Search NASA⌕ Search

SEARCH · Search NASA

Results for “Value Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Self-calibrating solar position sensor

A sun positioning sensor and method of accurately tracking the sun are disclosed. The sensor includes a position sensing diode and a disk having a body defining an aperture for accepting solar light. An extension tube having a body that defines a duct spaces the position sensing diode from the disk such that the solar light enters the aperture in the disk, travels through the duct in the extension tube and strikes the position sensing diode. The extension tube has a known length that is fixed. Voltage signals indicative of the location and intensity of the sun are generated by the position sensing diode. If it is determined that the intensity values are unreliable, then historical position values are used from a table. If the intensity values are deemed reliable, then actual position values are used from the position sensing diode.

14 SOLAR ENERGY↗

Determination of water equivalent content in fuel rods

In water-cooled reactors, hydriding failure of zircaloy cladding tubes can be easily caused by high content of total water in fuel rods. WEC, which is the water equivalent content within the cold space of a fuel rod, directly reflects the total water content of the fuel rod. A device measuring WEC has been designed, manufactured and tested. This extraction device is a hermetically sealed system consisting of six parts: the break-off part, the heating unit, the reduction unit, the sample storage part, the collecting unit and the gas flow system. Each part is connected to another one using a special connection, and the device's end part is connected to a gas chromatograph. The determination procedure can be briefly summarized as follows: first, a test fuel rod should be put into the sealed device after lathing two circular grooves on both ends, so that it can be easily broken at these points in the break-off part. Driven by carrier gas, water and hydrogen both contained in helium gas and absorbed on the rod in-wall pass over the hot uranium filament where water is converted into hydrogen. After being concentrated by the collecting unit, hydrogen flows into the gas chromatograph for measurement and data are calculated as total water content A. UO{sub 2} pellets in the test rod should be taken out from the sample storage part and the total hydrogen content of these pellets is determined according to ASTM C1457 standard, followed by its conversion into total water content B. Finally, the sum of A and B being divided by the free volume of the cold space within the test rod, gives the value of WEC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nuclear-Rocket Propulsion

The three basic types of nuclear power-plants (solid, liquid, and gas core) are compared on the bases of performance potential and the status of current technology. The solid-core systems are expected to have impulses in the range of 850 seconds, any thrust level (as long as it is greater than 10,000 pounds (44,480 newtons)), and thrust-to-engine-weight ratios of 2 to 20 pounds per pound (19.7 to 197 newtons per kilogram). There is negligible or no fuel loss from the solid-core system. The solid-core system, of course, has had the most work done on it. Large-scale tests have been performed on a breadboard engine that has produced specific impulses greater than 700 seconds at thrust levels of about 50,000 pounds (222,000 newtons). The liquid-core reactor would be interesting in the specific impulse range of 1200 to 1500 seconds. Again, any thrust level can be obtained depending on how big or small the reactor is made. The thrust-to-engine weight ratio for these systems would be in the range of 1 to 10. The discouraging feature of the liquid-core system is the high fuel-loss ratio anticipated. Values of 0.01 to 0.1 pound (0.00454 to 0.0454 kilograms) or uranium loss per pound (0.454 kilograms) of hydrogen are expected, if impulses in the range of 1200 to 1500 seconds are desired. The gas-core reactor shows specific impulses in the range of 1500 to 2500 seconds. The thrust levels should be at least as high as the weight so that the thrust-to-weight ratio does not go below 1. Because the engine weight is not expected to be under 100,000 pounds (444,800 newtons), thrust levels higher than 100,000 pounds (448,000 newtons) are of interest. The thrust-to-engine weights, in that case, would run from 1 to 20 pounds per pound (9.8 to 19.7 kilograms). Gas-core reactors tend to be very large, and can have high thrust-to-weight ratios. As in the case of the liquid-core system, the fuel loss that will be attendant with gas cores as envisioned today will be rather high. The loss rates will be 0.01 to 0.1 pound of uranium (0.00454 to 0.0454 kilograms) for each pound (0.454 kilograms) of hydrogen.

