Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mix Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Low-Emission Hydrogen Combustors for Gas Turbines Using Lean Direct Injection

One of the key technology challenges for the use of hydrogen in gas turbine engines is the performance of the combustion system, in particular the fuel injectors. To investigate the combustion performance of gaseous hydrogen fuel injectors flame tube combustor experiments were performed. Tests were conducted to measure the nitrogen oxide (NO(x)) emissions and combustion performance at inlet conditions of 588 to 811 K, 0.4 to 1.4 MPa, and equivalence ratios up to 0.48. All the injectors were based on Lean Direct Injection (LDI) technology with multiple injection points and quick mixing. One challenge to hydrogen-based premixing combustion systems is flashback since hydrogen has a reaction rate over 7 times that of Jet-A. To reduce the risk, design mixing times were kept short and velocities high to minimize flashback. Five fuel injector designs were tested in 6.35- and 8.9-cm-diameter flame tubes with non-vitiated heated air and gaseous hydrogen. Data is presented on measurements of NO(x) emissions and combustion efficiency for the hydrogen injectors at 2.540, 7.937, and 13.652 cm from the injector face. Results show that for some configurations, NO(x) emissions are comparable to that of state of the art Jet-A LDI combustor concepts.

Marek, C. John↗

Optimization of Saltcake Removal Flowsheet at SRS through Incorporation of Testing and In-Tank Waste Experience

Saltcake removal at SRS may be performed for several reasons: to provide space for evaporator operation (i.e., to precipitate more salt in the drop tank), to provide feed for salt processing (i.e. immobilize the waste), or to remove the salt for tank closure. Many different salt dissolution techniques have been employed in the 40 years that SRS has been performing salt removal, from a basic “Add, Sit, Remove” method (water is added on top of the saltcake and time is allowed for diffusion), to performing interstitial liquid removal, or using mixing devices to promote contact with the liquid. Lessons learned from previous saltcake removal campaigns, in addition to testing and modeling, have led to opportunities for improvements to the overall saltcake removal process. This includes better understanding of salt properties and behavior during dissolution; the primary concerns for salt dissolution are the release of radiolytic hydrogen and criticality prevention (post-dissolution). Recent developments in salt dissolution include the reuse of dilute supernate and a semi-continuous dissolution (SCD) process, where low volume mixing eductors are used to deliver water near the surface of the saltcake at the same rate as the salt solution is removed and transferred to a receipt tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CFD analysis of jet mixing in low NOx flametube combustors

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor was identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3-D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3-D CFD analyses for optimizing jet mixing was demonstrated.

Talpallikar, M. V.↗

Immersive Technologies for Human-in-the-Loop Lunar Surface Simulations

NASA, the National Aeronautics and Space Administration, continually seeks innovative solutions to enhance its operations, particularly in the realms of testing, evaluation, and training for future missions. Immersive technologies, such as virtual, augmented, and mixed reality have proven to be powerful tools for realistic, interactive, and engaging environments. This paper explores how the Simulation and Graphics Branch at NASA’s Johnson Space Center (JSC) leverages immersive technology, modern commercial rendering engines, and physics-based systems simulations to develop human-in-the-loop systems for humanity’s return to the Moon through the Artemis program. When NASA returns to the Moon, astronauts will travel to the Moon’s South Pole where lighting conditions will cause a more complex operational environment. Human-in-the-loop testing plays a crucial role in NASA's mission planning, spacecraft and space systems development, and evaluation of operational scenarios. The development of immersive environments such as a lunar rover mockup at a video wall enables engineers and astronauts to simulate and experience mission scenarios, integrated spacecraft systems, and operational procedures in a relevant environment before deployment. By integrating realistic virtual environments, immersive technology allows for the visualization and interaction with virtual spacecraft models, mission landscapes, and complex operational tasks. This approach helps identify potential design flaws, operational challenges, and safety considerations. It also provides valuable insights for risk reduction and helps improve mission efficiency and effectiveness. With advanced motion tracking systems and custom virtual environments data can be gathered and evaluated to help NASA refine training protocols, develop specialized training procedures and optimize human-robotic interactions for future space missions. Furthermore, immersive technology offers opportunities for future training initiatives at NASA. The Virtual Reality Laboratory at JSC has pioneered training with Virtual Reality (VR) since the Hubble Space Telescope repair missions in the early 1990’s. Extended Reality (XR) simulations enable astronauts to rehearse complex spacewalks, spacecraft maneuvers, and extravehicular activities in a safe and controlled environment. By replicating the physical and cognitive challenges of space missions, immersive training experiences enhance astronauts' situational awareness, decision-making abilities, and adaptability to unexpected scenarios. Additionally, immersive technology facilitates collaborative training, allowing geographically dispersed crew and mission control personnel to engage in synchronized simulations, fostering teamwork and effective communication. The adoption of immersive technology in NASA's testing, evaluation, and future training programs has yielded significant benefits. By incorporating human-in-the-loop testing for studies involving Extra Vehicular Activities (EVA), surface mobility and landing systems, NASA can identify and mitigate risks, optimize operational procedures, and enhance mission success. Ultimately, immersive training experiences can empower astronauts to better navigate the complexities of space missions, ensuring their safety, productivity, and success in the dynamic and challenging environments they will experience at the Lunar South Pole.

