Search NASA⌕ Search

SEARCH · Search NASA

Results for “prototypes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Experimental Study of Beam Dynamics in the PIP-II MEBT Prototype

The Proton Improvement Plan, Stage Two (PIP-II) [1] is a program of upgrades proposed for the Fermilab injection complex, which central part is an 800 MeV, 2 mA CW SRF linac. A prototype of the PIP-II linac front end called PIP-II Injector Test (PIP2IT) is being built at Fermilab. As of now, a 15 mA DC, 30-keV H- ion source, a 2 m-long Low Energy Beam Transport (LEBT), a 2.1 MeV CW RFQ, followed by a 10 m Medium Energy Beam Transport (MEBT) have been assembled and commissioned. The MEBT bunch-by-bunch chopping system and the requirement of a low uncontrolled beam loss put stringent limitations on the beam envelope and its variation. Measurements of transverse and longitudinal beam dynamics in the MEBT were performed in the range of 1- 10 mA of the RFQ beam current. Almost all measurements are made with 10 μs beam pulses in order to avoid damage to the beam line. This report presents measurements of the transverse optics with differential trajectories, reconstruction of the beam envelope with scrapers and an Allison emittance scanner, as well as bunch length measurements with a Fast Faraday Cup.

43 PARTICLE ACCELERATORS↗

Quench protection of the first 4 m long prototype of the HL-LHC Nb3Sn quadrupole magnet

The quadrupole magnets for the LHC upgrade to higher luminosity are jointly developed by CERN and US-LARP (LHC Accelerator Research Program). These Nb3Sn magnets will be protected against overheating after a quench by a combination of heaters bonded to the coil outer surface and CLIQ (Coupling-Loss Induced Quench) units. The first 4 meter long prototype magnet, called MQXFAP1, was tested at the Brookhaven National Laboratory in stand-alone configuration. The magnet training campaign, consisting of 18 quenches, was interrupted due to the development of a short circuit between one heater strip and the coil. During the campaign, different quench protection schemes were implemented, including heaters attached to outer and inner layers, one CLIQ unit, and the energy-extraction system. The configuration including outer-layer heaters and CLIQ achieved the fastest current discharge, hence the lowest hot-spot temperature. The electro-magnetic and thermal transients after a quench were simulated with the program STEAM-LEDET and found in good agreement.

43 PARTICLE ACCELERATORS↗

Vertical Magnetic Measurement System Commis-sioning and First Measurements of the First Full-Length Prototype Quadrupole Magnet for the LHC Hi-Lumi Upgrade

This paper will report the commissioning of the vertical magnetic measurement system and the warm (room temperature) and cold (cryogenic) magnetic field measurements of the first full-length (4.2 m) quadrupole built by the US Accelerator Upgrade Project (AUP) project (formerly the LARP collaboration) for the high luminosity upgrade of the Large Hadron Collider at CERN. The magnet, designated MQXFAP2, is a prototype preceding production for the AUP Accelerator Upgrade Project (AUP). AUP will provide ten 8.4 m superconducting insertion region (IR) quadrupoles for the Hi-Lumi Upgrade. The 8.4 m quadrupoles will be built by assembling two 4.2 m magnets in a single cryostat. Agreement between BNL’s and LBNL’s warm measurement data has indicated that the upgraded vertical magnetic measurement system at BNL is ready for MQXFA magnet production testing. The cold magnetic measurement has been performed and preliminary data analysis has been conducted. The measured data indicates that the MQXFAP2 magnet has good magnetic field which meets the preliminary MQXFA magnet acceptance criteria.

43 PARTICLE ACCELERATORS↗

Prototyping the BOPTEST Framework for Simulation-Based Testing of Advanced Control Strategies in Buildings

Advanced control strategies are becoming increasingly necessary in buildings in order to meet and balance requirements for energy efficiency, demand flexibility, and occupant comfort. Additional development and widespread adoption of emerging control strategies, however, ultimately require low implementation costs to reduce payback period and verified performance to gain control vendor, building owner, and operator trust. This is difficult in an already first-cost driven and risk-averse industry. Recent innovations in building simulation can significantly aid in meeting these requirements and spurring innovation at early stages of development by evaluating performance, comparing state-of-the-art to new strategies, providing installation experience, and testing controller implementations. This paper presents the development of a simulation framework consisting of test cases and software platform for the testing of advanced control strategies (BOPTEST - Building Optimization Performance Test). The objectives and requirements of the framework, components of a test case, and proposed software platform architecture are described, and the framework is demonstrated with a prototype implementation and example test case.

