Search NASA⌕ Search

SEARCH · Search NASA

Results for “structure engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Interconnected ionic domains enhance conductivity in microphase separated block copolymer electrolytes

Block copolymer electrolytes (BCEs) represent an attractive choice as solid-state ionic conductors for electrochemical technologies used in energy storage and conversion, water treatment, sensors, and data storage and processing. Unlocking the maximum ionic conductivity of BCEs requires an intimate understanding as to how the microphase separated structure influences transport properties. However, elucidating such knowledge remains elusive due to the challenging task of precisely engineering BCEs with a defined structure in bulk materials. In this work, we examined BCEs in a thin film format because it was amenable to attaining BCEs with a desired nanostructure. Specifically, we systematically investigated anion-conducting BCEs with different degrees of connectivity of the ionic domains. For the first time, we demonstrate that increasing terminal defects in the ionic domain from 1 terminal defect per mu m(2) to 20 terminal defects per mu m(2) ( a relatively small amount of defects) decreased ionic conductivity by 67% compared to the maximum value attained. Conversely, maximizing ionic domain connectivity increased the ionic conductivity by two-fold over a non-ordered BCE film. These experiments highlight that microphase separation alone was insufficient for ameliorating ionic conductivity in BCEs. Rather, microphase separation coupled with complete ionic domain connectivity realized BCEs with significantly enhanced ionic conductivity.

Arges, Christopher G. (ORCID:0000000317038323)↗
DOE OSTI2026

Twist-Angle-Dependent Excitons in Moiré MoTe 2 Visualized by Cryogenic STEM and Monochromated EELS

van der Waals twisted bilayers of transition-metal dichalcogenides exhibit diverse excitonic phenomena arising from moiré superlattices and lattice reconstruction. While interlayer strain and relaxation reshape their electronic bands, their nanoscale influence on the excitonic fine structure remains poorly understood. Here, we study the interplay between spin–orbit coupling (SOC) and the moiré lattice by probing excitons in H-type twisted (∼8-layer × 8-layer) MoTe 2 using atomic-resolution scanning transmission electron microscopy (STEM) combined with monochromated electron energy loss spectroscopy (EELS) at cryogenic temperature. Spatially resolved spectra reveal moiré-site-dependent variations in excitonic absorption, including modulation of the X B exciton across the moiré unit cell. We find that SOC in MoTe 2 increases with the twist angle within the studied range (2–4.5°), with the largest value observed at 4°. Furthermore, these findings establish the twist angle as a tunable parameter for SOC via moiré engineering and link local structural relaxation to excitonic fine structure in twisted MoTe 2 .

cryogenic STEM/EELS↗
DOE OSTI2021

Test Results of a High-Gradient 2.856-GHz Negative Harmonic Accelerating Waveguide

We report the high-gradient tests results of a novel traveling wave accelerating structure for β=0.3 based on a novel approach of operating at the first negative spatial harmonic. Accelerating gradients of 50 MV/m and peak electric fields of 160 MV/m were achieved in a single structure consisting of 15 coupled cells during tests at the advanced photon source. This work was performed by RadiaBeam, in collaboration with the Argonne National Laboratory, as a part of a Research and Development Program for the development of an ultrahigh-gradient linear accelerator, the Advanced Compact Carbon Ion Linac, for hadron therapy.

42 ENGINEERING↗
NASA NTRS2002

Multidisciplinary Analysis of a Hypersonic Engine

This paper describes implementation of a technique used to obtain a high fidelity fluid-thermal-structural solution of a combined cycle engine at its scram design point. Single-discipline simulations are insufficient here since interactions from other disciplines are significant. Using off-the-shelf, validated solvers for the fluid, chemistry, thermal, and structural solutions, this approach couples together their results to obtain consistent solutions.

