Search NASA⌕ Search

SEARCH · Search NASA

Results for “Waste Form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

MELT RATE ENHANCEMENT FOR HIGH ALUMINUM HLW (HIGH LEVEL WASTE) GLASS FORMULATION FINAL REPORT 08R1360-1

This report describes the development and testing of new glass formulations for high aluminum waste streams that achieve high waste loadings while maintaining high processing rates. The testing was based on the compositions of Hanford High Level Waste (HLW) with limiting concentrations of aluminum specified by the Office of River Protection (ORP). The testing identified glass formulations that optimize waste loading and waste processing rate while meeting all processing and product quality requirements. The work included preparation and characterization of crucible melts and small scale melt rate screening tests. The results were used to select compositions for subsequent testing in a DuraMelter 100 (DM100) system. These tests were used to determine processing rates for the selected formulations as well as to examine the effects of increased glass processing temperature, and the form of aluminum in the waste simulant. Finally, one of the formulations was selected for large-scale confirmatory testing on the HLW Pilot Melter (DM1200), which is a one third scale prototype of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) HLW melter and off-gas treatment system. This work builds on previous work performed at the Vitreous State Laboratory (VSL) for Department of Energy (DOE) to increase waste loading and processing rates for high-iron HLW waste streams as well as previous tests conducted for ORP on the same high-aluminum waste composition used in the present work and other Hanford HLW compositions. The scope of this study was outlined in a Test Plan that was prepared in response to an ORP-supplied statement of work. It is currently estimated that the number of HLW canisters to be produced in the WTP is about 13,500 (equivalent to 40,500 MT glass). This estimate is based upon the inventory of the tank wastes, the anticipated performance of the sludge treatment processes, and current understanding of the capability of the borosilicate glass waste form. The WTP HLW melter design, unlike earlier DOE melter designs, incorporates an active glass bubbler system. The bubblers create active glass pool convection and thereby improve heat transfer and glass melting rate. The WTP HLW melter has a glass surface area of 3.75 m{sup 2} and depth of {approx}1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HLW waste processing rates can potentially be achieved by increasing the melter operating temperature above 1150 C and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage. The current estimates and glass formulation efforts have been conservative in terms of achievable waste loadings. These formulations have been specified to ensure that the glasses are homogenous, contain essentially no crystalline phases, are processable in joule-heated, ceramic-lined melters and meet WTP Contract terms. The WTP's overall mission will require the immobilization of tank waste compositions that are dominated by mixtures of aluminum (Al), chromium (Cr), bismuth (Bi), iron (Fe), phosphorous (P), zirconium (Zr), and sulfur (S) compounds as waste-limiting components. Glass compositions for these waste mixtures have been developed based upon previous experience and current glass property models. Recently, DOE has initiated a testing program to develop and characterize HLW glasses with higher waste loadings. Results of this work have demonstrated the feasibility of increases in wasteloading from about 25 wt% to 33-50 wt% (based on oxide loading) in the glass depending on the waste stream. It is expected that these higher waste loading glasses will reduce the HLW canister production requirement by about 25% or more.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis and Characterization of 5- and 6- Coordinated Alkali Pertechnetates

