Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Aligned Carbon Nanotube Reinforced Silicon Carbide Composites by Chemical Vapor Infiltration

Owing to their exceptional stiffness and strength1 4, carbon nanotubes (CNTs) have long been considered to be an ideal reinforcement for light-weight, high-strength, and high-temperature-resistant ceramic matrix composites (CMCs)5 10. However, the research and development in CNT-reinforced CMCs have been greatly hindered due to the challenges related to manufacturing including poor dispersion, damages during dispersion, surface modification, densification and sintering, weak tube/matrix interfaces, and agglomeration of tubes at the matrix grain boundaries5,11. Here we report the fabrication of high-quality aligned CNT/SiC composites by chemical vapor infiltration (CVI), a technique that is being widely used to fabricate commercial continuous-filament CMCs12 15. Using the CVI technique most of the challenges previously encountered in the fabrication of CNT composites were readily overcome. Nanotube pullouts, an important toughening mechanism for CMCs, were consistently observed on all fractured CNT/SiC samples. Indeed, three-point bending tests conducted on individual CNT/SiC nanowires (diameters: 50 200 nm) using an atomic force microscope show that the CNT-reinforced SiC nanowires are about an order of magnitude tougher than the bulk SiC. The tube/matrix interface is so intimate and the SiC matrix is so dense that a ~50-nm-thick SiC coating can effectively protect the inside nanotubes from being oxidized at 1600 C in air. The CVI method may be extended to produce nanotube composites from a variety of matrix

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Quantitative analysis of inclusion distributions in hot pressed silicon carbide

ABSTRACT Depth of penetration measurements in hot pressed SiC have exhibited significant variability that may be influenced by microstructural defects. To obtain a better understanding regarding the role of microstructural defects under highly dynamic conditions; fragments of hot pressed SiC plates subjected to impact tests were examined. Two types of inclusion defects were identified, carbonaceous and an aluminum-iron-oxide phase. A disproportionate number of large inclusions were found on the rubble, indicating that the inclusion defects were a part of the fragmentation process. Distribution functions were plotted to compare the inclusion populations. Fragments from the superior performing sample had an inclusion population consisting of more numerous but smaller inclusions. One possible explanation for this result is that the superior sample withstood a greater stress before failure, causing a greater number of smaller inclusions to participate in fragmentation than in the weaker sample.

36 MATERIALS SCIENCE↗

Synthesis and properties of bulk cobalt-carbide permanent magnets

Nanocrystalline bulk Co-C permanent magnets were produced by rapid hot consolidation of ball milled powder precursors. Bulk magnets with an average grain size of 20 nm and densities up to 94 percent of the theoretical density were successfully processed at pressures exceeding 1 GPa for the first time. Their microstructural and magnetic properties along with their magnetocrystalline anisotropy values are reported. Presence of iron contamination that results from the use steel milling media in milling was confirmed by elemental mapping of the bulk magnets. It is concluded that iron bonds in the form of hematite and does not adversely affect coercivity values. Here, this study shows that the Co 3 C compound does possess a sizable magnetocrystalline anisotropy, making it a suitable candidate as a rare earth free permanent magnet.

Co3 C↗

Nuclear reaction analysis of helium migration in silicon carbide

4H-SiC and 6H-SiC single crystals were implanted at room temperature with 3-MeV 3He ions at a fluence of 1x1016 cm-2. Analysis of helium migration was carried out with the 3He(d, p)4He nuclear reaction. No clear thermally-activated migration in the end-of-range (EOR) region is found below 1100 C, meaning that helium is strongly trapped probably in helium-vacancy clusters. At 1100 C and above, a fraction of 3He atoms remains trapped in the clusters, but a significant fraction is detrapped into a broad distribution, which is slightly shifted towards the sample surface. Helium detrapping from the EOR region increases with increasing annealing time and temperature. Moreover, the helium content is not conserved, since a significant fraction of 3He atoms is released out of the sample. Helium out-gassing actually increases with increasing annealing time and temperature, up to about 40% at 1150 C. No clear difference is found between the 4H-SiC and 6H-SiC polytypes.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Challenges and opportunities to alloyed and composite fuel architectures to mitigate high uranium density fuel oxidation: Uranium diboride and uranium carbide

