Search NASA⌕ Search

SEARCH · Search NASA

Results for “Operational Amplifier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Efficient 30-W, 140-MHz rf amplifier for CW CO2 waveguide laser excitation

Details of a 30-W, 140-MHz rf amplifier for CW CO2 waveguide laser excitation are presented. The amplifier delivers 30 W into a 50-Ohm load while requiring only 40 W of dc power from a 28-V supply and 100 mW of rf drive power for an overall efficiency of 75 percent. A coupling-starting network design theory is given that provides the initiation over voltage for the discharge plasma from an rf power source of limited output voltage capability. The network then matches the drive circuit to the new input impedance of the operating discharge without any adjustments. This design theory applies to the whole class of networks whose losses can be approximated by a loss conductance in parallel with the gas discharge.

Hochuli, U. E.↗

Independent Orbiter Assessment (IOA): Analysis of the DPS subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis/Critical Items List (FMEA/CIL) is presented. The IOA approach features a top-down analysis of the hardware to independently determine failure modes, criticality, and potential critical items. The independent analysis results corresponding to the Orbiter Data Processing System (DPS) hardware are documented. The DPS hardware is required for performing critical functions of data acquisition, data manipulation, data display, and data transfer throughout the Orbiter. Specifically, the DPS hardware consists of the following components: Multiplexer/Demultiplexer (MDM); General Purpose Computer (GPC); Multifunction CRT Display System (MCDS); Data Buses and Data Bus Couplers (DBC); Data Bus Isolation Amplifiers (DBIA); Mass Memory Unit (MMU); and Engine Interface Unit (EIU). The IOA analysis process utilized available DPS hardware drawings and schematics for defining hardware assemblies, components, and hardware items. Each level of hardware was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode. Due to the extensive redundancy built into the DPS the number of critical items are few. Those identified resulted from premature operation and erroneous output of the GPCs.

Lowery, H. J.↗

Ka-Band Waveguide Two-Way Hybrid Combiner for MMIC Amplifiers

The design, simulation, and characterization of a novel Ka-band (32.05 0.25 GHz) rectangular waveguide two-way branch-line hybrid unequal power combiner (with port impedances matched to that of a standard WR-28 waveguide) has been created to combine input signals, which are in phase and with an amplitude ratio of two. The measured return loss and isolation of the branch-line hybrid are better than 22 and 27 dB, respectively. The measured combining efficiency is 92.9 percent at the center frequency of 32.05 GHz. This circuit is efficacious in combining the unequal output power from two Ka-band GaAs pseudomorphic high electron mobility transistor (pHEMT) monolithic microwave integrated circuit (MMIC) power amplifiers (PAs) with high efficiency. The component parts include the branch-line hybrid-based power combiner and the MMIC-based PAs. A two-way branch-line hybrid is a four-port device with all ports matched; power entering port 1 is divided in phase, and into the ratio 2:1 between ports 3 and 4. No power is coupled to port 2. MMICs are a type of integrated circuit fabricated on GaAs that operates at microwave frequencies, and performs the function of signal amplification. The power combiner is designed to operate over the frequency band of 31.8 to 32.3 GHz, which is NASA's deep space frequency band. The power combiner would have an output return loss better than 20 dB. Isolation between the output port and the isolated port is greater than 25 dB. Isolation between the two input ports is greater than 25 dB. The combining efficiency would be greater than 90 percent when the ratio of the two input power levels is two. The power combiner is machined from aluminum with E-plane split-block arrangement, and has excellent reliability. The flexibility of this design allows the combiner to be customized for combining the power from MMIC PAs with an arbitrary power output ratio. In addition, it allows combining a low-power GaAs MMIC with a high-power GaN MMIC. The arbitrary port impedance allows matching the output impedance of the MMIC PA directly to the waveguide impedance without transitioning first into a transmission line with characteristic impedance of 50 ohms. Thus, by eliminating the losses associated with a transition, the overall SSPA efficiency is enhanced. For reducing the cost and weight when required in very large quantities, such as in the beam-forming networks of phased-array antenna systems, the combiner can be manufactured using metal-plated plastic. Two hybrid unequal power combiners can be cascaded to realize a non-binary combiner (for e.g., a three-way) and can be synergistically optimized for low VSWR (voltage standing wave ratio), low insertion loss, high isolation, and wide bandwidth using commercial off-the-shelf electromagnetic software design tools.

