Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗

Morphological evolution of Ag2Te precipitates in thermoelectric PbTe.

Nanostructuring of thermoelectric materials is expected to enhance thermoelectric properties by reducing the thermal conductivity and improving the power factor from that of homogeneous bulk materials. In multiphase, nanostructured thermoelectric materials, an understanding of precipitation mechanisms and phase stability is crucial for engineering systems with optimal thermoelectric performance. In this presentation we will discuss our investigations of the morphological evolution, orientation relationship, and composition of Ag{sub 2}Te precipitates in PbTe using transmission electron microscopy (TEM) and atom probe tomography (APT). Annealing in the region of two phase equilibrium between Ag{sub 2}Te and PbTe results in the formation of monoclinic {beta}-Ag{sub 2}Te precipitates as determined by x-ray and electron diffraction studies. These precipitates are aligned to the PbTe matrix with an orientation relationship that aligns the Te sub-lattices in the monoclinic and rock salt structures. This relationship is the same as we have reported earlier for {beta}-Ag{sub 2}Te precipitates in rocksalt AgSbTe{sub 2}. Observations using TEM and APT suggest that the Ag{sub 2}Te precipitates initially form as coherent spherical precipitates which upon coarsening evolve into flattened semi-coherent disks along the <100>PbTe directions which is consistent with theoretical predictions for elastically strained precipitates in a matrix. Our HRTEM observations show that sufficiently small precipitates are coherently embedded, while larger precipitates exhibit misfit dislocations and multiple monoclinic variants to relieve the elastic strain. Analysis of the composition of both precipitate groups using APT indicates that the larger precipitates exhibit compositions close to equilibrium while the smaller nanoscale precipitates exhibit enhanced Pb compositions. This detailed analysis of the orientation relationship, morphology, composition, and coarsening behavior of embedded Ag{sub 2}Te precipitates may be helpful in understanding the precipitation mechanisms and microstructure of related thermoelectric materials, such as LAST.

36 MATERIALS SCIENCE↗

MADE3D: Enabling the Next-Generation High-Torque- Density Wind Generators by Additive Design and 3D Printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments - especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technologies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

3D printing↗

Muconic Acid Production from P. putida Using High Protein Algae Hydrolysate

The composition of algal biomass is highly dynamic, with protein, lipid, and carbohydrate contents varying in response to nutrient and environmental conditions during cultivation. Because shifts in biomass composition are often associated with reduced biomass productivity, production costs can often increase if targeting higher biomass compositional quality (enriched in carbohydrates or lipids at reduced protein content) as input for the algal biorefinery. The optimal algal biorefinery configuration is thus a function of many factors. One of the key strengths of the Combined Algal Processing (CAP) process is the versatility of feedstocks and products produced. The concept has been demonstrated with ethanol and a variety of carboxylic acids (succinic, butyric, muconic) as coproducts along with lipid upgrading to biofuel. Modification of the approaches, processes and downstream upgrading to fuels has allowed the CAP process to reduce costs and improve efficiency. Muconic acid is a high-value, potential fermentation coproduct of interest because it can be easily converted to adipic acid, a high-volume monomer for the production of nylon and other valuable consumer plastics. As such, the production of muconic acid through CAP was explored to expand the suite of products from algal biomass and to begin exploring the valorization of high protein content biomass from rapidly grown algae biomass. We have established initial performance parameters and shown that the range of substrates consumed by the muconic acid-producing microbe, Pseudomonas putida, includes at least glucose, mannose, glycerol, and lactic acid. We achieved complete utilization of these four major hydrolysate substrates achieving productivities of 0.037 (g/L/h) from Scenedesmus obliquus and 0.029 (g/L/h) from Monoraphidium minutum hydrolysates. Final titer and process yield (mol of muconic acid per mol of substrate (molP/molS)) were 0.99 g/L and 0.42 molP/molS from S. obliquus hydrolysate and 0.75 g/L and 0.23 molP/molS from M. minutum hydrolysate, respectively.

