Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

The Effect of η Phase Precipitates on the Creep Behavior of Alloy 263 and Variants

Phase stability is an important design parameter for Ni-based superalloys to be used in future advanced ultra-supercritical (AUSC) power plants as exposure times in this type of environment are considerable. In this investigation, microstructures based on candidate alloy 263 were obtained with varying amounts of η precipitates using isothermal exposure at 800°C for times ranging from 1,000 h to 10,000 h. The effect of η phase stability on the creep properties was determined using creep specimens isothermally aged at 800°C for 8 h, 3,000 h, 5,000 h and 10,000 h prior to creep screening. The creep life was found to exponentially decrease with increasing density of η phase while the elongation to failure was found to increase. Furthermore, the minimum creep rate was related to the density of η phase; a relationship that did not depend on the alloy formulation. Modification to the Ti and Al concentrations slowed down the γ' to η transformation while doubling the γ' fraction after standard heat treatment. By modifying the Ti and Al content, and thereby improving γ' stability over η, the creep lives of specimens isothermally aged for up to 5,000 h were greater than that of the nominal alloy in its standard aged condition.

36 MATERIALS SCIENCE↗

The importance of ester cleavage in the butylamine pretreatment of hybrid poplar

Butylamine is an effective in-and-out pretreatment solvent for hybrid poplar. It penetrates the cell walls and breaks ester cross-linkages, facilitating lignin release and improving enzymatic digestion. This work explores the “in-and-out” pretreatment of hybrid poplar with butylamine as a distillable protic solvent and reagent. The butylamine solvent can be removed by vacuum distillation with >95% solvent removal in all cases, providing a valuable scheme for efficient solvent recovery and recycling. Running the reaction with neat butylamine at 140 °C for 3 hours results in high yields of monosaccharides (90% glucose and 71% xylose) after enzymatic digestion, and a good tolerance to water content with no significant reduction in glucose yield up to an 8 : 1 water : butylamine ratio. We investigate the mechanisms of this pretreatment using powder X-ray diffraction, thermogravimetric analysis, fluorescence microscopy, elemental analysis, solid state and solution state nuclear magnetic spectroscopy to observe chemical and material markers of the pretreatment chemistry. The results suggest that the butylamine leaves the macro and microstructural properties of the lignocellulose relatively unaltered, but conducts targeted ester cleavage chemistry to remove cross-links between the various biopolymers and partially solubilize the lignin component of the biomass. These findings should act to guide future development of pretreatment chemistry for the development of biorefinery processes, and assist in the utilization of biomass as a starting point for chemical syntheses.

Palasz, Joseph M↗

Thermal conductivity in Bi 0.5 Sb 1.5 Te 3+ x and the role of dense dislocation arrays at grain boundaries

Several prominent mechanisms for reduction in thermal conductivity have been shown in recent years to improve the figure of merit for thermoelectric materials. Such a mechanism is a hierarchical all-length-scale architecturing that recognizes the role of all microstructure elements, from atomic to nano to microscales, in reducing (lattice) thermal conductivity. In this context, there have been recent claims of remarkably low (lattice) thermal conductivity in Bi 0.5 Sb 1.5 Te 3 that are attributed to seemingly ordinary grain boundary dislocation networks. These high densities of dislocation networks in Bi 0.5 Sb 1.5 Te 3 were generated via unconventional materials processing with excess Te (which formed liquid phase, thereby facilitating sintering), followed by spark plasma sintering under pressure to squeeze out the liquid. We reproduced a practically identical microstructure, following practically identical processing strategies, but with noticeably different (higher) thermal conductivity than that claimed before. We show that the resultant microstructure is anisotropic, with notable difference of thermal and charge transport properties across and along two orthonormal directions, analogous to anisotropic crystals. Thus, we believe that grain boundary dislocation networks are not the primary cause of enhanced ZT through reduction in thermal conductivity. Instead, we can reproduce the purported high ZT through a favorable but impractical and incorrect combination of thermal conductivity measured along the pressing direction of anisotropy while charge transport measured in the direction perpendicular to the anisotropic direction. We believe that our work underscores the need for consistency in charge and thermal transport measurements for unified and verifiable measurements of thermoelectric (and related) properties and phenomena.

