Search NASA⌕ Search

SEARCH · Search NASA

Results for “computer experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

A methodology to compute the critical current limit in Nb3Sn magnets

Numerous experiments have shown that the loads applied to Nb3Sn strands and cables can reduce their critical current. Experiments, performed on uniaxially loaded strands, allowed to define clear laws to describe the evolution of the critical surface as a function of the applied current, field, temperature and strain. It is, however, still unclear how these laws can be applied to superconducting magnets. The present paper proposes a methodology to estimate the critical current and temperature margin reduction on superconducting magnets due to stress on the superconducting material. The methodology is tested on the MQXF magnets, a quadrupole developed for the High Luminosity LHC project, and successfully validated by comparing computed strain with data from strain gauge measurements. Overall, results suggested that, because of the stresses arising in winding during assembly, cool-down and powering, the current limit of the magnet is lower than the expected short sample limit, and that the most critical region does not coincide with the peak field location.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of birthrate granularity on the release-to-birth ratio for the AGR-1 in-core experiment

The AGR-1 Advanced Gas Reactor (AGR) tristructural-isotropic-particle fuel experiment underwent 13 irradiation intervals from December 2006 until November 2009 within the Idaho National Laboratory Advanced Test Reactor in support of the Next Generation Nuclear Power Plant program. During this multi-year experiment, release-to-birth rate ratios were computed at the end of each operating interval to provide information about fuel performance. Fission products released during irradiation were tracked daily by the Fission Product Monitoring System using 8-h measurements. Birth rate calculated by MCNP with ORIGEN for as-run conditions were computed at the end of each irradiation interval. Each time step in MCNP provided neutron flux, reaction rates and AGR-1 compact composition, which were used to determine birth rate using ORIGEN. The initial birth-rate data, consisting of four values for each irradiation interval at the beginning, end, and two intermediate times, were interpolated to obtain values for each 8-h activity. The problem with this method is that any daily changes in heat rates or perturbations, such as shim control movement or core/lobe power fluctuations, would not be reflected in the interpolated data and a true picture of the system would not be presented. At the conclusion of the AGR-1 experiment, great efforts were put forth to compute daily birthrates, which were reprocessed with the 8-h release activity. The results of this study are presented in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Effect of Birthrate Granularity on the Release- to- Birth Ratio for the AGR-1 In-core Experiment

The AGR-1 Advanced Gas Reactor (AGR) tristructural-isotropic-particle fuel experiment underwent 13 irradiation intervals from December 2006 until November 2009 within the Idaho National Laboratory Advanced Test Reactor in support of the Next Generation Nuclear Power Plant program. During this multi-year experiment, release-to-birth rate ratios were computed at the end of each operating interval to provide information about fuel performance. Fission products released during irradiation were tracked daily by the Fission Product Monitoring System using 8-hour measurements. Birth rates calculated by MCNP with ORIGEN for as-run conditions were computed at the end of each irradiation interval. Each time step in MCNP provided neutron flux, reaction rates and AGR-1 compact composition, which were used to determine birth rates using ORIGEN. The initial birth-rate data, consisting of four values for each irradiation interval at the beginning, end, and two intermediate times, were interpolated to obtain values for each 8-hour activity. The problem with this method is that any daily changes in heat rates or perturbations, such as shim control movement or core/lobe power fluctuations, would not be reflected in the interpolated data and a true picture of the system would not be presented. At the conclusion of the AGR-1 experiment, great efforts were put forth to compute daily birthrates, which were reprocessed with the 8-hour release activity. The results of this study are presented in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Verification of Flux Sensitivity Estimates Using the MCNP Tally Perturbation Tool