BIOMASS FUELS↗

Fabrication and Scale-Up of Porous Polybenzimidazole (PBI) Supports for Gas Separation Composite Membranes

Industrial gas separation often uses thin film composite (TFC) membranes comprising a porous support overlaid with a single-/multi-layer gas-selective thin film. An optimal porous support should possess high surface porosity to minimize gas transport resistance and nano-sized pores to ease pore penetration occurring during the thin film coating process. Good chemical and thermal stabilities are essential to withstand the aggressive solvents and heat required for the thin film coating and curing. However, few porous membranes satisfy all these requirements. This study presents a scalable membrane formation method of making highly porous polybenzimidazole (PBI) supports via non-solvent induced phase separation. This presentation also details the scale-up fabrication of PBI supports using a custom roll-to-roll membrane casting machine.

gas separation↗

TEM Characterization of Neutron Irradiated HfAl3-Al Composite Specimens

Particles comprised of a thermal neutron absorbing material (HfAl3) are dispersed in a metal matrix material with high thermal conductivity (aluminum) to conduct the heat generated by neutron capture away from the fuel and materials. This metal matrix composite is very promising for use as a conduction-cooled neutron absorber and has the potential to be useful as a shroud or heat sink for testing advanced fast reactor fuels and materials in an existing thermal reactor. To design and optimize the absorber block system for advanced reactor designs, fundamental understanding of the irradiation effect on material properties is necessary. This dataset contains TEM characterization results of neutron irradiated HfAl3-Al composite specimens. It is focused on the irradiation induced defects (dislocation lines and loops) characterization using the on-zone axis bright field STEM technique. This data was collected using a FEI Tecnai G2 F30 S/TEM at the Microscopy and Characterization Suite (MaCS), Center for Advanced Energy Studies (CAES).

Guillen, Donna↗

TEM Characterization of Neutron Irradiated HfAl3-Al Composite Specimens

Particles comprised of a thermal neutron absorbing material (HfAl3) are dispersed in a metal matrix material with high thermal conductivity (aluminum) to conduct the heat generated by neutron capture away from the fuel and materials. This metal matrix composite is very promising for use as a conduction-cooled neutron absorber and has the potential to be useful as a shroud or heat sink for testing advanced fast reactor fuels and materials in an existing thermal reactor. To design and optimize the absorber block system for advanced reactor designs, fundamental understanding of the irradiation effect on material properties is necessary. This dataset contains TEM characterization results of neutron irradiated HfAl3-Al composite specimens. It is focused on the irradiation induced defects (dislocation lines and loops) characterization using the on-zone axis bright field STEM technique. This data was collected using a FEI Tecnai G2 F30 S/TEM at the Microscopy and Characterization Suite (MaCS), Center for Advanced Energy Studies (CAES).

Guillen, Donna↗

Materials for Automotive Lightweighting

Reducing the weight of automobiles is a major contributor to increased fuel economy. The baseline materials for vehicle construction, low-carbon steel and cast iron, are being replaced by materials with higher specific strength and stiffness: advanced high-strength steels, aluminum, magnesium, and polymer composites. We find that the key challenge is to reduce the cost of manufacturing structures with these new materials. Maximizing the weight reduction requires optimized designs utilizing multimaterials in various forms. This use of mixed materials presents additional challenges in joining and preventing galvanic corrosion.

36 MATERIALS SCIENCE↗

Optimizing the fabrication process and interplay of device components of polymer solar cells using a field-based multiscale solar-cell algorithm

Both the device composition and fabrication process are well-known to crucially affect the power conversion efficiency of polymer solar cells. Major advances have recently been achieved through the development of novel device materials and inkjet printing technologies, which permit to improve their durability and performance considerably. In this work, we demonstrate the usefulness of a recently developed field-based multiscale solar-cell algorithm to investigate the influence of the material characteristics, like, e.g., electrode surfaces, polymer architectures, and impurities in the active layer, as well as post-production treatments, like, e.g., electric field alignment, on the photovoltaic performance of block-copolymer solar-cell devices. Our study reveals that a short exposition time of the polymer bulk heterojunction to the action of an external electric field can lead to a low photovoltaic performance due to an incomplete alignment process, leading to undulated or disrupted nanophases. With increasing exposition time, the nanophases align in direction to the electric field lines, resulting in an increase of the number of continuous percolation paths and, ultimately, in a reduction of the number of exciton and charge-carrier losses. Moreover, we conclude by modifying the interaction strengths between the electrode surfaces and active layer components that a too low or too high affinity of an electrode surface to one of the components can lead to defective contacts, causing a deterioration of the device performance. Finally, we infer from the study of block-copolymer nanoparticle systems that particle impurities can significantly affect the nanostructure of the polymer matrix and reduce the photovoltaic performance of the active layer. For a critical volume fraction and size of the nanoparticles, we observe a complete phase transformation of the polymer nanomorphology, leading to a drop of the internal quantum efficiency. For other particle-numbers and -sizes, we observe only a local perturbation of the nanostructure, diminishing the number of continuous percolation paths to the electrodes and, therefore, reducing the device performance. From these investigations, we conclude that our multiscale solar-cell algorithm is an effective approach to investigate the impact of device materials and post-production treatments on the photovoltaic performance of polymer solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Reaction Kinetics on Graphene-Edge Morphology and Composition

