Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Single-crystal X-ray diffraction of fluorapatite to 61 GPa

Apatite is a mineral of widespread importance in Earth and planetary science. Here we examine the behavior of a natural fluorapatite (FAp) crystal from Durango (Mexico) under compression to 61 GPa. Single-crystal X-ray diffraction experiments were carried out in a diamond-anvil cell using a synchrotron source. The apatite structure persists up to 32.4 GPa. Birch-Murnaghan equation of state parameters were fit to the pressure-volume data for fluorapatite for two cases: fixing V 0 at its measured ambient value resulted in a bulk modulus, K 0T , of 97.0(8) GPa and a pressure derivative of the bulk modulus, K' 0T , of 3.3(1), while fixing V 0 and K 0T at its ambient value 90.5 GPa (derived from ultrasonically measured elastic constants) resulted in a K' 0T value of 4.1(1). At 35.6 GPa, fluorapatite transforms to a triclinic phase (P$\bar{1}$, Z = 4), designated here as fluorapatite II (FAp-II). This phase persists up to at least 61 GPa. The major structural differences between FAp and FAp-II involve the buckling of the Ca polyhedra along the c-axis and changes in the number and coordination of the Ca sites. Furthermore, our study extends the pressure range over which fluorapatite has been examined by more than a factor of three, providing new insights into its structural response to high-pressure conditions.

58 GEOSCIENCES↗

High-Pressure Study on Lead Fluorapatite

The compressional behavior of a synthetic lead fluorapatite [Pb9.35(PO4)6F2] has been investigated in situ up to about 16.7 GPa at 300 K, using a diamond-anvil cell and synchrotron X-ray diffraction. We find that the compressibility of lead fluorapatite is significantly different from that of fluorapatite [Ca10(PO4)6F2], chlorapatite [Ca10(PO4)6Cl2], and hydroxylapatite [Ca10(PO4)6(OH)2]: lead fluorapatite is much more compressible, and elastically isotropic in the investigated pressure range. The pressure-volume data fitted to the third-order Birch-Murnaghan equation yield an isothermal bulk modulus (KT) of 54.3(18) GPa and the pressure derivative (KT') of 8.1(6). If KT' is fixed at 4, the obtained KT is 68.4(16) GPa, which is approximately only two-thirds of the isothermal bulk modulus of the calcium apatites.

43 PARTICLE ACCELERATORS↗

The high-pressure-high-temperature behavior of bassanite

The pressure evolution of bassanite (CaSO{sub 4} {center_dot} 1/2 H{sub 2}O) was investigated by synchrotron X-ray powder diffraction along three isotherms: at room temperature up to 33 GPa, at 109 C up to 22 GPa, and at 200 C up to 12 GPa. The room-temperature cell-volume data, from 0.001 to 33 GPa, were fitted to a third-order Birch-Murnaghan equation-of-state, and a bulk modulus K{sub 0} = 86(7) GPa with K' = 2.5(3) was obtained. The axial compressibility values are {beta}{sub a} = 3.7(2), {beta}{sub b} = 3.6(1), and {beta}{sub c} = 2.8(1) GPa{sup -1} (x10{sup -3}) showing a slightly anisotropic behavior, with the least compressible direction along c axis. The strain tensor analysis shows that the main deformation occurs in the (010) plane in a direction 18{sup o} from the a axis. The bulk moduli for isotherms 109 and 200 C, were obtained by fitting cell-volume data with a second-order Birch-Murnaghan equation-of-state, with K' fixed at 4, and were found to be K{sub 109} = 79(4) GPa and K{sub 200} = 63(7) GPa, respectively. The axial compressibility values for isotherm 109 C are {beta}{sub a} = 2.4(1), {beta}{sub b} = 3.0(1), {beta}{sub c} = 2.5(1) (x10{sup -3}) GPa{sup -1}, and for isotherm 200 C they are {beta}{sub a} = 3.5(3), {beta}{sub b} = 3.4(3), {beta}{sub c} = 2.6(4) (x10{sup -3}) GPa{sup -1}. These two bulk moduli and the 20 C bulk modulus, K{sub 0,20} = 69(8) recalculated to a second-order Birch-Murnaghan EoS to be consistent, as well as the axial compressibilities, are similar for the three isotherms indicating that the thermal effect on the bulk moduli is not significant up to 200 C. The size variation of the pseudo-hexagonal channel with pressure and temperature indicates that the sulfate 'host' lattice and the H{sub 2}O 'guest' molecule in bassanite do not undergo strong change up to 33 GPa and 200 C.