36 MATERIALS SCIENCE↗

Shape memory properties and microstructural evolution of rapidly solidified CuAlBe alloys

In this work, the effects of Be addition on the microstructure and phase transformation temperatures of Cu–12Al–xBe (x = 0.4, 0.5 and 0.6 wt.%) shape memory alloys fabricated by using the arc-melting and melt-spinning techniques have been investigated. X-ray diffraction analysis revealed that the arc-melted alloys consisted of austenitic β{sub 1}, martensitic β{sub 1}′ and γ{sub 2} precipitate phases, whereas melt-spun ribbons were composed of a fully martensitic phase. The average grain size of martensitic phases in melt-spun ribbons was determined by electron microscopy images, showing a decrease with increasing Beryllium (Be) amount. Moreover, it was found that the Be addition in the arc-melted alloys had a distinct effect on the morphology of the γ{sub 2} precipitate phase. Transmission electron microscopy analysis showed that the thickness of martensitic plates in the melt-spun ribbons reduced with increasing Be addition. In a differential scanning calorimeter analysis, no martensitic transformation (M{sub s}) peak was observed in arc-melted alloys, but it was clearly detected in melt-spun ribbons, in which M{sub s} decreased dramatically with increasing Be addition. The improvement in the shape memory ability of melt-spun ribbons was explained in terms of the refinement in grain size and martensitic plates. - Highlights: • The CuAlBe SMAs were produced by means of arc-melter and melt-spinner techniques. • MT was directly obtained in melt-spuns without any intermediate process. • The transformation temperatures decreased with increasing Be amount. • The thickness of martensitic plates in the ribbons reduced with increasing Be. • SMP of CuAl was improved by the addition of Be together with rapid solidification.

36 MATERIALS SCIENCE↗

Laser Additive Manufacturing of F/M Steels for Radiation Tolerant Nuclear Components

According to the Nuclear Energy R&D Roadmap Report submitted to Congress in 2010, one the key challenges facing the nuclear energy industry involves development of new reactor designs with reduced capital costs. Two related R&D objectives outlined in the report include: 1) Making improvements in the affordability of new reactors; and 2) Development of structural materials to withstand irradiation for longer periods. Laser additive manufacturing (LAM) is particularly well suited for more rapid and economical fabrication of reactor components relative to current fabrication methods. The proposed work involving LAM directly addresses the two R&D objectives outlined above relevant to the pertinent mission problems. The classical Materials Science approach involving development of Process/Structure/Property/Performance (P/S/P/P) relations was employed in this project. Processing included LAM and heat-treating. Thermal cycling during LAM is discussed here, and phase diagrams and continuous cooling transformation (CCT) diagrams are used to rationalize microstructural evolution. Structures were characterized including grain size & morphology, volume fraction, morphology, composition and location of carbides in as-deposited and heat-treated conditions. In the simplest sense, the goal was to control microstructures through process manipulation with a view toward optimizing properties and performance in service.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Study on the Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Ca Alloy Wire for Biomaterial Application

Due to their excellent biocompatibility and biodegradability, magnesium alloy wires have attracted much attention for biomaterial applications including orthopedic K-wires and sutures in wound closure. In this study, Mg-3Zn-0.2Ca alloy wires were prepared by cold drawing combined with proper intermediate annealing process. Microstructures, texture, mechanical properties and corrosion behavior of Mg-3Zn-0.2Ca alloy wire in a simulated body fluid were investigated. The results showed that the secondary phase and average grain size of the Mg-3Zn-0.2Ca alloy were refined in comparison with the as-extruded alloy and a strong (0002)<10-10>//DD basal fiber texture system was formed after multi-pass cold drawing. After the annealing, most of the basal planes were tilted to the drawing direction (DD) by about 35°, presenting the characteristics of random texture, and the texture intensity decreased. The as-annealed wire shows good mechanical properties with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 253 ± 8.5 MPa, 212 ± 11.3 MPa and 9.2 ± 0.9%, respectively. Electrochemical and hydrogen evolution measurements showed that the corrosion resistance of the Mg-3Zn-0.2Ca alloy wire was improved after the annealing. The immersion test indicated that the Mg-3Zn-0.2Ca wire exhibited uniform corrosion behavior during the initial period of immersion, but then exhibited local corrosion behavior.