New simulations of graphene growth in flame environments are presented. The simulations employed a kinetic Monte Carlo (KMC) algorithm coupled to molecular mechanics (MM) geometry optimization to track individual graphenic species as they evolve. Focus was given to incorporation of five-member rings and resulting curvature and edge defects. The model code was re-written to be more computationally efficient enabling a larger set of simulations to be run, decreasing stochastic fluctuations in the averaged results. The model also included updated rate coefficients for graphene edge reactions recently published in the literature. Sensitivity analysis, enabled by the more efficient coding, confirmed the importance of the updated rates as well as providing further insight on key reactions controlling layer growth and morphology. The new KMC code was applied to simulate graphene-layer growth in the environments of laminar premixed flames. Finally, in these flame simulations, C-H ratios of evolving structures were computed and compared to those from experiment and from an alternate model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel Gas Composition Sensor for Monitoring Advanced Power Generation Systems

Power generation based on combustion will be an important part of American energy production for the foreseeable future. Optimization of the combustion process to maximize fuel efficiency and minimize harmful emissions will benefit from sensors capable of withstanding the harsh high pressure and high temperature environment typically found in the chamber. These devices must be versatile and easy to use with low probe cost in order to gain widespread acceptance and use. Physical Sciences Inc. and the research group of Prof. Scott Sanders at the University of Wisconsin have designed and demonstrated a novel sensor system for monitoring the concentration of multiple gas species in power generation systems. The system combines a novel laser from the optical telecommunications industry with a high-temperature measurement probe, sensitive detection electronics, and data processing algorithms. The Phase I program resulted in a successful demonstration of broadband spectroscopy combined with sensitive detection and chemometric algorithms to detect multiple gas species at high temperatures and pressures. A novel optical probe based on a sapphire fiber architecture that is compatible with the conditions expected in coal gasification systems was also designed. The initial target application for the proposed sensor is the monitoring of full scale, advanced power generation systems including coal gasifiers and gas turbines. The technology developed in this work may also be applied to many additional industrial processes, including continuous emission monitoring, pharmaceutical manufacturing and explosives detection. The ability to identify multiple species and measure their concentrations in a gas mixture will allow manufacturers to increase yields and reduce costs.

20 FOSSIL-FUELED POWER PLANTS↗

Optimizing algal cultivation & productivity : an innovative, multidiscipline, and multiscale approach.

Progress in algal biofuels has been limited by significant knowledge gaps in algal biology, particularly as they relate to scale-up. To address this we are investigating how culture composition dynamics (light as well as biotic and abiotic stressors) describe key biochemical indicators of algal health: growth rate, photosynthetic electron transport, and lipid production. Our approach combines traditional algal physiology with genomics, bioanalytical spectroscopy, chemical imaging, remote sensing, and computational modeling to provide an improved fundamental understanding of algal cell biology across multiple cultures scales. This work spans investigations from the single-cell level to ensemble measurements of algal cell cultures at the laboratory benchtop to large greenhouse scale (175 gal). We will discuss the advantages of this novel, multidisciplinary strategy and emphasize the importance of developing an integrated toolkit to provide sensitive, selective methods for detecting early fluctuations in algal health, productivity, and population diversity. Progress in several areas will be summarized including identification of spectroscopic signatures for algal culture composition, stress level, and lipid production enabled by non-invasive spectroscopic monitoring of the photosynthetic and photoprotective pigments at the single-cell and bulk-culture scales. Early experiments compare and contrast the well-studied green algae chlamydomonas with two potential production strains of microalgae, nannochloropsis and dunnaliella, under optimal and stressed conditions. This integrated approach has the potential for broad impact on algal biofuels and bioenergy and several of these opportunities will be discussed.