58 GEOSCIENCES↗

Effect of Hydration on the Single-crystal Elasticity of Fe-bearing Wadsleyite to 12 GPa

The single-crystal elastic properties of Fe-bearing wadsleyite with 1.93 wt% H{sub 2}O (Mg{sub 1.634}Fe{sub 0.202}H{sub 0.305}SiO{sub 4}) have been determined by Brillouin scattering. At ambient conditions, the aggregate bulk and shear moduli (K{sub S0}, G{sub 0}) of this wadsleyite are 156.2(5) and 98.0(3) GPa, respectively. Compared to the corresponding anhydrous wadsleyite, 1.93 wt% H{sub 2}O lowers K{sub S0} and G{sub 0} by 8.1% and 9.3%, respectively. High-pressure measurements up to 12 GPa show that the pressure derivative of the bulk modulus, K'{sub S0} = 4.8(1), is similar to that of the anhydrous Fe-wadsleyite with reported values of 4.6-4.74, but the addition of H{sub 2}O increases the pressure derivative of the shear modulus, G{sub 0}' from 1.5(1) to 1.9(1). This contrasts with the G{sub 0}' of Fe-free wadsleyite, which is the same within uncertainty for the hydrous and anhydrous phases. As a result, both the compressional- and shear-wave velocities (v{sub P}, v{sub S}) of hydrous Fe-bearing wadsleyite are about 200({+-}24) m/s slower than anhydrous Fe-bearing wadsleyite at transition zone pressures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Operational and Compositional Factors that Affect the Performance Properties of ARP/MCU Saltstone Grout

The Saltstone Production Facility (SPF) receives low level waste (LLW) salt solution from Tank 50H for treatment and disposal. Tank 50H receives transfers from the Effluent Treatment Project (ETP), the H-Canyon General Purpose Evaporator, and the Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU) Decontaminated Salt Solution Hold Tank (DSS-HT). At the SPF, the LLW is mixed with premix (a cementitious mixture of portland cement (PC), blast furnace slag (BFS) and Class F fly ash (FA)) in a Readco mixer to produce fresh (uncured) saltstone that is transferred to the Saltstone Disposal Facility (SDF) vaults. The saltstone formulation (mix design) must produce a grout waste form that meets both placement and performance properties. In previous simulated saltstone studies, multiple compositional factors were identified that drive the performance properties of saltstone made from the projected ARP/MCU salt solution. This composition was selected as salt solution simulant since ARP/MCU is the primary influent into Tank 50H. The primary performance property investigated was hydraulic conductivity since it is a variable input property to the saltstone Performance Assessment (PA) transport model. In addition, the porosity, also referred to as void structure, is another variable that impacts the PA response. In addition, Young's modulus and cured density are other performance properties analyzed in this report; however they are indicators of the performance of saltstone and not direct inputs into the PA. The data from previous studies showed that the largest impact on the performance properties of saltstone was due to curing temperature, followed by aluminate concentration in the salt solution, water to premix ratio and premix composition. However, due to the scope of the previous studies, only a few mixes were cured and analyzed at higher temperatures. The samples cured at 60°C had an increased hydraulic conductivity of approximately 600 times that of the sample cured at room temperature. The hydration reactions initiated during the mixing of the premix and salt solution continue during the curing period in the vaults to produce the hardened waste form product. The heat generated from exothermic hydration reactions results in a temperature increase in the vaults that depends on the composition of the decontaminated salt solution being dispositioned, the grout formulation (mix design) and the pour frequency and volume. This heat generation is a contributing factor to the temperature increase in the vaults that leads to an increased cure temperature for the grout. This report will further investigate the impact of curing temperature on saltstone performance properties (hydraulic conductivity, Young's modulus, porosity, etc.) over a range of aluminate concentration, water to premix (w/p) ratio and weight percent fly ash in the premix processed at the SPF. The three curing temperatures selected for this study were chosen to provide data at fixed cure temperatures that represent measured temperatures in the SDF vaults. This does not represent the conditions in the vault where the temperature of the saltstone is continually changing with time. For example, it may take several days for the saltstone to reach 60°C at a given elevation. Previous results demonstrated that the rates at which a selected curing temperature is reached affect the performance properties. The approach taken in this task, a rapid increase to the curing temperature, may be conservative with respect to decreased performance. Nevertheless, the data will provide a basis from which to determine the impact of curing temperature on saltstone performance as a function of key variables. A statistical evaluation of the results for these mixes will be performed to provide the range, and associated uncertainties, of hydraulic conductivity and other properties over this factor space.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Low Velocity Sphere Impact of a Borosilicate Glass