Blum, David↗

Performance of Dressed Cavities for the Jefferson Laboratory LCLS-II Prototype Cryomodule - With Comparison to the Pre-Dressed Performance

Initial vertical RF test results and quench studies for six of the eight undressed 9 cell cavities slated for use in the Jefferson laboratory LCLS-II prototype cryomodule were presented at IPAC2015*. For the final string 2 more cavities AES029 and AES030 (work done at Cornell) are being processed and tested for qualification before helium vessel welding. In addition, AES034 (initial R&D treatment) is being reworked with the current production protocol after a surface reset to improve the overall performance. After final qualification all 8 cavities will be welded into helium vessels and equipped with HOM couplers. In this paper we will present the final undressed and dressed vertical RF data comparing the changes in the surface resistance before their installation in the cryomodule string.

Palczewski, Ari D.↗

Ocean Testing of the Azura Prototype Wave Energy Converter in Hawaii.

The Azura scaled prototype has successfully completed 19 months of grid-connected open ocean testing at the US Navy’s Wave Energy Test Site (WETS) in Kaneohe, Hawaii. The Azura was deployed from June 2015 to December 2016. Data collection and processing was done by The Hawaii Natural Energy Institute, providing independent data validation. Figure 1 shows the Azura deployed at WETS. The test concluded with some major accomplishments, including validation of computer simulations, demonstration of a robust design, and marine operations experience.

16 TIDAL AND WAVE POWER↗

Performance of first prototype multi-cell low-surface-field shape cavity

The idea of cavity shaping for higher ultimate acceleration gradients has been proposed for some time, Low Loss/Ichiro and Re-entrant being examples, both seeking a lower Hpk/Eacc at the expense of a higher Epk/Eacc. While experimental verification in single-cell cavities of those shapes was very successful including the record gradient of 59 MV/m, pushing multi-cell cavities of those shapes to higher gradients was prevented by field emission. The Low-Surface-Field (LSF) shape seeks not only a lower Hpk/Eacc but also a lower Epk/Eacc, therefore it has the advantage of raising ultimate gradient at reduced field emission. The first multi-cell LSF shape prototype cavity was built using the standard forming and welding techniques. RF tests have been carried out, following standard ILC TDR baseline surface processing and treatment recipe. Three out of five cells achieved Hpk values corresponding to Eacc 50 MV/m. The current limit is the field emission in end cells. Instrumented testing following end-cell wiping and HPR with larger nozzles is in progress. We will present detailed experimental results and preparation procedures.

Geng, R.-L.↗

Prototypical Region Proposal Networks for Few-Shot Localization and Classification

Recently proposed few-shot image classification methods have generally focused on use cases where the objects to be classified are the central subject of images. Despite success on benchmark vision datasets aligned with this use case, these methods typically fail on use cases involving densely-annotated, busy images: images common in the wild where objects of relevance are not the central subject, instead appearing potentially occluded, small, or among other incidental objects belonging to other classes of potential interest. To localize relevant objects, we employ a prototype-based few-shot segmentation model which compares the encoded features of unlabeled query images with support class centroids to produce region proposals indicating the presence and location of support set classes in a query image. These region proposals are then used as additional conditioning input to few-shot image classifiers. We develop a framework to unify the two stages (segmentation and classification) into an end-to-end classification model---PRoPnet---and empirically demonstrate that our methods improve accuracy on image datasets with natural scenes containing multiple object classes.

Skomski, Steven E.↗

$S$ parameter from a prototype composite-Higgs model

We have calculated the low-energy constant $L_{10}$ in a prototype composite Higgs model with dynamical fermions in two different representations of the gauge group. The resulting contribution of the new strong sector to the $S$ parameter is consistent with current bounds on the vacuum misalignment parameter. We end with a brief discussion of future directions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Fuel Refabrication Prototype - Presentation for 2021 ASI Annual Webinar

This power point presentation is a summary of the work produced in FY2021 under the LWR Fuel Reinstrumentation project funded by DOE's Advanced Sensor Initiative, and the outlook for FY22. The objective of this portion of the ASI program is to "Capture critical technology created by the Institute For Energy (formerly Halden Reactor Project) to reinstrument irradiated fuel rodlets, and further this technology to enable incorporation of advanced instrumentation: fiberoptics, LVDTs, ultrasonic based sensors". The presentation explains that two of the three equipment modules were received and INL and a number of practice runs were conducted with them. In FY22 the third equipment module will arrive and using the three equipment modules measurement sciences personnel will create a complete prototypical instrumented fuel rodlet (using ceramic surrogates in the place of UO2).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

2021 Prototype Manufacture and Installation Awardee: Pecos Wind Power, Inc.

Through the 2021 Competitiveness Improvement Project (CIP), Pecos Wind Power will manufacture a prototype of its 85-kilowatt (kW) horizontal-axis distributed wind turbine, the PW85, a new wind turbine that began development in 2017 when the company was founded. The PW85 wind turbine includes an industry-leading rotor diameter (30 meters) and full-span variable pitch blades to target a levelized cost of energy (LCOE) of $0.103/kilowatt-hour in low annual wind speeds (6 meters per second). This is 55% lower than the average small wind turbine project installed in 2018. The goal of this project is to spur the development of increasingly lower-cost, high-capacity-factor distributed wind turbines. As a result, Pecos Wind Power will manufacture and install wind turbines that increase the geographic area in which distributed wind power is cost competitive with retail-priced electricity and other distributed energy resources - primarily solar energy.