Simons, Rainee N.↗

Numerical study of efficiency for a 670 GHz gyrotron

In this paper, the results of the efficiency study of a 670 GHz gyrotron operating at TE{sub 31,8}-mode are presented. Calculations are performed by using the self-consistent nonstationary code MAGY. Three cavity configurations were examined. The effects of ohmic losses and electron velocity spread were included in the simulation. The results show that the output efficiency can reach 35% and the velocity spread in the electron beam does not degrade the operation significantly. Furthermore, we verified that the smoothing of the sharp corners for a small tapering angle would reduce mode conversion; the parasitic excitation of neighboring radial modes is less than 1% of the amplitude of the operating mode and the effect on efficiency is small. Lastly, the simulation results show that the after-cavity interaction causes only slight variations in the efficiency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Three-dimensional particle-in-cell modeling of terahertz gyrotrons with cylindrical and planar configurations of the interaction space

We perform 3D particle-in-cell simulations of terahertz gyrotrons with two different configurations of the interaction space. For a gyrotron with conventional cylindrical configuration of the interaction cavity, we demonstrate reasonable agreement between simulations and experimental results, including output frequency, structure of the higher-order operating mode (TE{sub 17,4}), output power, and ohmic losses. For a novel planar gyrotron scheme with transverse energy extraction, a possibility of further increasing the oversized factor with the single-mode operation regime retained is shown. Frequency detuning by mechanical variation of the gap between waveguide plates is also demonstrated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A broadband gyrotron backward-wave oscillator with tapered interaction structure and magnetic field

The gyro-monotron and gyrotron backward-wave oscillator (gyro-BWO) are the two oscillator versions of gyrotrons. While serving different functions, they are also radically different in the RF field formation mechanisms. The gyro-monotron RF field profile is essentially fixed by the resonant interaction structure, while the gyro-BWO possesses an extra degree of freedom in that the axial RF field profile is self-determined by the beam-wave interaction in a waveguide structure. The present study examines ways to utilize the latter feature for bandwidth broadening with a tapered magnetic field, while also employing a tapered waveguide to enhance the interaction efficiency. We begin with a mode competition analysis, which suggests the theoretical feasibility of broadband frequency tuning in single-mode operation. It is then shown in theory that, by controlling the RF field profile with an up- or down-tapered magnetic field, the gyro-BWO is capable of efficient operation with a much improved tunable bandwidth.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Inferring fusion nuclear burnwidths with low gain photomultiplier impulse response functions

When an inertial confinement fusion implosion is compressed, it maintains thermonuclear density and temperatures for a very short time scale, about 100 ps. The Gamma Reaction History diagnostic measures the time evolution of the fusion burn, but its temporal resolution is limited by the use of a photomultiplier tube (PMT) to amplify the photon signal. Multichannel plate-based PMTs have a fast (~120 ps) full-width at half-max impulse response function (IRF), but the time scale is similar to the incoming physics signal. An analysis routine is used to remove the effect of the PMT IRF and infer the incident fusion burnwidth. With the National Ignition Facility achieving ignition and creating much brighter signals, the PMTs are run at gains three orders of magnitude lower than nominal operation. Calibration at these settings shows the PMT IRFs get ~15% wider. Taking the gain-dependent IRF can affect the inferred nuclear burnwidths by up to ~15%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation of a fine-dispersed liquid-metal target under the action of femto- and picosecond laser pulses for a laser-plasma radiation source in the extreme ultraviolet range

We report the results of studying the dynamics of deformation and fragmentation of liquid-metal droplets under the action of ultrashort laser pulses. The experiments have been performed to optimise the shape of the droplet target used in extreme ultraviolet (EUV) radiation sources based on the laser-produced plasma using the pre-pulse technology. The pre-pulse is generated by a system incorporating a master Ti : sapphire oscillator and a regenerative amplifier, allowing one to vary the pulse duration from 50 fs to 50 ps. The power density of laser radiation at the droplet target, averaged over the pulse duration and spatial coordinates, has reached 3 × 10{sup 15} W cm{sup -2}. The production of liquid-metal droplets has been implemented by means of a droplet generator based on a nozzle with a ring piezoceramic actuator. The droplet material is the eutectic indium – tin alloy. The droplet generator could operate in the droplet and jet regime with a maximal rate of stable operation 5 and 150 kHz, respectively. The spatial stability of droplet position σ = 1% – 2% of its diameter is achieved. The size of the droplets varied within 30 – 70 μm, their velocity was 2 – 8 m s{sup -1} depending on the operation regime. (interaction of laser radiation with matter. laser plasma)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Early Results from NASA’s Laser Communications Relay Demonstration (LCRD) Experiment Program

