Evolution of local lattice distortion under irradiation in medium- and high-entropy alloys
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
An important consequence of the fissioning process occurring during burnup is the formation of fission products. These fission products alter the thermo-mechanical properties of the fuel. They also lead to macroscopic changes in the fuel structure, including the formation of bubbles that are connected to swelling of the fuel. Subsequent release of fission gases increase the pressure in the plenum and can cause changes in the properties of the fuel pin itself. It is thus imperative to understand how fission products, and fission gases in particular, behave within the fuel in order to predict the performance of the fuel under operating conditions. Fission gas redistribution within the fuel is governed by mass transport and the presence of sinks such as impurities, dislocations, and grain boundaries. Thus, to understand how the distribution of fission gases evolves in the fuel, we must understand the underlying transport mechanisms, tied to the concentrations and mobilities of defects within the material, and how these gases interact with microstructural features that might act as sinks. Both of these issues have been addressed in previous work under NEAMS. However, once a fission product has reached a sink, such as a grain boundary, its mobility may be different there than in the grain interior and predicting how, for example, bubbles nucleate within grain boundaries necessitates an understanding of how fission gases diffuse within boundaries. That is the goal of the present work. In this report, we describe atomic level simulations of uranium vacancy diffusion in the pressence of a Σ5 symmetric tilt boundary in urania (UO 2 ). This boundary was chosen as it is the simplest of the boundaries we considered in previous work on segregation and serves as a starting point for understanding defect mobility at boundaries. We use a combination of molecular statics calculations and kinetic Monte Carlo (kMC) to determine how the mobility of uranium vacancies is altered at this particular grain boundary. Given that the diffusion of fission gases such as Xe are tied to the mobility of uranium vacancies, these results given insight into how fission gas mobility differs at grain boundaries compared to bulk urania.
Nanostructuring of thermoelectric materials is expected to enhance thermoelectric properties by reducing the thermal conductivity and improving the power factor from that of homogeneous bulk materials. In multiphase, nanostructured thermoelectric materials, an understanding of precipitation mechanisms and phase stability is crucial for engineering systems with optimal thermoelectric performance. In this presentation we will discuss our investigations of the morphological evolution, orientation relationship, and composition of Ag{sub 2}Te precipitates in PbTe using transmission electron microscopy (TEM) and atom probe tomography (APT). Annealing in the region of two phase equilibrium between Ag{sub 2}Te and PbTe results in the formation of monoclinic {beta}-Ag{sub 2}Te precipitates as determined by x-ray and electron diffraction studies. These precipitates are aligned to the PbTe matrix with an orientation relationship that aligns the Te sub-lattices in the monoclinic and rock salt structures. This relationship is the same as we have reported earlier for {beta}-Ag{sub 2}Te precipitates in rocksalt AgSbTe{sub 2}. Observations using TEM and APT suggest that the Ag{sub 2}Te precipitates initially form as coherent spherical precipitates which upon coarsening evolve into flattened semi-coherent disks along the <100>PbTe directions which is consistent with theoretical predictions for elastically strained precipitates in a matrix. Our HRTEM observations show that sufficiently small precipitates are coherently embedded, while larger precipitates exhibit misfit dislocations and multiple monoclinic variants to relieve the elastic strain. Analysis of the composition of both precipitate groups using APT indicates that the larger precipitates exhibit compositions close to equilibrium while the smaller nanoscale precipitates exhibit enhanced Pb compositions. This detailed analysis of the orientation relationship, morphology, composition, and coarsening behavior of embedded Ag{sub 2}Te precipitates may be helpful in understanding the precipitation mechanisms and microstructure of related thermoelectric materials, such as LAST.
Mechanical properties and creep resistance of the MgY4Zn1Mn1 alloy in the as cast as well as in the T5 condition were compared to those of the MgCe4Zn1Mn1 alloy in the same conditions. Yield tensile stress and ultimate tensile strength of the MgY4Zn1Mn1 alloy are slightly better in the temperature range 20 deg. C-400 deg. C than these of the MgCe4Zn1Mn1 alloy. Better thermal stability of ultimate tensile strength was observed in the T5 treated MgCe4Zn1Mn1 alloy than in this material in the as cast condition. An outstanding creep resistance at 225 deg. C-350 deg. C found in the MgY4Zn1Mn1 alloy is due to the existence of the 18R long period stacking structure persisting in this alloy even a long heat treatment of 500 deg. C/32 h. No similar stacking effects happen when Ce substitutes Y in approximately the same concentration. The creep resistance deteriorates considerably in the MgCe4Zn1Mn1 alloy. Rectangular particles of the equilibrium Mg{sub 12}Ce phase dominate in the microstructure of as cast as well as of high temperature heat-treated MgCe4Zn1Mn1 alloy. A population of small oval particles containing Mg and Zn develops additionally during annealing of this alloy. These particles pin effectively dislocations and can be responsible for the better thermal stability of the T5 treated material.