Stewart, M. E. M.↗
DOE OSTI2022

Novel and effective surface passivation for high efficiency n- and p-type Silicon solar cell

The project objective was to develop a novel Si surface passivation method using chalcogens, sulfur (S) and/or selenium (Se), as passivating elements, to withstand industry-standard high temperature contacting and metallization schemes for p-type Si based passivated emitter and rear contact (p-PERC) solar cells. The back surface passivation of PERC cells has been improved drastically with the invention and successful application of an Al 2 O 3 passivation layer. However, the front n + diffused junction surface is still poorly passivated by the standard amorphous silicon nitride (SiNx) anti-reflection coating (ARC) layer. This project sought to address the passivation challenges of both front n+ emitter and undiffused p-Si back surface. Improved p-PERC solar cell performance with open circuit voltage (V OC ) > 680 mV and efficiency of 22% were targeted to validate superior defect passivation properties as compared to standard SiO 2 / Al 2 O 3 passivation. During this project, we systematically investigated process-structure-properties-performance relationships of this novel advanced defect passivation approach. The S/Se passivation was carried out by reacting industrial Czochralski (Cz) Si wafers in H 2 S and H 2 Se gases in a chemical vapor deposition (CVD) reactor at temperatures up to 700°C. After an exhaustive optimization of the process parameters (temperature, time, and gas concentration), we established an optimized process and demonstrated extremely low surface recombination velocities (SRVs) of 1.5 cm/s and 8 cm/s on n-type and p-type Si, respectively, by S-passivation. In-depth surface and interface characterization were performed using soft x-ray and photoelectron spectroscopies (XPS, UPS, XES), combined with capacitance-voltage-frequency (C-V-f) measurements, to decipher the surface chemical/electronic structure and interface defect state densities. These measurements provided critical understanding of the defect passivation mechanism and elucidated the presence of surface S-Si bonds, a reduction of surface dipoles, and low interface state densities (D it ) < 10 11 cm -2 ev -1 . We also found that the Se-passivation is inferior to the S-passivation (by at least one order of magnitude in SRV). Application of the optimized S-passivation to the n+ diffused emitter surface led to a low surface recombination current density, J0 ≈ 40 fA/cm 2 (~ 1/4 of the industry-standard SiNx-passivation), and high implied V OC (686 mV) in p-PERC solar cell structures. The S-passivation process also was found to improve the bulk quality of the p-type Si, better than the SiO 2 or Al 2 O 3 passivation processes. After successful demonstration of efficient passivation of Si surface defects by S, we extensively studied the air, thermal, and illumination stability of the passivation structure. S-passivation itself degrades in air due to competing reactions with moisture and oxygen to form oxides, which can be eliminated by a SiNx capping layer (also acting as a anti-reflective coating). After SiNx process optimization, we demonstrated illumination and thermally stable S-passivation with SRV < 5 cm/s and J 0 < 80 fA/cm 2 . These enhancements in Si passivation, incorporated into p-PERC cells, achieved an efficiency of 19.93% with V OC = 649 mV, using manufacturing metallization and contacting schemes. The low cell performance (cell V OC is much less than the implied V OC = 686 mV, anticipated from surface passivation) was identified due to degradation of S-passivation during the metal firing step (out-diffusion of S from the Si interface to the SiNx surface). The S-passivation of Si surfaces shows significant promise with excellent passivation quality, essential for high performance (high V OC , high efficiency) solar cells. Integration of this innovative defect passivation into devices, however, demands further development of the capping layer, low temperature (<700°C) metallization process, and/or engineering of advanced device structures. Surface passivation-dominated advanced Si solar cells, such as tunnel oxide passivated contacts and Si heterojunctions, are increasingly of interest due to their high-performance potential and will have a growing photovoltaic market share in the near future.

14 SOLAR ENERGY↗
NASA NTRS1977

Integrated gas turbine engine-nacelle

A nacelle for use with a gas turbine engine is presented. An integral webbed structure resembling a spoked wheel for rigidly interconnecting the nacelle and engine, provides lightweight support. The inner surface of the nacelle defines the outer limits of the engine motive fluid flow annulus while the outer surface of the nacelle defines a streamlined envelope for the engine.