NASA’s Laser Communications Relay Demonstration (LCRD) mission began its two-year Experiment Program in June of 2022. This experimental phase includes long-term measurement of the effects of the atmosphere (turbulence, weather) on the performance and availability of lasercom. In addition, various future operational scenarios including robotic and exploration missions, and various network service configurations are being emulated. In addition to experiments and demonstrations proposed by the LCRD Investigator Team, NASA enables individuals and groups from government agencies, academia, and industry to propose experiments under the LCRD Guest Experimenters Program. This conference paper provides highlights of the early LCRD experiments and a preview of the remaining experiments, including relaying data to and from the Integrated LCRD Low-Earth Orbit User Modem and Amplifier Terminal (ILLUMA-T) on the International Space Station. The LCRD geosynchronous payload includes two laser communications terminals interconnected via an on-board electronic switch, and can relay information between two optical ground stations located in California and Hawaii. LCRD is a joint project between NASA’s Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory (JPL), and the Massachusetts Institute of Technology Lincoln Laboratory (MIT LL).

lasercom↗

Simons Observatory Microwave SQUID Multiplexing Readout: Cryogenic RF Amplifier and Coaxial Chain Design

The Simons Observatory (SO) is an upcoming polarization-sensitive cosmic microwave background experiment on the Cerro Toco Plateau (Chile) with large overlap with other optical and infrared surveys (e.g., DESI, LSST, HSC). To enable the readout of O(10,000) detectors in each of the four telescopes of SO, we will employ the microwave SQUID multiplexing technology. With a targeted multiplexing factor of O(1000), microwave SQUID multiplexing has never been deployed on the scale needed for SO. Here we present the design of the cryogenic coaxial cable and RF component chain that connects room temperature readout electronics to superconducting resonators that are coupled to transition edge sensor bolometers operating at sub-Kelvin temperatures. We describe design considerations including cryogenic RF component selection, system linearity, noise, and thermal power dissipation.

47 OTHER INSTRUMENTATION↗

Predicted third-order sweet spots for phi-junction Josephson parametric amplifiers

Hybrid superconductor-semiconductor nanowire Josephson junctions exhibit skewed and phi-shifted current phase relations when an in-plane magnetic field is applied along the weak link's spin-orbit effective field direction. These junctions can have an asymmetric Josephson potential with odd-order nonlinearities. A dominant third-order nonlinearity can be achieved by tuning the magnetic field to a sweet spot. Sweet spots persist when higher order Josephson harmonics are included. This makes it possible to have a single Josephson junction dipole element with three-wave mixing capability, which is favorable for pump-efficient amplification. Electrostatic gate tunability of the semiconductor weak link can make it operable within an extended range of working frequencies, and the inclusion of micromagnets can facilitate near-zero magnetic field operation.

Reza, Tasnum [Univ. of Pittsburgh, PA (United Stat↗

A Comprehensive Survey of Readout Strategies for SiPMs Used in Nuclear Imaging Systems

Silicon photomultipliers (SiPMs) offer advantages such as lower relative cost, smaller size, and lower operating voltages compared to photomultiplier tubes. A SiPM’s readout circuit topology can significantly affect the characteristics of an imaging array. In nuclear imaging and detection, energy, timing, and position are the primary characteristics of interest. Nuclear imaging has applications in the medical, astronomy, and high energy physics fields, making SiPMs an active research area. This work is focused on the circuit topologies required for nuclear imaging. We surveyed the readout strategies including the front end preamplification topology choices of transimpedance amplifier, charge amplifier, and voltage amplifier. In addition, a review of circuit topologies suitable for energy, timing, and position information extraction was performed along with a summary of performance limitations and current challenges.

42 ENGINEERING↗

Development of a coded 16-ary CPFSK coherent demodulator

Theory and hardware are described for a proof-of-concept 16-ary continuous phase frequency shift keying (16-CPFSK) digital modem. The 16 frequencies are spaced every 1/16th baud rate for 2 bits/sec/Hz operation. Overall rate 3/4 convolutional coding is incorporated. The demodulator differs significantly from typical quadrature phase detector approaches in that phase is coherently measured by processing the baseband output of a frequency discriminator. Baud rate phase samples from the baseband processor are decoded to yield the original data stream. The method of encoding onto the 16-ary phase nodes, together with convolutional coding gain, results in near quad PSK (QPSK) performance. The modulated signal is of constant envelope; thus the power amplifier can be saturated for peak performance. The spectrum is inherently bandlimited and requires no RF filter.

Clarke, Ken↗

Feedback Processes and Climate Response

The response of the climate system to an external perturbation--e.g., a change in solar irradiance or a change in atmospheric opacity due to an increase in CO2--depends rather strongly on feedback processes in the system, which either amplify or dampen the effects of the initial perturbation. A simple representation of the climate system is used to compare several important feedbacks, based upon general circulation model (GCM) simulations by various investigators. The models are in general agreement with respect to water vapor feedback, but in wide disagreement with respect to cloud feedback. Because of the arguments raised by Lindzen (1990)--that the processes which determine water vapor mixing ratio in the upper atmosphere are quite different from those which operate in the planetary boundary layer, and that upper tropospheric water vapor might actually decrease even when the boundary layer is getting warmer and more moist--researchers undertook a study to determine the sensitivity of climate to changes in water vapor at various levels in the troposphere. The result is that climate is just as sensitive to percentage changes in upper tropospheric water vapor, where the mixing ratio is very small, as it is to percentage changes in the boundary layer, which contains the bulk of total column water vapor.

