Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase field method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Multiferroics properties in BiFeO{sub 3}/CoFe{sub 2}O{sub 4} heterostructures thin films deposited on (111) SrTiO{sub 3}

The multiferroic properties of BiFeO{sub 3}-CoFe{sub 2}O{sub 4} (BFO-CFO) heterostructures thin film grown on (111) SrTiO{sub 3} (STO) substrates by employing pulsed laser deposition (PLD) method, have been studied.X ray diffraction analysis reveals the presence of BFO and CFO in two separate phases. The heterostructures BFO/CFO/STO(111) thin films show well – shaped hysteresis loop with saturated magnetization and coercive field, which are much larger than pure BFO/STO thin film. The frequency dependent dielectric anomalies in BFO-CFO multilayer are attributed to the interfacial effect across the presence of CFO as a separate phase embedded in BFO matrix.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparison of the dielectric and magnetocaloric properties of bulk and film of GdFe 0.5 Cr 0.5 O 3

Here, we report a comparison of the magnetic, magnetocaloric, and dielectric properties of 50% iron substituted GdCrO 3 (GdFe 0.5 Cr 0.5 O 3 ) bulk pellet and 960 nm thick film of GdFe 0.5 Cr 0.5 O 3 (GFCO). The 960 nm film was synthesized on a platinized-silicon substrate by chem. soln. deposition and spin-coating methods. The X-ray diffraction scans of the bulk sample and the film as well as the morphology of the film as examined by the field-emission scanning electron microscope indicate phase-pure and polycrystalline nature of these samples. XPS was used to deermine the valence states of Gd, Fe, and Cr. The temp. dependence of the dielectric const. from 225 to 700 K shows peaks at T C = 525 K for the bulk and ≈450 K for the film due to ferroelectric to paraelectric transitions, since elec. polarization vs elec. field hysteresis loops are observed. at room temp. The dielectric studies in the bulk GFCO for T > T C indicate a relaxor-like behavior. The measurements of the magnetization (M) of the samples as a function of temp. (5-350 K) and magnetic field (H) up to 7 T (=70 kOe) depict hysteresis behavior at low temps. due to the canted antiferromagnetic order of Fe 3+ /Cr 3+ below the Néel temp. of ≈275 K. The M vs H isotherms at various temps. are used to det. and compare the magnetic entropy change (-ΔS) and relative cooling power (RCP) of the two samples, yielding (-ΔS) = 30.7 J/kg K (18.8 J/kg K) and RCP = 566.5 J/kg (375 J/kg) for the bulk (960 nm film) samples of GFCO at 7 K and 7 T, resp. The plot of RCP vs T shows that magnetic cooling for this system is most effective for T < 30 K. Comparatively smaller magnitudes of (-ΔS) and RCP for the film vis-a-vis the bulk sample of GFCO scale with its reduced magnetization. This suggests that further improvements in the quality of the films are needed to improve their magnetization and hence their magnetocaloric properties, possibly making them useful for on-chip cooling in miniaturized devices.

36 MATERIALS SCIENCE↗

Many routes to ferroelectric HfO 2 : A review of current deposition methods

Although 10 years have passed since the initial report of ferroelectricity in hafnia (HfO 2 ), researchers are still intensely fascinated by this material system and the promise it holds for future applications. A wide variety of deposition methods have been deployed to create ferroelectric HfO 2 thin films such as atomic layer deposition, chemical solution deposition, and physical vapor deposition methods such as sputtering and pulsed laser deposition. Process and design parameters such as deposition temperature, precursor choice, target source, vacuum level, reactive gases, substrate strain, and many others are often integral in stabilizing the polar orthorhombic phase and ferroelectricity. We examine processing parameters across four main different deposition methods and their effect on film microstructure, phase evolution, defect concentration, and resultant electrical properties. The goal of this review is to integrate the process knowledge collected over the past 10 years in the field of ferroelectric HfO 2 into a single comprehensive guide for the design of future HfO 2 -based ferroelectric materials and devices.