Adamson, A. P.↗
NASA NTRS1998

A Geometry Based Infra-Structure for Computational Analysis and Design

The computational steps traditionally taken for most engineering analysis suites (computational fluid dynamics (CFD), structural analysis, heat transfer and etc.) are: (1) Surface Generation -- usually by employing a Computer Assisted Design (CAD) system; (2) Grid Generation -- preparing the volume for the simulation; (3) Flow Solver -- producing the results at the specified operational point; (4) Post-processing Visualization -- interactively attempting to understand the results. For structural analysis, integrated systems can be obtained from a number of commercial vendors. These vendors couple directly to a number of CAD systems and are executed from within the CAD Graphical User Interface (GUI). It should be noted that the structural analysis problem is more tractable than CFD; there are fewer mesh topologies used and the grids are not as fine (this problem space does not have the length scaling issues of fluids). For CFD, these steps have worked well in the past for simple steady-state simulations at the expense of much user interaction. The data was transmitted between phases via files. In most cases, the output from a CAD system could go to Initial Graphics Exchange Specification (IGES) or Standard Exchange Program (STEP) files. The output from Grid Generators and Solvers do not really have standards though there are a couple of file formats that can be used for a subset of the gridding (i.e. PLOT3D data formats). The user would have to patch up the data or translate from one format to another to move to the next step. Sometimes this could take days. Specifically the problems with this procedure are:(1) File based -- Information flows from one step to the next via data files with formats specified for that procedure. File standards, when they exist, are wholly inadequate. For example, geometry from CAD systems (transmitted via IGES files) is defined as disjoint surfaces and curves (as well as masses of other information of no interest for the Grid Generator). This is particularly onerous for modern CAD systems based on solid modeling. The part was a proper solid and in the translation to IGES has lost this important characteristic. STEP is another standard for CAD data that exists and supports the concept of a solid. The problem with STEP is that a solid modeling geometry kernel is required to query and manipulate the data within this type of file. (2) 'Good' Geometry. A bottleneck in getting results from a solver is the construction of proper geometry to be fed to the grid generator. With 'good' geometry a grid can be constructed in tens of minutes (even with a complex configuration) using unstructured techniques. Adroit multi-block methods are not far behind. This means that a million node steady-state solution can be computed on the order of hours (using current high performance computers) starting from this 'good' geometry. Unfortunately, the geometry usually transmitted from the CAD system is not 'good' in the grid generator sense. The grid generator needs smooth closed solid geometry. It can take a week (or more) of interaction with the CAD output (sometimes by hand) before the process can begin. One way Communication. (3) One-way Communication -- All information travels on from one phase to the next. This makes procedures like node adaptation difficult when attempting to add or move nodes that sit on bounding surfaces (when the actual surface data has been lost after the grid generation phase). Until this process can be automated, more complex problems such as multi-disciplinary analysis or using the above procedure for design becomes prohibitive. There is also no way to easily deal with this system in a modular manner. One can only replace the grid generator, for example, if the software reads and writes the same files. Instead of the serial approach to analysis as described above, CAPRI takes a geometry centric approach. This makes the actual geometry (not a discretized version) accessible to all phases of the analysis. The connection to the geometry is made through an Application Programming Interface (API) and NOT a file system. This API isolates the top-level applications (grid generators, solvers and visualization components) from the geometry engine. Also this allows the replacement of one geometry kernel with another, without effecting these top-level applications. For example, if UniGraphics is used as the CAD package then Parasolid (UG's own geometry engine) can be used for all geometric queries so that no solid geometry information is lost in a translation. This is much better than STEP because when the data is queried, the same software is executed as used in the CAD system. Therefore, one analyzes the exact part that is in the CAD system. CAPRI uses the same idea as the commercial structural analysis codes but does not specify control. Software components of the CAD system are used, but the analysis suite, not the CAD operator, specifies the control of the software session. This also means that the license issues (may be) minimized and individuals need not have to know how to operate a CAD system in order to run the suite.