Rom, Frank E.↗

A Combined Water and CO 2 Direct Air Capture System (Final Technical Report)

The primary objective of the project was to demonstrate the technical and economic performance of a technology that simultaneously captures CO 2 and water from the air – a Hybrid Direct Air Capture system (HDAC). In HDAC, air is passed over water capture section as well as a CO 2 selective sorbent to remove CO 2 from the air stream. Combining potable water generation and CO 2 capture in a single device with the unique energy conserving features of the proposed design enables long-term projected CAPEX under $\$$750/t-CO 2 and levelized cost of capture (LCOC) of $\$$140/t-CO 2 . Project DE-FE-0031970 "A Combined Water and CO 2 Direct Air Capture System" ran for four years and three months from 10/01/2020 to 12/31/2024 for three budget periods and an extension period. The total project budget at completion was $\$$3,534,408 consisting of a $\$$2,680,064 federal share and $\$$854,344 cost share. The pilot plant was successfully designed, engineered, built and commissioned during the initial three budget periods. The plant demonstrated successful water capture during this period, whereas initial CO 2 capture was well below target values. The project team requested an extension period during which alternate materials and beds were evaluated. By the end of the project, both moisture swing adsorption of CO 2 and water capture had successfully been demonstrated at target capture rates making further scale-up of the technology viable.

42 ENGINEERING↗

Evaluating the limitations of Bayesian metabolic control analysis

AbstractBayesian Metabolic Control Analysis (BMCA) has emerged as a promising framework for inferring metabolic control coefficients in data-limited scenarios by integrating Bayesian inference with linlog rate laws. However, its predictive accuracy and limitations remain underexplored. This study systematically evaluates BMCA’s ability to infer elasticity values, flux control coefficients (FCCs), and concentration control coefficients (CCCs) under varying data availability conditions using three synthetic metabolic network models. Our findings highlight the strengths and weaknesses of BMCA, guiding its application in metabolic engineering and emphasizing the need for methodological refinements.Author summaryUnderstanding how enzymes control metabolic pathways is crucial for optimizing biomanufacturing and synthetic biology applications. Bayesian Metabolic Control Analysis (BMCA) is a promising computational method that integrates Bayesian inference with metabolic control analysis to estimate key control parameters, even in cases with limited experimental data. However, the accuracy and limitations of BMCA remain unclear. In this study, we systematically evaluate BMCA using three synthetic metabolic networks to determine how different types of physiological data impact its predictive performance. We find that BMCA requires flux and enzyme concentration data for accurate predictions, while external metabolite concentrations contribute little. Additionally, BMCA fails to predict elasticity values beyond a magnitude of 1.5 and reliably infer allosteric regulation, even when strong regulatory interactions exist. In addition, BMCA does not accurately rank metabolic control points, which may limit its utility in identifying key enzymes in engineered pathways. Our work provides practical insights into when and how BMCA can be applied, guiding future research in metabolic modeling and control analysis.

Shin, Janis (ORCID:0000000216572455)↗

Sensor failure detection and recovery by neural networks

A new method of sensor failure detection, isolation, and accommodation is described using a neural network approach. In a propulsion system such as the Space Shuttle Main Engine, the dynamics are usually much higher than the order of the system. This built-in redundancy of the sensors can be utilized to detect and correct sensor failure problems. The goal of the proposed scheme is to train a neural network to identify the sensor whose measurement is not consistent with other sensor outputs. Another neural network is trained to recover the value of critical variables when their measurements fail. Techniques for training the network with a limited amount of data are developed. The proposed scheme is tested using the simulated data of the Space Shuttle Main Engine (SSME) inflight sensor group.

