗

Characterizing Intracluster Light in the Hubble Frontier Fields

We investigate the intracluster light (ICL) in the six Hubble Frontier Field clusters at 0.3<z<0.6. We employ a new method, which is free from any functional form of the ICL profile, and exploit the unprecedented depth of this Hubble Space Telescope imaging to map the ICL’s diffuse light out to clustrocentric radii R∼300 kpc (μ{sub ICL}∼27 mag arcsec{sup −2}). From these maps, we construct radial color and stellar mass profiles via SED fitting and find clear negative color gradients in all systems with increasing distance from the Brightest Cluster Galaxy (BCG). While this implies older/more metal-rich stellar components in the inner part of the ICL, we find that the ICL mostly consists of a ≲2 Gyr population, and plausibly originated with logM{sub ∗}/M{sub ⊙}≲10 cluster galaxies. Furthermore, we find that 10%–15% of the ICL’s mass at large radii (≳150 kpc) lies in a younger/bluer stellar population (∼1 Gyr), a phenomenon not seen in local samples. We attribute this light to the higher fraction of star-forming/(post-)starburst galaxies in clusters at z∼0.5. Ultimately, we find the ICL’s total mass to be logM{sub ∗}{sup ICL}/M{sub ⊙}∼11–12, constituting 5%–20% of the clusters’ total stellar mass, or about half of the value at z∼0. The above implies distinct formation histories for the ICL and BCGs/other massive cluster galaxies; i.e., the ICL at this epoch is still being constructed rapidly (∼40 M{sub ⊙} yr{sup −1}), while the BCGs have mostly completed their evolution. To be consistent with the ICL measurements of local massive clusters, such as Virgo, our data suggest mass acquisition mainly from quiescent cluster galaxies is the principal source of ICL material in the subsequent ∼5 Gyr of cosmic time.

79 ASTRONOMY AND ASTROPHYSICS↗

SU-E-T-561: Development of Depth Dose Measurement Technique Using the Multilayer Ionization Chamber for Spot Scanning Method

Purpose: To develop a measurement technique which suppresses the difference between profiles obtained with a multilayer ionization chamber (MLIC) and with a water phantom. Methods: The developed technique multiplies the raw MLIC data by a correction factor that depends on the initial beam range and water equivalent depth. The correction factor is derived based on a Bragg curve calculation formula considering range straggling and fluence loss caused by nuclear reactions. Furthermore, the correction factor is adjusted based on several integrated depth doses measured with a water phantom and the MLIC. The measured depth dose profiles along the central axis of the proton field with a nominal field size of 10 by 10 cm were compared between the MLIC using the new technique and the water phantom. The spread out Bragg peak was 20 cm for fields with a range of 30.6 cm and 6.9 cm. Raw MLIC data were obtained with each energy layer, and integrated after multiplying by the correction factor. The measurements were performed by a spot scanning nozzle at Nagoya Proton Therapy Center, Japan. Results: The profile measured with the MLIC using the new technique is consistent with that of the water phantom. Moreover, 97% of the points passed the 1% dose /1mm distance agreement criterion of the gamma index. Conclusion: We have demonstrated that the new technique suppresses the difference between profiles obtained with the MLIC and with the water phantom. It was concluded that this technique is useful for depth dose measurement in proton spot scanning method.

07 ISOTOPE AND RADIATION SOURCES↗