Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83

Anomalous aspects of magnetosheath flow and of the shape and oscillations of the magnetopause during an interval of strongly northward interplanetary magnetic field

On 15 Feb. 1978, the orientation of the interplanetary magnetic field (IMF) remained steadily northward for more than 12 hours. The ISEE 1 and 2 spacecraft were located near apogee on the dawn side flank of the magnetotail. IMP 8 was almost symmetrically located in the magnetosheath on the dusk flank and IMP 7 was upstream in the solar wind. Using plasma and magnetic field data, we show the following: (1) the magnetosheath flow speed on the flanks of the magnetotail steadily exceeded the solar wind speed by 20 percent; (2) surface waves with approximately a 5-min period and very non-sinusoidal waveform were persistently present on the dawn magnetopause and waves of similar period were present in the dusk magnetosheath; and (3) the magnetotail ceased to flare at an antisunward distance of 15 R(sub E). We propose that the acceleration of the magnetosheath flow is achieved by magnetic tension in the draped field configuration for northward IMF and that the reduction of tail flaring is consistent with a decreased amount of open magnetic flux and a larger standoff distance of the subsolar magnetopause. Results of a three-dimensional magnetohydrodynamic simulation support this phenomenological model.

Chen, Sheng-Hsien↗

Analysis of the gas-lubricated flat-sector-pad thrust bearing

A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗

An accurate solution of the gas lubricated, flat sector thrust bearing

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗

Measurements of energy exchange between acoustic fields and non-uniform steady flow fields

Data were obtained for a resonance tube having a vent at the center in the lateral boundary, an average flow being introduced at the ends. Experiments were done for both circular and slot vents, over ranges of both frequency and Mach number. It was demonstrated that a subsonic exhaust vent in the lateral boundary of a cold flow resonance tube provides a gain of acoustic energy for the fundamental mode within the resonance tube. The gain of acoustic energy increases approximately linearly with the Mach number, as predicted by the one-dimensional analysis. The one-dimensional result gives the values for the slope representing the variation of the attenuation coefficient of the exhaust vent with respect to the average Mach number of the flow within roughly 30% of those measured. It has been verified that the subsonic vent produces a gain proportional to the average Mach number, proportional to the frequency, and independent of the shape. The results may be applicable to the study of vibration phenomena in solid propellant rocket engines.

Magiawala, K. R.↗

Structure of the southern Rio Grande rift from gravity interpretation

Regional Bouguer gravity anomalies in southern New Mexico have been analyzed by two-dimensional wave number filtering and poly-nomial trend surface analysis of the observed gravity field. A prominent, regional oval-shaped positive gravity anomaly was found to be associated with the southern Rio Grande rift. Computer modeling of three regional gravity profiles suggests that this anomaly is due to crustal thinning beneath the southern Rio Grande rift. These models indicate a 25 to 26-km minimum crustal thickness within the rift and suggest that the rift is underlain by a broad zone of anomalously low-density upper mantle. The southern terminus of the anomalous zone is approximately 50 km southwest of El Paso, Texas. A thinning of the rifted crust of 2-3 km relative to the adjacent Basin and Range province indicates an extension of about 9 percent during the formation of the modern southern Rio Grande rift. This extension estimate is consistent with estimates from other data sources. The crustal thinning and anomalous mantle is thought to result from magmatic activity related to surface volcanism and high heat flow in this area.

Daggett, P. H.↗

Shape design sensitivity analysis of built-up structures

Selection of the best shape of a fillet in a tension bar such that no yielding occurs has long attracted the attention of engineers. Dimensions and notations for the bar and fillet are shown. With symmetry, only the upper half of the bar is considered. The optimal design problem is to find a boundary shape to minimize the total area of the fillet such that no yielding occurs. The classical boundary value problem is reduced to a variational or energy related problem which not only has excellent properties of existence and uniqueness but also provides the mathematical foundation for finite element analysis. The variational formulation may be viewed as the principle of virtual work and the finite element method as a application of the Galerkin method to the variational equation for approximate solution of the boundary value problem.