Nuclear data is commonly used in applications such as nuclear nonproliferation, safeguards, and criticality safety. More specifically, nuclear data is used in predictive simulation codes like the Monte-Carlo N-Particle (MCNP ® ) transport code, Serpent, and similar radiation transport codes. The improvement of nuclear data enables more precise and accurate simulations, which result in higher fidelity designs and reduced operational/procedural costs. Therefore, the improvement of nuclear data is of paramount importance across the nuclear community. Nuclear data is improved and validated through integral benchmark experiments. The design of benchmark experiments is an extensive process; therefore, these experiments are often optimized on multiple characteristics, including sensitivity to the nuclear data, during the design process. Sensitivity is a measure of how much a quantity changes due to changes in independent variables such as experimental configuration. An experimental design that has a larger sensitivity to the nuclear data of interest will have a larger impact on the accuracy and precision of the validated data. Past integral benchmark experiments have primarily used the effective multiplication factor ($k_{eff}$) as the predominant measured quantity; however, experiments designed with other quantities in mind would be able to optimize on validating different areas of the nuclear data. A primary goal of the EUCLID project is to design, constrain, and reduce compensating errors in experiments focused on quantities other than $k_{eff}$ to better validate nuclear data across the board. Currently, there is a capability in MCNP to easily calculate the sensitivity of $k_{eff}$ to specific nuclear data of numerous reactions types and isotopes (KSEN card); however, the sensitivity of other quantities must be estimated in more strenuous manners. For example, the perturbation feature (PERT card) of MCNP can be used to estimate first-order sensitivities of some response in fixed source simulations. A recent announcement revealed that the first- and second-order perturbation features in previous releases of MCNP contained a bug. It was identified that particles were being scored into the wrong energy bin. The bug is in the most recent public release (MCNP6.2); however, a patch has been added to the most up to date version (MCNP6.2.2) that has not been released publicly. A direct comparison of the PERT card results for an F4 (neutron flux averaged over a cell) tally before and after the patch are shown in figure 1. All simulations used in the sensitivity estimates in this report were performed with MCNP6.2.2. This work verifies the patched MCNP perturbation tool by comparing first order sensitivities made using the PERT card to estimates made using manual perturbation of the compact ENDF (ACE) files.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

S-Doped MoP Nanoporous Layer Toward High-Efficiency Hydrogen Evolution in pH-Universal Electrolyte

In this paper, we report a non-precious metal catalyst for high-efficiency hydrogen evolution reaction (HER). A self-organized S-doped MoP nanoporous layer (S-MoP NPL) is achieved through a facile electrochemical anodic process and a two-step chemical vapor deposition treatment, which was directly used as a binder-free catalyst for HER in pH-universal electrolytes. S-MoP NPL exhibits HER behavior with a low overpotential of 86 mV at 10 mA cm -1 and low Tafel slope of 34 mV dec -1 in acidic solution. Moreover, S-MoP NPL also shows high HER activity in basic and neutral electrolytes. Density functional theory (DFT) computations were carried out to support our experiment. The calculations show that the H 2 formation (via Volmer–Heyrovsky mechanism) from the reaction of a metal (Mo) absorbed hydride with a solvated proton is favored over S-MoP than MoS 2 . Both experimental and computational studies demonstrate that the extraordinary HER activity and stability performance displayed by a MoP catalyst can be enhanced by S-doping, opening up a promising paradigm for the conscious design of high-performance non-precious metal catalyst for hydrogen generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measurement of Turbulent Flow Phenomena for the Lower Plenum of a Prismatic Gas-Cooled Reactor

Mean velocity field and turbulence data are presented that measure turbulent flow phenomena in an approximately 1:7 scale model of a region of the lower plenum of a typical prismatic gas-cooled reactor (GCR) similar to a General Atomics design (Gas-Turbine-Modular Helium Reactor). The datawere obtained in the Matched-Index-of-Refraction (MIR) facility at Idaho National Laboratory (INL) and are offered as a benchmark for assessing computational fluid dynamics (CFD) software. This experiment has been selected as the first Standard Problem endorsed by the Generation IV International Forum. The primary objective of this paper is to document the experiment and present a sample of the data set that has been established for this standard problem. Present results concentrate on the region of the lower plenum near its far reflector wall (away from the outlet duct). The flowin the lower plenum consists of multiple jets injected into a confined crossflow—with obstructions. The model consists of a row of full circular posts along its centerline with half-posts on the two parallel walls to approximate flow scaled to that expected from the staggered parallel rows of posts in the reactor design. Posts, side walls and end walls are fabricated from clear, fused quartz to match the refractive index of the mineral oil working fluid so that optical techniques may be employed for the measurements. The benefit of the MIR technique is that it permits optical measurements to determine flow characteristics in complex passages and around objects to be obtained without locating intrusive transducers that will disturb the flow field and without distortion of the optical paths. An advantage of the INL system is its large size, leading to improved spatial and temporal resolution compared to similar facilities at smaller scales. A three-dimensional (3D) particle image velocimetry (PIV) system was used to collect the data. Inlet-jet Reynolds numbers (based on the hydraulic diameter of the jet and the timemean average flow rate) are approximately 4300 and 12,400. Uncertainty analysis and a discussion of the standard problem are included. The measurements reveal complicated flow patterns that include several large recirculation zones, reverse flow near the simulated reflector wall, recirculation zones in the upper portion of the plenum and complex flow patterns around the support posts. Data include three-dimensional PIV images of flow planes, data displays along the coordinate planes (slices) and presentations that describe the component flows at specific regions in the model.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigating size effects of complex nanostructures through Young-Laplace equation and finite element analysis