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Borofloat borosilicate glass, and is a follow-up to a similar study completed by the authors on Starphire soda-lime silicate glass last year. The response of the borosilicate glass to impact testing at different angles was also studied. The Borofloat glass was supplied by the US Army Research Laboratory and its tin-side was impacted or indented. The intent was to better understand low velocity impact response in the Borofloat. Seven sphere materials were used whose densities bracket that of rock: borosilicate glass, soda-lime silicate glass, silicon nitride, aluminum oxide, zirconium oxide, carbon steel, and a chrome steel. A gas gun or a ball-drop test setup was used to produce controlled velocity delivery of the spheres against the glass tile targets. Minimum impact velocities to initiate fracture in the Borofloat were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the seven sphere-Borofloat-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) BS glass responded similarly to soda-lime silicate glass when spherically indented but quite differently under sphere impact conditions; (2) Frictional effects contributed to fracture initiation in BS glass when it spherically indented. This effect was also observed with soda-lime silicate glass; (3) The force necessary to initiate fracture in BS glass under spherical impact decreases with increasing elastic modulus of the sphere material. This trend is opposite to what was observed with soda-lime silicate glass. Friction cannot explain this trend and the authors do not have a legitimate explanation for it yet; (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than under quasi-static conditions. That difference decreases with increasing elastic modulus mismatch between the sphere material and borosilicate This trend was opposite in soda-lime silicate glass; (5) Fracture in borosilicate glass occurs at lower velocities (i.e., easier) at 24° than at 0° (orthogonal) and 46° of impact for the same probability of failure. Though not analyzed yet, this suggests that a convolution of kinetic energy and friction is contributing to that trend; (6) There is a subtle indication there was intra-tile differences in spherical indentation RCIF. This likely is not a material property nor exclusive to borosilicate glass, rather, it is a statistical response of a combination of local, surface-located flaw and imposed tensile stress. Understanding of the surface flaw population and flaw positioning can likely enable prediction of spherical indentation RCIF; and (7) Contact-induced fracture did not initiate in the Borofloat BS for impact kinetic energies up to ~ 20 mJ. For kinetic energies between ~ 20-150 mJ, fracture sometimes initiated. Contact-induced fracture would always occur for impact energies > 150 mJ. The energy values, and their boundaries, were much lower for BS glass than they were for soda-lime silicate glass.