Choi, K. K.↗

Fully-coupled analysis of jet mixing problems. Three-dimensional PNS model, SCIP3D

Numerical procedures formulated for the analysis of 3D jet mixing problems, as incorporated in the computer model, SCIP3D, are described. The overall methodology closely parallels that developed in the earlier 2D axisymmetric jet mixing model, SCIPVIS. SCIP3D integrates the 3D parabolized Navier-Stokes (PNS) jet mixing equations, cast in mapped cartesian or cylindrical coordinates, employing the explicit MacCormack Algorithm. A pressure split variant of this algorithm is employed in subsonic regions with a sublayer approximation utilized for treating the streamwise pressure component. SCIP3D contains both the ks and kW turbulence models, and employs a two component mixture approach to treat jet exhausts of arbitrary composition. Specialized grid procedures are used to adjust the grid growth in accordance with the growth of the jet, including a hybrid cartesian/cylindrical grid procedure for rectangular jets which moves the hybrid coordinate origin towards the flow origin as the jet transitions from a rectangular to circular shape. Numerous calculations are presented for rectangular mixing problems, as well as for a variety of basic unit problems exhibiting overall capabilities of SCIP3D.

Wolf, D. E.↗

Meteor stream activity. 2: Meteor outbursts

In the past two centuries, alert amateur and professional meteor astronomers have documented 35 outbursts of 17 individual meteor streams well enough to allow the construction of a homogeneous set of activity curves. These curves add to similar profiles of the annual streams in a previous paper (Paper 1). This paper attempts to define the type and range of phenomena that classify as meteor outbursts from which the following is concluded: Outbursts are associated with the return of the comet to perihelion (near-comet type outbursts), but occur also when the parent comet is far from perihelion and far from the Earth (far-comet type). All outbursts of a given type only, depending on encounter geometry. The activity curves, expressed in terms of Zenith Hourly Rates (ZHR), have a shape that is generally well described by: ZHR = ZHR(sub max) 10(sup(-B (the absolute value of lambda (sub dot in a circle) - lambda (sup max) (sub dot in a circle))). The steepness of the slopes varies from an exponent of B = 7 to B = 220 per degree of solar longitude, with a typical value of B = 30. In addition, most near-comet type outbursts have a broader component underlying the main peak with B approximately 1 - 7.The duration Delta t is approximately 1/B of the main peak is almost independent of location near the comet, while the background component varies considerably in duration and relative intensity from one return to another. The two components in the activity curve are due to two distinct structures in the dust distribution near the parent comet, where the main component can be due to a sheet of dust that emanates from the IRAS dust trail. This brings the total number of distinct structures in meteor streams to four, including the two structures from the annual stream activity in Paper 1.

Jenniskens, P.↗

On automating domain connectivity for overset grids

An alternative method for domain connectivity among systems of overset grids is presented. Reference uniform Cartesian systems of points are used to achieve highly efficient domain connectivity, and form the basis for a future fully automated system. The Cartesian systems are used to approximate body surfaces and to map the computational space of component grids. By exploiting the characteristics of Cartesian systems, Chimera type hole-cutting and identification of donor elements for intergrid boundary points can be carried out very efficiently. The method is tested for a range of geometrically complex multiple-body overset grid systems. A dynamic hole expansion/contraction algorithm is also implemented to obtain optimum domain connectivity; however, it is tested only for geometry of generic shapes.

Chiu, Ing-Tsau↗

Strong scintillations in astrophysics. II - A theory of temporal broadening of pulses

A theory of temporal broadening of pulses propagating in a turbulent medium is developed on the basis of the Markov approximation. The theory may be applied to quite general turbulence spectra and to thin or thick turbulent regions. Since the basis of the theory is the wave equation, no reliance is placed on geometrical optics and no assumptions are made about the scattered angular spectrum. The observed smearing is found to be the combination of three effects: the dispersion effect, the pure refractive effect, and the diffraction effect. The last of these dominates for typical pulsar parameters. Pulse shapes are calculated for both Gaussian and Kolmogorov turbulence spectra and it is shown how these scale with the various turbulence parameters.

Lee, L. C.↗

Collisionless tearing in a field-reversed sheet pinch assuming nonparallel propagation

The problem of collisionless linear tearing is examined assuming a wave vector with a component normal to the equilibrium field. The geometry is defined and the general form of the linear dispersion equation is calculated. The linear theory results when k is parallel to B are reviewed, and Ampere's law is calculated for the external adiabatic region when k times B does not equal zero, using two-fluid theory. A solution is obtained for the approximate form of the perturbed currents and vector potential assuming quasi-parallel k. The resonant current contributions within the singular layer are calculated, obtaining an estimate of the dispersion equation. The form of the adiabatic currents within the singular layer is calculated, showing that an x-z current system persists even in the limit k perpendicular to B goes to zero. Finally, the perturbed vector potential solutions across the singular layer are matched to obtain the shape of the complete eigenfunction.