Guo, Ten-Huei↗

Fuel Spray and Flame Formation in a Compression-Ignition Engine Employing Air Flow

The effects of air flow on fuel spray and flame formation in a high-speed compression-ignition engine have been investigated by means of the NACA combustion apparatus. The process was studied by examining high-speed motion pictures taken at the rate of 2,200 frames a second. The combustion chamber was of the flat-disk type used in previous experiments with this apparatus. The air flow was produced by a rectangular displacer mounted on top of the engine piston. Three fuel-injection nozzles were tested: a 0.020-inch single-orifice nozzle, a 6-orifice nozzle, and a slit nozzle. The air velocity within the combustion chamber was estimated to reach a value of 425 feet a second. The results show that in no case was the form of the fuel spray completely destroyed by the air jet although in some cases the direction of the spray was changed and the spray envelope was carried away by the moving air. The distribution of the fuel in the combustion chamber of a compression-ignition engine can be regulated to some extent by the design of the combustion chamber, by the design of the fuel-injection nozzle, and by the use of air flow.

Rothrock, A M↗

Nanostructured Lanthanum Halides and CeBr3 for Nuclear Radiation and Detection

Scintillator materials are used to detect, and in some cases identify, gamma rays. Higher performance scintillators are expensive, hard to manufacture, fragile, and sometimes require liquid nitrogen or cooling engines. But whereas lower-quality scintillators are cheap, easy to manufacture, and more rugged, their performance is lower. At issue: can the desirable qualities of high-and low-performance scintillators be combined to achieve better performance at lower cost? Preliminary experiments show that a LaF{sub 3}:Ce oleic acid-based nanocomposite exhibits a photopeak when exposed to {sup 137}Cs source gamma-radiation. The chemical synthesis of the cerium-doped lanthanum halide nanoparticles are scalable and large quantities of material can be produced at a time, unlike typical crystal growth processes such as the Bridgeman process. Using a polymer composite (Figure 1), produced by LANL, initial measurements of the unloaded and 8% LaF{sub 3}:Ce-loaded sample have been made using {sup 137}Cs sources. Figure 2 shows an energy spectrum acquired for CeF{sub 3}. The lighter plot is the measured polymer-only spectrum and the black plot is the spectrum from the nanocomposite scintillator. As the development of this material continues, the energy resolution is expected to improve and the photopeak-to-Compton ratio will become greater at higher loadings. These measurements show the expected Compton edge in the polymer-only sample, and the Compton edge and photo-peak expected in the nanophosphor composites that LANL has produced. Using a porous VYCORR with CdSe/ZnS core shell quantum dots, Letant has demonstrated that he has obtained signatures of the 241Am photopeak with energy resolution as good at NaI (Figure 3). We begin with the fact that CeBr{sub 3} crystals do not have a self-activity component as strong as the lanthanum halides. The radioactive 0.090% {sup 138}La component of lanthanum leads to significant self-activity, which will be a problem for very large detector volumes. Yet a significant strength of the nanostructure detector concept is the ability to create extremely large detector volumes by mixing nanoparticles into a transparent matrix. This would argue for use of nanoparticles other than lanthanum halides. Nanocomposites are easy to prepare; it is much less costly to use nanocomposites than to grow large whole crystals of these materials. The material can be fabricated at an industrial scale, further reducing cost. This material potentially offers the performance of $300/cc material (e.g., lanthanum bromide) at a cost of $1/cc. Because the material acts as a plastic, it is rugged and flexible, and can be made in large sheets, increasing the sensitivity of a detector using it. It would operate at ambient temperatures. Very large volumes of detector may be produced at greatly reduced cost, enhancing the non-proliferation posture of the nation for the same dollar value.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Low NOx heavy fuel combustor concept program addendum: Low/mid heating value gaseous fuel evaluation

The combustion performance of a rich/quench/lean (RQL) combustor was evaluated when operated on low and mid heating value gaseous fuels. Two synthesized fuels were prepared having lower heating values of 10.2 MJ/cu m. (274 Btu/scf) and 6.6 MJ/cu m (176 Btu/scf). These fuels were configured to be representative of actual fuels, being composed primarily of nitrogen, hydrogen, carbon monoxide, and carbon dioxide. A liquid fuel air assist fuel nozzle was modified to inject both of the gaseous fuels. The RQL combustor liner was not changed from the configuration used when the liquid fuels were tested. Both gaseous fuels were tested over a range of power levels from 50 percent load to maximum rated power of the DDN Model 570-K industrial gas turbine engine. Exhaust emissions were recorded for four power level at several rich zone equivalence ratios to determine NOx sensitivity to the rich zone operating point. For the mid Btu heating value gas, ammonia was added to the fuel to simulate a fuel bound nitrogen type gaseous fuel. Results at the testing showed that for the low heating value fuel NOx emissions were all below 20 ppmc and smoke was below a 10 smoke number. For the mid heating value fuel, NOx emissions were in the 50 to 70 ppmc range with the smoke below a 10 smoke number.