Simulation Modeling Virtual Reality Immersive Tech↗

SCM Paste Samples Exposed To Aggressive Solutions. Cementitious Barriers Partnership

This report summarizes experimental work performed by SIMCO Technologies Inc. (SIMCO) as part of the Cementitious Barriers Partnership (CBP) project. The test series followed an experimental program dedicated to the study of ordinary Portland cement (OPC) hydrated cement pastes exposed to aggressive solutions. In the present study, the scope is extended to hydrated cement pastes incorporating supplementary cementitious materials (SCM) such as fly ash and ground granulated blast furnace slag (GGBFS). Also, the range of aggressive contact solutions was expanded. The experimental program aimed at testing aggressive contact solutions that more closely mimic the chemical composition of saltstone pore solution. Five different solutions, some of which incorporated high levels of carbonate and nitrate, were placed in contact with four different hydrated cement paste mixes. In all solutions, 150 mmol/L of SO 4 2– (14 400 ppm) were present. The solutions included different pH conditions and different sodium content. Two paste mixes were equivalent to Vault 1/4 and Vault 2 concrete mixes used at SRS in storage structures. Two additional paste mixes, cast at the same water-to-cement ratio and using the same cements but without SCMs, were also tested. The damage evolution in samples was monitored using ultrasonic pulse velocity (UPV) and mass measurements. After three and twelve months of exposure conditions, samples were taken out of solution containers and analyzed to perform migration tests and porosity measurements. Globally, results were in line with the previous study and confirmed that high pH may limit the formation of some deleterious phases like gypsum. In this case, ettringite may form but is not necessarily associated with damage. However, the high concentration of sodium may be associated with the formation of an AFm-like mineral called U-phase. The most significant evidences of damage were all associated with the Vault 2 paste analog. This material proved very sensitive to high pH. All measurement techniques used to monitor and evaluate damage to samples indicated significant alterations to this mix when immersed in contact solutions containing sodium hydroxide. It was hypothesized that the low cement content, combined with high silica content coming from silica fume, fly ash and GGBFS led to the presence unreacted silica. It is possible that the pozzolanic reaction of these SCMs could not be activated due to the low alkali content, a direct consequence of low cement content. In this scenario, the material end up having a lot of silica available to react upon contact with sodium hydroxide, possibly forming a gel that may be similar to the gel formed in alkali-silica reactions. This scenario needs further experimental confirmation, but it may well explain the poor behavior of mix PV2 in presence of NaOH.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Reimagining Heating, Ventilation, and Air Conditioning for New Manufactured Homes