Quest, K. B.↗

Quantitative observations of the behavior of anomalous low altitude ClO in the Antarctic spring Stratosphere, 1987

During the second National Ozone Expedition ground-based observations at McMurdo Station Antarctica were performed which resulted in a second season's measurement of abnormally large amounts of ClO in the Antarctic spring stratosphere. The original measurements of 1986, in which the presence of this anomalous layer was first discovered, were limited in low altitude recovery of the ClO mixing ratio profile by the restrictions of the spectral bandwidth (256 MHz) which was used to measure the pressure-broadened ClO emission line shape. The 1987 measurements were marked by the use of twice the spectral bandpass employed the previous year, and allow a better characterization of the ClO mixing ratio profile in the critical altitude range 18 to 25 km. In-situ aircraft measurements of ClO made over the Palmer Peninsula during Aug. and Sept. of 1987 by Anderson, et al. effectively determined the important question of the ClO mixing ratio profile at altitudes inaccessible to our technique, below approximately 18 to 18.5 km. These flights did not penetrate further than 75 deg S, however, (vs 78 deg S for McMurdo) and were thus limited to coverage near the outer boundaries of the region of severest ozone depletion over Antarctica in 1987, did not reach an altitude convincingly above that of the peak mixing ratio for ClO, and were not able to make significant observations of the diurnal variation of ClO. The two techniques, and the body of data recovered by each, thus complement one another in producing a full picture of the anomalous ClO layer intimately connected with the region of Antarctic spring ozone depletion. An analysis is presented of the mixing ratio profile from approximately 18 to 45 km, the diurnal behavior, and the secular change in ClO over McMurdo Station during Sept. and early Oct. 1987.

Dezafra, R. L.↗

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗

Spacecraft design considerations for an Inner Magnetosphere Imager mission

Imaging the Earth's magnetosphere from space will enable scientists to better understand the global shape of the inner magnetosphere, its components and processes. The proposed Inner Magnetosphere Imager (IMI) mission will obtain the first simultaneous images of the component regions of the inner magnetosphere and will enable scientists to relate these global images to internal and external influences as well as local observations. NASA's Marshall Space Flight Center (MSFC) is performing a concept definition study of the proposed mission. As currently envisioned, the baseline mission calls for an instrument complement of approximately seven imagers to be flown in an elliptical Earth orbit with an apogee of seven Earth Radii (RE). Several spacecraft concepts have been examined for the mission. The baseline concept utilizes a spinning spacecraft with a despun platform, the second uses a three-axis stabilized spacecraft with a spinning platform, while the third option splits the instruments onto two small satellites; a spinning spacecraft and a complementary three-axis stabilized spacecraft. This paper will address the mission objectives, the rationale for using proven spacecraft designs, and the preliminary concept definition study team results for all three options.

Herrmann, Melody C.↗

Investigation of a Cermet Gas-turbine-blade Material of Titanium Carbide Infiltrated with Hastalloy C

A cermet composition was investigated as a potential material for gas-turbine blades. Blades of HS-21 alloy were also operated in the engine simultaneously to provide a basis of comparison. The cermet blades survived as long as approximately 312-1/2 hours at about 1500 degrees F with an average midspan centrifugal stress of approximately 11,500 psi. The alloy blade midspan stress was about 15,300 psi. Because of extensive damage to both types of blade due to external causes, a reliable comparison of operating lives could not be made. The cermet blades tended to fail in the airfoil rather than in the base, although the base was the usual location of failure in a prior study of cold-pressed and sintered cermets of other compositions with the same blade shape.

Hoffman, Charles A↗

Modeling and numerical simulation of microwave pulse propagation in air breakdown environment

