Search NASA⌕ Search

SEARCH · Search NASA

Results for “grid code”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

RANS and URANS Application with CFL3D

This case was run using CFL3D, a multi-zone Reynolds-averaged Navier-Stokes code developed at NASA Langley [1]. It solves the thin-layer form of the Navier-Stokes equations in each of the (selected) coordinate directions. It can use 1-to-1, patched, or overset grids, and employs local time step scaling, grid sequencing, and multigrid to accelerate convergence to steady state. In time-accurate mode, CFL3D has the option to employ dual-time stepping with subiterations and multigrid, and it achieves second order temporal accuracy. CFL3D is a finite volume method. It uses third-order upwind-biased spatial differencing on the convective and pressure terms, and second-order differencing on the viscous terms; it is globally second-order spatially accurate. The flux difference-splitting (FDS) method of Roe is employed to obtain fluxes at the cell faces. It is advanced in time with an implicit three-factor approximate factorization method.

Rumsey, C. L.↗
NASA NTRS2014

Computational Aerodynamic Analysis of Three-Dimensional Ice Shapes on a NACA 23012 Airfoil

The present study identifies a process for performing computational fluid dynamic calculations of the flow over full three-dimensional (3D) representations of complex ice shapes deposited on aircraft surfaces. Rime and glaze icing geometries formed on a NACA23012 airfoil were obtained during testing in the NASA Glenn Research Center's Icing Research Tunnel (IRT). The ice shape geometries were scanned as a cloud of data points using a 3D laser scanner. The data point clouds were meshed using Geomagic software to create highly accurate models of the ice surface. The surface data was imported into Pointwise grid generation software to create the CFD surface and volume grids. It was determined that generating grids in Pointwise for complex 3D icing geometries was possible using various techniques that depended on the ice shape. Computations of the flow fields over these ice shapes were performed using the NASA National Combustion Code (NCC). Results for a rime ice shape for angle of attack conditions ranging from 0 to 10 degrees and for freestream Mach numbers of 0.10 and 0.18 are presented. For validation of the computational results, comparisons were made to test results from rapid-prototype models of the selected ice accretion shapes, obtained from a separate study in a subsonic wind tunnel at the University of Illinois at Urbana-Champaign. The computational and experimental results were compared for values of pressure coefficient and lift. Initial results show fairly good agreement for rime ice accretion simulations across the range of conditions examined. The glaze ice results are promising but require some further examination.

Aerodynamics↗
NASA NTRS2014

Computational Aerodynamic Analysis of Three-Dimensional Ice Shapes on a NACA 23012 Airfoil

The present study identifies a process for performing computational fluid dynamic calculations of the flow over full three-dimensional (3D) representations of complex ice shapes deposited on aircraft surfaces. Rime and glaze icing geometries formed on a NACA23012 airfoil were obtained during testing in the NASA Glenn Research Centers Icing Research Tunnel (IRT). The ice shape geometries were scanned as a cloud of data points using a 3D laser scanner. The data point clouds were meshed using Geomagic software to create highly accurate models of the ice surface. The surface data was imported into Pointwise grid generation software to create the CFD surface and volume grids. It was determined that generating grids in Pointwise for complex 3D icing geometries was possible using various techniques that depended on the ice shape. Computations of the flow fields over these ice shapes were performed using the NASA National Combustion Code (NCC). Results for a rime ice shape for angle of attack conditions ranging from 0 to 10 degrees and for freestream Mach numbers of 0.10 and 0.18 are presented. For validation of the computational results, comparisons were made to test results from rapid-prototype models of the selected ice accretion shapes, obtained from a separate study in a subsonic wind tunnel at the University of Illinois at Urbana-Champaign. The computational and experimental results were compared for values of pressure coefficient and lift. Initial results show fairly good agreement for rime ice accretion simulations across the range of conditions examined. The glaze ice results are promising but require some further examination.

