Search NASA⌕ Search

SEARCH · Search NASA

Results for “PIPES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Sensor Reduction for Diversion Detection in a Realistic Heat Pipe Microreactor Using Supervised Machine Learning

Microreactors are designed as a smaller, cheaper, and safer alternative to traditional nuclear power plants. Their non-traditional characteristics and prospect of mass production and deployment will likely require new approaches to nuclear safeguards. The primary proliferation concern with microreactors is the diversion of fuel material. Such diversion may produce measurable defects in key physical attributes like neutron flux, which may in turn be detectable using machine learning models. Preliminary work has demonstrated this ability for modeled nominal and diversion scenarios using large quantities of energy integrated neutron flux data. In practice, the number of available sensors for such measurements will be limited and energy integrated flux information will not be available. This work explores the ability of tree-based gradient boosted ensemble models to classify a given microreactor core is nominal or diversion, and determine the number of fuel pins diverted in the case of diversion with reduced numbers of sensors and more realistic detector responses. Classification accuracy of greater than 98% and regression errors as low as 5% of the total number of fuel pins were achieved with as few as 15 sensors, compared to 99% and 4.1% with a maximum of 240 sensors.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Prediction of residual stresses in a multipass pipe weld by a novel 3D finite element approach

Due to enormous computation cost, current residual stress simulation of multipass girth welds are mostly performed using two-dimensional (2D) axisymmetric models. The 2D model can only provide limited estimation on the residual stresses by assuming its axisymmetric distribution. In this study, a highly efficient thermal-mechanical finite element code for three-dimensional (3D) model has been developed based on high performance Graphics Processing Unit (GPU) computers. Our code is further accelerated by considering the unique physics associated with welding processes that are characterized by steep temperature gradient and a moving arc heat source. It is capable of modeling large-scale welding problems that cannot be easily handled by the existing commercial simulation tools. To demonstrate the accuracy and efficiency, our code was compared with a commercial software by simulating a 3D multi-pass girth weld model with over 1 million elements. Our code achieved comparable solution accuracy with respect to the commercial one but with over 100 times saving on computational cost. Moreover, the three-dimensional analysis demonstrated more realistic stress distribution that is not axisymmetric in hoop direction.

Huang, Hui↗

Research and Development Roadmaps for Nondestructive Evaluation of Cables, Concrete, Reactor Pressure Vessels, and Piping Fatigue

The purpose of the Materials Aging and Degradation Pathway is to develop the scientific basis for understanding and predicting long-term environmental degradation behavior of materials in nuclear power plants and to provide data and methods to assess the performance of systems, structures, and components essential to safe and sustained nuclear power plant operations. The understanding of aging-related phenomena and their impacts on systems, structures, and components is expected to be a significant issue for any nuclear power plant planning for long-term operations (i.e., service beyond the initial license renewal period). Management of those phenomena and their impacts during long-term operations can be better enabled by improved methods and techniques for detection, monitoring, and prediction of systems, structures, and components degradation.

Materials Aging↗

Corrugated Metal Pipes Category of Transuranic Waste Stored Below Ground within Area G

The primary regulatory driver for environmental cleanup at the Los Alamos National Laboratory (LANL) is the March 2005 Compliance Order on Consent (Consent Order), an agreement between LANL and the New Mexico Environment Department (NMED) that contains specific requirements and schedules for cleaning up historical contamination at the LANL site. The Consent Order has a final deliverable date of December 2015 (Reference 1). The Consent Order does not address requirements for removing transuranic (TRU) waste from the LANL site; therefore TRU waste removal was typically placed at lower priority in budget decisions. Removal of TRU waste stored both above ground and below ground at Technical Area 54 (TA-54) Area G is required before a remedy is implemented under the Consent Order for Material Disposal Area G (MDA G, which is the below-ground portion of Area G). After the Las Conchas Fire burned large areas near Los Alamos in 2011, New Mexico Governor Susana Martinez asked the U.S. Department of Energy (DOE) to provide sufficient funding for cleanup of defense legacy wastes from LANL and for TRU waste disposal at the Waste Isolation Pilot Plant (WIPP). Discussions were held with the NMED on accelerating TRU waste removal from LANL.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Roughness Tolerance Studies for the Undulator Beam Pipe Chamber of LCLS-II

When a bunch passes through the undulator of LCLS-II, the wakefields of the vacuum chamber will result in an added energy variation along the bunch, one that can negatively impact the FEL performance. The wakefield of the vacuum chamber is primarily due to the resistance of the walls and the roughness of the surface. To minimize the impact of the wakes, one would like a wall surface smooth enough so that the roughness component of the wake is a small fraction of the total wake. In LCLS-I, with an undulator vacuum chamber of the same material (aluminum) and roughly the same aperture as proposed for LCLS-II, the wall roughness tolerance specified as an rms slope of the surface of (y') rms = 10–15 mr was difficult to achieve. The goal of this study is to understand the consequences to LCLS-II of loosening the roughness specification, say by a factor of 2 to 30 mr.

ACCPHY↗

Techniques for energetic ion assisted in-situ coating of long, small diameter, beam pipes with compacted thick crystalline copper film

High wall resistivity can cause heating and instabilities in accelerators. Electron clouds in accelerators limit machine performance through associated dynamical instabilities and/or vacuum pressure increases. Coating accelerator vacuum tubes with compacted thick crystalline copper will mitigate those problems and can enhance luminosity. Develop compact ion assisted deposition (IAD) devices by incorporating ion bombardment in a robotic cylindrical magnetron sputtering device configured for small radial dimension tubes for in-situ coating of long, small diameter tubes with defect free thick films copper. Selected an ion assisted plasma deposition technique for in-situ coating of long, small diameter tubes. Set up a cryogenic resonator for measuring conductivity of deposited copper at cryogenic temperature to optimize the deposition technique; preliminary design of phase II full-scale device. Coating of existing accelerator vacuum tubes with compacted thick crystalline copper is a very cost effective way to mitigate significant problems in accelerators trying to increase luminosity. IAD results in superior quality film deposition, which due to inefficiencies, is presently restricted to high value items. Advancing to industry forefront more cost effective IAD, will improve tools, ball bearings & other lower value industrial products, thus reducing waste as well as improving industrial accelerators and electron guns, impacting companies who utilize accelerators. Develop improved inexpensive plasma deposition for copper coating accelerator tubes with compacted thick crystalline copper. Although there are commercial applications, initial project focus is to facilitate cost-effective luminosity increase in RHIC at BNL as well as other machines.

43 PARTICLE ACCELERATORS↗