The local chemistry of technetium-99 ( 99 Tc) in oxide glasses is important for understanding the incorporation and long-term release of Tc from nuclear waste glasses, both those for legacy defense wastes and fuel reprocessing wastes. Tc preferably forms Tc(VII), Tc(IV), or Tc(0) in glass, depending on the level of reduction of the melt. Tc(VII) in oxide glasses is normally assumed to be isolated pertechnetate TcO 4 - anions surrounded by alkali, but can occasionally precipitate as alkali pertechnetate salts such as KTcO 4 and NaTcO 4 when Tc concentration is high. In these cases, Tc(VII) is 4-coordinated by oxygen. A reinvestigation of the chemistry of alkali-technetium-oxides formed under oxidizing conditions and at temperatures used to prepare nuclear waste glasses showed that higher coordinated alkali Tc(VII) oxide species had been reported, including those with the TcO 5 - and TcO 6 - anions. The chemistry of alkali Tc(VII) and other alkali-Tc-oxides is reviewed, along with relevant synthesis conditions. Additionally, we report attempts to make 5- and 6-coordinate pertechnetate compounds of K, Na, and Li, i.e. TcO 5 - and TcO 6 -. It was found that higher coordinated species are very sensitive to water, and easily decompose into their respective pertechnetates. It was difficult to obtain pure compounds, but mixtures of the pertechnetate and other phase(s) were frequently found, as evidenced by x-ray absorption spectroscopy (XAS), neutron diffraction (ND), and Raman spectroscopy. Low temperature electron paramagnetic resonance (EPR) measurements showed the possibility of Tc(IV) and Tc(VI) in Na 3 TcO 5 and Na 5 TcO 6 compounds. Here, it was hypothesized that the smaller counter cation would result in more stable pertechnetates. To confirm the synthesis method, LiReO 4 and Li 5 ReO 6 were prepared, and their Raman spectra match those in the literature. Subsequently, the Tc versions LiTcO 4 and Li 5 TcO 6 were synthesized and characterized by ND, Raman spectroscopy, XANES, and EXAFS. The Li 5 TcO 6 was a marginally stable compound that appears to have the same structure as that known for Li 5 ReO 6 . Implications of the experimental work on stability of alkali technetate compounds and possible role in the volatilization of Tc are discussed.

36 MATERIALS SCIENCE↗

Overview of waste heat utilization systems

The heavy truck diesel engine rejects a significant fraction of its fuel energy in the form of waste heat. Historically, the Department of Energy has supported technology efforts for utilization of the diesel exhaust heat. Specifically, the Turbocompound and the Organic Rankine Cycle System (ORCS) have demonstrated that meaningful improvements in highway fuel economy can be realized through waste heat utilization. For heat recovery from the high temperature exhaust of future adiabatic diesel engines, the DOE/NASA are investigating a variety of alternatives based on the Rankine, Brayton, and Stirling power cycles. Initial screening results indicate that systems of this type offer a fuel savings advantage over the turbocompound system. Capital and maintenance cost projections, however, indicate that the alternative power cycles are not competitive on an economic payback basis. Plans call for continued analysis in an attempt to identify a cost effective configuration with adequate fuel savings potential.

Bailey, M. M.↗

PARTNERSHIP FOR THE DEVELOPMENT OF NEXT GENERATION SIMULATION TOOLS TO EVALUATE CEMENTITIOUS BARRIERS AND MATERIALS USED IN NUCLEAR APPLICATION - 8388

The US DOE has initiated a multidisciplinary cross cutting project to develop a reasonable and credible set of tools to predict the structural, hydraulic and chemical performance of cement barriers used in nuclear applications over extended time frames (e.g., > 100 years for operating facilities and > 1000 years for waste management). A partnership that combines DOE, NRC, academia, private sector, and international expertise has been formed to accomplish the project objectives by integrating existing information and realizing advancements where necessary. The set of simulation tools and data developed under this project will be used to evaluate and predict the behavior of cementitious barriers used in near surface engineered waste disposal systems, e.g., waste forms, containment structures, entombments and environmental remediation, including decontamination and decommissioning (D&D) activities. The simulation tools will also support analysis of structural concrete components of nuclear facilities (spent fuel pools, dry spent fuel storage units, and recycling facilities, e.g., fuel fabrication, separations processes). Simulation parameters will be obtained from prior literature and will be experimentally measured under this project, as necessary, to demonstrate application of the simulation tools for three prototype applications (waste form in concrete vault, high level waste tank grouting, and spent fuel pool). Test methods and data needs to support use of the simulation tools for future applications will be defined. This is a national issue that affects all waste disposal sites that use cementitious waste forms and structures, decontamination and decommissioning activities, service life determination of existing structures, and design of future public and private nuclear facilities. The problem is difficult because it requires projecting conditions and responses over extremely long times. Current performance assessment analyses show that engineered barriers are typically the primary control to prevent the release of radionuclides from nuclear facilities into the environment. In the absence of an adequate predictive tool, assessments cannot fully incorporate the effectiveness of the concrete barriers, and the inventory of radionuclides (especially the long-lived radionuclides) that may be safely disposed of in shallow land disposal and the predicted service life of operating nuclear facilities. This project is 5 year effort focused on reducing uncertainties associated with current methodologies for assessing cementitious barrier performance and increasing the consistency and transparency of the assessment process. The results of this project will enable improved risk-informed, performance-based decision making, and supports several of the strategic initiatives in the DOE-EM Engineering & Technology Roadmap.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Level Waste Remote Handling Equipment in the Melter Cave Support Handling System at the Hanford Waste Treatment Plant