36 MATERIALS SCIENCE↗

Steam explosion pretreatment coupling high-temperature short-time sterilization facilitating cellulose degradation and sporulation-regulatory gene expression in high-solid fermentation

Steam explosion coupling high-temperature short-time sterilization (SE-HTST) was exploited to modify cellulosic biomass medium properties and promote high-solid fermentation (HSF). Biomass characterization analysis showed that SE-HTST enlarged microstructural pores and cavities in solid media, providing more effective space for microbial growth. Meanwhile, SE-HTST helped to release glucose from the cellulose with 35.8 ± 4.5, 20.0 ± 2.3, and 12.3 ± 5.7 mg glucose/g dry medium at 24, 48, and 72 h of fermentation, which were 3.1, 2.3, and 1.5 times higher than that in medium from conventional thermal sterilization (CTS), respectively. SE-HTST increased the viable cell and spore number of Bacillus subtilis by 1.8 and 1.6 times at 72 h of fermentation compared to CTS. Moreover, the expressions of master transcriptional gene spo0A and the early sigma factors of sigF and sigE genes gradually increased in the SE-HTST medium, showing enhanced sporulation in HSF. Therefore, SE-HTST is an effective strategy for facilitating cellulose degradation, improving glucose nutrients in biomass medium, and promoting sporulation-regulatory gene expression during high-solid fermentation, which enhances the production of microbial ecological agents using B. subtilis significantly.

59 BASIC BIOLOGICAL SCIENCES↗

Estimating Alpine Snow Depth by Combining Multi-Frequency Passive Radiance Observations with Ensemble Snowpack Modeling

This paper presents a physically-based snow depth retrieval algorithm adapted for deep mountainous snowpack and airborne multifrequency (10.7, 18.7, 37.0 and 89.0 GHz) passive microwave (PM) radiance observations from a single flight. The algorithm employs a single forecast-analysis cycle of a traditional sequential assimilation scheme. It uses an ensemble of multi-layer snowpack model runs to resolve snow microstructure and melt-refreeze crusts, andmicrowave radiative transfer models to relate snow properties to microwave measurements.Snow depth was retrieved at a 120 m spatial resolution over three 1 km2 Intensive Study Area (ISA) within the Rabbit Ears Meso-Cell Study Area (MSA) from the NASA Cold Land Processes Experiment (CLPX) in Colorado (United States) for one date in February 2003. When evaluated against in situ observations, root mean square error (RMSE) of the snow depth from the assimilation was 13.3 cm for areas with low (<5 %) forest cover, which was a reduction of 48 % in the RMSE compared with the modeled snow depth when the PM observations were not assimilated; indicating a ~5% relative error of the posterior snow depth with respect to the average snow depth (200 cm) measured at these pixels. For pixels with forest cover ranging from 5-15% and 15-30%, results were improved (R2 increased from 0.65 to 0.71 and from 0 to 0.38, respectively) by introducing a forest radiative transfer model during the assimilation.

Airborne Multifrequency↗

Understanding the local structure of disordered carbons from cellulose and lignin

An electron microscopy investigation was performed to understand the relationship between the microstructure and properties of carbonized cellulose and lignin (softwood kraft lignin) relative to the structure of the original biomass components. Structure details at micro- and molecular levels were investigated by scanning transmission electron microscopy. Atomic-resolution images revealed the presence of random disordered carbon in carbonized cellulose (C-CNC) and of large domains of well-ordered carbon with graphite sheet structure in carbonized lignin (C-Lignin). These structural differences explain why C-CNC exhibits higher surface area and porosity than C-Lignin. The presence of certain well-ordered carbon in carbonized lignin indicates some of the carbon in lignin are graphitized with heat treatment temperature up to 950 °C. This result is encouraging for future endeavors of attaining acceptable modulus of carbon fiber from lignin given suitable modifications to the chemistry and structure of lignin. The results of this research contribute to an improved understanding of the carbonization mechanism of the key cellulose and lignin components of biomass materials.