It is shown that ionization occurs wherever the field intensity of the pulse exceeds the local breakdown threshold field of the background air. The produced plasma then attenuates the pulse and gives rise to a tail erosion phenomenon that plays the primary role in limiting the energy transfer of the pulse from source to destination. A theoretical model describing the propagation of an intense microwave pulse in an air breakdown environment is developed that includes the possible focusing effect introduced by either using phase array antennas or the other arrangements. The self-consistent description of the propagation process is provided by a set of two modal equations. These include a continuity equation (Poynting's equation) for the energy density of the pulse and a rate equation of the electron density. A forward wave approximation is used to simplify Poynting's equation, and a semiempirical formula is used for the ionization frequency, nu(sub i). This frequency provides the coupling between the two modal equations, and is used to express the electron rate equation explicitly. In terms of the relevant parameters of the atmosphere, these two equations are normalized for numerical analysis of pulse propagation in the atmosphere. The dependencies of the propagation characteristics of the pulse on intensity, frequency, width, and shape of the pulse are determined. The numerical simulations lead to a useful empirical relation p(exp 3)w = alpha = constant, where p and w are the incident power and width of the pulse and alpha depends on the percentage of pulse energy transferred from the source point to a destined position. The density distribution of the pulse's self-generated plasma is also evaluated. The results also show that for ionization caused by a single unfocused microwave pulse transmitted upwards from the ground, the maximum electron density produced at, for example, 50 km altitude is limited by the tail erosion effect to below 10(exp 6) cm(exp -3). Repetitive pulse and focused beam approaches are also examined. Both approaches can increase the maximum electron density by no more than an order of magnitude. A scheme using two obliquely propagating pulses intersecting at the destined height, e.g. 50 km, is considered. It is shown that the electron density generated at the lowest intersecting position can easily reach a value of 6.6 x 10(exp 8) cm(exp -3), which is considered to be high enough for artificial ionospheric mirror (AIM) application.

Kim, J.↗

Three-Dimensional Multiscale MHD Model of Cometary Plasma Environments

First results of a three-dimensional multiscale MHD model of the interaction of an expanding cometary atmosphere with the magnetized solar wind are presented. The model starts with a supersonic and super-Alfvenic solar wind far upstream of the comet (25 Gm upstream of the nucleus) with arbitrary interplanetary magnetic field orientation. The solar wind is continuously mass loaded with cometary ions originating from a 10-km size nucleus. The effects of photoionization, electron impact ionization, recombination, and ion-neutral frictional drag are taken into account in the model. The governing equations are solved on an adaptively refined unstructured Cartesian grid using our new multiscale upwind scalar conservation laws-type numerical technique (MUSCL). We have named this the multiscale adaptive upwind scheme for MHD (MAUS-MHD). The combination of the adaptive refinement with the MUSCL-scheme allows the entire cometary atmosphere to be modeled, while still resolving both the shock and the diamagnetic cavity of the comet. The main findings are the following: (1) Mass loading decelerates the solar wind flow upstream of the weak cometary shock wave (M approximately equals 2, M(sub A) approximately equals 2), which forms at a subsolar standoff distance of about 0.35 Gm. (2) A cometary plasma cavity is formed at around 3 x 10(exp 3) km from the nucleus. Inside this cavity the plasma expands outward due to the frictional interaction between ions and neutrals. On the nightside this plasma cavity considerably narrows and a relatively fast and dense cometary plasma beam is ejected into the tail. (3) Inside the plasma cavity a teardrop-shaped inner shock is formed, which is terminated by a Mach disk on the nightside. Only the region inside the inner shock is the 'true' diamagnetic cavity. (4) The model predicts four distinct current systems in the inner coma: the density peak current, the cavity boundary current, the inner shock current, and finally the cross-tail current. (5) The calculated plasma parameters (magnetic field, plasma density, speed, and temperature) are in very good agreement with published Giotto observations.

Gombosi, Tamas I.↗

Control of cytoskeletal mechanics by extracellular matrix, cell shape, and mechanical tension

We have investigated how extracellular matrix (ECM) alters the mechanical properties of the cytoskeleton (CSK). Mechanical stresses were applied to integrin receptors on the apical surfaces of adherent endothelial cells using RGD-coated ferromagnetic microbeads (5.5-microns diameter) in conjunction with a magnetic twisting device. Increasing the number of basal cell-ECM contacts by raising the fibronectin (FN) coating density from 10 to 500 ng/cm2 promoted cell spreading by fivefold and increased CSK stiffness, apparent viscosity, and permanent deformation all by more than twofold, as measured in response to maximal stress (40 dyne/cm2). When the applied stress was increased from 7 to 40 dyne/cm2, the stiffness and apparent viscosity of the CSK increased in parallel, although cell shape, ECM contacts, nor permanent deformation was altered. Application of the same stresses over a lower number ECM contacts using smaller beads (1.4-microns diameter) resulted in decreased CSK stiffness and apparent viscosity, confirming that this technique probes into the depth of the CSK and not just the cortical membrane. When magnetic measurements were carried out using cells whose membranes were disrupted and ATP stores depleted using saponin, CSK stiffness and apparent viscosity were found to rise by approximately 20%, whereas permanent deformation decreased by more than half. Addition of ATP (250 microM) under conditions that promote CSK tension generation in membrane-permeabilized cells resulted in decreases in CSK stiffness and apparent viscosity that could be detected within 2 min after ATP addition, before any measurable change in cell size.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