Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffraction optics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

HiRES - High Resolution Extreme Ultraviolet Spectroheliometer toroidal diffraction grating performance evaluation

The ray-tracing results presented characterize the theoretically achievable EUV performance of the HiRES instrument. The effects of optical system misalignment on spectrograph images, and the laboratory results for two f/15 toroidal diffraction gratings that employ a multianode microchannel array, are also presented. Interferometric studies of toroidal figure accuracy, as well as optical and electron microscopy investigations of surface quality, are discussed. While the current toroidal gratings are noted to furnish good imaging across a wide wavelength range, they exhibit excessive EUV scatter, as well as spectral ghosting.

Berger, Thomas E.↗

Structural and Mechanical Properties of Zr-Si-N Coatings Deposited by Arc Evaporation at Different Substrate Bias Voltages

ZrN and Zr-Si-N coatings were formed using vacuum-arc plasma fluxes deposition system at the substrate bias voltage (U{sub B}) ranged from − 50 to − 220 V on HS6-5-2 steel substrates. The structural, mechanical and tribological properties were characterized using x-ray diffraction, atomic force microscopy, scanning electron microscopy, optical microscopy, nanoindentation and ball-on-disk test. The surface roughness parameter Ra of ZrN coatings is lower than Zr-Si-N coatings. Both roughness Ra of Zr-Si-N coatings and the number of surface defects with mainly small dimensions to 1 µm decrease with increasing negative substrate bias voltage. The addition of silicon to ZrN significantly reduces the crystallite size, from about 18.3 nm for ZrN coating to 6.4 nm for Zr-Si-N coating both deposited at the same U{sub B} = − 100 V and 7.8 nm for U{sub B} = − 150 V. The hardness of Zr-Si-N coatings increases to about 30 GPa with the increase in negative substrate bias voltage (U{sub B} = − 220 V). Adhesion of the coatings tested is high, and critical load is above 80 N and reduces with U{sub B} increase. Coefficient of friction determined using AFM shows similar trend as surface roughness in microscale.

36 MATERIALS SCIENCE↗

Diffraction by a perfectly conducting rectangular cylinder which is illuminated by an array of line sources

The geometrical theory of diffraction (GTD) is employed to analyze the radiation from a perfectly-conducting rectangular cylinder illuminated by an array of line sources. The excitation of the cylinder by a single electric or magnetic current line source is considered first, and a solution which includes contributions from the geometrical optics rays and all singly- and doubly-diffracted rays is obtained. A new diffraction coefficient valid in the transition regions of the shadow and reflection boundaries is employed to obtain a continuous total field, except for negligible discontinuities in the doubly-diffracted field at its shadow boundaries. Patterns calculated by the GTD method are found to be in excellent agreement with those calculated from an integral equation formulation. Using superposition the solution for array or aperture excitation of the rectangular cylinder is obtained. A computer program for this solution is included.

Kouyoumjian, R. G.↗

A comparison between using incoherent or coherent sources to align and test an adaptive optical telescope

The concept in the initial alignment of the segmented mirror adaptive optics telescope called the phased array mirror extendable large aperture telescope (Pamela) is to produce an optical transfer function (OTF) which closely approximates the diffraction limited value which would correspond to a system pupil function that is unity over the aperture and zero outside. There are differences in the theory of intensity measurements between coherent and incoherent radiation. As a result, some of the classical quantities which describe the performance of an optical system for incoherent radiation can not be defined for a coherent field. The most important quantity describing the quality of an optical system is the OTF and for a coherent source the OTF is not defined. Instead a coherent transfer function (CTF) is defined. The main conclusion of the paper is that an incoherent collimated source and not a collimated laser source is preferred to calibrate the Hartmann wavefront sensor (WFS) of an aligned adaptive optical system. A distant laser source can be used with minimum problems to correct the system for atmospheric turbulence. The collimation of the HeNe laser alignment source can be improved by using a very small pin hole in the spatial filter so only the central portion of the beam is transmitted and the beam from the filter is nearly constant in amplitude. The size of this pin hole will be limited by the sensitivity of the lateral effect diode (LEDD) elements.