Aerodynamics↗
NASA NTRS2011

Effects of Non-Equilibrium Chemistry and Darcy-Forchheimer Flow of Pyrolysis Gas for a Charring Ablator

The Fully Implicit Ablation and Thermal Response code, FIAT, simulates pyrolysis and ablation of thermal protection materials and systems. The governing equations, which include energy conservation, a three-component decomposition model, and a surface energy balance, are solved with a moving grid. This work describes new modeling capabilities that are added to a special version of FIAT. These capabilities include a time-dependent pyrolysis gas flow momentum equation with Darcy-Forchheimer terms and pyrolysis gas species conservation equations with finite-rate homogeneous chemical reactions. The total energy conservation equation is also enhanced for consistency with these new additions. Parametric studies are performed using this enhanced version of FIAT. Two groups of analyses of Phenolic Impregnated Carbon Ablator (PICA) are presented. In the first group, an Orion flight environment for a proposed Lunar-return trajectory is considered. In the second group, various test conditions for arcjet models are examined. The central focus of these parametric studies is to understand the effect of pyrolysis gas momentum transfer on PICA material in-depth thermal responses with finite-rate, equilibrium, or frozen homogeneous gas chemistry. Results are presented, discussed, and compared with those predicted by the baseline PICA/FIAT ablation and thermal response model developed by the Orion Thermal Protection System Advanced Development Project.

Ablation↗
NASA NTRSDate not supplied

A Comparison of Rotor Disk Modeling and Blade-Resolved CFD Simulations for NASA's Tiltwing Air Taxi

A multi-fidelity computational fluid dynamics analysis is carried out for NASA’s tiltwing air taxi concept operating in airplane and helicopter mode. High-fidelity simulations are computationally expensive due to individual rotor blade modeling in a time-dependent computational domain with rotating grids. The mid-fidelity rotor disk option, in its source term implementation, is explored as a more affordable alternative. Computations are performed with NASA’s OVERFLOW flow solver loosely-coupled with the comprehensive code CAMRAD II for appropriate rotor trim. Detailed comparisons are shown for the trim solution, airloads, wake geometry, and rotor performance. While the rotor disk model is able to capture the flow field with satisfactory agreement in airplane mode, it faces difficulties in helicopter mode due to the three-dimensional effects of the wake. Although this study is limited to a specific vehicle geometry, it is expected that the results are somewhat generalizable to the analysis of multi-rotor configurations.

ARMD↗
NASA NTRSDate not supplied

A Wall-Distance Method for Turbulence Modeling

The distance from a grid point to the closest wall surface, wall distance, is a funda- mental quantity in turbulence modeling. Efficiency of wall-distance calculations has become more critical as the size of computational grids has significantly increased in recent years. This paper reports on an initial implementation of a new search-based wall-distance method that is suitable for general unstructured computational fluid dynamics (CFD) grids and tailored for requirements specific for turbulence modeling. The method represents a two-step approach to calculate the wall distance. In the first step, the wall distance is approximated for each grid point as the minimum distance from this point to a vertex of a triangular face at the wall. The point-to-vertex distance calculation is relatively inexpensive but may lead to a significant error in the wall-distance ap- proximation, especially for grid points near the wall. In the second step, for grid points located within a predefined distance ( threshold ) from the wall, the wall distance is computed as the minimum distance to wall faces. As a result, the wall distance is exact for all grid points within the threshold. This two-step approach reduces the computational cost yet achieves high and controllable accuracy in the evaluation of the wall distance. Algorithmic enhancements are presented to improve efficiency of wall-distance computations. Comprehensive assessment of the new method is reported for large-scale unstructured CFD grids generated for the Fifth AIAA CFD High-Lift Prediction Workshop. The performance of the new wall-distance method compares favorably with performance of two established methods implemented in high-performance CFD codes.

Wall Distance↗
NASA NTRSDate not supplied

Transition prediction in hypersonic regime on complex geometries with RANS-based models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗
NASA NTRSDate not supplied

Transition Prediction in Hypersonic Regime on Complex Geometries With Rans-Based Models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗
NASA NTRS1995