Arking, Albert↗

Early Results from NASA’s Laser Communications Relay Demonstration (LCRD) Experiment Program

The National Aeronautics and Space Administration’s (NASA) Laser Communications Relay Demonstration (LCRD) mission began its two-year Experiment Program in June 2022. This experimental phase includes long-term measurement of the effects of the atmosphere (turbulence, weather) on the performance and availability of lasercom. Furthermore, various future operational scenarios including robotic and exploration missions and various network service configurations are being emulated. In addition to experiments and demonstrations proposed by the LCRD Investigator Team, NASA enables individuals and groups from government agencies, academia, and industry to propose experiments under the LCRD Guest Experimenters Program. This conference paper provides highlights of the early LCRD experiments and a preview of the future experiments, including relaying data to and from the Integrated LCRD Low-Earth Orbit (LEO) User Modem and Amplifier Terminal (ILLUMA-T) on the International Space Station. The LCRD geosynchronous payload includes two laser communications terminals interconnected via an onboard electronic switch, and can relay information between two optical ground stations located in California and Hawaii. LCRD is a joint project involving NASA Goddard Space Flight Center (GSFC), the NASA Jet Propulsion Laboratory (JPL), and Massachusetts Institute of Technology Lincoln Laboratory (MIT LL).

lasercom↗

Early Results from NASA’s Laser Communications Relay Demonstration (LCRD) Experiment Program

The National Aeronautics and Space Administration’s (NASA) Laser Communications Relay Demonstration (LCRD) mission began its two-year Experiment Program in June 2022. This experimental phase includes long-term measurement of the effects of the atmosphere (turbulence, weather) on the performance and availability of lasercom. Furthermore, various future operational scenarios including robotic and exploration missions and various network service configurations are being emulated. In addition to experiments and demonstrations proposed by the LCRD Investigator Team, NASA enables individuals and groups from government agencies, academia, and industry to propose experiments under the LCRD Guest Experimenters Program. This conference paper provides highlights of the early LCRD experiments and a preview of the future experiments, including relaying data to and from the Integrated LCRD Low-Earth Orbit (LEO) User Modem and Amplifier Terminal (ILLUMA-T) on the International Space Station. The LCRD geosynchronous payload includes two laser communications terminals interconnected via an onboard electronic switch, and can relay information between two optical ground stations located in California and Hawaii. LCRD is a joint project involving NASA Goddard Space Flight Center (GSFC), the NASA Jet Propulsion Laboratory (JPL), and Massachusetts Institute of Technology Lincoln Laboratory (MIT LL).

lasercom↗

Theoretical and experimental analysis of bidirectionally pumped 1.3 μm Pr{sup 3+}-doped ASE source

We have analyzed the characteristics of 1.3 μm praseodymium (Pr{sup 3+}) doped bidirectionally pumped double pass (BIP-DP) configuration amplified spontaneous emission (ASE) source theoretically and experimentally. The source’s simulation model was established and corresponding simulated results were given. The effects of pump ratio, Pr{sup 3+}-doped fiber (PDF) length, total pump power and source’s optical losses were researched. The output power of BIP-DP ASE source is mainly affected by the total pump power, PDF length and source’s optical losses, while it has little relationship with the pump ratio. The BIP-DP ASE source operating at the symmetric bi-directional pump condition was constructed experimentally. The acquired output power of more than 5 mW has been obtained experimentally, which was with the quasi-gaussian output spectrum, and its 3 dB bandwidth is ~ 20 nm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Cracking in polymer substrates for flexible electronic devices and its mitigation

Mechanical reliability plays a critical role in determining the durability of flexible electronic devices because of the significant mechanical stresses they experience during manufacturing and operation. Many such devices are built on sheets comprising stiff transparent-conducting oxide (TCO) electrode films on compliant polymer substrates, and it is generally assumed that the high-toughness polymer substrates do not crack. Contrary to this assumption, here we show extensive cracking in the polymer substrates during bending of a variety of TCO/polymer sheets, and a device example — flexible perovskite solar cells. Such substrate cracking, which compromises the overall mechanical integrity of the entire device, is driven by the amplified stress-intensity factor caused by the elastic mismatch at the film/substrate interface. To mitigate this substrate cracking, an interlayer-engineering approach is designed and experimentally demonstrated. This approach is potentially applicable to myriad flexible electronic devices, with stiff films on compliant substrates, for improving their durability and reliability.

42 ENGINEERING↗