Anderson, Richard↗

DSC and optical studies on BaO-Li{sub 2}O-B{sub 2}O{sub 3}-CuO glass system

Glasses with composition 15BaO-25Li{sub 2}O-(60-x)B{sub 2}O{sub 3} -xCuO (x= 0, 0.2, 0.4, 0.6, 0.8 and 1 mol%) were prepared by the conventional melt quenching technique. These glasses were characterized using X-ray diffraction (XRD), differential scanning calorimetry (DSC) and density measurements. Optical absorption studies were carried out as a function of copper ion concentration. The optical absorption spectra of studied glasses containing copper oxide exhibit a single broad band around 761nm which has been assigned to the 2B{sub 1g}→2B{sub 2g} transition. From these studies, the variations in the values of glass transition temperature (T{sub g}) have been observed. The fundamental absorption edge has been determined from the optical absorption spectra. The values of optical band gap and Urbach energy were determined with increase in concentration of CuO. The variations in density, glass transition temperature, optical band gap and Urbach energy with CuO content have been discussed in terms of changes in the glass structure. The analysis of these results indicated that copper ions mostly exist in Cu{sup 2+} state in these glasses when the concentration of CuO ≤ 0.8 mol% and above this concentration copper ions seem to subsist in Cu{sup 1+} state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hot Deformation Behavior and Microstructural Evolution of Antibacterial Austenitic Stainless Steel Containing 3.60% Cu

Hot deformation behavior of as-cast antibacterial austenitic stainless steel containing 3.60% copper was investigated in a temperature range of 900-1150 °C and strain rate range of 0.01-20 s{sup −1}. At strain rates higher than 1 s {sup −1}, the flow stress curves were corrected considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of steel was 376.02 kJ mol{sup −1}. The microstructural evolution under different temperatures was observed by optical microscopy. The nucleation sites for recrystallization and different orientations and twin ratios under different strain rates were analyzed by electron backscatter diffraction. The results showed that hot deformation was dominated by continuous dynamic recrystallization in the high-temperature and high-strain-rate region (1050-1150 °C, 1-20 s{sup −1}). On increasing the temperature and strain rate, the degree of recrystallization and twinning increased simultaneously. These phenomena promoted one another. Thus, the volume fraction of the recrystallized and twinned grains increased with the addition of Cu.

36 MATERIALS SCIENCE↗

Synthesis and characteristic of self-assembled diamond/copper nanocomposites

Nanodiamond (ND) supported metal oxide or metal catalysts exhibit excellent catalytic activity. ND/Cu nanocomposites and Cu nanoparticles were prepared by reducing Cu(NO{sub 3}){sub 2} in reverses micelle solution. Products were analyzed by X-ray diffraction (XRD), electron paramagnetic resonance (EPR) spectra, UV-vis optical characteristic and transmission electron microscopy (TEM). From the point of nucleation and grow of crystal, ND contributed to heterogeneous nucleation of Cu nanocrystal. The reactive mechanism was explored based on theory of free energy. The formation of resultant self-assembled structures was explained through diffusion-limited aggregation model and Marangoni effect. Both Cu and ND/Cu nanoparticles were strong catalysts on decomposition of NH{sub 4}ClO{sub 4} (AP), and ND/Cu is more effective.

36 MATERIALS SCIENCE↗

Physics-Based Optical Neuromorphic Classification

Typical approaches to classify scenes from light convert the light field to electrons to perform the computation in the digital electronic domain. This conversion and downstream computational analysis require significant power and time. Diffractive neural networks have recently emerged as unique systems to classify optical fields at lower energy and high speeds. Previous work has shown that a single layer of diffractive metamaterial can achieve high performance on classification tasks. In analogy with electronic neural networks, it is anticipated that multilayer diffractive systems would provide better performance, but the fundamental reasons for the potential improvement have not been established. In this work, we present extensive computational simulations of two - layer diffractive neural networks and show that they can achieve high performance with fewer diffractive features than single layer systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optical and structural characterization of GaN thin films at different N to Ga flux ratios

GaN films were grown on Si(111) substrates under various beam equivalent pressure (BEP) ratios by plasma-assisted molecular beam epitaxy. The optical properties for the grown samples were studied over a wide spectral range from 200 to 3300 nm using the reflectance spectrum only. It was found that increasing the N/Ga BEP ratio from 17.9 to 46.1 increases the refractive index (n) from 2.05 to 2.38 at wavelength 630 nm (for example), while the optical energy gap (E{sub g}) were found to be in the range between 3.325 to 3.35 eV with no specific trend. The structural properties for the grown films were studied through two types of rocking curve measurements; normal rocking curve ({omega}-scan) and triple axis rocking curve ({omega}/2{theta}-scan). It was found that with decreasing the N/Ga ratio from 46.1 to 17.9 the full width at half maximum decreases from 0.62 deg. to 0.58 deg. for {omega}-scan and from 0.022 deg. to 0.021 deg. for {omega}/2{theta}-scan. Thus, our results showed a clear correlation between the optical-structural parameters and the BEP ratios of N and Ga.