Navier-Stokes Aerodynamic Simulation of the V-22 Osprey on the Intel Paragon MPP

The paper will describe the Development of a general three-dimensional multiple grid zone Navier-Stokes flowfield simulation program (ENS3D-MPP) designed for efficient execution on the Intel Paragon Massively Parallel Processor (MPP) supercomputer, and the subsequent application of this method to the prediction of the viscous flowfield about the V-22 Osprey tiltrotor vehicle. The flowfield simulation code solves the thin Layer or full Navier-Stoke's equation - for viscous flow modeling, or the Euler equations for inviscid flow modeling on a structured multi-zone mesh. In the present paper only viscous simulations will be shown. The governing difference equations are solved using a time marching implicit approximate factorization method with either TVD upwind or central differencing used for the convective terms and central differencing used for the viscous diffusion terms. Steady state or Lime accurate solutions can be calculated. The present paper will focus on steady state applications, although time accurate solution analysis is the ultimate goal of this effort. Laminar viscosity is calculated using Sutherland's law and the Baldwin-Lomax two layer algebraic turbulence model is used to compute the eddy viscosity. The Simulation method uses an arbitrary block, curvilinear grid topology. An automatic grid adaption scheme is incorporated which concentrates grid points in high density gradient regions. A variety of user-specified boundary conditions are available. This paper will present the application of the scalable and superscalable versions to the steady state viscous flow analysis of the V-22 Osprey using a multiple zone global mesh. The mesh consists of a series of sheared cartesian grid blocks with polar grids embedded within to better simulate the wing tip mounted nacelle. MPP solutions will be shown in comparison to equivalent Cray C-90 results and also in comparison to experimental data. Discussions on meshing considerations, wall clock execution time, load balancing, and scalability will be provided.

Vadyak, Joseph↗
NASA NTRS1993

Four-Nozzle Benchmark Wind Tunnel Model USA Code Solutions for Simulation of Multiple Rocket Base Flow Recirculation at 145,000 Feet Altitude

Multiple rocket exhaust plume interactions at high altitudes can produce base flow recirculation with attendant alteration of the base pressure coefficient and increased base heating. A search for a good wind tunnel benchmark problem to check grid clustering technique and turbulence modeling turned up the experiment done at AEDC in 1961 by Goethert and Matz on a 4.25-in. diameter domed missile base model with four rocket nozzles. This wind tunnel model with varied external bleed air flow for the base flow wake produced measured p/p(sub ref) at the center of the base as high as 3.3 due to plume flow recirculation back onto the base. At that time in 1961, relatively inexpensive experimentation with air at gamma = 1.4 and nozzle A(sub e)/A of 10.6 and theta(sub n) = 7.55 deg with P(sub c) = 155 psia simulated a LO2/LH2 rocket exhaust plume with gamma = 1.20, A(sub e)/A of 78 and P(sub c) about 1,000 psia. An array of base pressure taps on the aft dome gave a clear measurement of the plume recirculation effects at p(infinity) = 4.76 psfa corresponding to 145,000 ft altitude. Our CFD computations of the flow field with direct comparison of computed-versus-measured base pressure distribution (across the dome) provide detailed information on velocities and particle traces as well eddy viscosity in the base and nozzle region. The solution was obtained using a six-zone mesh with 284,000 grid points for one quadrant taking advantage of symmetry. Results are compared using a zero-equation algebraic and a one-equation pointwise R(sub t) turbulence model (work in progress). Good agreement with the experimental pressure data was obtained with both; and this benchmark showed the importance of: (1) proper grid clustering and (2) proper choice of turbulence modeling for rocket plume problems/recirculation at high altitude.

Dougherty, N. S.↗
NASA NTRS1995

Algorithms for parallel flow solvers on message passing architectures

The purpose of this project has been to identify and test suitable technologies for implementation of fluid flow solvers -- possibly coupled with structures and heat equation solvers -- on MIMD parallel computers. In the course of this investigation much attention has been paid to efficient domain decomposition strategies for ADI-type algorithms. Multi-partitioning derives its efficiency from the assignment of several blocks of grid points to each processor in the parallel computer. A coarse-grain parallelism is obtained, and a near-perfect load balance results. In uni-partitioning every processor receives responsibility for exactly one block of grid points instead of several. This necessitates fine-grain pipelined program execution in order to obtain a reasonable load balance. Although fine-grain parallelism is less desirable on many systems, especially high-latency networks of workstations, uni-partition methods are still in wide use in production codes for flow problems. Consequently, it remains important to achieve good efficiency with this technique that has essentially been superseded by multi-partitioning for parallel ADI-type algorithms. Another reason for the concentration on improving the performance of pipeline methods is their applicability in other types of flow solver kernels with stronger implied data dependence. Analytical expressions can be derived for the size of the dynamic load imbalance incurred in traditional pipelines. From these it can be determined what is the optimal first-processor retardation that leads to the shortest total completion time for the pipeline process. Theoretical predictions of pipeline performance with and without optimization match experimental observations on the iPSC/860 very well. Analysis of pipeline performance also highlights the effect of uncareful grid partitioning in flow solvers that employ pipeline algorithms. If grid blocks at boundaries are not at least as large in the wall-normal direction as those immediately adjacent to them, then the first processor in the pipeline will receive a computational load that is less than that of subsequent processors, magnifying the pipeline slowdown effect. Extra compensation is needed for grid boundary effects, even if all grid blocks are equally sized.