Cold war plutonium production led to extensive amounts of radioactive waste stored in tanks at the Department of Energy's (DOE) Hanford site. Bechtel National, Inc. is building the largest nuclear Waste Treatment Plant in the world located at the Department of Energy's Hanford site to immobilize the millions of gallons of radioactive waste. The site comprises five main facilities; Pretreatment, High Level Waste vitrification, Low Active Waste vitrification, an Analytical Lab and the Balance of Facilities. The pretreatment facilities will separate the high and low level waste. The high level waste will then proceed to the HLW facility for vitrification. Vitrification is a process of utilizing a melter to mix molten glass with radioactive waste to form a stable product for storage. The melter cave is designated as the High Level Waste Melter Cave Support Handling System (HSH). There are several key processes that occur in the HSH cell that are necessary for vitrification and include: feed preparation, mixing, pouring, cooling and all maintenance and repair of the process equipment. Due to the cell's high level radiation, remote handling equipment provided by PaR Systems, Inc. is required to install and remove all equipment in the HSH cell. The remote handling crane is composed of a bridge and trolley. The trolley supports a telescoping tube set that rigidly deploys a TR 4350 manipulator arm with seven degrees of freedom. A rotating, extending, and retracting slewing hoist is mounted to the bottom of the trolley and is centered about the telescoping tube set. Both the manipulator and slewer are unique to this cell. The slewer can reach into corners and the manipulator's cross pivoting wrist provides better operational dexterity and camera viewing angles at the end of the arm. Since the crane functions will be operated remotely, the entire cell and crane have been modeled with 3-D software. Model simulations have been used to confirm operational and maintenance functional and timing studies throughout the design process. Since no humans can go in or out of the cell, there are several recovery options that have been designed into the system including jack-down wheels for the bridge and trolley, recovery drums for the manipulator hoist, and a wire rope cable cutter for the slewer jib hoist. If the entire crane fails in cell, the large diameter cable reel that provides power, signal, and control to the crane can be used to retrieve the crane from the cell into the crane maintenance area. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Materials Science of High-Level Nuclear Waste Immobilization

With the increasing demand for the development of more nuclear power comes the responsibility to address the technical challenges of immobilizing high-level nuclear wastes in stable solid forms for interim storage or disposition in geologic repositories. The immobilization of high-level nuclear wastes has been an active area of research and development for over 50 years. Borosilicate glasses and complex ceramic composites have been developed to meet many technical challenges and current needs, although regulatory issues, which vary widely from country to country, have yet to be resolved. Cooperative international programs to develop advanced proliferation-resistant nuclear technologies to close the nuclear fuel cycle and increase the efficiency of nuclear energy production might create new separation waste streams that could demand new concepts and materials for nuclear waste immobilization. This article reviews the current state-of-the-art understanding regarding the materials science of glasses and ceramics for the immobilization of high-level nuclear waste and excess nuclear materials and discusses approaches to address new waste streams.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The future of waste management and reduction shows promise with technological advances that have sparked newer and more efficient methods