Novick, A. S.↗

Simulations of space charge in the Fermilab Main Injector

The Fermilab Project X plan for future high intensity operation relies on the Main Injector as the engine for delivering protons in the 60-120 GeV energy range. Project X plans call for increasing the number of protons per Main Injector bunch from the current value of 1.0 x 10{sup 11} to 3.0 x 10{sup 11}. Space charge effects at the injection energy of 8 GeV have the potential to seriously disrupt operations. We report on ongoing simulation efforts with Synergia, MARYLIE/Impact, and IMPACT, which provide comprehensive capabilities for parallel, multi-physics modeling of beam dynamics in the Main Injector including 3D space-charge effects.

43 PARTICLE ACCELERATORS↗

Multidimensional Numerical Simulations of Knocking Combustion in a Cooperative Fuel Research Engine

A numerical approach was developed based on multidimensional computational fluid dynamics (CFD) to predict knocking combustion in a cooperative fuel research (CFR) engine. G-equation model was employed to track the turbulent flame front and a multizone model was used to capture auto-ignition in the end-gas. Furthermore, a novel methodology was developed wherein a lookup table generated from a chemical kinetic mechanism could be employed to provide laminar flame speed as an input to the Gequation model, instead of using empirical correlations. To account for fuel chemistry effects accurately and lower the computational cost, a compact 121-species primary reference fuel (PRF) skeletal mechanism was developed from a detailed gasoline surrogate mechanism using the directed relation graph (DRG) assisted sensitivity analysis (DRGASA) reduction technique. Extensive validation of the skeletal mechanism was performed against experimental data available from the literature on both homogeneous ignition delay and laminar flame speed. The skeletal mechanism was used to generate lookup tables for laminar flame speed as a function of pressure, temperature, and equivalence ratio. The numerical model incorporating the skeletal mechanism was employed to perform simulations under research octane number (RON) and motor octane number (MON) conditions for two different PRFs. Parametric tests were conducted at different compression ratios (CR) and the predicted values of critical CR, delineating the boundary between “no knock” and “knock,” were found to be in good agreement with available experimental data. The virtual CFR engine model was, therefore, demonstrated to be capable of adequately capturing the sensitivity of knock propensity to fuel chemistry.

CFD↗

RB-TnSeq elucidates dicarboxylic-acid-specific catabolism in β-proteobacteria for improved plastic monomer upcycling

Dicarboxylic acids are key components of many polymers and plastics, making them a target for both engineered microbial degradation and sustainable bioproduction. In this study, we generated a comprehensive data set of functional evidence for the genetic basis of dicarboxylic and fatty acid metabolism using randomly barcoded transposon sequencing (RB-TnSeq). We identified four β-proteobacteria that displayed robust growth with dicarboxylic acid sole carbon source and cultured their mutant libraries with dicarboxylic and fatty acids with carbon chain lengths from C3 to C12. The resulting fitness data suggested that dicarboxylic and fatty acid metabolisms are largely distinct, and different sets of β-oxidation genes are required for catabolizing dicarboxylic versus fatty acids of the same carbon chain lengths. In addition, we identified transcriptional regulators and transporters with strong fitness phenotypes related to dicarboxylic acid utilization. In Ralstonia sp. UNC404CL21Col (R. CL21), we deleted two transcriptional repressors to improve its utilization of short-chain dicarboxylic acids. We exploited the diacid-utilizing catabolism of R. CL21 to upcycle a mock mixture of the dicarboxylic acids produced when polyethylene is oxidized. After introducing a heterologous indigoidine production pathway, this engineered Ralstonia produced 0.56 ± 0.02 g/L indigoidine from a mixture of dicarboxylic acids as a carbon source, demonstrating the potential of R. CL21 to upcycle plastic wastes to products derived from tricarboxylic acid (TCA) cycle intermediates. IMPORTANCE: Upcycling the carbon in plastic wastes to value-added products is a promising approach to address the plastic waste and climate crises, and dicarboxylic acid metabolism is an important facet of several approaches. Improving our understanding of the genetic basis of this metabolism has the potential to uncover new enzymes and genetic parts for engineered pathways involving dicarboxylic acids. Our data set is the most comprehensive interrogation of dicarboxylic acid catabolism to date, and this work will be of utility to researchers interested in both plastics bioproduction and upcycling applications.