36 MATERIALS SCIENCE↗

Properties of Bulk Sintered Silver As a Function of Porosity

This report summarizes a study where various properties of bulk-sintered silver were investigated over a range of porosity. This work was conducted within the National Transportation Research Center's Power Device Packaging project that is part of the DOE Vehicle Technologies Advanced Power Electronics and Electric Motors Program. Sintered silver, as an interconnect material in power electronics, inherently has porosity in its produced structure because of the way it is made. Therefore, interest existed in this study to examine if that porosity affected electrical properties, thermal properties, and mechanical properties because any dependencies could affect the intended function (e.g., thermal transfer, mechanical stress relief, etc.) or reliability of that interconnect layer and alter how its performance is modeled. Disks of bulk-sintered silver were fabricated using different starting silver pastes and different sintering conditions to promote different amounts of porosity. Test coupons were harvested out of the disks to measure electrical resistivity and electrical conductivity, thermal conductivity, coefficient of thermal expansion, elastic modulus, Poisson's ratio, and yield stress. The authors fully recognize that the microstructure of processed bulk silver coupons may indeed not be identical to the microstructure produced in thin (20-50 microns) layers of sintered silver. However, measuring these same properties with such a thin actual structure is very difficult, requires very specialized specimen preparation and unique testing instrumentation, is expensive, and has experimental shortfalls of its own, so the authors concluded that the herein measured responses using processed bulk sintered silver coupons would be sufficient to determine acceptable values of those properties. Almost all the investigated properties of bulk sintered silver changed with porosity content within a range of 3-38% porosity. Electrical resistivity, electrical conductivity, thermal conductivity, elastic modulus, Poisson's ratio, and yield stress all depended on the porosity content in bulk-sintered silver. The only investigated property that was independent of porosity in that range was coefficient of thermal expansion.

36 MATERIALS SCIENCE↗

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan™-G1 and SCHOTT Resistan™-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire® soda-lime silicate glass and SCHOTT BOROFLOAT® borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si 3 N 4 ) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan™-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire® soda-lime silicate glass was second best, then Resistan™-G1 glass ceramic, and then BOROFLOAT® borosilicate glass. (2) Glass-ceramic Resistan™-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire® soda-lime silicate glass, Resistan™-G1 glass ceramic, and BOROFLOAT® borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan™-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan™-G1. Friction also affected ring crack initiation in Starphire® soda-lime silicate and BOROFLOAT® borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire® and least pronounced in the BOROFLOAT®. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan™-L and Resistan™-G1 glass ceramics. This is a trend observed too in Starphire® and BOROFLOAT®. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan™-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

36 MATERIALS SCIENCE↗

Experimental Plan for EDF Energy Creep Rabbit Graphite Irradiations- Rev. 2 (replaces Rev. 0 ORNL/TM/2013/49)

The experimental results obtained here will assist in the development and validation of future models of irradiation induced creep of graphite by providing the following data: Inert creep stain data from low to lifetime AGR fluence Inert creep-property data (especially CTE) from low to lifetime AGR fluence Effect of oxidation on creep modulus (by indirect comparison with experiment 1 and direct comparison with experiment 3 NB. Experiment 1 and 3 are not covered here) Data to develop a mechanistic understanding, including: appropriate creep modulus (including pinning and high dose effects on structure), investigation of CTE-creep strain behavior under inert conditions oInformation on the effect of applied stress/creep strain on crystallite orientation (requires XRD), effect of creep strain on micro-porosity (requires tomography & microscopy) This document describes the experimental work planned to meet the requirements of project technical specification and EDF Energy requests for additional Pre-IE work. The PIE work is described in detail in this revision (Section 8 and 9).