The safe, clean, and efficient reduction and management of both radioactive and nonradioactive wastes are essential processes, however, these processes can be time consuming, complicated, and costly. The goal of this poster is to research possible waste solutions that will encourage the use of more environmentally and monetarily efficient methods of waste disposal, and decrease the amount of hazardous waste bound for energy recovery, treatment, and disposal facilities. Technological advances such as smart trash bins provide a more efficient means of disposing solid wastes and encouraging recycling. Using artificial intelligence, these bins are able to categorize and separate different forms of waste and recyclable material. The smart bins also provide a method for ensuring the most efficient pick up times for waste facilities. This is done with the use of trash bin sensors, thus, overtime saving money and reducing CO2 emissions. Some countries are also finding ways on a larger scale to reduce waste and encourage environmentally friendly practices. Facilities are reducing waste output through waste recycling, and they are using the waste-to-energy techniques to supply cities with the majority of needed energy. The adoption and encouragement of technological advances in waste reduction and energy restoration can lead to a diminished need for hazardous waste treatment plants, and have a significant impact on preserving our resources, protecting the environment, and simultaneously reducing costs over time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CETE R&D at Oak Ridge National Laboratory Supporting Management of Nuclear Waste - 9227

Oak Ridge National Laboratory (ORNL) is conducting a complete, coupled end-to-end (CETE) demonstration of advanced nuclear fuel reprocessing to support the Advanced Fuel Cycle Initiative (AFCI) Research and Development Program. The CETE project under way at ORNL is focused on (1) the demonstration of separations technology that would significantly reduce the quantity of nuclear waste that would require long-term geologic disposal and (2) providing products and waste streams for further treatment and testing to develop suitable forms for recycle or disposal. Equipment for the CETE research and development (R&D) capability has been installed to provide all primary processing operations, ranging from spent fuel receipt to production of products and waste forms. The head-end treatment and off-gas recovery as well as the various solvent extraction processes separate the spent fuel into a number of discrete product streams, each with unique properties. As part of the CETE project demonstrations at ORNL, each of these product streams is recovered to serve as the feed to other critical process and waste management research, development, and demonstration activities. These include the production of recycle MOX fuel, transmutation fuels, recycle cladding, and new waste forms. The paper discusses the separation and recovery processes used in the CETE demo and the resulting products from the first campaign.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Gas retention and release from Hanford Site sludge waste tanks - 15491