Analytical studies on the size effects of a simply-shaped beam fixed at both ends have successfully explained the sudden changes of effective Young's modulus as its diameter decreases below 100 nm. Yet they are invalid for complex nanostructures ubiquitously existing in nature. In accordance with a generalized Young-Laplace equation, one of the representative size effects is transferred to non-uniformly distributed pressure against an external surface due to the imbalance of inward and outward loads. Because the magnitude of pressure depends on the principal curvatures, iterative steps have to be adopted to gradually stabilize the structure in finite element analysis. Computational results are in good agreement with both experiment data and theoretical prediction. Furthermore, the investigation on strengthened and softened Young's modulus for two complex nanostructures demonstrates that the proposed computational method provides a general and effective approach to analyze the size effects for nanostructures in arbitrary shape.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Inverse methods for design of soft materials

Functional soft materials, comprising colloidal and molecular building blocks that self-organize into complex structures as a result of their tunable interactions, enable a wide array of technological applications. Inverse methods provide a systematic means for navigating their inherently high-dimensional design spaces to create materials with targeted properties. Furthermore, while multiple physically motivated inverse strategies have been successfully implemented in silico, their translation to guiding experimental materials discovery has thus far been limited to a handful of proof-of-concept studies. In this perspective, we discuss recent advances in inverse methods for design of soft materials that address two challenges: (1) methodological limitations that prevent such approaches from satisfying design constraints and (2) computational challenges that limit the size and complexity of systems that can be addressed. Strategies that leverage machine learning have proven particularly effective, including methods to discover order parameters that characterize complex structural motifs and schemes to efficiently compute macroscopic properties from the underlying structure. We also highlight promising opportunities to improve the experimental realizability of materials designed computationally, including discovery of materials with functionality at multiple thermodynamic states, design of externally directed assembly protocols that are simple to implement in experiments, and strategies to improve the accuracy and computational efficiency of experimentally relevant models.

36 MATERIALS SCIENCE↗

Efficient scatter distribution estimation and correction in CBCT using concurrent Monte Carlo fitting

Purpose: X-ray scatter is a significant impediment to image quality improvements in cone-beam CT (CBCT). The authors present and demonstrate a novel scatter correction algorithm using a scatter estimation method that simultaneously combines multiple Monte Carlo (MC) CBCT simulations through the use of a concurrently evaluated fitting function, referred to as concurrent MC fitting (CMCF). Methods: The CMCF method uses concurrently run MC CBCT scatter projection simulations that are a subset of the projection angles used in the projection set, P, to be corrected. The scattered photons reaching the detector in each MC simulation are simultaneously aggregated by an algorithm which computes the scatter detector response, S{sub MC}. S{sub MC} is fit to a function, S{sub F}, and if the fit of S{sub F} is within a specified goodness of fit (GOF), the simulations are terminated. The fit, S{sub F}, is then used to interpolate the scatter distribution over all pixel locations for every projection angle in the set P. The CMCF algorithm was tested using a frequency limited sum of sines and cosines as the fitting function on both simulated and measured data. The simulated data consisted of an anthropomorphic head and a pelvis phantom created from CT data, simulated with and without the use of a compensator. The measured data were a pelvis scan of a phantom and patient taken on an Elekta Synergy platform. The simulated data were used to evaluate various GOF metrics as well as determine a suitable fitness value. The simulated data were also used to quantitatively evaluate the image quality improvements provided by the CMCF method. A qualitative analysis was performed on the measured data by comparing the CMCF scatter corrected reconstruction to the original uncorrected and corrected by a constant scatter correction reconstruction, as well as a reconstruction created using a set of projections taken with a small cone angle. Results: Pearson’s correlation, r, proved to be a suitable GOF metric with strong correlation with the actual error of the scatter fit, S{sub F}. Fitting the scatter distribution to a limited sum of sine and cosine functions using a low-pass filtered fast Fourier transform provided a computationally efficient and accurate fit. The CMCF algorithm reduces the number of photon histories required by over four orders of magnitude. The simulated experiments showed that using a compensator reduced the computational time by a factor between 1.5 and 1.75. The scatter estimates for the simulated and measured data were computed between 35–93 s and 114–122 s, respectively, using 16 Intel Xeon cores (3.0 GHz). The CMCF scatter correction improved the contrast-to-noise ratio by 10%–50% and reduced the reconstruction error to under 3% for the simulated phantoms. Conclusions: The novel CMCF algorithm significantly reduces the computation time required to estimate the scatter distribution by reducing the statistical noise in the MC scatter estimate and limiting the number of projection angles that must be simulated. Using the scatter estimate provided by the CMCF algorithm to correct both simulated and real projection data showed improved reconstruction image quality.