Haimes, Robert↗
NASA NTRS1978

Thermal-structural design study of an airframe-integrated Scramjet

Design concepts are developed and evaluated for a cooled structures assembly for the Scramjet engine, for engine subsystems mass, volume, and operating requirements, and for the aircraft/engine interface. A thermal protection system was defined that makes it possible to attain a life of 100 hours and 1000 cycles. The coolant equivalence ratio at the Mach 10 maximum thermal loading condition is 0.6, indicating a capacity for airframe cooling. The mechanical design is feasible for manufacture using conventional materials. For the cooled structures in a six-module engine, the mass per unit capture area is 12.4 KN/sq m. The total weight of a six-module engine assembly including the fuel system is 14.73 KN.

Killackey, J. J.↗
DOE OSTI2022

Q-dependent collective relaxation dynamics of glass-forming liquid Ca0.4K0.6(NO3)1.4 investigated by wide-angle neutron spin-echo

Abstract The relaxation behavior of glass formers exhibits spatial heterogeneity and dramatically changes upon cooling towards the glass transition. However, the underlying mechanisms of the dynamics at different microscopic length scales are not fully understood. Employing the recently developed wide-angle neutron spin-echo spectroscopy technique, we measured the Q -dependent coherent intermediate scattering function of a prototypical ionic glass former Ca 0.4 K 0.6 (NO 3 ) 1.4 , in the highly viscous liquid state. In contrast to the structure modulated dynamics for Q < 2.4 Å −1 , i.e., at and below the structure factor main peak, for Q > 2.4 Å −1 , beyond the first minimum above the structure factor main peak, the stretching exponent exhibits no temperature dependence and concomitantly the relaxation time shows smaller deviations from Arrhenius behavior. This finding indicates a change in the dominant relaxation mechanisms around a characteristic length of 2π/(2.4 Å −1 ) ≈ 2.6 Å, below which the relaxation process exhibits a temperature independent distribution and more Arrhenius-like behavior.

42 ENGINEERING↗
DOE OSTI2023

Tailoring Growth Interfaces of Virtual Substrates for Power Electronics

Power electronics materials are poised to play a critical role in fulfilling next generation energy needs, with up to 90% of future energy demand predicted to flow through power electronics at some point.[1] Among a number of candidate materials, AlxGa1-xN is the strongest, having bipolar dopability, thermal and chemical stability, an ultra-wide bandgap, and demonstrated experimental feasibility. However, AlGaN growth is limited by a lack of lattice-matched substrates, ultimately stunting material quality at higher thicknesses needed for power electronics applications. Further, high power applications increasingly call for fully vertical device structures, necessitating a conductive substrate. [1] Recently our group identified the (111) plane of TaC as a conductive surface lattice-matched to Al0.55Ga0.45N, taking inspiration from prior work of AlN and GaN binaries on carbide and boride substrates. [2,3,4] In this talk we demonstrate the growth of (111)-oriented TaC by RF sputtering. We investigate the interface of TaC with sapphire and SiC substrates and identify means to suppress competing Ta2C nucleation in order to stabilize (111)-oriented TaC. Potential stacking sequences are identified with respect to crystal structure and observed twinning in the TaC films. We next assess structural changes and film recrystallization that results from face-to-face annealing of TaC thin films at high temperatures above 1500 degrees Celsius. Changes to grain structure and domain size are assessed by x-ray diffraction and surface morphology is explored using atomic force microscopy. Figure 1 shows significant improvements to in- and out-of-plane strain following annealing along with the formation of terraced step edges at the film surface. Strain as a function of material composition and thickness is considered, as this may play a major role in future nucleation of AlGaN layers.

CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND SU↗
NASA NTRS1987

STA-2A NDT testing

The nondestructive testing (NDT) on the Space Shuttle Solid Rocket Booster (SRB) filament wound case (FWC) short stact structural test articles 2 (STA-2A) during test of phases 1B-9C is described. The primary objective of this testing was to verify the structural integrity of the SRB-FWC for critical design loads. Another objective was to quantify the effect of load distributions in the aft skirt. The NDT objectives were to determine the acoustic emission characteristics of the FWC-SRB and to identify possible design deficiencies or defect growth. The results from the posttest inspection of the samples shows the depth measurements taken were accurate until exceeding .260 inches thickness. The data then show that pulse echo measurements exceeded actual part thickness by 10 to 14 percent. The mapping of forward boundaries of delaminations proved to be within the tolerance of the equipment. Using the ZIP probe, the maximum difference between the pulse echo boundary and the visual boundary was expected to be no greater than one half the diameter of the probe. The NDT performance on STA-2A shows how NDT can be used to assist design engineering in evaluating the structural integrity of composite test articles.