Radioactive wastes from nuclear fuel processing are stored in large underground storage tanks at the Hanford Site. Solid wastes can be divided into salt-cake (mostly precipitated soluble sodium nitrate and nitrite salts with some interstitial liquid consisting of concentrated salt solutions) and sludge (mostly low solubility aluminum and iron compounds with relatively dilute interstitial liquid). Waste generates hydrogen through the radiolysis of water and organic compounds, radio-thermolytic decomposition of organic compounds, and corrosion of a tank's carbon steel walls. Nonflammable gases, such as nitrous oxide and nitrogen, are also produced. Additional flammable gases (e.g., ammonia and methane) are generated by chemical reactions between various degradation products of organic chemicals present in the tanks. Six double-shell tanks (DSTs) containing salt-cake wastes began showing signs of gas accumulation and buoyant instability in the form of periodic waste level drops in the 1980's. Studies in the 1990's indicated that gas would accumulate in the settled solids layer until its bulk density was lower than the supernatant liquid. The resultant gas release caused by this instability was termed a Buoyant Displacement Gas Release Event (BDGRE). Criteria were developed to prevent forming additional waste tanks that exhibited BDGREs. Significant gas accumulation and BDGREs were never observed in tanks containing predominantly sludge wastes. Literature reviews, data from Hanford Site waste tanks, and experiments with waste simulants have led to new conclusions on gas retention and release in sludge waste. The data show similar overall behavior where initially the settled solids volume increases as gas bubbles form. Gas fraction in the settled solids increases to a peak concentration after which additional generated gas escapes through connected cracks and there is a balance between gas generation and gas release with little change in gas fraction. Experiments showed that this behavior does not change as sludge waste depth increases. Sufficient data now exist to differentiate between gas retention and release behavior in Hanford Site sludge waste tanks and salt-cake waste tanks. The salt-cake criteria do not need to be applied to sludge waste tanks that exhibit certain gas retention and release behavior. Criteria for waste characteristics and process behavior have been defined that identify specific wastes and tanks that, based on previous operating experience, will have low gas retention and will not exhibit large, spontaneous releases. The first criterion defines what waste is considered sludge and what waste is considered salt-cake. If the mass ratio of soluble to insoluble constituents is below 2.5, then the waste is sludge. The second criterion is a density difference criterion that prevents tanks being operated in a region where sludge buoyancy might occur. For large gas releases to occur, the settled solids must accumulate sufficient gas to become less dense than the overlying supernatant (i.e., the settled solids would become buoyant). Based on previous operating experience, the ratio of liquid density to degassed settled solids bulk density (ρl/ρB) should be maintained at ≤ 0.84. This ensures that retained gas content in the sludge would need to exceed 16% by volume for the settled solids to become buoyant in the overlying supernatant. Tank waste that satisfies the mass ratio criterion, the liquid to bulk solids density criterion, and has process data supporting typical Hanford waste sludge behavior does not pose a significant risk for a large spontaneous gas release event. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Viscosity of glass-forming melt at the bottom of high-level waste melter feed cold caps: Effects of temperature and incorporation of solid components

At the final stages of conversion of melter feed (glass batch) to molten glass, the transient glass-forming melt becomes a continuous liquid phase encapsulating dissolving solid particles and gas bubbles that produce primary foam at the bottom of the cold cap (the reacting melter feed in an electric glass melting furnace). The glass-forming melt viscosity plays a dominant role in primary foam formation, stability, and eventual collapse, thus affecting the rate of melting (the glass production rate per cold cap area). For several melter feeds designed for nuclear waste vitrification, we have traced the glass-forming melt viscosity during the final stages of feed-to-glass conversion as it changes in response to changing temperature and composition (resulting from dissolving solid particles). Starting with a relatively low values at the moment when the melt connects, melt viscosity reaches maximum within the primary foam layer and then decreases to its final melter-operating temperature value. We paid a particular attention to the cold-cap bottom—the boundary between the primary foam layer and the thermal boundary layer—where the melt viscosity affects the rate of melting predominantly through its effect on the temperature at which primary foam is collapsing.

Lee, Seung Min↗

Evaluation of Heavy Metals in Solid Waste Disposal Sites in Campinas City, Brazil Using Synchrotron Radiation Total Reflection X-Ray Fluorescence

The problem of solid waste in most countries is on the rise as a result of rapid population growth, urbanization, industrial development and changes in consumption habits. Amongst the various forms of waste disposals, landfills are today the most viable for the Brazilian reality, both technically and economically. Proper landfill construction practices allow minimizing the effects of the two main sources of pollution from solid waste: landfill gas and slurry. However, minimizing is not synonymous with eliminating; consequently, the landfill alone cannot resolve all the problems with solid waste disposal. The main goal of this work is to evaluate the content of trace elements in samples of groundwater, surface water and slurry arising from local solid waste disposals in the city of Campinas, SP, Brazil. Samples were collected at the Delta, Santa Barbara and Pirelli landfills. At the Delta and Santa Barbara sites, values above the maximum permitted level established by CETESB for Cr, Mn, Fe, Ni and Pb were observed in samples of groundwater, while at the Pirelli site, elements with concentrations above the permitted levels were Mn, Fe, Ba and Pb. At Delta, values above levels permitted by the CONAMA 357 legislation were still observed in surface water samples for Cr, Mn, Fe and Cu, whereas in slurry samples, values above the permitted levels were observed for Cr, Mn, Fe, Ni, Cu, Zn and Pb. Slurry samples were prepared in accordance with two extraction methodologies, EPA 3050B and EPA 200.8. Concentrations of Cr, Ni, Cu and Pb were higher than the limit established by CONAMA 357 for most samples collected at different periods (dry and rainy) and also for the two extraction methodologies employed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An environmental friendly animal waste disposal process with ammonia recovery and energy production: Experimental study and economic analysis