60 APPLIED LIFE SCIENCES↗

The Integrated Plasma Simulator: A Flexible Python Framework for Coupled Multiphysics Simulation

High-fidelity coupled multiphysics simulations are an increasingly important aspect of computational science. In many domains, however, there has been very limited experience with simulations of this sort, therefore research in coupled multiphysics often requires computational frameworks with significant flexibility to respond to the changing directions of the physics and mathematics. This paper presents the Integrated Plasma Simulator (IPS), a framework designed for loosely coupled simulations of fusion plasmas. The IPS provides users with a simple component architecture into which a wide range of existing plasma physics codes can be inserted as components. Simulations can take advantage of multiple levels of parallelism supported in the IPS, and can be controlled by a high-level ``driver'' component, or by other coordination mechanisms, such as an asynchronous event service. We describe the requirements and design of the framework, and how they were implemented in the Python language. We also illustrate the flexibility of the framework by providing examples of different types of simulations that utilize various features of the IPS.

99 GENERAL AND MISCELLANEOUS↗

Controlling Structural, Electronic, and Energy Flow Dynamics of Catalytic Processes through Tailored Nanostructures

MoS 2 (molybdenum disulfide) is a highly-versatile catalyst material for support of numerous reactions from hydrodesulfurization and denitrogenation to the focus of this renewal proposal: hydrogenation of CO/CO 2 towards (higher) alcohols. At the same time, MoS 2 is a non-toxic, environmentally-benign and rather inert material- which under ambient conditions for some time has served as a lubricant and, more recently, as next-generation electronic material. The apparent contrast between inertness and stability in ambient, and catalytic activity under reactive conditions is puzzling and calls for a synergistic theoretical and experimental investigation with the long-term objective of enabling the rational design of MoS 2 -based catalysts for alcohol-formation reactions by providing a microscopic understanding of the environmental factors that determines site activity and selectivity. Our research project seeks answers to the questions (a) what conformation does MoS 2 adopt under reaction conditions (as opposed to that under ultrahigh vacuum and low temperatures)?; (b) what reaction pathways exist on such a material?; (c) how can the local environment of the active sites be manipulated so as to make MoS 2 an efficient catalyst for production of higher alcohol from syngas? In particular, research strategies will explore how the basal plane composed of sulfur atoms can be activated so as to exhibit a reactivity of its own, by addressing three research targets and building on extensive preliminary and enabling work: (1) vacancies and vacancy aggregates on the basal plane; (2) non-local catalyst transformation through alkali doping, hydrogenation and phase transition; (3) fabrication of a metal-nanoparticle-activated MoS 2 system, in which particle anchoring, reactive sites and pathways as well as selectivity are controlled by design, as an example of predictive development of a catalyst material,. All strategies are directed to improve the efficacy of the key reactive sites and selectivity of chemical pathways by design, to replace the inefficient methodology of trial and error in catalyst development. This research project represents a synergistic combination of computational guidance, foundational surface-science-based experiments and validation under reactive conditions that aims at transformative new insights into the working of MoS 2 -based hydrogenation-catalysts, a topic squarely at the center of the interest of DOE BES. Guided and led by Talat Rahman, a computational physicist, this project will apply density functional theory to understand structure, reaction pathways and chemical potentials associated with MoS 2 -based CO/CO 2 hydrogenation, augmented by kinetic Monte Carlo methods for reaction rates and prefactors as well as ab-initio molecular dynamics for evaluation of thermal stability. Complementary experimental input and validation will originate from co-PI Ludwig Bartels, a physical chemist and materials scientist, whose group focuses on local imaging and preparation of MoS 2 materials, from co-PI Peter Dowben, an experimental physicist, whose group is expert in the spectroscopy of occupied and unoccupied electronic states, and from senior collaborator Michael White of Brookhaven National Laboratory, whose group generates high-resolution electronic and activity information on size-selected well-defined metal chalcogenide clusters. This collaborative effort will enable a comprehensive understanding of the correlation of structural integrity and catalytic activity of MoS 2 in forms ranging from extended films to individual particles with known geometries and binding sites. Alcohol formation from syngas is a rapidly emerging application that has great potential through facile, economic, and decentralized biomass gasification. CO 2 activation is one of the most pressing concerns of our time: increasing CO 2 levels in the atmosphere change the climate and expose the globe to environmental transformations with the potential for enormous economic and societal impact. We will investigate CO/CO 2 hydrogenation via an interdisciplinary research collaboration with established synergy – one that, in accordance with the mission of the DOE, involves accredited Hispanic-Serving Institutions and that, through student exchange with international collaborators and National Labs, will directly benefit a broad spectrum of communities and generate human resources in sciences essential to their future.