36 MATERIALS SCIENCE↗

Analytical study of bound states in graphene nanoribbons and carbon nanotubes: The variable phase method and the relativistic Levinson theorem

The problem of localized states in 1D systems with a relativistic spectrum, namely, graphene stripes and carbon nanotubes, is studied analytically. The bound state as a superposition of two chiral states is completely described by their relative phase, which is the foundation of the variable phase method (VPM) developed herein. Based on our VPM, we formulate and prove the relativistic Levinson theorem. The problem of bound states can be reduced to the analysis of closed trajectories of some vector field. Remarkably, the Levinson theorem appears as the Poincaré index theorem for these closed trajectories. The VPM equation is also reduced to the nonrelativistic and semiclassical limits. The limit of a small momentum p{sub y} of transverse quantization is applicable to an arbitrary integrable potential. In this case, a single confined mode is predicted.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Capacitance-voltage characteristics of (Al/Ti)/Al{sub 2}O{sub 3}/n-GaN MIS structures

The capacitance-voltage characteristics of (Al/Ti)/Al{sub 2}O{sub 3}/n-GaN metal—insulator-semiconductor (MIS) structures are measured and analyzed. n-Type GaN films are grown on sapphire (0001) substrates by the metal-organic chemical vapor deposition method. An aluminum-oxide layer with a thickness of 60 nm is deposited onto the surface of GaN by the method of atomic-layer deposition from the gas phase. Metallic contacts are deposited by the electron-beam evaporation of titanium and aluminum in vacuum. According to the measurement results, the breakdown-field strength of the oxide, its dielectric constant, and the integrated electron density of states at the oxide-semiconductor interface are 5 × 10{sup 6} V/cm, 7.5, and 3 × 10{sup 12} cm{sup −2}, respectively.

36 MATERIALS SCIENCE↗

Microearthquake Studies at the Salton Sea Geothermal Field

The objective of this project is to detect and locate microearthquakes to aid in the characterization of reservoir fracture networks. Accurate identification and mapping of the large numbers of microearthquakes induced in EGS is one technique that provides diagnostic information when determining the location, orientation and length of underground crack systems for use in reservoir development and management applications. Conventional earthquake location techniques often are employed to locate microearthquakes. However, these techniques require labor-intensive picking of individual seismic phase onsets across a network of sensors. For this project we adapt the Matched Field Processing (MFP) technique to the elastic propagation problem in geothermal reservoirs to identify more and smaller events than traditional methods alone.

15 GEOTHERMAL ENERGY↗

Deep Controlled Source Electro-Magnetic Sensing: A Cost Effective, Long-Term Tool for Sequestration Monitoring

The proposed system was designed to operate as a permanent, autonomous monitoring and data collection system that can provide much higher temporal data density than can be achieved economically with 3-Dimensional (3D) seismic surveys. It can operate over broad areas for long periods of time providing full 3D data sets on a monthly basis at a very low cost. By borrowing techniques commonly used in marine CSEM, structural information from background seismic surveys can be incorporated into the CSEM modeling to provide high resolution models of CO 2 progression within reservoirs. The system uses borehole-based vertical-electric-dipole sources placed at reservoir depths in the formation. The electric and magnetic fields induced by this source are received on the surface using an array of stations. The project was conducted in three phases. Phase I demonstrated the feasibility of the system to collect static/reference data at the Ketzin CO 2 storage pilot site in Germany. In Phase I, numerical modeling was used to determine the optimal configurations and requirements for sensor sensitivity and data accuracy. Based on the model results, existing hardware and software were modified. The CSEM system was then field tested at the Ketzin site. The data were imaged and the results were compared with independent studies of the reservoir and overburden geo-electrical characteristics. Phase II demonstrated the ability to provide sensitive, cost-effective measurement of changes in reservoir properties and changes in the overlying formations using a second round of measurements at the Ketzin site. A prototype autonomous recording system was developed and tested as a subset of the measurement points. Phase III of the project quantified the advantages (and disadvantages) of the fully autonomous data collection subsystems by comparing them with repeated measurements made with mobile stations. The Phase III also provided an additional time point in measuring post-closure changes in and above the Ketzin CO 2 injection site. Validation of the CSEM field survey results were completed using a method such as other alternative and available field site data.

58 GEOSCIENCES↗

A statistical formulation of one-dimensional electron fluid turbulence

A one-dimensional electron fluid model is investigated using the mathematical methods of modern fluid turbulence theory. Non-dissipative equilibrium canonical distributions are determined in a phase space whose co-ordinates are the real and imaginary parts of the Fourier coefficients for the field variables. Spectral densities are calculated, yielding a wavenumber electric field energy spectrum proportional to k to the negative second power for large wavenumbers. The equations of motion are numerically integrated and the resulting spectra are found to compare well with the theoretical predictions.