Burchell, Timothy D.↗

Radiation behavior of high-entropy alloys for advanced reactors. Final report

In the first task, we have demonstrated the radiation damage and the recrystallization behaviors in multicomponent alloys through molecular-dynamics simulations. It is found that by alloying with atoms of different sizes, the atomic-level strain increases, and the propensity of the radiation-induced crystalline to amorphous transition increases as the defects cluster in the cascade body. Recrystallization of the radiation induced supercooled or glass regions show that by tuning the composition and the equilibrium temperature, the multicomponent alloys can be healed. The crystalline-amorphous-crystalline transitions predict the potential high radiation resistance in multicomponent alloys. In the second task, three types of high-entropy alloys (HEAs) were fabricated from AlCoCrFeNi and AlCuCrFeNi quinary alloys. Hardness and reduced contact modulus were measured using nanoindentation tests. Heavy ion irradiation were performed using 10 MeV gold and 5 MeV nickel to study radiation effects. Al 0.5 CrCuFeNi 2 shows phase separation upon the presence of copper. Both hardness and contact modulus exhibit the same trend as increasing the applied load, and it indicates that excessive free volume may alter the growth rate of the plastic zone. The as-cast Al 0.1 CoCrFeNi specimen undergone the hot isostatic pressing (HIP) process and steady cooling rate which mitigate the quenching effect. The swelling behavior was characterized by the atomic force microscopy (AFM), and the swelling rate is approximately 0.02% dpa. Selected area diffraction (SAD) patters show irradiation-induced amorphization throughout the ion projected range. Within the peak damage region, an amorpous ring is observed, and a mixture of amorphous/ crystalline structure at deeper depth is found. The Al 0.3 CoCrFeNi HEAs shows good radiation resistance up to 60 peak dpa. No voids or dislocations are observed. The crystal structures remain face-centered-cubic (FCC) before and after 5 MeV Ni irradiation. Higher dpa might be required to study defects formation mechanisms. In the third task, all the constituent binary and ternary systems of the Al-Co-Cr-Fe-Ni system were thermodynamically modeled within the whole composition range. Comparisons between the calculated phase diagrams and literature data are in good agreement. The multi-component thermodynamic database of the Al-Co-Cr-Fe-Ni system was then obtained via extrapolation. The current Al-Co-Cr-Fe-Ni thermodynamic database enables us to carry out the calculations of phase diagrams, which can be used as useful guidelines to identify the Al-Co-Cr-Fe-Ni HEAs with desirable microstructures. In the fourth task, we discuss how as-cast and homogenized phases can be identified, what phases are usually found in the as-cast and homogenized conditions, and what the thermodynamics and kinetics of phase transformations are in the AlCoCrFeNi HEA. The microstructure and phase composition were studied in as-cast and homogenized conditions. It showed the dendritrical structure in the as-cast condition consisting primarily of a nano-lamellar mixture of A2 [disorder body-centered-cubic (BCC)] and B2 (ordered BCC) phases, in addition to a very small amount of A1 [disorder face-centered-cubic (FCC)] phases. The homogenization heat treatment resulted in an increase in the volume fraction of the A1 phase and formation of a Sigma phase. Tensile properties in as-cast and homogenized conditions are reported at 700 °C. Thermodynamic modeling of non-equilibrium and equilibrium phase diagrams for the AlCoCrFeNi HEA gave good agreement with the experimental observations of the phase contents. The reasons for the improvement of ductility after the heat treatment are discussed.