Lewis, T. J.↗
DOE OSTI2017

Novel Pd 2 Se 3 Two-Dimensional Phase Driven by Interlayer Fusion in Layered PdSe 2

Two-dimensional (2D) materials are easily fabricated when their bulk form has a layered structure. The monolayer form in layered transition-metal dichalcogenides is typically the same as a single layer of the bulk material. Yet, PdSe 2 presents a puzzle. Its monolayer form has been theoretically shown to be stable, but there have been no reports that monolayer PdSe 2 has been fabricated. Here, combining atomic-scale imaging in a scanning transmission electron microscope and density functional theory, we show that the preferred monolayer form of this material amounts to a melding of two bulk monolayers accompanied by the emission of Se atoms so that the resulting stoichiometry is Pd 2 Se 3 . We further verify the interlayer melding mechanism by creating Se vacancies in situ in the layered PdSe 2 matrix using electron irradiation. The discovery that strong interlayer interactions can be induced by defects and lead to the formation of new 2D materials opens a new venue for the exploration of defect engineering and novel 2D structures.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Crashworthy airframe design concepts: Fabrication and testing

Crashworthy floor concepts applicable to general aviation aircraft metal airframe structures were investigated. Initially several energy absorbing lower fuselage structure concepts were evaluated. Full scale floor sections representative of a twin engine, general aviation airplane lower fuselage structure were designed and fabricated. The floors featured an upper high strength platform with an energy absorbing, crushable structure underneath. Eighteen floors were fabricated that incorporated five different crushable subfloor concepts. The floors were then evaluated through static and dynamic testing. Computer programs NASTRAN and KRASH were used for the static and dynamic analysis of the floor section designs. Two twin engine airplane fuselages were modified to incorporate the most promising crashworthy floor sections for test evaluation.

Cronkhite, J. D.↗
NASA NTRS2011

Lightweight, Ultra-High-Temperature, CMC-Lined Carbon/Carbon Structures

Carbon/carbon (C/C) is an established engineering material used extensively in aerospace. The beneficial properties of C/C include high strength, low density, and toughness. Its shortcoming is its limited usability at temperatures higher than the oxidation temperature of carbon . approximately 400 C. Ceramic matrix composites (CMCs) are used instead, but carry a weight penalty. Combining a thin laminate of CMC to a bulk structure of C/C retains all of the benefits of C/C with the high temperature oxidizing environment usability of CMCs. Ultramet demonstrated the feasibility of combining the light weight of C/C composites with the oxidation resistance of zirconium carbide (ZrC) and zirconium- silicon carbide (Zr-Si-C) CMCs in a unique system composed of a C/C primary structure with an integral CMC liner with temperature capability up to 4,200 F (.2,315 C). The system effectively bridged the gap in weight and performance between coated C/C and bulk CMCs. Fabrication was demonstrated through an innovative variant of Ultramet fs rapid, pressureless melt infiltration processing technology. The fully developed material system has strength that is comparable with that of C/C, lower density than Cf/SiC, and ultra-high-temperature oxidation stability. Application of the reinforced ceramic casing to a predominantly C/C structure creates a highly innovative material with the potential to achieve the long-sought goal of long-term, cyclic high-temperature use of C/C in an oxidizing environment. The C/C substructure provided most of the mechanical integrity, and the CMC strengths achieved appeared to be sufficient to allow the CMC to perform its primary function of protecting the C/C. Nozzle extension components were fabricated and successfully hot-fire tested. Test results showed good thermochemical and thermomechanical stability of the CMC, as well as excellent interfacial bonding between the CMC liner and the underlying C/C structure. In particular, hafnium-containing CMCs on C/C were shown to perform well at temperatures exceeding 3,500 F (.1,925 C). The melt-infiltrated CMC-lined C/C composites offered a lower density than Cf/SiC. The melt-infiltrated composites offer greater use temperature than Cf/SiC because of the more refractory ceramic matrices and the C/C substructure provides greater high-temperature strength. The progress made in this work will allow multiple high-temperature components used in oxidizing environments to take advantage of the low density and high strength of C/C combined with the high-temperature oxidation resistance of melt-infiltrated CMCs.