54 ENVIRONMENTAL SCIENCES↗

Strongly nonlinear wave propagation in elasto-plastic metamaterials: Low-order dynamic modeling

Nonlinear elastic metamaterials are known to support a variety of dynamic phenomena that enhance our capacity to manipulate elastic waves. Since these properties stem from complex, subwavelength geometry, full-scale dynamic simulations are often prohibitively expensive at scales of interest. Prior studies have therefore utilized low-order effective medium models, such as discrete mass-spring lattices, to capture essential properties in the long-wavelength limit. While models of this type have been successfully implemented for a wide variety of nonlinear elastic systems, they have predominantly considered dynamics depending only on the instantaneous kinematics of the lattice, neglecting history-dependent effects, such as wear and plasticity. Here, to address this limitation, the present study develops a lattice-based modeling framework for nonlinear elastic metamaterials undergoing plastic deformation. Due to the history- and rate-dependent nature of plasticity, the framework generally yields a system of differential-algebraic equations whose computational cost is significantly greater than an elastic system of comparable size. We demonstrate the method using several models inspired by classical lattice dynamics and continuum plasticity theory and explore means to obtain empirical plasticity models for general geometries, thereby gaining insight into the influence of microstructural plasticity on effective material performance, which can be used to improve the design of nonlinear mechanical metamaterials.

Dynamic simulation↗

Defect-specific strength factors and superposition model for predicting strengthening of ion irradiated Fe18Cr alloy

Here, a high-purity binary alloy Fe18Cr was subjected to heavy-ion irradiation in order to provide improved understanding of the irradiation effect on radiation hardening associated with dislocation loop and network formation, α’ precipitation. The specimens were irradiated with 8 MeV Fe ions (~2 μm ion range) to midrange doses of 0.37 and 3.7 dpa at 300, 350 and 450 °C using dose rates of ~10 –5 –10 –3 dpa/s. Nanoindentation testing was performed to extract the bulk equivalent hardness at low depth from these ion irradiated specimens. High-quality transmission electron microscopy (TEM) images were acquired by utilizing a flash electropolishing method on the Focused Ion Beam (FIB) prepared liftouts. An accurate calculation of the strength factor was provided based on detailed TEM characterization of the irradiated microstructures. A newly refined hardening superposition method was applied to combine the strengthening components from each microstructure. The good agreement between microstructure predicted strength and measured strength further demonstrated the fidelity to use hardening model to quantify the mechanical properties of ion irradiated materials.

36 MATERIALS SCIENCE↗

Computational design of microarchitected porous electrodes for redox flow batteries

Porous electrodes are used as the core reactive component across electrochemical technologies. In flowing systems, controlling the fluid distribution, species transport, and reactive environment is critical to attaining high performance. However, conventional electrode materials like felts and papers provide few opportunities for precise engineering of the electrode and its microstructure. To address these limitations, architected electrodes composed of unit cells with spatially varying geometry determined via computational optimization are proposed. Resolved simulation is employed to develop a homogenized description of the constituent unit cells. These effective properties serve as inputs to a continuum model for the electrode when used in the negative half-cell of a vanadium redox flow battery. Porosity distributions minimizing power loss are then determined via computational design optimization to generate architected porosity electrodes. The architected electrodes are compared to bulk, uniform porosity electrodes and found to lead to increased power efficiency across operating flow rates and currents. The design methodology is further used to generate a scaled-up electrode with comparable power efficiency to the bench-scale systems. Finally, the variable porosity architecture and computational design methodology presented here thus offers a novel pathway for automatically generating spatially engineered electrode structures with improved power performance.

25 ENERGY STORAGE↗

Asphaltene-induced spontaneous emulsification: Effects of interfacial co-adsorption and viscoelasticity