Fyfe, D.↗

A scatter model for vegetation up to Ku-band

A scatter model is developed based on the matrix doubling method for volume scattering and the Kirchhoff method in rough surface scattering. Scattering from vegetation is assumed to be dominated by leaves and a single leaf is modeled by a thin dielectric disk. In developing the phase matrix for the disk, field within the disk is taken to be constant over the disk thickness, but phase changes across the surface of the disk are accounted for. Comparisons of this scatter model with radar measurements indicate good agreements in polarization, angular trends, and frequency up to Ku-band. This represents a considerable improvement over low-frequency scatter models which are valid up to S-band.

Eom, H. J.↗

Remote sensing of the atmospheric aerosols and noctilucent clouds from space

The method for the determination of the optical density of tropospheric and mesospheric aerosols and for the estimation of the scattering phase function in the forward directions (0 to 30 deg) is proposed. The method is based on measurements of the brightness of the twilight horizon with the high resolution limb camera having five separated fields of view. In some detail the features of the camera are described and the mathematical aspects of remote sensing data inversion are discussed.

Avaste, O.↗

ATD-2 Benefits Mechanism

NASA has been developing and demonstrating a suite of decision support capabilities for integrated arrival, departure, and surface (IADS) operations in a metroplex environment. The effort is being made in three phases, under NASA’s Airspace Technology Demonstration 2 (ATD-2) sub-project, through a close partnership with the Federal Aviation Administration (FAA), air carriers, airport, and general aviation community. The Phase 1 Baseline IADS capabilities provide enhanced operational efficiency and predictability of flight operations through data exchange and integration, tactical surface metering, and automated coordination of release time of controlled flights for overhead stream insertion. The Phase 2 Fused IADS capabilities include the fusion of strategic and tactical surface metering, Atlanta Center airspace tactical scheduling, Electronic Flight Data (EFD) integration, Terminal Flight Data Manager (TFDM) Terminal Publication (TTP) prototype, and Mobile App for General Aviation (GA) community. In the Phase 2 field evaluation, strategic surface metering provides advance notice of metering and additional stability to the assigned gate holds. The users of the IADS system in Phases 1 and 2 include the personnel at Charlotte Douglas International Airport (CLT) air traffic control tower, American Airlines ramp tower, CLT terminal radar approach control (TRACON), and Washington and Atlanta Center. This document describes the ATD-2 benefits mechanism used to assess the Phases 1 and 2 IADS capabilities and field evaluation conducted at CLT since September 2017. The ATD-2 benefits mechanism mainly consists of surface metering and overhead stream insertion. This document provides detailed calculation methods of major benefit metrics, such as fuel savings, gas emissions savings, and engine runtime reduction, which can be obtained through surface metering, gate hold of Approval Request (APREQ) flights prior to pushback, and the renegotiation of release time while taxiing. As of March 31, 2020, it is estimated that 5,075,981 pounds of fuel savings and 15,634,022 pounds of CO2 emission reduction have been achieved so far, with a reduction of 3,832 hours in total engine runtime. The amount of CO2 savings is estimated to be equivalent to planting 116,254 urban trees. The pre- and post-metering comparison results using FAA’s Aviation System Performance Metrics (ASPM) data have also shown that the surface metering had no negative impact on the on-time arrival performance of both outbound and inbound flights at CLT.

ATD-2↗

ATD-2 Benefits Mechanism

NASA has been developing and demonstrating a suite of decision support capabilities for integrated arrival, departure, and surface (IADS) operations in a metroplex environment. The effort is being made in three phases, under NASA’s Airspace Technology Demonstration 2 (ATD-2) sub-project, through a close partnership with the Federal Aviation Administration (FAA), air carriers, airport, and general aviation community. The Phase 1 Baseline IADS capabilities provide enhanced operational efficiency and predictability of flight operations through data exchange and integration, tactical surface metering, and automated coordination of release time of controlled flights for overhead stream insertion. The Phase 2 Fused IADS capabilities include the fusion of strategic and tactical surface metering, Atlanta Center airspace tactical scheduling, Electronic Flight Data (EFD) integration, Terminal Flight Data Manager (TFDM) Terminal Publication (TTP) prototype, and Mobile App for General Aviation (GA) community. In the Phase 2 field evaluation, strategic surface metering provides advance notice of metering and additional stability to the assigned gate holds. The users of the IADS system in Phases 1 and 2 include the personnel at Charlotte Douglas International Airport (CLT) air traffic control tower, American Airlines ramp tower, CLT terminal radar approach control (TRACON), and Washington and Atlanta Center. This document describes the ATD-2 benefits mechanism used to assess the Phases 1 and 2 IADS capabilities and field evaluation conducted at CLT since September 2017. The ATD-2 benefits mechanism mainly consists of surface metering and overhead stream insertion. This document provides detailed calculation methods of major benefit metrics, such as fuel savings, gas emissions savings, and engine runtime reduction, which can be obtained through surface metering, gate hold of Approval Request (APREQ) flights prior to pushback, and the renegotiation of release time while taxiing. As of April 30, 2020, it is estimated that 5,097,173 pounds of fuel savings and 15,699,292 pounds of CO2 emission reduction have been achieved so far, with a reduction of 3,831 hours in total engine runtime. The amount of CO2 savings is estimated to be equivalent to planting 116,739 urban trees. The pre- and post-metering comparison results using FAA’s Aviation System Performance Metrics (ASPM) data have also shown that the surface metering had no negative impact on the on-time arrival performance of both outbound and inbound flights at CLT.