2D materials↗

Quantum algorithmic measurement

There has been recent promising experimental and theoretical evidence that quantum computational tools might enhance the precision and efficiency of physical experiments. However, a systematic treatment and comprehensive framework are missing. Here we initiate the systematic study of experimental quantum physics from the perspective of computational complexity. To this end, we define the framework of quantum algorithmic measurements (QUALMs), a hybrid of black box quantum algorithms and interactive protocols. We use the QUALM framework to study two important experimental problems in quantum many-body physics: determining whether a system’s Hamiltonian is time-independent or time-dependent, and determining the symmetry class of the dynamics of the system. We study abstractions of these problems and show for both cases that if the experimentalist can use her experimental samples coherently (in both space and time), a provable exponential speedup is achieved compared to the standard situation in which each experimental sample is accessed separately. Our work suggests that quantum computers can provide a new type of exponential advantage: exponential savings in resources in quantum experiments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Relation of Validation Experiments to Applications: A Nonlinear Approach

Model validation efforts often use a suite of experiments to provide data to test models for predictive use for a targeted application. A question that naturally arises is “Does the experimental suite provide data to adequately test the target application model?” The goal of this article is to develop methodology to partially address this question by utilizing computational models for the individual test suite experiments and for the target application, coupled with linear and nonlinear optimization techniques. The results show that the nonlinear methodology developed represents a significant improvement in ability to address this question, for the application considered.

97 MATHEMATICS AND COMPUTING↗

Beyond Coherent Oxide Heterostructures: Atomic-Scale Structure of Misfit Dislocations

Nanoscale design of complex oxide heterostructures and thin films is imperative as they have significant promise in novel technological applications. A coherent interface is formed in oxide heterostructures with small mismatches, and the lattice mismatch is completely compensated by elastic strain. In semi-coherent oxide heterostructures, when an epitaxial layer is grown on the substrate above the critical thickness of the film, misfit dislocations are formed to mitigate the strain between the two materials with dissimilar lattice constants. Key properties of semi-coherent oxide heterostructures are influenced or even controlled by the presence of misfit dislocations. Thus, it is critical to understand the atomic-scale structure of semi-coherent oxide heterostructures, specifically the structure of misfit dislocations that are ubiquitous at such heterointerfaces. Numerous state-of-the-art experiments have reported emergent phenomena at semi-coherent oxide heterostructures, wherein misfit dislocations play a crucial role. Yet, their atomic-scale and nanoscale structure is not always discernable from experiments. Because of large system sizes, computational studies dedicated to examining misfit dislocations in semi-coherent oxide heterostructures are still in their infancy. This review aims to summarize the recent advancements and challenges involved in computational studies elucidating the atomic-scale structure of misfit dislocations in semi-coherent oxide heterostructures and motivate future computational efforts.