A molecular dynamics simulation approach is presented to approximate layered material structures using discrete interatomic potentials through classical mechanics and the underlying principles of quantum mechanics. This method isolates the energetic contributions of the system into two pure material layers and an interfacial region used to simulate the adhesive properties of the diffused interface. The strength relationship of the adhesion contribution is calculated through small-scale separation calculations and applied to the molecular surfaces through an inter-layer bond criterion. By segregating the contributions into three regions and accounting for the interfacial excess energies through the adhesive surface bonds, it is possible to model each material with an independent potential while maintaining an acceptable level of accuracy in the calculation of mechanical properties. This method is intended for the atomistic study of the delamination mechanics, typically observed in thin-film applications. Therefore, the work presented in this paper focuses on mechanical tensile behaviors, with observations in the elastic modulus and the delamination failure mode. To introduce the hybrid adhesion method, we apply the approach to an ideal bulk copper sample, where an interface is created by disassociating the force potential in the middle of the structure. Various mechanical behaviors are compared to a standard EAM control model to demonstrate the adequacy of this approach in a simple setting. In addition, we demonstrate the robustness of this approach by applying it on (1) a Cu-Cu 2 O interface with interactions between two atom types, and (2) an Al-Cu interface with two dissimilar FCC lattices. These additional examples are verified against EAM and COMB control models to demonstrate the accurate simulation of failure through delamination, and the formation and propagation of dislocations under loads. Finally, the results conclude that by modeling the energy contributions of an interface using hybrid adhesion bonds, we can provide an accurate approximation method for studies of large-scale mechanical properties, as well as the representation of various delamination phenomena at the atomic scale.
Many microscopic investigations of materials may benefit from the recording of multiple successive images. This can include techniques common to several types of microscopy such as frame averaging to improve signal-to-noise ratios (SNR) or time series to study dynamic processes or more specific applications. In the scanning transmission electron microscope, this might include focal series for optical sectioning or aberration measurement, beam damage studies or camera-length series to study the effects of strain; whilst in the scanning tunnelling microscope, this might include bias voltage series to probe local electronic structure. Whatever the application, such investigations must begin with the careful alignment of these data stacks, an operation that is not always trivial. In addition, the presence of low-frequency scanning distortions can introduce intra-image shifts to the data. Here, we describe an improved automated method of performing non-rigid registration customised for the challenges unique to scanned microscope data specifically addressing the issues of low-SNR data, images containing a large proportion of crystalline material and/or local features of interest such as dislocations or edges. Careful attention has been paid to artefact testing of the non-rigid registration method used, and the importance of this registration for the quantitative interpretation of feature intensities and positions is evaluated.