ATD-2↗

Phased Array Characterization of Slat Noise Radiation from a High-Lift Common Research Model

A test campaign was conducted in the open-jet test section of the NASA Langley 14- by 22-Foot Subsonic Tunnel on a 10%-scale, semispan version of a High-Lift Common Research Model (CRM-HL) incorporating a leading-edge slat, trailing-edge flap and removable high-fidelity main landing gear. Far field acoustic measurements were obtained on baseline and acoustically treated model configurations using a traversing 97-microphone phased array that viewed the pressure side of the airframe. A modified version of the DAMAS deconvolution method incorporating corrections for shear layer acoustic wave decorrelation was employed to determine the locations and strengths of relevant noise sources along the span of the slat and in the vicinity of the flap edges and landing gear. The main goal of the test campaign was to use the array data to evaluate the effectiveness of various slat noise reduction concepts. It was found that slat-gap fillers produced significant broadband noise reduction for all Mach numbers and airfoil angles of attack that were investigated. Mach number scaling revealed an approximate velocity to the sixth power relationship for the slat noise at higher frequencies. Directivity measurements obtained from integration of DAMAS pressure-squared values over defined geometric zones around the model showed that baseline slat noise radiation approximated a dipole as a function of polar emission angle, becoming approximately omnidirectional with the introduction of the slat-gap filler. The test campaign clearly demonstrated the noise reduction benefits that can be obtained by applying appropriate treatments to leading edge slats on commercial transport-class aircraft.

William M Humphreys, Jr.↗

MO-AB-BRA-03: Calorimetry-Based Absorbed Dose to Water Measurements Using Interferometry

Purpose: Interferometry-based calorimetry is a novel technique to measure radiation-induced temperature changes allowing the measurement of absorbed dose to water (ADW). There are no mechanical components in the field. This technique also has the possibility of obtaining 2D dose distributions. The goal of this investigation is to calorimetrically-measure doses between 2.5 and 5 Gy over a single projection in a photon beam using interferometry and compare the results with doses calculated using the TG-51 linac calibration. Methods: ADW was determined by measuring radiation-induced phase shifts (PSs) of light passing through water irradiated with a 6 MV photon beam. A 9×9×9 cm{sup 3} glass phantom filled with water and placed in an arm of a Michelson interferometer was irradiated with 300, 400, 500 and 600 monitor units. The whole system was thermally insulated to achieve sufficient passive temperature control. The depth of measurement was 4.5 cm with a field size of 7×7 cm{sup 2}. The intensity of the fringe pattern was monitored with a photodiode and used to calculate the time-dependent PS curve. Data was acquired 60 s before and after the irradiation. The radiation-induced PS was calculated by taking the difference in the pre- and post-irradiation drifts extrapolated to the midpoint of the irradiation. Results were compared to computed doses. Results: Average comparison of calculated ADW values with interferometry-measured values showed an agreement to within 9.5%. k=1 uncertainties were 4.3% for calculations and 14.7% for measurements. The dominant source of uncertainty for the measurements was a temperature drift of about 30 µK/s caused by heat conduction from the interferometer’s surroundings. Conclusion: This work presented the first absolute ADW measurements using interferometry in the dose range of linac-based radiotherapy. Future work to improve measurements’ reproducibility includes the implementation of active thermal control techniques.