74 ATOMIC AND MOLECULAR PHYSICS↗

Extending the eigCG algorithm to nonsymmetric Lanczos for linear systems with multiple right-hand sides

The technique that was used to build the EigCG algorithm for sparse symmetric linear systems is extended to the nonsymmetric case using the BiCG algorithm. We show that, similarly to the symmetric case, we can build an algorithm that is capable of computing a few smallest magnitude eigenvalues and their corresponding left and right eigenvectors of a nonsymmetric matrix using only a small window of the BiCG residuals while simultaneously solving a linear system with that matrix. For a system with multiple right-hand sides, we give an algorithm that computes incrementally more eigenvalues while solving the first few systems and then uses the computed eigenvectors to deflate BiCGStab for the remaining systems. Our experiments on various test problems, including Lattice QCD, show the remarkable ability of EigBiCG to compute spectral approximations with accuracy comparable to that of the unrestarted, nonsymmetric Lanczos. Furthermore, our incremental EigBiCG followed by appropriately restarted and deflated BiCGStab provides a competitive method for systems with multiple right-hand sides.

Abdel-Rehim, A M↗

Porting Adaptive Ensemble Molecular Dynamics Workflows to the Summit Supercomputer

Molecular dynamics (MD) simulations must take very small (femtosecond) integration steps in simulation-time to avoid numerical errors. Efficient use of parallel programming models and accelerators in state-of-the art MD programs now is pushing Moore’s limit for time-per-MD step. As a result, directly simulating timescales beyond milliseconds will not be attainable directly, even at exascale. However, concepts from statistical physics can be used to combine many parallel simulations to provide information about longer timescales and to adequately sample the simulation space, while preserving details about the dynamics of the system. Implementing such an approach requires a workflow program that allows adaptable steering of task assignments based on extensive statistical analysis of intermediate results. Here we report the implementation of such an adaptable workflow program to drive simulations on the Summit IBM Power System AC922, a pre-exascale supercomputer at the Oak Ridge Leadership Computing Facility (OLCF). We compare to experiences on Titan, Summit’s predecessor, report the performance of the workflow and its components, and describe the porting process. We find that using a workflow program managed by a Mongo database can provide the fault tolerance, scalable performance, task dispatch rate, and reconfigurability required for robust and portable implementation of ensemble simulations such as are used in enhanced-sampling molecular dynamics. This type of workflow generator can also be used to provide adaptive steering of ensemble simulations for other applications in addition to MD.

Ossyra, John R.↗

Diffuse Scattering as an Aid to the Understanding of Polymorphism in Pharmaceuticals

Polymorphism occurs when the same molecular compound can crystallize in more than one distinct crystal structure. Its study is a field of great interest and activity. This is largely driven by its importance in the pharmaceutical industry, but polymorphism is also an issue in the pigments, dyes, and explosives industries. The polymorph formed by a compound generally exerts a strong influence on its solid-state properties. The polymorphic form of a drug molecule may affect the ease of manufacture and processing, shelf life, and most significantly the rate of uptake of the molecule by the human body. They can even vary in toxicity; one polymorph may be safe, while a second may be toxic. In this review of recently published work, we show how diffuse scattering experiments coupled with Monte Carlo (MC) computer modeling can aid in the understanding of polymorphism. Examples of the two common pharmaceuticals, benzocaine and aspirin, both of which are bimorphic, at ambient temperatures, are discussed.

60 APPLIED LIFE SCIENCES↗

A New Experimental Design to Study the Kinetics of Solid Dissolution into Liquids at Elevated Temperature

A new method was developed to study the dissolution of a solid cylinder in a liquid under forced convection at elevated temperature. In the new design, a rotating cylinder was placed concentrically in a crucible fabricated by boring four holes into a blank material for creating an internal volume with a quatrefoil profile. A strong flow in the radial direction in the liquid was created, which was evidently shown by computational fluid dynamic (CFD) calculations and experiments at both room temperature and elevated temperature. The new setup was able to freeze the sample as it was at experimental temperature, particularly the interface between the solid and the liquid. This freezing was necessary to obtain reliable information for understanding the reaction mechanism. This was exemplified by the study of dissolution of a refractory in liquid slag. The absence of flow in the radial direction in the traditional setup using a symmetrical cylinder was also discussed. The differences in the findings by past investigators using the symmetrical cylinder are most likely due to the extent of misalignment of the cylinder in the containment vessel.

36 MATERIALS SCIENCE↗