Highlights: • An environmental friendly animal manure waste treatment scheme was proposed. • Ammonia was removed and recovered from manure waste in the form of struvite. • Horse manure waste gasification was successfully conducted in a 10 kW gasifier. • Gasifier produces comparable or higher heating value of syngas as other feedstocks. • The proposed scheme is financially superior to pure gasification and incineration. - Abstract: Animal manure waste is considered as an environmental challenge especially in farming areas mainly because of gaseous emission and water pollution. Among all the pollutants emitted from manure waste, ammonia is of greatest concern as it could contribute to formation of aerosols in the air and could hardly be controlled by traditional disposal methods like landfill or composting. On the other hand, manure waste is also a renewable source for energy production. In this work, an environmental friendly animal waste disposal process with combined ammonia recovery and energy production was proposed and investigated both experimentally and economically. Lab-scale feasibility study results showed that 70% of ammonia in the manure waste could be converted to struvite as fertilizer, while solid manure waste was successfully gasified in a 10 kW downdraft fixed-bed gasifier producing syngas with the higher heating value of 4.9 MJ/(N m{sup 3}). Based on experimental results, economic study for the system was carried out using a cost-benefit analysis to investigate the financial feasibility based on a Singapore case study. In addition, for comparison, schemes of gasification without ammonia removal and incineration were also studied for manure waste disposal. The results showed that the proposed gasification-based manure waste treatment process integrated with ammonia recovery was most financially viable.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Savannah River Site Public and Regulatory Involvement in the Cercla Low-Level Waste (LLW) Program and Their Effect on Decisions to Dispose of LLW Generated by Cercla

The key to successful public involvement at the Savannah River Site (SRS) has been and continues to be vigorous, up-front involvement of the public, federal and state regulators with technical experts. The SRS Waste Management Program includes all forms of radioactive waste. All of the decisions associated with the management of these wastes are of interest to the public and successful program implementation would be impossible without including the public up-front in the program formulation. Serious problems can result if program decisions are made without public involvement, and if the public is informed after key decisions are made. This paper will describe the regulatory and public involvement program and their effects on the decisions concerning the disposal at the Savannah River Site (SRS) of LLW generated from CERCLA Removal and Remedial Actions. At SRS the Deactivation and Decommissioning (D and D) project has generated large amounts of LLW from the removal of buildings and processing facilities. The D and D project is expected to generate even larger amounts of LLW in the future. The most cost effective disposal alternated is to use the onsite LLW disposal facility in E-Area. The E-Area LLW Facility is owned and operated by the Department of Energy (DOE) under its authority granted by the Atomic Energy Act of 1954, as amended. Since the disposal of CERCLA generated waste is also governed by the Environmental Protection Agency (EPA) CERCLA regulations, it is important that EPA, DOE, and the South Carolina Department of Health and Environmental Control (SCDHEC) work together to resolve any conflicts in implementation of the D and D project so that all regulations are followed and the project can be continued successfully. An issue of particular significance will be described in this paper that, were it not resolved successfully, would have jeopardized the completion of one project and resulted in higher overall project costs. The EPA determined in review of the E-Area LLW Facility groundwater monitoring that a 'release' under CERCLA had occurred. As a result, EPA determined that it was necessary to issue a 'Notice of Unacceptability' to SRS revoking the CERCLA Off-Site Rule approval for the E-Area LLW Facility, thus, no longer allowing the E-Area LLW Facility Slit trenches to receive CERCLA waste for disposal. It became critical to the success of the D and D project to reestablish CERCLA Off-Site Rule approval. The discussions and negotiations Comment [HB1]: with the South Carolina regulators and EPA were conducted in full view of the public and as such, an informed decision as to resolution included the public interactions. This paper will describe the successful results of this technical, regulatory, and public involvement program, explore the challenges, how the accomplishments occurred, and describe the future challenges along with the road map for the future. In doing this, the SRS D and D project must be described to give the readers an understanding of the technical complexities that must be communicated successfully to achieve constructive stakeholder participation and regulatory approval. (author)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Ambivalent Role of Participants in Nuclear Waste Decisions - 16360