Manufactured homes represent one of the most affordable paths to home ownership for American households, but minimum-efficiency equipment and poor-quality home installation can lead to excess energy use and high operating costs. Slipstream, with partners from the Florida Solar Energy Center (FSEC), Northwest Energy Works, and Washington State University, identified and tested manufactured home HVAC innovations targeted for new construction offering the most promising mix of improved energy performance and likelihood of industry uptake.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation into Interfacial Mixing Behavior of Blown Powder Deposited Inconel 625-Copper Alloy Bimetallic for Improvement of Bimetallic Joint Strength

Use of laser blown powder, directed energy deposition (DED) provides a method for fabrication of bimetallic functional materials for high heat flux applications. However, this relatively new process currently has a low technology readiness level (TRL). Key to increasing the TRL is a better understanding of the factors that control mixing of the bi-metallic materials at the interface. The resulting interfaces in specimens obtained from three vendors were characterized using optical and electron microscopy with electron dispersion spectroscopy in addition to mechanical testing. Based on the range of process parameters and resulting interfaces, a model is being developed to predict interfacial mixing for development of specifications for improved and repeatable microstructures.

Additive Manufacturing↗

Combustion products generating and metering device

An apparatus for generating combustion products at a predetermined fixed rate, mixing the combustion products with air to achieve a given concentration, and distributing the resultant mixture to an area or device to be tested is described. The apparatus is comprised of blowers, a holder for the combustion product generating materials (which burn at a predictable and controlled rate), a mixing plenum chamber, and a means for distributing the air combustion product mixture.

Wiberg, R. E.↗

Final Report for the Testing of the Y-12 Criticality Accident Alarm System Detectors at the Godiva IV Burst Reactor (IER-443)

This report documents the experimental conditions and final results for the performance testing of the Y-12 Criticality Accident Alarm System (CAAS) detectors at the Godiva IV Burst Reactor at the National Criticality Experimental Research Center (NCERC) at the Nevada National Security Site (NNSS). The testing followed a previously issued test plan and was conducted during the week of July 17, 2017, with completion on Thursday July 20. The test subjected CAAS detectors supplied by Y-12 to very intense and short duration mixed neutron and gamma radiation fields to establish compliance to maximum radiation and minimum pulse width requirements. ANSI/ANS- 8.3.1997 states that the “system shall be sufficiently robust as to actuate an alarm signal when exposed to the maximum radiation expected”, which has been defined at Y-12, in Documented Safety Analyses (DSAs), to be a dose rate of 10 Rad/s. ANSI/ANS-8.3.1997 further states that “alarm actuation shall occur as a result of a minimum duration transient” which may be assumed to be 1 msec. The pulse widths and dose rates provided by each burst during the test exceeded those requirements. The CAAS detectors all provided an immediate alarm signal and remained operable after the bursts establishing compliance to the requirements and fitness for re-deployment at Y-12.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Method to calibrate fission chambers in Campbelling mode

Fission chambers are neutron detectors which are widely used to instrument experimental reactors such as material testing reactors or zero power reactors. In the presence of a high level mixed gamma and neutron flux, fission chambers can be operated in Campbelling mode (also known as 'fluctuation mode' or 'mean square voltage mode') to provide reliable and precise neutron related measurements. Fission chamber calibration in Campbelling mode (in terms of neutron flux) is usually done empirically using a calibrated reference detector. A major drawback of this method is that calibration measurements have to be performed in a neutron environment very similar to the one in which the calibrated detector will be used afterwards. What we propose here is a different approach based on characterizing the fission chamber response in terms of fission rate. This way, the detector calibration coefficient is independent from the neutron spectrum and can be determined prior to the experiment. The fissile deposit response to the neutron spectrum can then be assessed independently by other means (experimental or numerical). In this paper, the response of CEA made miniature fission chambers in Campbelling mode is studied. We use a theoretical model of the signal to calculate the calibration coefficient. Input parameters of the model come from statistical distribution of individual pulses. Supporting measurements have been made in the CEA Cadarache zero power reactor MINERVE and results are compared to an empirical Campbelling mode calibration. The tested fission chamber calibration coefficient is about 2 10{sup -26} A{sup 2}/Hz/(c/s). Both numerical and empirical methods give consistent results, however a deviation of about 15 % was observed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Method to calibrate fission chambers in Campbelling mode