Asphaltenes are a class of high molecular weight aromatic compounds found in crude oil. They adsorb onto toluene-water interfaces and induce a spontaneous emulsification phenomenon, whereby stable water-in-oil emulsions form without the need of an external energy input. This work aims to control and understand the factors affecting spontaneous droplet formation in the presence of asphaltene adsorption. This is particularly useful for crude oil refining, where the presence of a stable emulsion hampers the efficiency of downstream processing operations. We explore the effect of the addition of copolymers designed as crude oil flow improvers as a means to control the extent of emulsion formation. We find that the polymers competitively adsorb onto the toluene-water interface and diminish spontaneous emulsification. Additionally, we conduct fluorescence microscopy experiments and measurements of the interfacial energy to determine the mechanism of spontaneous emulsification in asphaltene systems. We conclude that an emulsion forms via the diffusion of molecular water into the oil phase and subsequent binding with asphaltene aggregates, leading to the nucleation of micrometer-sized water droplets. We find that the polymer forms complexes with the dissolved asphaltenes, possibly hampering the ability of diffused water to bind to the asphaltenes and reducing the extent of spontaneous emulsification. Finally, we investigate the role of interfacial shear and dilatational viscoelasticity to better understand which fundamental interfacial properties are important in the emulsification of asphaltene-laden systems. We find that the rate of formation of an interfacial microstructural network is inversely correlated with the extent and rate of spontaneous emulsification.

42 ENGINEERING↗

Fundamental Investigations of Mechanical and Chemical Degradation Mechanisms in Lithium Ion Battery Materials (Final Technical Report)

The objective of our effort under the DOE EPSCoR Implementation grant is to establish a comprehensive and internationally recognized research program at Brown University and University of Rhode Island in understanding degradation mechanisms and to improve the cycle and calendar life of lithium ion battery (LIB) materials. A series of basic investigations are undertaken to characterize the mechanical and chemical degradation mechanisms, which can help enable new higher capacity and longer lasting electrode designs. Controlling mechanical and chemical degradation is the primary challenge in developing the next generation of higher energy density batteries. The development of failure resistant battery microstructures will require a fundamental understanding of the evolution of stress, deformation, damage, and electrochemistry in battery materials during cyclic charging and discharging. In addition, controlling the reactions at the electrode/electrolyte interface is critical for the formation of a stable SEI layer. We address these issues through a combination of controlled experiments on model battery materials and practical composite electrodes, together with multi-scale computations. Our effort is organized into three focus areas that encompass many critical challenges in Lithium Ion Battery Technologies: (i) Mechanical properties, fracture and damage in electrode materials; (ii) Chemistry and Mechanics of Solid Electrolyte Interphase (SEI); (iii) Mechanical and Chemical Integrity of Solid-Solid Interfaces in Practical Electrodes.

25 ENERGY STORAGE↗

A review of the metastable omega phase in beta titanium alloys: the phase transformation mechanisms and its effect on mechanical properties

Since its discovery in 1954, the omega (ω) phase in titanium and its alloys has attracted substantial attention from researchers. The β-to-ω and ω-to-α phase transformations are central to β-titanium alloy design, but the transformation mechanisms have been a subject of debate. With new generations of aberration-corrected transmission electron microscopy and atom probe tomography, both the spatial resolution and compositional sensitivity of phase transformation analysis have been rapidly improving. Furthermore, this review provides a detailed assessment of the new understanding gained and related debates in this field enabled by advanced characterization methods. Specifically, new insights into the possibility of a coupled diffusional-displacive component in the β-to-ω transformation and key nucleation driving forces for the ω-assisted α phase formation are discussed. Additionally, the influence of ω phase on the mechanical properties of β-titanium alloys is also reviewed. Lastly, a perspective on open questions and future direction for research is discussed.

36 MATERIALS SCIENCE↗

Bio-inspired multiscale design for perovskite solar cells

Metal halide perovskite semiconductors have attractive light-harvesting and charge-carrier transport properties for photovoltaics. Perovskite solar cells (PSCs) and modules have demonstrated their commercial promise with high power conversion efficiencies, but still face stability challenges. In this Review, we explore how biomaterials offer design inspiration for the development of durable and efficient PSCs at three different scales. At the molecular level, bio-inspired molecular interactions are harnessed towards crystallization control and degradation prevention, which offers an enhancement in long-term maximum-power-point tracking stability. At the microstructural level, self-healing and strength-enhancing strategies, utilizing dynamic bonds and interfacial reinforcement, can help PSCs to recover from physical damage and maintain high performance. At the device level, macroscopic functionalities, such as moth-eye-inspired structures tailored to different layers, can collectively enable antireflection, radiative cooling and self-cleaning to optimize light management, heat dissipation and encapsulation in PSCs. Bio-inspired PSC research can combine improved efficiency and lifetime, with abundant, biocompatible alternatives to conventional stabilizers. Future efforts should focus on screening bioinspired molecules to optimize film crystallization and stability, developing self-healing mechanisms triggered by operational stress, designing cost-efficient biomicrostructures, and integrating multifunctional encapsulation to enhance the efficiency and lifespan of PSCs.