36 MATERIALS SCIENCE↗

Molecular Dynamics Modeling of PPTA Crystals in Aramid Fibers

In this work, molecular dynamics modeling is used to study the mechanical properties of PPTA crystallites, which are the fundamental microstructural building blocks of polymer aramid bers such as Kevlar. Particular focus is given to constant strain rate axial loading simulations of PPTA crystallites, which is motivated by the rate-dependent mechanical properties observed in some experiments with aramid bers. In order to accommodate the covalent bond rupture that occurs in loading a crystallite to failure, the reactive bond order force eld ReaxFF is employed to conduct the simulations. Two major topics are addressed: The rst is the general behavior of PPTA crystallites under strain rate loading. Constant strain rate loading simulations of crystalline PPTA reveal that the crystal failure strain increases with increasing strain rate, while the modulus is not a ected by the strain rate. Increasing temperature lowers both the modulus and the failure strain. The simulations also identify the C N bond connecting the aromatic rings as weakest primary bond along the backbone of the PPTA chain. The e ect of chain-end defects on PPTA micromechanics is explored, and it is found that the presence of a chain-end defect transfers load to the adjacent chains in the hydrogen-bonded sheet in which the defect resides, but does not in uence the behavior of any other chains in the crystal. Chain-end defects are found to lower the strength of the crystal when clustered together, inducing bond failure via stress concentrations arising from the load transfer to bonds in adjacent chains near the defect site. The second topic addressed is the nature of primary and secondary bond failure in crystalline PPTA. Failure of both types of bonds is found to be stochastic in nature and driven by thermal uctuations of the bonds within the crystal. A model is proposed which uses reliability theory to model bonds under constant strain rate loading as components with time-dependent failure rate functions. The model is shown to work well for predicting the onset of primary backbone bond failure, as well as the onset of secondary bond failure via chain slippage for the case of isolated non-interacting chain-end defects.

36 MATERIALS SCIENCE↗

Foamed Cement Interactions with CO 2

Geologic carbon storage (GCS) is a potentially viable strategy to reduce greenhouse emissions. Understanding the risks to engineered and geologic structures associated with GCS is an important first step towards developing practices for safe and effective storage. The widespread utilization of foamed cement in wells may mean that carbon dioxide (CO 2 )/brine/foamed cement reactions may occur within these GCS sites. Characterizing the difference in alteration rates as well as the physical and mechanical impact of CO 2 /brine/foamed cement is an important preliminary step to ensuring offshore and onshore GCS is a prudent anthropogenic CO 2 mitigation choice. In a typical oil and gas well, cement is placed in the annulus between the steel casing and formation rock for both zonal isolation and casing support. The cement must have sufficient strength to secure the casing in the hole and withstand the stress of drilling, perforating, and fracturing (e.g. API, 1997, 2010 Worldwide Cementing Practices). As such, measuring the mechanical and properties of cement is an important step in predicting cement behavior under applied downhole stresses (Nelson, 2006). Zonal isolation is the prevention of fluids migrating to different zones outside of the casing and is strongly impacted by the permeability of the wellbore cement (Nelson, 2006). Zonal isolation depends on both the mechanical behavior and permeability (a physical property) of the cement (Mueller and Eid, 2006; Nelson, 2006). Long-term integrity of cement depends on the mechanical properties of the cement sheath, such as Young’s Modulus (Griffith et al., 2004). The cement sheath’s ability to withstand the stresses from changes in pressure and temperature is predominantly determined by the mechanical properties, including Young’s modulus, Poisson’s ratio, and tensile strength. Any geochemical alteration may impact both the mechanical and physical properties of the cement, thus ultimately impacting the structural integrity of the wellbore. In this study, atmospheric foamed cements were generated using a neat cement and three foam qualities (volume of entrained gas in the cement) - 10%, 20%, and 30 % gas volume. The samples were immersed in a 0.25 M NaCl brine followed by the injection of supercritical CO 2 at 28.9 MPa and 50°C. Petrophysical properties were examined for representative samples using computed tomography (CT) and scanning electron microscopy (SEM). CT scanning of representative samples across the range of reacted cements revealed macroscopic changes in structure due to brine/CO 2 /cement interactions. The high foam quality samples resulted in more CO 2 -saturated brine infiltrating radially deeper into the cement and thus were more susceptible to alteration. After 56 days of exposure, the 30% foam quality sample had the most reaction resulting in an alteration depth of 8.35 ± 0.13 mm with a calculated 34.6 ± 0.2% reacted area and 5.76 ± 0.2% reacted pore space area. The neat sample on the other hand, had a reaction depth of 0.31 ± 0.13 mm with a calculated 0.15 ± 0.08% reacted area and 0.57 ± 0.05% reacted pore area. Physical measurements of the exposed samples were consistent with this degree of alteration having 47.02% porosity and the highest permeability of 0.041 mD. These results indicate that the greater surface area provided by the increase of pore space in the higher quality foam coupled with carbonate diffusion reactions enabled greater alteration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Role of contamination on the bondline integrity of composite structures