Fission chambers are neutron detectors which are widely used to instrument experimental reactors such as material testing reactors or zero power reactors. In the presence of a high level mixed gamma and neutron flux, fission chambers can be operated in Campbelling mode (also known as 'fluctuation mode' or 'mean square voltage mode') to provide reliable and precise neutron related measurements. Fission chamber calibration in Campbelling mode (in terms of neutron flux) is usually done empirically using a calibrated reference detector. A major drawback of this method is that calibration measurements have to be performed in a neutron environment very similar to the one in which the calibrated detector will be used afterwards. What is proposed here is a different approach based on characterizing the fission chamber response in terms of fission rate. This way, the detector calibration coefficient is independent from the neutron spectrum and can be determined prior to the experiment. The fissile deposit response to the neutron spectrum can then be assessed independently by other means (experimental or numerical). In this paper, the response of CEA-made miniature fission chambers in Campbelling mode is studied. A theoretical model of the signal is used to calculate the calibration coefficient. The model's input parameters come from statistical distribution of individual pulses. Supporting measurements were made in the CEA Cadarache zero power reactor MINERVE and results are compared to an empirical Campbelling mode calibration. The tested fission chamber calibration coefficient is roughly 2*10{sup -26} A{sup 2}/Hz/(c/s). Both numerical and empirical methods give consistent results, however a deviation of about 15% was observed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effects of Testosterone on Mixed-Muscle Protein Synthesis and Proteome Dynamics During Energy Deficit

Effects of testosterone on integrated muscle protein metabolism and muscle mass during energy deficit are undetermined. The objective was to determine the effects of testosterone on mixed-muscle protein synthesis (MPS), proteome-wide fractional synthesis rates (FSR), and skeletal muscle mass during energy deficit. This was a randomized, double-blind, placebo-controlled trial. The study was conducted at Pennington Biomedical Research Center. Fifty healthy men. The study consisted of 14 days of weight maintenance, followed by a 28-day 55% energy deficit with 200 mg testosterone enanthate (TEST, n = 24) or placebo (PLA, n = 26) weekly, and up to 42 days of ad libitum recovery feeding. Mixed-MPS and proteome-wide FSR before (Pre), during (Mid), and after (Post) the energy deficit were determined using heavy water (days 1-42) and muscle biopsies. Muscle mass was determined using the D3-creatine dilution method. Mixed-MPS was lower than Pre at Mid and Post (P < 0.0005), with no difference between TEST and PLA. The proportion of individual proteins with numerically higher FSR in TEST than PLA was significant by 2-tailed binomial test at Post (52/67; P < 0.05), but not Mid (32/67; P > 0.05). Muscle mass was unchanged during energy deficit but was greater in TEST than PLA during recovery (P < 0.05). The high proportion of individual proteins with greater FSR in TEST than PLA at Post suggests exogenous testosterone exerted a delayed but broad stimulatory effect on synthesis rates across the muscle proteome during energy deficit, resulting in muscle mass accretion during subsequent recovery.