Today's global nuclear sector has entered a critical juncture. Waste management solutions have the potential to influence the prospects of whether new plants will be built and when aging plants will be decommissioned. Even in countries without nuclear power plants, the siting of nuclear waste can present communication challenges and opportunities for public involvement. As new nuclear programs withstand scrutiny, local communities share their want for solutions to nuclear waste before new plant construction commences. Developing nations have begun to explore the potential of adding nuclear power production to their energy mix. They carefully watch established nuclear players to accelerate their plans with lessons learned elsewhere. Some newcomers to nuclear energy will make decisions on new construction based on other operators' abilities to reconcile public concerns regarding radioactive waste. Distinct forms of government, cultural norms and means of public discourse present innovative approaches and changing expectations worldwide. This paper explores how practitioners are evaluating ways to activate stakeholders on nuclear waste siting in nations embarking on new nuclear programs. It investigates the incentives that people have to participate and legitimize the formation of laws, regulations and standards for nuclear materials management. Finally, it highlights examples of public participation techniques from established operating environments and posits that overly prescriptive requirements for stakeholder engagement can reduce the authenticity of public involvement and weaken confidence among participants in the decision making process. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Glass formulation and lab-scale testing of glasses designed for in-can Melter and in-container Vitrification of high-assay low-enriched uranium aqueous polishing Raffinate waste

Glasses were designed for processing a nuclear waste from aqueous polishing of high-assay low-enriched uranium using either In-Can Melter (ICM) or GeoMelt® In-Container Vitrification™ (ICV) technologies, which operate at temperatures of T p ≤ 1100 °C and T p ≤ 1450 °C, respectively. Due to the different operating conditions, the melt and glass properties were optimized differently for each technology. Each glass was designed to optimize for maximum waste loading while simultaneously satisfying processing (e.g., crystallization, viscosity, and conductivity) and product quality (e.g., durability, hazard characteristic, and crystal content) constraints. Here, the raffinate waste contains high nitric acid (4 M) and low total solids (9 g·L -1 ) concentrations. Feed preparation processes were tested to facilitate concentration and nitrate destruction/removal while controlling redox of the melter feed. A successful feed process including sugar addition and spray-drying was performed to generate an adequate melter feed for ICV processing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A tough and sustainable fiber-forming material from lignin and waste poly(ethylene terephthalate)

In this report we describe repurposing of recycled polyesters as a matrix for lignin-a biorefinery coproduct that is used as a solid fuel and needs to find higher value-to make sustainable high-performance thermoplastic materials. Brittle lignin oligomers, isolated from plant biomass, require a low-melting host polymer matrix to form a rigid and tough renewable material. We demonstrate controlled lignin dispersion and interfacial interactions in softened recycled polyethylene terephthalate (PET) using a simple solvent-free, melt-blending technique. To avoid lignin degradation and devolatilization during melt processing, it was thermally treated. Tall oil fatty acid was used to enable PET processability at low enough temperature to accommodate lignin without charring. Chemical analysis reveals reduction of aliphatic hydroxyl content from 2 mmol g –1 to 1.63 mmol g –1 and an increase of total phenolic hydroxyl moieties from 5.86 to 6.64 mmol g –1 and cleavage of β-O-4 ether linkages due to thermal treatment. Structural transformation of lignin macromolecules during heat treatment was further confirmed by an increase in molar mass and improved thermal stability. Interfacial interactions between lignin and PET were assessed from mechanical properties and thermal analyses. Thermal treatment not only helps to improve the stability of lignin but also slightly reduces the size of the dispersed lignin domains via favored interfacial interactions with the PET matrix. These methods improve mechanical properties of the material. Further, incorporation of lignin in the plasticized PET matrix increases the ductility in the blended products. Here, the method we discuss here utilizes industrial wastes and co-products, and it does not require solvent or toxic chemicals during the reactive extrusion process that yields complete conversion to products.