CIP↗

2021 Prototype Installation and Testing Awardee: XFlow Energy Company

XFlow Energy Company (XFlow Energy) aims to reduce the cost of wind energy by designing vertical-axis wind turbines (VAWTs), which have a cheaper blade manufacturing process and a mechanically simpler design than traditional wind turbines, among other cost-saving advantages. However, a lack of modeling or simulation tools that can predict the coupling between aerodynamic and structural forces poses a significant challenge to developers of VAWTs. Known as aeroelastic models, these are not just important design tools - they're critical for certifying VAWTs of 25 kilowatts (kW), which is the size of XFlow Energy's prototype wind turbine. Without certification, XFlow Energy will not be able to deliver an independently validated product to its customers, and those customers will not be eligible for state and federal incentives. An accurate aeroelastic model could provide less-conservative structural optimization tactics than are currently used, resulting in a wind turbine with lower capital costs.

CIP↗

Development and Performance of RFD Crab Cavity Prototypes for HL-LHC AUP

The US will be contributing to the HL-LHC upgrade at CERN with the fabrication and qualification of RFD crabbing cavities in the framework of the HL-LHC Accelerator Upgrade Project (AUP) managed by Fermilab. AUP received Critical Decision 3 (CD-3) approval by DOE in December 2020 launching the project into the production phase. The electro-magnetic design of the cavity was inherited from the LHC Accelerator Research Program (LARP) but needed to be revised to meet new project requirements and to prevent issues encountered during beam tests performed at CERN in the R&D phase. Two prototype cavities were manufactured in industry and cold tested. Challenges specific to the RFD cavity were the stringent interface tolerances, the pole symmetry, and the higher-order-mode impedance spectrum. Chemical processing and heat treatments were performed initially at FNAL/ANL and are now being transferred to industry for the production phase. HOM dampers are manufactured and validated by JLAB. A summary of cold test results with and without HOM dampers is presented.

43 PARTICLE ACCELERATORS↗

The ETROC2 prototype for CMS MTD Endcap Timing Layer (ETL) upgrade

The Endcap Timing ReadOut Chip (ETROC) is designed to process LGAD signals with time resolution down to about 40-50ps per hit. The ETROC2 is the first full size (16x16) prototype design with the front-end based on and scaled up from the ETROC1 (4x4). The readout designs at pixel and global level and the system interfaces are all new and are compatible with the final chip specifications in terms of functionality. The ETROC2 is intended as a learning chip, as a stepstone to the ETROC3 which is intended as the pre-production design. The ETROC2 design and test results will be presented.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Preliminary Results for Uncertainty Quantification on Asymptotic Hydrogen Redistribution in a Prototypical Yttrium-Hydride Moderated Heat-Pipe-Cooled Microreactor

Yttrium hydride is one of the most promising materials for moderating nuclear microreactors. This is due to its high hydrogen concentration at high operating conditions, high value of thermal conductivity, and chemical stability. However, when subject to thermal and concentration spatial gradients, the hydrogen tends to migrate within the yttrium matrix, potentially leading to power swings and reactivity changes. This paper aims to present selected results concerning the sensitivity of the thermal and hydrogen redistribution response for a prototypical heat-pipe-cooled yttrium-hydride moderated microreactor to thermal properties uncertainty and selected design characteristics. To the best knowledge of the authors, this is the first study examining the impact of uncertainties on microreactor hydrogen redistribution response. To achieve this goal, Bison was used in conjunction with Dakota to create a framework able to perform Uncertainty Quantification (UQ) for the Simplified Microreactor Benchmark Assessment (SiMBA) problem.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Innovative power conversion system for the French SFR prototype, ASTRID