60 APPLIED LIFE SCIENCES↗

Holographic superconductors with Horava-Lifshitz black holes

We discuss the phase transition of planar black holes in Horava-Lifshitz gravity by introducing a Maxwell field and a complex scalar field. We calculate the condensate of the charged operators in the dual conformal field theories when the mass square of the complex scalar field is m{sup 2}=-2/L{sup 2} and m{sup 2}=0, respectively. We compute the electrical conductivity of the Horava-Lifshitz superconductor in the probe approximation. In particular, it is found that there exists a spike in the conductivity for the case of the operator with scaling dimension one. These results are quite similar to those in the case of Schwarzschild-AdS black holes, which demonstrates that the holographic superconductivity is a robust phenomenon associated with asymptotic AdS black holes.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Intense Super-radiant X-rays from a Compact Source using a Nanocathode Array and Emittance Exchange

A novel method of producing intense short wavelength radiation from relativistic electrons is described. The electrons are periodically bunched at the wavelength of interest enabling in-phase super-radiant emission that is far more intense than from unbunched electrons. The periodic bunching is achieved in steps beginning with an array of beamlets emitted from a nanoengineered field emission array. The beamlets are then manipulated and converted to a longitudinal density modulation via a transverse to longitudinal emittance exchange. Periodic bunching at short wavelength is shown to be possible, and the partially coherent x-ray properties produced by Inverse Compton scattering from an intense laser are estimated. The proposed method increases the efficiency of x-ray production by several orders of magnitude, potentially enabling compact x-ray sources to produce brilliance and flux similar to major synchrotron facilities.

43 PARTICLE ACCELERATORS↗

Description of the giant monopole resonance in the even-A {sup 112-124}Sn isotopes within a microscopic model including quasiparticle-phonon coupling

We have calculated the strength distributions of the isoscalar giant monopole resonance (ISGMR) in the even-A tin isotopes (A=112-124) that were recently measured in inelastic {alpha} scattering. The calculations were performed within two microscopic models: the quasiparticle random phase approximation (QRPA) and the quasiparticle time blocking approximation (QTBA), which is an extension of the QRPA including quasiparticle-phonon coupling. We used a self-consistent calculational scheme based on the Hartree-Fock+Bardeen-Cooper-Schrieffer approximation. Within the RPA the self-consistency is full. The single-particle continuum is also exactly included at the RPA level. The self-consistent mean field and the effective interaction are derived from the Skyrme energy functional. In the calculations, two Skyrme force parametrizations were used: T5 with a comparatively low value of the incompressibility modulus of infinite nuclear matter (K{sub {infinity}}=202 MeV) and T6 with K{sub {infinity}}=236 MeV. The T5 parametrization gives theoretical results for tin isotopes in good agreement with the experimental data including the resonance widths. The results of the ISGMR calculations in {sup 90}Zr, {sup 144}Sm, and {sup 208}Pb performed with these Skyrme forces are discussed and compared with the experiment.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

SU-E-T-142: Effect of the Bone Heterogeneity On the Unflattened and Flattened Photon Beam Dosimetry: A Monte Carlo Comparison

Purpose: This study compared the dependence of depth dose on bone heterogeneity of unflattened photon beams to that of flattened beams. Monte Carlo simulations (the EGSnrc-based codes) were used to calculate depth doses in phantom with a bone layer in the buildup region of the 6 MV photon beams. Methods: Heterogeneous phantom containing a bone layer of 2 cm thick at a depth of 1 cm in water was irradiated by the unflattened and flattened 6 MV photon beams (field size = 10×10 cm{sup 2}). Phase-space files of the photon beams based on the Varian TrueBeam linac were generated by the Geant4 and BEAMnrc codes, and verified by measurements. Depth doses were calculated using the DOSXYZnrc code with beam angles set to 0° and 30°. For dosimetric comparison, the above simulations were repeated in a water phantom using the same beam geometry with the bone layer replaced by water. Results: Our results showed that the beam output of unflattened photon beams was about 2.1 times larger than the flattened beams in water. Comparing the water phantom to the bone phantom, larger doses were found in water above and below the bone layer for both the unflattened and flattened photon beams. When both beams were turned 30°, the deviation of depth dose between the bone and water phantom became larger compared to that with beam angle equal to 0°. Dose ratio of the unflattened and flattened photon beams showed that the unflattened beam has larger depth dose in the buildup region compared to the flattened beam. Conclusion: Although the unflattened photon beam had different beam output and quality compared to the flattened, dose enhancements due to the bone scatter were found similar. However, we discovered that depth dose deviation due to the presence of bone was sensitive to the beam obliquity.

60 APPLIED LIFE SCIENCES↗