Inconel 617 is a solution strengthened nickel-based alloy which has been considered as one of the leading structural material for the intermediate heat exchangers (IHX) in very high temperature reactor (VHTR). In order to gain understanding of the creep and fatigue deformation mechanisms and their interactions in alloy 617 operating in the VHTR environment, a computational model that operates at the microstructural scale has been developed for creep, fatigue and creep-fatigue modeling of alloy 617. This model is based on an isothermal, large deformation crystal plasticity finite element (CPFE) formulation and idealizes the deformation in the crystal lattice as collective glide and climb of dislocations. A recently developed glide resistance evolution equation by the authors that can capture the intermediate softening observed in both fatigue and creep-fatigue cycles of Inconel 617 at high temperature is adopted for the dislocation glide formulation. Dislocation climb is incorporated to account for the interactions between dislocations and local point defects at high temperature. The CP equations are solved incrementally as the constitutive relationship in the context of FE analysis on fully resolved microstructure reconstructed from experiment data. Model parameters are calibrated and verified using experimental tests. (authors)
Inlustra Technologies with subcontractor U.C. Santa Barbara conducted a project with the principle goal of demonstrating high internal quantum efficiency blue (430 nm) and green (540nm) light emitting diodes (LEDs) on low-defect density non-polar GaN wafers. Inlustra pursued the fabrication of smooth thick a-plane and m-plane GaN films, as well as defect reduction techniques such as lateral epitaxial overgrowth (LEO) to uniformly lower dislocation density in these films. Limited free-standing wafers were produced as well. By the end of the reporting period, Inlustra had met its milestone of dislocation reduction to < 5 x 10{sup 6} cm{sup -2}. Stacking faults were still present in appreciable density ({approx} 1 x 10{sup 5} cm{sup -1}), but were not the primary focus of defect reduction since there have been no published studies establishing their detrimental effects on LED performance. Inlustra's LEO progress built a solid foundation upon which further commercial development of GaN substrates will occur. UCSB encountered multiple delays in its LED growth and fabrication efforts due to unavoidable facilities outages imposed by ongoing construction in an area adjacent to the metalorganic chemical vapor deposition (MOCVD) laboratory. This, combined with the large amount of ab initio optimization required for the MOCVD system used during the project, resulted in unsatisfactory LED progress. Although numerous blue-green photoluminescence results were obtained, only a few LED structures exhibited electroluminescence at appreciable levels. UCSB also conducting extensive modeling (led by Prof. Van de Walle) on the problem of non-radiative Auger recombination in GaN-based LED structures, which has been posited to contribute to LED efficiency 'droop' at elevated current density. Unlike previous modeling efforts, UCSB's approach was truly a first-principles ab initio methodology. Building on solid numerical foundations, the Auger recombination rates of In{sub x}Ga{sub 1-x}N alloys were calculated from first-principles density-functional and many-body-perturbation theory. The differing mechanisms of inter- and intra-band recombination were found to affect different parts of the emission spectrum. In the blue to green spectral region and at room temperature the Auger coefficient was calculated to be as large as 2 x 10{sup -30} cm{sup 6} s{sup -1}; in the infrared it is even larger. These results indicated that Auger recombination may be responsible for the loss of quantum efficiency that affects InGaN-based light emitters, whether on non-polar or polar crystal planes.
Nanolaminated composites composed of alternate metal and intermetallic or ceramic lamellae exhibit high strength, high strain hardening rate and measurable plasticity at ambient and elevated temperatures. Due to the difference in plastic deformation capability between the two phases, structural instability occurs in hard lamellae associated with buckling when a compression strain is applied parallel to the lamellae. Taking nanoscale Al–Al 2 Cu eutectic alloy as a model system, we develop a mesoscale crystal plasticity (CP) model based on the confined layer slip (CLS) mechanism (referred to as CLS-CP) to understand the buckling behavior of the nanolaminates. In the CLS-CP model, buckling in Al 2 Cu lamellae is constrained by the elastic-plastic deformation of Al lamellae. The critical resolved shear stress for dislocation slip in Al lamellae varies with layer thickness, estimated by the CLS mechanism. To capture the essential features of confined layer slip mechanism that dislocations propagate within the layer and are deposited at the interfaces, plastic deformation in each lamella is the same through the layer thickness. The variation of elastic deformation through the layer thickness is captured through dividing each Al lamella into three or more elements that have the same plastic deformation through the thickness. In comparison, we also conduct standard crystal plasticity modeling in which plastic deformation in the three elements through the layer thickness is calculated individually according to phenomenological power law. In these simulations, plasticity in Al 2 Cu lamellae is modeled with slips on {121} planes due to the slip continuity across the interface, which have been observed in our recent experiments. The CLS-CP model is able to predict mechanical properties of nano-scale lamellar materials. In contrast, the standard CP model is more suitable to study deformation behavior of sub-micro scale lamellar materials. In conclusion, the CLS-CP model calculations reveal that critical compression strain corresponding to buckling increases as layer thickness decreases, which agree with micro-pillar compression tests.
Characterizing the fundamental micromechanisms activated during plastic deformation is critical to explain the macroscopic shock response of materials and develop accurate material models. In this paper, we investigate the orientation dependence, and the mediated slip and twin systems on [100] and [111] bcc molybdenum single crystals shock compressed up to 18 GPa with real-time Laue x-ray diffraction measurements. We report that dislocation slip along the {110} < 111 > and {112} < 111 > systems is the governing deformation mechanism during compression with negligible anisotropy observed at the Hugoniot state. Here, we provide real-time evidence that molybdenum undergoes deformation twinning along {11¯2} < 111 > during shock release.