Vanderwijngaart, Rob F.↗
NASA NTRS1992

Elliptic surface grid generation in three-dimensional space

A methodology for surface grid generation in three dimensional space is described. The method solves a Poisson equation for each coordinate on arbitrary surfaces using successive line over-relaxation. The complete surface curvature terms were discretized and retained within the nonhomogeneous term in order to preserve surface definition; there is no need for conventional surface splines. Control functions were formulated to permit control of grid orthogonality and spacing. A method for interpolation of control functions into the domain was devised which permits their specification not only at the surface boundaries but within the interior as well. An interactive surface generation code which makes use of this methodology is currently under development.

Kania, Lee↗
NASA NTRS1992

Commercial turbofan engine exhaust nozzle flow analyses using PAB3D

Recent developments of a three-dimensional (PAB3D) code have paved the way for a computational investigation of complex aircraft aerodynamic components. The PAB3D code was developed for solving the simplified Reynolds Averaged Navier-Stokes equations in a three-dimensional multiblock/multizone structured mesh domain. The present analysis was applied to commercial turbofan exhaust flow systems. Solution sensitivity to grid density is presented. Laminar flow solutions were developed for all grids and two-equation k-epsilon solutions were developed for selected grids. Static pressure distributions, mass flow and thrust quantities were calculated for on-design engine operating conditions. Good agreement between predicted surface static pressures and experimental data was observed at different locations. Mass flow was predicted within 0.2 percent of experimental data. Thrust forces were typically within 0.4 percent of experimental data.

Abdol-Hamid, Khaled S.↗
NASA NTRS1993

Three-dimensional unsteady flow calculations in an advanced gas generator turbine

This paper deals with the application of a three-dimensional, unsteady Navier-Stokes code for predicting the unsteady flow in a single stage of an advanced gas generator turbine. The numerical method solves the three-dimensional thin-layer Navier-Stokes equations, using a system of overlaid grids, which allow for relative motion between the rotor and stator airfoils. Results in the form of time averaged pressures and pressure amplitudes on the airfoil surfaces will be shown. In addition, instantaneous contours of pressure, Mach number, etc. will be presented in order to provide a greater understanding of the inviscid as well as the viscous aspects of the flowfield. Also, relevant secondary flow features such as cross-plane velocity vectors and total pressure contours will be presented. Prior work in two-dimensions has indicated that for the advanced designs, the unsteady interactions can play a significant role in turbine performance. These interactions affect not only the stage efficiency but can substantially alter the time-averaged features of the flow. This work is a natural extension of the work done in two-dimensions and hopes to address some of the issues raised by the two-dimensional calculations. These calculations are being performed as an integral part of an actual design process and demonstrate the value of unsteady rotor-stator interaction calculations in the design of turbomachines.

Rangwalla, Akil A.↗
NASA NTRS1995

PARC3D calculations of the F/A-18A HARV inlet vortex generators

NASA Lewis Research Center is currently engaged in a research effort as a team member of the High Alpha Technology Program within the NASA agency. This program uses a specially-equipped F/A-18A aircraft called the High Alpha Research Vehicle (HARV), in an effort to improve the maneuverability of high performance military aircraft at low-subsonic-speed, high-angle-of-attack conditions. The overall objective of the NASA Lewis effort is to develop inlet analysis technology towards efficient airflow delivery to the engine during these maneuvers. One portion of this inlet analysis technology uses computational fluid dynamics to predict installed inlet performance. Most of the F/A-18A HARV geometry, which includes the ramp/splitter plate, side diverter and slot, inlet lip and upper diverter, and deflected leading-edge flap has been modeled. The empennage and rear fuselage have not. A pair of vortex generators located on the bottom wall of the inlet were not modeled initially. These vortex generators were installed to alleviate any flow separation that may be induced by the wheel well protrusion into the inlet wall. Calculations completed with the PARC3D code showed that the pressure recovery has been underpredicted and the flow distortion over-predicted. To improve the correlation of PARC3D predictions with flight and wind tunnel tests, the vortex generators were included in the grid geometry and the results are presented in this report. The grid totals 27 blocks or 1.3 million grid points for the half model, which includes the vortex generator grid blocks. Two flight cases were calculated, a high speed case with a Mach number of 0.8 and angle of attack of 3.4; and a low speed case with a Mach number of 0.43 and angle of attack of 32.2. The vortex generators have a significant effect on the inlet boundary layers at high speed, low angle of attack; and have no effect at low speed, high angle of attack.