Adhesively bonding composite structures have many applications in aerospace, automotive and submarine industries. The adhesive bonding joints have substantial advantage over the traditional metallic mechanical bonding joints, such as rivet and welding. However, the adhesive bonding joints require additional steps of surface preparation and cleaning to ensure consistent bond strength. In application, the adhesively bonded joints are exposed to environmental degradation and industrial solvent contaminates. Accordingly, the assurance of reliability of bonded composite structures requires detailed investigation of the role of contaminates on bondline integrity. This dissertation focuses on assessing the contaminates effect on the adhesive bondline integrity. A combined experimental and numerical framework is developed to study the contamination effect on the adhesive mechanical properties and adhesive joint strength. The bondline integrity were examined for a system of adhesive (EA9394) and the carbonfiber system (Hexply IM7/8552), after being subjected to different level of exposures to aviation hydraulic fluids and mold cleaning agents. A testing protocol based on nanoindentation for initial screening is used to predict the interfacial fracture characteristics after exposure to contamination. It is found the adhesive modulus and stiffness dropped by up to 10% for the hydraulic fluid contaminates, suggesting increase of the plastic dissipation within the bondline. However, the trend for the cleaning agent was not clear since the modulus drop while its hardness increased.

36 MATERIALS SCIENCE↗

Pressurized Slot Testing to Determine Thermo-Mechanical Properties of Lithophysal Tuff at Yucca Mountain Nevada.

The study described in this report involves heated and unheated pressurized slot testing to determine thermo-mechanical properties of the Tptpll (Tertiary, Paintbrush, Topopah Spring Tuff Formation, crystal poor, lower lithophysal) and Tptpul (upper lithophysal) lithostratigraphic units at Yucca Mountain, Nevada. A large volume fraction of the proposed repository at Yucca Mountain may reside in the Tptpll lithostratigraphic unit. This unit is characterized by voids, or lithophysae, which range in size from centimeters to meters, making a field program an effective method of measuring bulk thermal-mechanical rock properties (thermal expansion, rock mass modulus, compressive strength, time-dependent deformation) over a range of temperature and rock conditions. The field tests outlined in this report provide data for the determination of thermo-mechanical properties of this unit. Rock-mass response data collected during this field test will reduce the uncertainty in key thermal-mechanical modeling parameters (rock-mass modulus, strength and thermal expansion) for the Tptpll lithostratigraphic unit, and provide a basis for understanding thermal-mechanical behavior of this unit. The measurements will be used to evaluate numerical models of the thermal-mechanical response of the repository. These numerical models are then used to predict pre- and post-closure repository response. ACKNOWLEDGEMENTS The authors would like to thank David Bronowski, Ronnie Taylor, Ray E. Finley, Cliff Howard, Michael Schuhen (all SNL) and Fred Homuth (LANL) for their work in the planning and implementation of the tests described in this report. This is a reprint of SAND2004-2703, which was originally printed in July 2004. At that time, it was printed for a restricted audience. It has now been approved for unlimited release.

36 MATERIALS SCIENCE↗

Creep Analysis of Poly(ester urethane) Copolymer by Dynamic Mechanical Analysis (DMA): Melt Determination