To this day, trapezoidal defects are found in clusters and high counts in wafers representing the industry standard in terms of material quality being produced. This study sheds light on the nature, origin, behavior, and impact of this defect on device yield and reliability. Trapezoidal defects in 4H-SiC epitaxial layers were investigated by photoluminescence (PL) imaging, scanning electron microscopy (SEM), cathodoluminescence spectrum imaging (CLSI), SEM electron beam induced current (EBIC) imaging, and by transmission electron microscopy (TEM) observation. The bar-shaped stacking faults were identified by the PL and CL measurements with a peak emission wavelength of 420 and 450 nm. An optoelectronic behavioral study based on the recombination enhanced dislocation glide mechanism revealed how expanding dislocations and stacking faults interact with each other. Combining the luminescence and microscopy results, the nature of the stacking faults was identified as being a combination of Shockley-type and Frank-type stacking faults. The TEM analysis showed that these defects originate from the substrate and the stacking sequences of some of the faults were determined as (…2, 4, 2…) and (…2, 3, 2…) in the Zhdanov's notation by high-resolution TEM. The origin of this defect is speculated based on our results and previous reports. The EBIC imaging showed that the high density of SFs in these towers is a strong site of carrier recombination, which presumably has an impact on the transfer characteristics of SiC devices. Furthermore, these defects have shown to impact metal oxide semiconductor field effect transistors electrical performance via an increase in the on-state resistance depending on the coverage percentage of the tower of defects in the active area of the device.
Titanium carbide is used as a primary component in coating materials, thin films for electronic devices, and composites. Here, the structure of coherent and semicoherent interfaces formed between close-packed TiC (111) and Ti (0001) is investigated in classical molecular dynamics simulations. The forces on the atoms in the simulations are determined using a newly developed TiC potential under the framework of the third-generation charge optimized many-body (COMB 3 ) suite of potentials. The work of adhesion energies for the coherent interfaces is calculated and compared with the predictions of density functional theory calculations. In the case of relaxed semicoherent interfaces, a two-dimensional (2D) misfit dislocation network is predicted to form that separates the interface into different regions in which the positions of the atoms are similar to the positions at the corresponding coherent interfaces. After the interface is annealed at an elevated temperature, the climb of edge dislocations is activated which modifies the 2D misfit dislocation network and increases the work of adhesion. These findings can be used as inputs for sequential larger simulation models to understand and predict the macroscopic properties of TiC/Ti interfaces.
The primary objective of this project was to facilitate the dislocation of the interfacial ice layer by employing advanced materials and ultrasonic vibration to reduce ice adhesion strength. This work employed two technical approaches that were thoroughly investigated and previously reported. The effectiveness of these approaches, both individually and in combination, has been quantified, demonstrating notable energy savings. The projected payback period for these enhancements is approximately 2.2 years or less, contingent upon specific energy costs. Furthermore, these advancements hold significant promise for reducing carbon emissions across various equipment scales. This study particularly focused on the ultrasonic deicing technique for diverse structures, utilizing numerical simulations to evaluate performance and potential benefits.
Aluminum matrix composites (AMCs) are designed to enhance the performance of conventional aluminum alloys for engineering applications at both room and elevated temperatures. However, the dynamic phase-specific deformation behavior and load-sharing mechanisms of AMCs at elevated temperatures have not been extensively studied and remain unclear. Here, in situ neutron diffraction experiments are employed to reveal the phase-specific structure evolution of additively manufactured Al6061+TiC composites under compressive loading at 250 °C. It is found that the addition of a small amount of nano-size TiC significantly alters the deformation behavior and increases the strength at 250 °C in comparison to the as-printed Al6061. Unlike the two-stage behavior observed in Al6061, the Al6061+TiC composites exhibit three stages during compression triggered by changes in the interphase stress states. Further analysis of Bragg peak intensity and broadening reveals that the presence of TiC alters the dislocation activity during deformation at 250 °C by influencing dislocation slip planes and promoting dislocation accumulation. These findings provide direct experimental observations of the phase-specific dynamic process in AMCs under deformation at an elevated temperature. The revealed mechanisms provide insights for the future design and optimization of high-performance AMCs.