Pearson, Allison N↗

SU-F-R-12: Prediction of TrueBeam Hardware Issues Using Trajectory Log Analysis

Purpose: To predict potential failures of hardware within the Varian TrueBeam linear accelerator in order to proactively replace parts and decrease machine downtime. Methods: Machine downtime is a problem for all radiation oncology departments and vendors. Most often it is the result of unexpected equipment failure, and increased due to lack of in-house clinical engineering support. Preventative maintenance attempts to assuage downtime, but often is ineffective at preemptively preventing many failure modes such as MLC motor failures, the need to tighten a gantry chain, or the replacement of a jaw motor, among other things. To attempt to alleviate downtime, software was developed in house that determines the maximum value of each axis enumerated in the Truebeam trajectory log files. After patient treatments, this data is stored in a SQL database. Microsoft Power BI is used to plot the average maximum error of each day of each machine as a function of time. The results are then correlated with actual faults that occurred at the machine with the help of Varian service engineers. Results: Over the course of six months, 76,312 trajectory logs have been written into the database and plotted in Power BI. Throughout the course of analysis MLC motors have been replaced on three machines due to the early warning of the trajectory log analysis. The service engineers have also been alerted to possible gantry issues on one occasion due to the aforementioned analysis. Conclusion: Analyzing the trajectory log data is a viable and effective early warning system for potential failures of the TrueBeam linear accelerator. With further analysis and tightening of the tolerance values used to determine a possible imminent failure, it should be possible to pinpoint future issues more thoroughly and for more axes of motion.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Reducing GHG emissions in the United States' transportation sector

Reducing GHG emissions in the U.S. transportation sector requires both the use of highly efficient propulsion systems and low carbon fuels. This study compares reduction potentials that might be achieved in 2060 for several advanced options including biofuels, hybrid electric vehicles (HEV), plug-in hybrid electric vehicles (PHEV), and fuel cell electric vehicles (FCEV), assuming that technical and cost reduction targets are met and necessary fueling infrastructures are built. The study quantifies the extent of the reductions that can be achieved through increasing engine efficiency and transitioning to low-carbon fuels separately. Decarbonizing the fuels is essential for achieving large reductions in GHG emissions, and the study quantifies the reductions that can be achieved over a range of fuel carbon intensities. Although renewables will play a vital role, some combination of coal gasification with carbon capture and sequestration, and/or nuclear energy will likely be needed to enable very large reductions in carbon intensities for hydrogen and electricity. Biomass supply constraints do not allow major carbon emission reductions from biofuels alone; the value of biomass is that it can be combined with other solutions to help achieve significant results. Compared with gasoline, natural gas provides 20% reduction in GHG emissions in internal combustion engines and up to 50% reduction when used as a feedstock for producing hydrogen or electricity, making it a good transition fuel for electric propulsion drive trains. The material in this paper can be useful information to many other countries, including developing countries because of a common factor: the difficulty of finding sustainable, low-carbon, cost-competitive substitutes for petroleum fuels.