In the framework of the French Act of 28 June 2006 about nuclear materials and waste management, the prototype ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration), foreseen in operation by the 20's, will have to demonstrate not only the minor actinide transmutation capability, but also the progress made in Sodium Fast Reactor (SFR) technology on an industrial scale, by qualifying innovative options. Some of these options still require improvements, especially in the field of operability and safety. In fact, one of the main issues with the standard steam/water Power Conversion System (PCS) of SFR is the fast and energetic chemical reaction between water and sodium, which could occur in steam generators in case of tube failure. To manage the sodium/water reaction, one way consists in minimizing the impact of such event: hence studies are carried out on steam generator design, improvement of the physical knowledge of this phenomenon, development of numerical simulation to predict the reaction onset and consequences, and associated detection improvement. On the other hand, the other way consists in eliminating sodium/water reaction. In this frame, the CEA contribution to the feasibility evaluation of an alternative innovative PCS (replacing steam/water by 180 bar pressurised nitrogen) is focused on the following main topics: - The parametric study leading to nitrogen selection: the thermodynamic cycle efficiency optimisation on Brayton cycles is performed with several gases at different pressures. - The design of innovative compact heat exchangers for the gas loop: here the key points are the nuclear codification associated with inspection capability, the innovative welding process and the thermal-hydraulic and thermal-mechanic optimisations. After a general introduction of the ASTRID project, this paper presents in detail these different feasibility studies being led on the innovative gas PCS for an SFR. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A decision support system prototype including human factors based on the TOGA meta-theory approach

The human contribution to the risk of operation of complex technological systems is often not negligible and sometimes tends to become significant, as shown by many reports on incidents and accidents occurred in the past inside Nuclear Power Plants (NPPs). An error of a human operator of a NPP can derive by both omission and commission. For instance, complex commission errors can also lead to significant catastrophic technological accidents, as for the case of the Three Mile Island accident. Typically, the problem is analyzed by focusing on the single event chain that has provoked the incident or accident. What is needed is a general framework able to include as many parameters as possible, i.e. both technological and human factors. Such a general model could allow to envisage an omission or commission error before it can happen or, alternatively, suggest preferred actions to do in order to take countermeasures to neutralize the effect of the error before it becomes critical. In this paper, a preliminary Decision Support System (DSS) based on the so-called (-) TOGA meta-theory approach is presented. The application of such a theory to the management of nuclear power plants has been presented in the previous ICAPP 2011. Here, a human factor simulator prototype is proposed in order to include the effect of human errors in the decision path. The DSS has been developed using a TRIGA research reactor as reference plant, and implemented using the LabVIEW programming environment and the Finite State Machine (FSM) model The proposed DSS shows how to apply the Universal Reasoning Paradigm (URP) and the Universal Management Paradigm (UMP) to a real plant context. The DSS receives inputs from instrumentation data and gives as output a suggested decision. It is obtained as the result of an internal elaborating process based on a performance function. The latter, describes the degree of satisfaction and efficiency, which are dependent on the level of responsibility related to each professional role. As an application, we present the simulation of the discussed error, e.g. the unchecked extraction of the control rods during a power variation maneuver and we show how the effect of human errors can affect the performance function, giving rise to different countermeasures which could call different operator figures into play, potentially not envisaged in the standard procedure. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Application of the JENDL-4.0 nuclear data set for uncertainty analysis of the prototype FBR Monju

This paper deals with uncertainty analysis of the Monju reactor using JENDL-4.0 and the ERANOS code 1. In 2010 the Japan Atomic Energy Agency - JAEA - released the JENDL-4.0 nuclear data set. This new evaluation contains improved values of cross-sections and emphasizes accurate covariance matrices. Also in 2010, JAEA restarted the sodium-cooled fast reactor prototype Monju after about 15 years of shutdown. The long shutdown time resulted in a build-up of {sup 241}Am by natural decay from the initially loaded Pu. As well as improved covariance matrices, JENDL-4.0 is announced to contain improved data for minor actinides 2. The choice of Monju reactor as an application of the new evaluation seems then even more relevant. The uncertainty analysis requires the determination of sensitivity coefficients. The well-established ERANOS code was chosen because of its integrated modules that allow users to perform sensitivity and uncertainty analysis. A JENDL-4.0 cross-sections library is not available for ERANOS. Therefor a cross-sections library had to be made from the original ENDF files for the ECCO cell code (part of ERANOS). For confirmation of the newly made library, calculations of a benchmark core were performed. These calculations used the MZA and MZB benchmarks and showed consistent results with other libraries. Calculations for the Monju reactor were performed using hexagonal 3D geometry and PN transport theory. However, the ERANOS sensitivity modules cannot use the resulting fluxes, as these modules require finite differences based fluxes, obtained from RZ SN-transport or 3D diffusion calculations. The corresponding geometrical models have been made and the results verified with Monju restart experimental data 4. Uncertainty analysis was performed using the RZ model. JENDL-4.0 uncertainty analysis showed a significant reduction of the uncertainty related to the fission cross-section of Pu along with an increase of the uncertainty related to the capture cross-section of {sup 238}U compared with the previous JENDL-3.3 version. Covariance data recently added in JENDL-4.0 for {sup 241}Am appears to have a non-negligible contribution. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