Here, the challenges and opportunities to alloyed and composite fuel architectures designed and intended to mitigate oxidation of the fuel during a cladding breach of a water-cooled reactor are discussed in three review manuscripts developed in parallel, with the presented article focused on the oxidation performance of uranium diboride and uranium monocarbide. Several high uranium density fuels are under consideration for deployment as accident tolerant and/or advanced technology nuclear reactor fuels, including UN, U 3 Si 2 , UB 2 , and UC. Presented here is the literature for UB 2 and UC degradation modes, thermodynamics, and oxidation performance of the pure compounds and reported alloyed and composite architectures. Furthermore, this review covers the materials and techniques for the incorporation of additives, dopants, or composite fuel architectures to improve the oxidation behavior for high uranium density fuels for use in LWRs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Stoichiometric effects on grain growth in zirconium carbide coatings for high-temperature nuclear fuel

Interest in coated particle fuel for space nuclear propulsion (SNP) has expanded in recent years due to successful demonstrations of the resiliency of the coatings to extreme environments. For SNP applications, the coating layer for the particle design needs to be able to withstand exposure to high temperature hydrogen during operating conditions. ZrC has been proposed as a protective layer, however, it is important to understand the high temperature behavior to ensure adequate protection to this fuel. In this study, surrogate ZrC coated particles were heat treated at 1900 °C up to 300 min, to examine how the microstructure evolves when exposed to high temperature. Scanning electron microscopy and electron backscatter diffraction (EBSD) were conducted to determine grain size and grain boundary character and orientation to determine the degree of change in the ZrC layer post heat treatment. Raman spectroscopy provided insight to understand how the as-fabricated stoichiometry of each sample contributed to the differences in grain growth behavior. Despite the as-fabricated samples showing a similar initial grain size and grain boundary character, the samples with a higher amount of excess carbon exhibited smaller grain areas and slower growth rates when exposed to 1900 °C. In conclusion, this investigation details the as-fabricated microstructure of the ZrC layer, specifically grain size, evolved under high temperature as this can impact the performance of the fuel under operating conditions.

EBSD↗

Tungsten Carbide Modified High Surface Area Carbon as Fuel Cell Catalyst Support

Phase pure WC nanoparticles were synthesized on high surface area carbon black (800 m{sup 2} g{sup -1}) by a temperature programmed reaction (TPR) method. The particle size of WC can be controlled under 30 nm with a relatively high coverage on the carbon surface. The electrochemical testing results demonstrated that the corrosion resistance of carbon black was improved by 2-fold with a surface modification by phase pure WC particles. However, the WC itself showed some dissolution under potential cycling. Based on the X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis, most of the WC on the surface was lost or transformed to oxides after 5000 potential cycles in the potential range of 0.65-1.2 V. The Pt catalyst supported on WC/C showed a slightly better ORR activity than that of Pt/C, with the Pt activity loss rate for Pt/WC/C being slightly slower compared to that of Pt/C. The performance and decay rate of Pt/WC/C were also evaluated in a fuel cell.

30 DIRECT ENERGY CONVERSION↗

Microstructures of the silicon carbide nanowires obtained by annealing the mechanically-alloyed amorphous powders

Silicon, graphite and boron nitride powders were mechanically alloyed for 40 h in argon. The as-milled powders were annealed at 1700 °C in nitrogen for 30 min. The annealed powders are covered by a thick layer of gray–green SiC nanowires, which are 300 nm to 1000 nm in diameter and several hundred microns in length. Trace iron in the raw powders acts as a catalyst, promoting the V–L–S process. It follows that the actual substances contributing to the growth of the SiC nanowires may be silicon, graphite and the metal impurities in the raw powders. The results from HRTEM and XRD reveal that the products contain both straight α/β-SiC nanowires and nodular α/β-SiC nanochains. It is interestingly found that 6H–SiC coexists with 3C–SiC in one nodular nanowire. This novel structure may introduce periodic potential field along the longitudinal direction of the nanowires, and may find applications in the highly integrated optoelectronic devices. - Graphical abstract: Display Omitted - Highlights: • SiC nanowires were prepared by annealing the mechanically alloyed amorphous powders. • SiC nanowires are 300 nm to 1000 nm in diameter and several hundred microns in length. • The products contain both straight α/β-SiC nanowires and nodular α/β-SiC nanochains. • Trace Fe in the raw powders acts as a catalyst, promoting the V–L–S process. • 6H–SiC coexists with 3C–SiC in one nodular SiC nanowire.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Mechanisms of stored energy release in silicon carbide materials neutron-irradiated at elevated temperatures