36 MATERIALS SCIENCE↗

Effect of thermomechanical processing on the microstructure and retained austenite stability during in situ tensile testing using synchrotron x-ray diffraction of NbMoAI TRIP steel.

In this work we compare and contrast the stability of retained austenite during tensile testing of Nb-Mo-Al transformation-induced plasticity steel subjected to different thermomechanical processing schedules. The obtained microstructures were characterised using optical metallography, transmission electron microscopy and X-ray diffraction. The transformation of retained austenite to martensite under tensile loading was observed by in-situ high energy X-ray diffraction at 1ID / APS. It has been shown that the variations in the microstructure of the steel, such as volume fractions of present phases, their morphology and dimensions, play a critical role in the strain-induced transition of retained austenite to martensite.

36 MATERIALS SCIENCE↗

Structure-functional property relationships in rf-sputtered vanadium dioxide thin films

The study of metal-insulator transition (MIT) in VO{sub 2} thin films synthesized by means of rf sputtering from a VO{sub 2} target is presented. A comparison with conventional reactive sputtering from a V target is also given. Detailed x-ray diffraction analysis, electrical resistance switching, and infrared optical reflectance measurements confirm that our sputtering technique yields high-quality VO{sub 2} films. We discuss in depth how synthesis conditions affect MIT parameters derived from temperature dependence of electrical resistance. Sharp MIT is observed in films sputtered on technologically important Si substrates. The choice of Si (or sapphire) substrates results in the transition temperature above (below) the values obtained for single VO{sub 2} crystals. The MIT becomes narrower and stronger in thinner films. This is consistent with the assumption that the increased width of the MIT in thin films with respect to single crystals is the result of averaging of the transition parameters over a distribution of crystallites in the film. The measurements of MIT in VO{sub 2} patterned into devices do not reveal a noticeable lateral size effect down to 20 {mu}m devices, encouraging use of the phase transition in switching electronic devices. The effect of substrate temperature and ambient during the sputtering on MIT is discussed. While VO{sub 2} films are found to be stable in ambient environment with time, the additional exposure to UV radiation near room temperature is shown to enhance the oxidation kinetics and produce changes in film resistance. Using UV radiation as an additional tool to control the oxidation process during VO{sub 2} synthesis may allow the synthesis temperature to be lowered and an improvement in material quality. We anticipate these results may be of relevance to synthesizing functional oxide films with potential applications in electronics and sensors.

36 MATERIALS SCIENCE↗

Structural-scale levels of development of inelastic martensitic deformation during isothermal loading of submicrocrystalline titanium nickelide in premartensitic condition

The results are presented of an experimental investigation into the regularities and mechanisms of the development of thermoelastic martensitic transformation in submicrocrystalline alloy Ti{sub 49.4}Ni{sub 50.6} with different ways of thermo-power actions using the methods of optical microscopy in situ and X-ray diffraction. The peculiarities of localization of martensite transformation at the meso- and macroscale levels in this alloy with submicrocrystalline structure are considered. Experimental data on the relay mechanism of propagation of the martensitic transformation are presented. The interrelation between the localization of the martensitic transformation on the meso-and macroscale levels and deformation behavior under isothermal loading alloy Ti{sub 49.4}Ni5{sub 0.6} in submicrocrystalline condition are shown and discussed.