Wright, Matthew J.↗
DOE OSTI2019

Unusual size effects from tilted twin boundaries in nano-twinned metals

Tilted twin boundaries (TBs), whose plane normals are rotated at an angle from the parent grain axis, naturally occur in columnar-grained, nano-twinned (NT) metals. Here, using a combination of atomistic simulations and analytical modeling, we reveal that NT metals with the ideal, non-tilted TBs exhibit continuously increasing strength with decreasing twin thickness, and hence, no inverse twin thickness size effect on strength. In contrast, NT metals with tilted TBs exhibit an inverse size effect, and the critical twin thickness, below which strength decreases, increases as the TB-tilt angle increases. The analysis also identifies a critical value of TB tilt, for which strength becomes independent of twin thickness and is the weakest. The transition arises from a change in dislocation activity prevailing mostly on planes inclined to TBs to planes parallel to the TBs. Overall, these findings reveal a profound influence of TB tilt angle that could redirect the analysis and engineering of nano-twin structures.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Aircraft Turbine Engine Control Research at NASA Glenn Research Center

This paper provides an overview of the aircraft turbine engine control research at the NASA Glenn Research Center (GRC). A brief introduction to the engine control problem is first provided with a description of the state-of-the-art control law structure. A historical aspect of engine control development since the 1940s is then provided with a special emphasis on the contributions of GRC. With the increased emphasis on aircraft safety, enhanced performance, and affordability, as well as the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Branch (CDB) at GRC is leading and participating in various projects to develop advanced propulsion controls and diagnostics technologies that will help meet the challenging goals of NASA Aeronautics Research Mission programs. The rest of the paper provides an overview of the various CDB technology development activities in aircraft engine control and diagnostics, both current and some accomplished in the recent past. The motivation for each of the research efforts, the research approach, technical challenges, and the key progress to date are summarized.

Garg, Sanjay↗
NASA NTRS1993

Nonlinear dynamic simulation of single- and multi-spool core engines

In this paper a new computational method for accurate simulation of the nonlinear dynamic behavior of single- and multi-spool core engines, turbofan engines, and power generation gas turbine engines is presented. In order to perform the simulation, a modularly structured computer code has been developed which includes individual mathematical modules representing various engine components. The generic structure of the code enables the dynamic simulation of arbitrary engine configurations ranging from single-spool thrust generation to multi-spool thrust/power generation engines under adverse dynamic operating conditions. For precise simulation of turbine and compressor components, row-by-row calculation procedures were implemented that account for the specific turbine and compressor cascade and blade geometry and characteristics. The dynamic behavior of the subject engine is calculated by solving a number of systems of partial differential equations, which describe the unsteady behavior of the individual components. In order to ensure the capability, accuracy, robustness, and reliability of the code, comprehensive critical performance assessment and validation tests were performed. As representatives, three different transient cases with single- and multi-spool thrust and power generation engines were simulated. The transient cases range from operating with a prescribed fuel schedule, to extreme load changes, to generator and turbine shut down.

Schobeiri, T.↗
DOE OSTI2023

ECAR-6576 Rev 0 MARVEL Secondary Support Structure Analysis

The Microreactor Applications Research Validation and Evaluation (MARVEL) microreactor generates electricity using four Stirling cycle engines. Each Stirling engine, along with its mounting system, is called a Secondary Support Structure (SSS). An individual SSS consists of a Secondary Output Structure (SOS), a Secondary Support Structure Base, an insulation block, and assorted hardware. The SOS consists of the Stirling engine, the Secondary Output Structure Ring, a vibration isolator, and hardware. The purpose of this analysis is to show that the SSS is appropriately designed to meet structural, mechanical, and maintenance requirements for specified operating conditions.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