Podleski, Steve D.↗
NASA NTRS1996

Parallel implementation of an adaptive scheme for 3D unstructured grids on the SP2

Dynamic mesh adaption on unstructured grids is a powerful tool for computing unsteady flows that require local grid modifications to efficiently resolve solution features. For this work, we consider an edge-based adaption scheme that has shown good single-processor performance on the C90. We report on our experience parallelizing this code for the SP2. Results show a 47.0X speedup on 64 processors when 10 percent of the mesh is randomly refined. Performance deteriorates to 7.7X when the same number of edges are refined in a highly-localized region. This is because almost all the mesh adaption is confined to a single processor. However, this problem can be remedied by repartitioning the mesh immediately after targeting edges for refinement but before the actual adaption takes place. With this change, the speedup improves dramatically to 43.6X.

Strawn, Roger C.↗
NASA NTRS1996

Parallel Implementation of an Adaptive Scheme for 3D Unstructured Grids on the SP2

Dynamic mesh adaption on unstructured grids is a powerful tool for computing unsteady flows that require local grid modifications to efficiently resolve solution features. For this work, we consider an edge-based adaption scheme that has shown good single-processor performance on the C90. We report on our experience parallelizing this code for the SP2. Results show a 47.OX speedup on 64 processors when 10% of the mesh is randomly refined. Performance deteriorates to 7.7X when the same number of edges are refined in a highly-localized region. This is because almost all mesh adaption is confined to a single processor. However, this problem can be remedied by repartitioning the mesh immediately after targeting edges for refinement but before the actual adaption takes place. With this change, the speedup improves dramatically to 43.6X.

Oliker, Leonid↗
NASA NTRS2001

A Global Magnetohydrodynamic Model of Jovian Magnetosphere

The goal of this project was to develop a new global magnetohydrodynamic model of the interaction of the Jovian magnetosphere with the solar wind. Observations from 28 orbits of Jupiter by Galileo along with those from previous spacecraft at Jupiter, Pioneer 10 and 11, Voyager I and 2 and Ulysses, have revealed that the Jovian magnetosphere is a vast, complicated system. The Jovian aurora also has been monitored for several years. Like auroral observations at Earth, these measurements provide us with a global picture of magnetospheric dynamics. Despite this wide range of observations, we have limited quantitative understanding of the Jovian magnetosphere and how it interacts with the solar wind. For the past several years we have been working toward a quantitative understanding of the Jovian magnetosphere and its interaction with the solar wind by employing global magnetohydrodynamic simulations to model the magnetosphere. Our model has been an explicit MHD code (previously used to model the Earth's magnetosphere) to study Jupiter's magnetosphere. We continue to obtain important insights with this code, but it suffers from some severe limitations. In particular with this code we are limited to considering the region outside of 15RJ, with cell sizes of about 1.5R(sub J). The problem arises because of the presence of widely separated time scales throughout the magnetosphere. The numerical stability criterion for explicit MHD codes is the CFL limit and is given by C(sub max)(Delta)t/(Delta)x less than 1 where C(sub max) is the maximum group velocity in a given cell, (Delta)x is the grid spacing and (Delta)t is the time step. If the maximum wave velocity is C(sub w) and the flow speed is C(sub f), C(sub max) = C(sub w) + C(sub f). Near Jupiter the Alfven wave speed becomes very large (it approaches the speed of light at one Jovian radius). Operating with this time step makes the calculation essentially intractable. Therefore under this funding we have been designing a new MHD model that will be able to compute solutions in the wide parameter regime of the Jovian magnetosphere.

Walker, Raymond J.↗