Endocrinology & Metabolism↗

An Interim Set of TNT Curves for LOX/LNG Explosions

Space launch companies are actively developing, or in some cases have already developed, new vehicles that use large quantities of liquid oxygen (LOX) and liquid natural gas (LNG) propellants. This propellant mixture currently lacks sound/verified explosive safety standards for use in explosive siting and flight safety analysis. In the U.S., multiple government and commercial organizations have conducted limited testing, or are preparing to conduct tests, intended to provide a sound technical basis for LOX/LNG explosive standards applicable to space launch vehicle ground and flight operations. The limited testing and analysis conducted so far indicates the potential to produce extremely energetic explosions due to the miscibility of LOX/LNG (methane), a unique feature relative to previously used propellant mixtures such as hydrogen/oxygen or kerosene/oxygen. MOX is a homogenous mixture of methane and oxygen that is possible because of methane’s 100% miscibility in LOX. Preliminary testing by N2L, Inc. described in this paper shows that it is possible to form MOX with a variety of mixing methods, and that MOX is a sensitive high explosive capable of producing overpressures greater than comparable masses of C-4. The limited amount and quality of large-scale LOX/LNG explosive test data, and the potential formation of high-explosive MOX, create significant unknowns in the determination of hazard areas (cleared of the public) for ground operations (such as a static fire test) and flights of launch vehicles with LOX/LNG propellant. This paper will review the methods used by NASA to develop and validate the LOX/LH2 blast model using large-scale explosive test programs such as Project PYRO, the Hydrogen-Oxygen Vertical Impact (HOVI), and the Large-Scale Hydrogen-Oxygen Explosion (LSHOE) tests. This paper will describe how the same process was used to prepare an interim LOX/LNG blast model that applies to various LV failure scenarios and conservatively accounts for potential MOX formation. This paper also summarizes past and future testing and modeling efforts funded by a consortium of NASA, the US Federal Aviation Administration (FAA), and the US Space Force (USSF). These test programs should be concluded within the next 3 years and are intended to provide empirical data for model verification and validation.

Liquid Oxygen↗

An Interim Set of TNT Curves for LOX/LNG Explosions

Space launch companies are actively developing, or in some cases have already developed, new vehicles that use large quantities of liquid oxygen (LOX) and liquid natural gas (LNG) propellants. This propellant mixture currently lacks sound/verified LOX/LNG explosive safety standards for use in explosive siting and flight safety analysis. In the U.S., multiple government and commercial organizations have conducted limited testing, or are preparing to conduct tests, intended to provide a sound technical basis for explosive standards applicable to space launch vehicle ground and flight operations. The limited testing and analysis conducted so far indicates the potential to produce extremely energetic explosions due to the miscibility of LOX/LNG (methane), a unique feature relative to previously used propellant mixtures such as hydrogen/oxygen or kerosene/oxygen. MOX is a homogenous mixture of methane and oxygen that is possible because of methane’s 100% miscibility in LOX. Preliminary testing by N2L, Inc. described in this paper shows that it is possible to form MOX with a variety of mixing methods, and that MOX is a sensitive high explosive capable of producing overpressures greater than comparable masses of C-4. The limited amount and quality of large-scale LOX/LNG explosive test data, and the potential formation of high-explosive MOX, create significant unknowns in the determination of hazard areas (cleared of the public) for ground operations (such as a static fire test) and flights of launch vehicles with LOX/LNG propellant. This paper will review the methods used by NASA to develop and validate the LOX/LH2 blast model using large-scale explosive test programs such as Project PYRO, the Hydrogen-Oxygen Vertical Impact (HOVI), and the Large-Scale Hydrogen-Oxygen Explosion (LSHOE) tests. This paper will describe how the same process was used to prepare an interim LOX/LNG blast model that applies to various LV failure scenarios and conservatively accounts for potential MOX formation. This paper also summarizes past and future testing and modeling efforts funded by a consortium of NASA, the US Federal Aviation Administration (FAA), and the US Space Force (USSF). These test programs should be concluded within the next 3 years and are intended to provide empirical data for model verification and validation.

Liquid Oxygen↗

CFD analysis of jet mixing in low NO(x) flametube combustors

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor has been identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3D CFD analyses for optimizing jet mixing was demonstrated.