36 MATERIALS SCIENCE↗

Zn-doped and undoped SnO{sub 2} nanoparticles: A comparative structural, optical and LPG sensing properties study

Graphical abstract: The X-ray diffraction (XRD) analyses confirm that all the materials prepared are polycrystalline SnO{sub 2} possessing tetragonal rutile structure. On Zn-doping, the crystallite size has been found to decrease from 25 nm (undoped sample) to 13 nm (1 at% Zn-doped sample). Display Omitted Highlights: ► Zn-doped SnO{sub 2} nanoparticles show smaller crystallite size (11–17 nm). ► Optical band gap in SnO{sub 2} nanoparticles increases on Zn-doping. ► 2 at% Zn-doped sample show minimum room temperature resistivity. ► LPG response of the Zn-doped SnO{sub 2} nanoparticles increases considerably. ► 1 at% Zn-doped sample shows maximum response (87%) at 300 °C to 1 vol% concentration. -- Abstract: SnO{sub 2} nanoparticles were prepared by the co-precipitation method with SnCl{sub 4}·5H{sub 2}O as the starting material and Zn(CH{sub 3}COO){sub 2}·2H{sub 2}O as the source of dopant. All the materials prepared have been found to be polycrystalline SnO{sub 2} possessing tetragonal rutile structure with crystallite sizes in the range 11–25 nm. Optical analyses reveal that for the SnO{sub 2} nanoparticles, both undoped and Zn-doped, direct transition occurs with the bandgap energies in the range 3.05–3.41 eV. Variation in the room temperature resistivity of the SnO{sub 2} nanoparticles as a function of dopant concentration has been explained on the basis of two competitive processes: (i) replacement of Sn{sup 4+} ion by an added Zn{sup 2+} ion, and (ii) ionic compensation of Zn{sup 2+} by the formation of oxygen vacancies. Among all the samples examined for LPG sensing, the 1 at% Zn-doped sample exhibits fast and maximum response (∼87%) at 300 °C for 1 vol% concentration of LPG in air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reordering between tetrahedral and octahedral sites in ultrathin magnetite films grown on MgO(001)

Magnetite ultrathin films were grown using different deposition rates and substrate temperatures. The structure of these films was studied using (grazing incidence) x-ray diffraction, while their surface structure was characterized by low energy electron diffraction. In addition to that, we performed x-ray photoelectron spectroscopy and magneto optic Kerr effect measurements to probe the stoichiometry of the films as well as their magnetic properties. The diffraction peaks of the inverse spinel structure, which originate exclusively from Fe ions on tetrahedral sites are strongly affected by the preparation conditions, while the octahedral sites remain almost unchanged. With both decreasing deposition rate as well as decreasing substrate temperature, the integrated intensity of the diffraction peaks originating exclusively from Fe on tetrahedral sites is decreasing. We propose that the ions usually occupying tetrahedral sites in magnetite are relocated to octahedral vacancies. Ferrimagnetic behaviour is only observed for well ordered magnetite films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Application of physical and chemical characterization techniques to metallic powders

Systematic studies have been carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to chemistry, including X-ray diffraction and energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, were also employed. Results of these analyses will be used to shed light on the question: how does virgin powder change after being exposed to and recycled from one or more additive manufacturing build cycles? In addition, these findings can give insight into the actual additive manufacturing process.

36 MATERIALS SCIENCE↗

Three-dimensional profiling using the Fourier transform method with a hexagonal grating projection

We present three-dimensional profilometry based on triangulation in which a hexagonal pattern is projected on the object. To obtain an accurate result with a one-shot photographic image, the Fourier transform method and method of excess fraction are adopted. The three grating components of the hexagonal pattern are used. For compactness a new pattern projection scheme is introduced. The experimental results show that the constructed optical system works well for measuring the profile of a mannequin with a height resolution of {approx} {+-} 1 mm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Corrosion Behavior of Q235 Steel Exposed in Deepwater of South China Sea

For the first time, the corrosion behavior of Q235 steel in 1200, 2000 and 3000 m deepwater of South China Sea for 0.5 year was reported in this study. The corrosion morphology and corrosion products properties were investigated using different techniques, such as 3D optical microscope, scanning electron microscope, x-ray diffraction analyzer and electrochemical impedance spectroscopy. The main environmental factors influencing the corrosion rate of Q235 in deep sea were discussed by applying gray relational analysis. The results indicated that uniform thinning occurred after exposure. A large number of tiny pits were distributed under the corrosion products with a two-layer structure. The corrosion rate and average pitting depth of samples exposed at 2000 m were lower than those exposed at 1200 and 3000 m, and the main environmental factors determining the variation of corrosion rate at different depths were temperature and dissolved oxygen concentration. Hydrostatic pressure had slight effect on the corrosion rate of Q235 steel, but promoted the formation of a more uniform corrosion morphology.

36 MATERIALS SCIENCE↗