36 MATERIALS SCIENCE↗

Waste treatment in silicon production operations

A battery of special burners, each adapted for the treatment of a particular range of waste material formed during the conversion of metallurgical grade silicon to high purity silane and silicon, is accompanied by a series arrangement of filters to recover fumed silica by-product and a scrubber to recover muriatic acid as another by-product. All of the wastes are processed, during normal and plant upset waste load conditions, to produce useful by-products in an environmentally acceptable manner rather than waste materials having associated handling and disposal problems.

Coleman, Larry M.↗

An Assessment of Using Vibrational Compaction of Calcined HLW and LLW in DWPF Canisters

Since 1963, the INEL has calcined almost 8 million gallons of liquid mixed waste and liquid high-level waste, converting it to some 1.1 million gallons of dry calcine (about 4275.0 m3), which consists of alumina-and zirconia-based calcine and zirconia-sodium blend calcine. In addition, if all existing and projected future liquid wastes are solidified, approximately 2,000 m3 of additional calcine will be produced primarily from sodium-bearing waste. Calcine is a more desirable material to store than liquid radioactive waste because it reduces volume, is much less corrosive, less chemically reactive, less mobile under most conditions, easier to monitor and more protective of human health and the environment. This paper describes the technical issue involved in the development of a feasible solution for further volume reduction of calcined nuclear waste for transportation and long term storage, using a standard DWPF canister. This will be accomplished by developing a process wherein the canisters are transported into a vibrational machine, for further volume reduction by about 35%. The random compaction experiments show that this volume reduction is achievable. The main goal of this paper is to demonstrate through computer modeling that it is feasible to use volume reduction vibrational machine without developing stress/strain forces that will weaken the canister integrity. Specifically, the paper presents preliminary results of the stress/strain analysis of the DWPF canister as a function of granular calcined height during the compaction and verifying that the integrity of the canister is not compromised. This preliminary study will lead to the development of better technology for safe compactions of nuclear waste that will have significant economical impact on nuclear waste storage and treatment. The preliminary results will guide us to find better solutions to the following questions: 1) What are the optimum locations and directions (vertical versus horizontal or both of them) of applying the vibrational forces? 2) What is best mode of operation: first fill the canister with calcined waste and then vibrate it and refill it again, or apply vibrational forces during the filling process. By optimum or best we mean less creation of stress/strain forces during the volume reduction vibration process. Lessons learnt: This preliminary study shows that; 1) The maximum stress concentration always occurs in the canister wall, however its location varies and depends on the loading condition, and vibration process. 2) The proposed vibrational process would not cause any damages to the granulated calcined waste. 3) The first natural frequency of the longitudinal vibration of the canister is around 400 Hz, which is far away from the applied vibrational frequencies and from possibility of resonance phenomena that may cause damage to the canister 4) The relationship between the maximum internal stress and the frequency of the applied load is not parabolic. 5) The mechanical properties of the granulated calcined nuclear waste have small impact on the internal stress of the canister. Finally, the calculated data suggested that applying vibrational forces will keep the entire canister whole without any indication of development defects, and will have significant economical benefits of handling HLW and LLW in calcined forms, from waste manipulation, storage and transportation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