Fe-Ni-Cr stainless-steels are important structural materials because of their superior strength and corrosion resistance. Atomistic studies of mechanical properties of stainless-steels, however, have been limited by the lack of high-fidelity interatomic potentials. Here in this paper, using density functional theory as a guide, we have developed a new Fe-Ni-Cr embedded atom method potential. We demonstrate that our potential enables stable molecular dynamics simulations of stainless-steel alloys at high temperatures, accurately reproduces the stacking fault energy—known to strongly influence the mode of plastic deformation (e.g., twinning vs. dislocation glide vs. cross-slip)—of these alloys over a range of compositions, and gives reasonable elastic constants, energies, and volumes for various compositions. The latter are pertinent for determining short-range order and solute strengthening effects. Our results suggest that our potential is suitable for studying mechanical properties of austenitic and ferritic stainless-steels which have vast implementation in the scientific and industrial communities.
Understanding the deformation behavior of metallic materials at high strain rates requires the characterization of plasticity contributors such as twins, phase transformed regions, and dislocations. However, predicting the contributions from phase transformation and twinning relies on a complete understanding of the selection of variants for various loading orientations and the evolution of their volume fractions. This manuscript presents a new virtual texture (VirTex) analysis approach to characterize phase transformation and twinning variants in deformed microstructures generated using molecular dynamics (MD) simulations. Furthermore, the VirTex method involves the construction of a rotation matrix to calculate the angle/axis pairs and misorientation angles for each atom in the microstructure. Any changes in the orientation angle from angle/axis pairs and/or structure types are analyzed to determine the nucleation and evolution of variants in the microstructure. The study uses shock deformed single-crystal Fe, Ta, and Cu to analyze the variant selections for phase transformation or twinning or both in BCC and FCC systems. In addition, the VirTex analysis is able to characterize the phase transformation and twinning variants in nanocrystalline Fe and Ta microstructures. Besides characterizing variants, orientation mapping also provides an accelerated and on-the-fly approach for quantifying twin fractions in MD microstructures.
Here, we investigate the formation of extended defects during molecular-dynamics (MD) simulations of GaN and InGaN growth on (0001) and (11$\bar{2}$0) wurtzite-GaN surfaces. The simulated growths are conducted on an atypically large scale by sequentially injecting nearly a million individual vapor-phase atoms towards a fixed GaN surface; we apply time-and-position-dependent boundary constraints that vary the ensemble treatments of the vapor-phase, the near-surface solid-phase, and the bulk-like regions of the growing layer. The simulations employ newly optimized Stillinger-Weber In-Ga-N-system potentials, wherein multiple binary and ternary structures are included in the underlying density-functional-theory training sets, allowing improved treatment of In-Ga-related atomic interactions. To examine the effect of growth conditions, we study a matrix of >30 different MD-growth simulations for a range of InxGa1-xN-alloy compositions (0 ≤ x ≤ 0.4) and homologous growth temperatures [0.50 ≤ T/T* m (x) ≤ 0.90], where T* m (x) is the simulated melting point. Growths conducted on polar (0001) GaN substrates exhibit the formation of various extended defects including stacking faults/polymorphism, associated domain boundaries, surface roughness, dislocations, and voids. In contrast, selected growths conducted on semi-polar (11$\bar{2}$0) GaN, where the wurtzite-phase stacking sequence is revealed at the surface, exhibit the formation of far fewer stacking faults. We discuss variations in the defect formation with the MD growth conditions, and we compare the resulting simulated films to existing experimental observations in InGaN/GaN. Finally, while the palette of defects observed by MD closely resembles those observed in the past experiments, further work is needed to achieve truly predictive large-scale simulations of InGaN/GaN crystal growth using MD methodologies.
The results of studying the crystal structure of regions in silicon, recrystallized during the course of thermomigration of the liquid Si–Al zone in the volume of the silicon substrate, are reported (similar regions doped with an acceptor impurity are used to obtain high-voltage solar cells). X-ray methods (including measurements of both diffraction-reflection curves and topograms) and also high-resolution electron microscopy indicate that single-crystal regions in the form of a series of thin strips or rectangular grids are formed as a result of the thermomigration of liquid zones. Dislocation half-loops are detected in the surface layers of the front and back surfaces of the substrate. (311)-type defects are observed in the recrystallized regions.