Talpallikar, M. V.↗

Final Design for Thermal/Epithermal eXperiments using High 240 Pu Content Plutonium/Aluminum Zero Power Research Reactor Plates with Polyethylene Moderator (IER 520 Final Design CED-2 Report)

The US Department of Energy Nuclear Criticality Safety Program (NCSP) convened a multinational Thermal Epithermal eXperiments (TEX) meeting in July of 2011 to discuss the data and experimental needs of criticality safety practitioners. The number one and two priority integral experiment data needs were for 239 Pu and 240 Pu, with special emphasis on cross section performance in the intermediate energy range (from 0.625 eV to 100 keV). LLNL measured five critical configurations with LANL for the plutonium test bed (IER-184) and published the experiments as International Criticality Safety Benchmark Evaluation Project evaluation PUMET-MIXED-002. Modeling of the benchmark configurations using ENDF/B-VIII.0 nuclear data showed significant overprediction of reactivity for configurations that had a large percentage of fissions in the intermediate energy regime. This report documents a variation on the TEX plutonium test bed to provide a test of 240 Pu cross sections, with sensitivity of the configuration to 240 Pu radiative capture and fission cross sections a priority for the design.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A multispecies turbulence model for the mixing and de-mixing of miscible fluids

A de-mix capable model for turbulence in compressible, variable density flows is proposed. The model is based on the Besnard-Harlow-Rauenzahn (BHR) family of models (Besnard D, Harlow F, Rauenzahn R, et al. Turbulence transport equations for variable-density turbulence and their relationship to two-field models. NM (United States): Los Alamos National Laboratory; 1992 (Technical Report LA-12303-MS), but is extended to track the evolution of the turbulent fluxes and fluctuations in the material mass fractions for each species present. The new evolution equations are introduced without requiring additional closures or new empirically tuned coefficients relative to previous BHR models, and are shown to improve the model’s ability to reproduce the behaviour of simulations containing mixing layers that are constrained by a stabilising force. As a result, the model is tested in a range of canonical flows including Rayleigh-Taylor driven, shock driven, and shear driven turbulence, and is shown to produce reasonable agreement with simulations and experiments in these scenarios.

42 ENGINEERING↗

Aging Hanford Nuclear Waste Using Carbon Dioxide to Evaluate Corrosion at Lower pH Limits - 18467

Samples of Hanford Nuclear Reservation (HNR) tank waste and simulated Hanford tank waste were exposed to carbon dioxide gas (CO{sub 2}) in the laboratory in order to decrease the pH of the solution. Sodium hydroxide is required to be added to some tanks according to waste handling specifications to keep tanks protected from pitting corrosion, but the maximum-allowed volume in some tanks is currently approaching capacity. Decreasing the pH of tank solutions using CO{sub 2} gas mimics the environmental exposure chemistry, does not add sodium, and allows for testing on solutions currently categorized as out-of-specification according to technical waste handling documents. Legacy alloy A537 Class 1 carbon steel was used to construct the AN tanks on the HNR and was utilized for this testing. The planned testing of three solutions included a simulant for feasibility and a waste solution from Tank 241-AN-102 (AN-102), taken in 2013, which was run in duplicate. The solutions were evaluated for corrosion potential using cyclic potentiodynamic polarization (CPP) scans to determine the propensity for stress corrosion cracking and pitting corrosion. Results in all solutions showed that pitting potential was low when the pH was above 11 and temperatures were below 40 deg. C. As solution pHs dipped into the 10- 10.5 range, there were mixed results. CPP scans were initially run at the higher temperature of 50 deg. C, accelerating corrosion rates. Solution pHs that did not indicate corrosion were further exposed to CO{sub 2}. Solutions with mixed or positive pitting results were rerun at 40 deg. C. The first failed run on the tank solution was seen when testing the duplicate sample at 50 deg. C and a pH of 13.01. When this solution was retested at 40 deg. C, the CPP scan did not show corrosion. A mixed corrosion result was obtained from a scan run at the final pH of 10 when tested at 50 deg. C. Upon completion of testing a visual inspection of the coupon did not show corrosion products on its surface. These results provide assurance that tanks containing slightly reduced pHs are still protected from pitting corrosion. Tank integrity assurance at a lower pH limit in Tank AN-102 could slow sodium addition and the rising volume of hazardous waste. Other benefits of reducing the pH specification would be reduced costs associated with retrieving and storing smaller volumes of hazardous waste, a reduced number of radiation exposure events (required for pH modification of tank waste), and a potential for a decreased volume required to be immobilized for long-term storage in a vitrified (glass) phase. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