Duan, Tianwei↗

Dislocation dynamics simulations of plasticity at small scales

As metallic structures and devices are being created on a dimension comparable to the length scales of the underlying dislocation microstructures, the mechanical properties of them change drastically. Since such small structures are increasingly common in modern technologies, there is an emergent need to understand the critical roles of elasticity, plasticity, and fracture in small structures. Dislocation dynamics (DD) simulations, in which the dislocations are the simulated entities, offer a way to extend length scales beyond those of atomistic simulations and the results from DD simulations can be directly compared with the micromechanical tests. The primary objective of this research is to use 3-D DD simulations to study the plastic deformation of nano- and micro-scale materials and understand the correlation between dislocation motion, interactions and the mechanical response. Specifically, to identify what critical events (i.e., dislocation multiplication, cross-slip, storage, nucleation, junction and dipole formation, pinning etc.) determine the deformation response and how these change from bulk behavior as the system decreases in size and correlate and improve our current knowledge of bulk plasticity with the knowledge gained from the direct observations of small-scale plasticity. Our simulation results on single crystal micropillars and polycrystalline thin films can march the experiment results well and capture the essential features in small-scale plasticity. Furthermore, several simple and accurate models have been developed following our simulation results and can reasonably predict the plastic behavior of small scale materials.

36 MATERIALS SCIENCE↗

NiAl alloys for structural uses

Alloys based on the intermetallic compound NiAl are of technological interest as high temperature structural alloys. These alloys possess a relatively low density, high melting temperature, good thermal conductivity, and (usually) good oxidation resistance. However, NiAl and NiAl-base alloys suffer from poor fracture resistance at low temperatures as well as inadequate creep strength at elevated temperatures. This research program explored macroalloying additions to NiAl-base alloys in order to identify possible alloying and processing routes which promote both low temperature fracture toughness and high temperature strength. Initial results from the study examined the additions of Fe, Co, and Hf on the microstructure, deformation, and fracture resistance of NiAl-based alloys. Of significance were the observations that the presence of the gamma-prime phase, based on Ni3Al, could enhance the fracture resistance if the gamma-prime were present as a continuous grain boundary film or 'necklace'; and the Ni-35Al-20Fe alloy was ductile in ribbon form despite a microstructure consisting solely of the B2 beta phase based on NiAl. The ductility inherent in the Ni-35Al-20Fe alloy was explored further in subsequent studies. Those results confirm the presence of ductility in the Ni-35Al-20Fe alloy after rapid cooling from 750 - 1000 C. However exposure at 550 C caused embrittlement; this was associated with an age-hardening reaction caused by the formation of Fe-rich precipitates. In contrast, to the Ni-35Al-20Fe alloy, exploratory research indicated that compositions in the range of Ni-35Al-12Fe retain the ordered B2 structure of NiAl, are ductile, and do not age-harden or embrittle after thermal exposure. Thus, our recent efforts have focused on the behavior of the Ni-35Al-12Fe alloy. A second parallel effort initiated in this program was to use an alternate processing technique, mechanical alloying, to improve the properties of NiAl-alloys. Mechanical alloying in the conventional sense requires ductile powder particles which, through a cold welding and fracture process, can be dispersion strengthened by submicron-sized oxide particles. Using both the Ni-35Al-Fe alloys to contain approx. 1 v/o Y2O3. Preliminary results indicate that mechanically alloyed and extruded NiAl-Fe + Y2O3 alloys when heat treated to a grain-coarsened condition, exhibit improved creep resistance at 1000 C when compared to NiAl; oxidation resistance comparable to NiAl; and fracture toughness values a factor of three better than NiAl. As a result of the research initiated on this NASA program, a subsequent project with support from Inco Alloys International is underway.

Koss, D. A.↗