01 COAL, LIGNITE, AND PEAT↗

Analysis of pumped thermal energy storage using particle media integrated with concentrating solar power

Pumped Thermal Energy Storage (PTES) is an electricity storage system that converts electricity into thermal energy which is stored and later transformed back into electricity. Previous work has illustrated that particles have low capital costs and can be operated over a wide range of temperatures. PTES with particle storage achieves higher round-trip efficiency and specific power output than when molten salt thermal energy storage is used. This article explores hybrid systems that combine PTES with Concentrating Solar Power (CSP). Hybrid systems share the majority of components thereby reducing costs compared to two stand-alone devices. In addition, hybrid systems can provide multiple services (such as renewable power generation and electricity storage services). Using particle thermal storage in these hybrid concepts provides freedom in choosing the design conditions, since a wide range of operating temperatures is allowable, therefore making it possible to identify hybrid system designs that have good performance. In this article, two concepts for hybrid PTES-CSP are introduced. Thermodynamic models are developed and these are used to evaluate the performance of two hybrid systems. These models account for turbomachinery efficiency, and approach temperature and pressure loss in heat exchangers, as well as other sources of inefficiency, such as motor-generator losses, and air fan power. The “Solar Top-Up” Concept uses CSP to increase the temperature delivered by the charging heat pump. The discharging system uses a topping gas cycle and a bottoming steam cycle to fully exploit the available energy. Using solar heat to increase the maximum temperature from 750 K to 1100 K increases the round-trip efficiency from 41 % to 62 % and the specific work output from 88 kJ/kg to 301 kJ/kg. The second concept is a “Dual-Mode” device which provides both electricity storage and solar electricity generation with the same set of components. The PTES-mode and CSP-mode performance are optimized at different design values but careful parameter selection leads to good performance of both modes: one design produces PTES round-trip efficiency > 60 %, CSP heat engine efficiency > 40 %, and specific work outputs > 150 kJ/kg (for both cycles), when the particle receiver temperature is > 1200 K and maximum heat pump temperature is 1100 K.

14 SOLAR ENERGY↗

Band alignment and electrical properties of Al{sub 2}O{sub 3}/β-Ga{sub 2}O{sub 3} heterojunctions

The band alignment of Al{sub 2}O{sub 3}/n-Ga{sub 2}O{sub 3} was investigated by x-ray photoelectron spectroscopy (XPS). With a band gap of 6.8 ± 0.2 eV measured for Al{sub 2}O{sub 3}, the conduction and valence band offsets at the interface were estimated to be 1.5 ± 0.2 eV and 0.7 ± 0.2 eV, respectively. The conduction band offset was also obtained from tunneling current in Al{sub 2}O{sub 3}/n-Ga{sub 2}O{sub 3} (2{sup ¯}01) metal-oxide-semiconductor (MOS) diodes using the Fowler-Nordheim model. The electrically extracted value was in good agreement with the XPS data. Furthermore, the MOS diodes exhibited small capacitance-voltage hysteresis loops, indicating the successful engineering of a high-quality Al{sub 2}O{sub 3}/Ga{sub 2}O{sub 3} interface.

36 MATERIALS SCIENCE↗

A Multi-Objective Bayesian Optimization Approach Using the Weighted Tchebycheff Method

Abstract Bayesian optimization (BO) is a low-cost global optimization tool for expensive black-box objective functions, where we learn from prior evaluated designs, update a posterior surrogate Gaussian process model, and select new designs for future evaluation using an acquisition function. This research focuses upon developing a BO model with multiple black-box objective functions. In the standard multi-objective (MO) optimization problem, the weighted Tchebycheff method is efficiently used to find both convex and non-convex Pareto frontiers. This approach requires knowledge of utopia values before we start optimization. However, in the BO framework, since the functions are expensive to evaluate, it is very expensive to obtain the utopia values as a prior knowledge. Therefore, in this paper, we develop a MO-BO framework where we calibrate with multiple linear regression (MLR) models to estimate the utopia value for each objective as a function of design input variables; the models are updated iteratively with sampled training data from the proposed MO-BO. These iteratively estimated mean utopia values are used to formulate the weighted Tchebycheff MO acquisition function. The proposed approach is implemented in two numerical test examples and one engineering design problem of optimizing thin tube geometries under constant loading of temperature and pressure, with minimizing the risk of creep-fatigue failure and design cost, along with risk-based and manufacturing constraints. Finally, the model accuracy with frequentist, Bayesian and without MLR-based calibration are compared to true Pareto solutions.

Engineering↗