An experiment is presented utilizing film tension, creep test dynamic mechanical analysis (DMA) to characterize the physical properties of a poly(ester urethane) block copolymer, Estane ® 5703. The polymer was pressed into a sheet from pellet form and cut into strips for analysis utilizing the TA Q800 DMA with film tension clamp. The strips were tested under five constant stress analyses from 0.125 to 0.625, at 0.125 MPa increments. Each analysis was run stepwise through a temperature gradient from 25 °C to 67 .5 °C with 2.5 °C increments, the material reached the instrument maximum displacement at different temperature steps dependent on the constant applied stress. At each of the 18 temperature steps the material was held at constant stress for 10 minutes and allowed to recover under stress-less conditions for 20 minutes. With data analysis recoverable strain data was produced and ultimately a curve of Modulus at temperature, the regression extrapolated to modulus = 0 M Pa. The extrapolated point correlated with data the weighted average melt point of the polymer measured by MDSC, within the regressive least squares fit of the measured moduli. Thereby measuring the melt temperature of a polymer by DMA. This is the third in a series of three reports 4,5 on the physical properties and degradation processes of materials used in polymer bonded explosive 9501 written for submission to the University of Oregon, Masters Industrial Internship Program.

36 MATERIALS SCIENCE↗

Theoretical Formulation of an Ambient Stress State in Isotropic Elastic Media

Due to the weight of overburden and tectonic forces, the solid earth is subject to an ambient stress state. This stress state is quasi-static in that it is generally in a state of equilibrium. Typically, seismology assumes this ambient stress field has a negligible effect on wave propagation. However, two basic theories have been put forward to describe the effects of ambient stress on wave propagation. Dahlen and Tromp (2002) expound a theory based on perturbation analysis that largely supports the traditional seismological view that ambient stress is negligible for wave propagation. The second theory, espoused by Korneev and Glubokovskikh (2013) and supported by some experimental work, states that perturbation analysis is inappropriate since the elastic modulus is very sensitive to the ambient stress states. This brief report reformulates the equations given by Korneev and Glubokovskikh (2013) into a more compact form that makes it amenable to statement in terms of a pre-stress form of Hooke's Law. Furthermore, this report demonstrates the symmetries of the pre-stress modulus tensor and discusses the reciprocity relationship implied by the symmetry conditions.

58 GEOSCIENCES↗

Theoretical Formulation of an Ambient Stress State in Isotropic Elastic Media

Due to the weight of overburden and tectonic forces, the solid earth is subject to an ambient stress state. This stress state is quasi-static in that it is generally in a state of equilibrium. Typically, seismology assumes this ambient stress field has a negligible effect on wave propagation. However, two basic theories have been put forward to describe the effects of ambient stress on wave propagation. Dahlen and Tromp (2002) expound a theory based on perturbation analysis that largely supports the traditional seismological view that ambient stress is negligible for wave propagation. The second theory, espoused by Korneev and Glubokovskikh (2013) and supported by some experimental work, states that perturbation analysis is inappropriate since the elastic modulus is very sensitive to the ambient stress states. This brief report reformulates the equations given by Korneev and Glubokovskikh (2013) into a more compact form that makes it amenable to statement in terms of a pre-stress form of Hooke's Law. Furthermore, this report demonstrates the symmetries of the pre-stress modulus tensor and discusses the reciprocity relationship implied by the symmetry conditions.

58 GEOSCIENCES↗

Nanoindentation Characterization of FeCrAl C26M tubes

The present report summarizes the nanoindentation characterization of a FeCrAl alloy, C26M in both tube and bar form. Microstructural analysis on the tube using electron backscatter diffraction showed a textured system with the cross-section favoring orie ntations near the [110] and the tube surface near the [111]. The bar cross-section showed a texture with orientation favoring those near the [100]. A large amount of in-grain misorientation was observed in the tube specimen with very little in the bar, indicating cold-work from tube processing steps. Nanoindentation with a Berkovich tip measured a similar modulus for all specimens of ~220 GPa. The bar specimens had a hardness of ~3.9 GPa, significantly lower than the 4.8 GPa and 5.2 GPa for the tube cross-section and surface, respectively. Spherical nanoindentation was performed on all specimens and orientations. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa for all specimens, in agreement with the Berkovich indentation results. The nanoindentation yield strength for the bar was found to be ~0.8 - 0.9 GPa, nearly 0.5 GPa less than the C26M tube.

36 MATERIALS SCIENCE↗