Understanding the stored energy release behavior of SiC is crucial for the design of SiC-based fuel cladding for light water reactors because stored energy release affects response during accident conditions. Differential scanning calorimetry was used to evaluate the stored energy of monolithic SiC and SiC fiber–reinforced SiC matrix composite variants following neutron irradiation under light water reactor–relevant dose and temperature conditions. The tests were performed at heating rates of 0.5, 3, and 20 K/min up to 1,273 K. The onset temperature of the energy release roughly corresponded to the irradiation temperature, and energy release was delayed as the heating rate increased. The monolithic and composite specimens exhibited similar stored energy release behavior up to ~1,000 K, and above that temperature, the energy release depended more on material type. The energy release measured in this study is below the material-specific heat capacity at temperatures below ~1,000 K but exceeds it under certain material and annealing conditions at temperatures above ~1,000 K. The amount of irradiation-induced volumetric swelling of the specimens was an indication of the total stored energy. Based on this observation, the energy release behavior was described by a swelling recovery model.

36 MATERIALS SCIENCE↗

Combustion synthesis of silicon carbide assisted by a magnesium plus polytetrafluoroethylene mixture

In this study, the use of SiC combustion synthesis for immobilization of {sup 14}C was considered. Due to the low exothermicity of the reaction between silicon and graphite, a highly exothermic mixture (magnesium and polytetrafluoroethylene) was used both as a chemical oven and activate additive in the mixture. With this configuration the reaction between graphite and silicon was initiated and propagated on the whole sample. The self-propagating high temperature synthesis samples were characterized by using scanning electron microscopy and X-ray diffraction.

36 MATERIALS SCIENCE↗

Modeling thermal spike driven reactions at low temperature and application to zirconium carbide radiation damage

The development of TEM-visible damage in materials under irradiation at cryogenic temperatures cannot be explained using classical rate theory modeling with thermally activated reactions since at low temperatures thermal reaction rates are too low. Although point defect mobility approaches zero at low temperature, the thermal spikes induced by displacement cascades enable some atom mobility as it cools. In this work a model is developed to calculate “athermal” reaction rates from the atomic mobility within the irradiation-induced thermal spikes, including both displacement cascades and electronic stopping. The athermal reaction rates are added to a simple rate theory cluster dynamics model to allow for the simulation of microstructure evolution during irradiation at cryogenic temperatures. The rate theory model is applied to in-situ irradiation of ZrC and compares well at cryogenic temperatures. The results show that the addition of the thermal spike model makes it possible to rationalize microstructure evolution in the low temperature regime.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Understanding Functionalization of Titanium Carbide (MXene) with Quinones and Their Pseudocapacitance

In this work, the interaction mechanism of 1-aminoanthraquinone (AQ) on Ti 3 C 2 T x MXene by noncovalent (AQ@Ti 3 C 2 T x ) and covalent (AQ-Ti 3 C 2 T x ) functionalization is reported. Spectroscopic, X-ray, and scattering techniques confirmed noncovalent functionalization of AQ on Ti 3 C 2 T x MXene without its catalytic decomposition, resulting in intercalation and interaction of AQ with Ti 3 C 2 T x MXene. Diazonium reaction was further used to covalently functionalize AQ molecules on Ti 3 C 2 T x MXene. Optimized AQ-Ti 3 C 2 T x freestanding electrodes of ~44 μm thickness delivered capacitance of ~300 F/g and improved rate performance compared to the pristine counterpart (Ti 3 C 2 T x ) due to carbonyl redox of AQ and improved ionic transport between MXene layers due to pillaring of AQ molecules.

36 MATERIALS SCIENCE↗