59 BASIC BIOLOGICAL SCIENCES↗

Controlled release of cortisone drugs from block copolymers synthetized by ATRP

Diseases affecting posterior eye segment, like macular edema, infection and neovascularization, may cause visual impairment. Traditional treatments, such as steroidal-drugs intravitreal injections, involve chronic course of therapy usually over a period of years. Moreover, they can require frequent administrations of drug in order to have an adequately disease control. This dramatically reduce patient’s compliance. Efforts have been made to develop implantable devices that offer an alternative therapeutic approach to bypass many challenges of conventional type of therapy. Implantable drug delivery systems (DDS) have been developed to optimize therapeutic properties of drugs and ensure their slow release in the specific site. Polymeric materials can play an essential role in modulating drug delivery and their use in such field has become indispensable. During last decades, acrylic polymers have obtained growing interest. Biocompatibility and chemical properties make them extremely versatile, allowing their use in many field such as biomedical. In particular, block methacrylate copolymer with a balance of hydrophilic and hydrophobic properties can be suitable for prolonged DDS in biomedical devices. In this work, we focused on the realization of a system for controlled and long term release of betamethasone 17,21-dipropionate (BDP), a cortisone drug, from methacrylic block copolymers, to be tested in the treatment of the posterior eye’s diseases. Different series of methyl methacrylate/hydroxyethyl methacrylate (MMA/HEMA) block and random copolymers, with different monomer compositions (10–60% HEMA), were synthetized by Atom Transfer Radical Polymerization (ATRP) to find the best hydrophilic/hydrophobic ratio, able to ensure optimal kinetic release. Copolymer samples were characterized by NMR spectroscopy ({sup 1}H-NMR, {sup 13}C-NMR, CosY), SEC, TGA and DSC. Monitoring of drug release from films loaded with BDP was carried out by HPLC analysis. Evaluation of different kinetic models allowed to deduce that release of BDP is controlled over time from PMMA-b-PHEMA 53/47. In particular, PMMA-b-PHEMA 53/47 showed the best release profile to achieve the therapeutic reference dose of 3 µg/die, employed in treatment of posterior eye disease, up to four months. Accordingly, PMMA-b-PHEMA 53/47 has been tested to prepare ocular inserts. Ocular inserts with different shape and the same area of polymer films have been obtained using silicon moulds made by a 3D printer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

CT energy weighting in the presence of scatter and limited energy resolution

Purpose: Energy-resolved CT has the potential to improve the contrast-to-noise ratio (CNR) through optimal weighting of photons detected in energy bins. In general, optimal weighting gives higher weight to the lower energy photons that contain the most contrast information. However, low-energy photons are generally most corrupted by scatter and spectrum tailing, an effect caused by the limited energy resolution of the detector. This article first quantifies the effects of spectrum tailing on energy-resolved data, which may also be beneficial for material decomposition applications. Subsequently, the combined effects of energy weighting, spectrum tailing, and scatter are investigated through simulations. Methods: The study first investigated the effects of spectrum tailing on the estimated attenuation coefficients of homogeneous slab objects. Next, the study compared the CNR and artifact performance of images simulated with varying levels of scatter and spectrum tailing effects, and reconstructed with energy integrating, photon-counting, and two optimal linear weighting methods: Projection-based and image-based weighting. Realistic detector energy-response functions were simulated based on a previously proposed model. The energy-response functions represent the probability that a photon incident on the detector at a particular energy will be detected at a different energy. Realistic scatter was simulated with Monte Carlo methods. Results: Spectrum tailing resulted in a negative shift in the estimated attenuation coefficient of slab objects compared to an ideal detector. The magnitude of the shift varied with material composition, increased with material thickness, and decreased with photon energy. Spectrum tailing caused cupping artifacts and CT number inaccuracies in images reconstructed with optimal energy weighting, and did not impact images reconstructed with photon counting weighting. Spectrum tailing did not significantly impact the CNR in reconstructed images. Scatter reduced the CNR for all energy-weighting methods; however, the effect was greater for optimal energy weighting. For example, optimal energy weighting improved the CNR of iodine and water compared to energy-integrating weighting by a factor of {approx}1.45 in the absence of scatter and by a factor of {approx}1.1 in the presence of scatter (8.9 deg. cone angle, SPR 0.5). Without scatter correction, the difference in CNR resulting from photon-counting and optimal energy weighting was negligible (<15%) for cone angles greater than 4.4 deg. (SPR>0.3). Optimal weights combined with deterministic scatter correction provided a 1.3 and 1.1 improvement in CNR compared to energy-integrating and photon-counting weighting, respectively, for the 8.9 deg. cone angle simulation. In the absence of spectrum tailing, image-based weighting demonstrated reduced cupping artifact compared to projection-based weighting; however, both weighting methods exhibited similar cupping artifacts when spectrum tailing was simulated. There were no statistically significant differences in the CNR resulting from projection and image-based weighting for any of the simulated conditions. Conclusions: Optimal linear energy weighting introduces artifacts and CT number inaccuracies due to spectrum tailing. While optimal energy weighting has the potential to improve CNR compared to conventional weighting methods, the benefits are reduced as scatter increases. Efficient methods for reducing scatter and correcting spectrum tailing effects are required to obtain the highest benefit from optimal energy weighting.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗

Non-destructive Quantitative Phase Analysis and Microstructural Characterization of Zirconium Coated U-10Mo Fuel Foils via Neutron Diffraction

This report uses neutron diffraction to investigate the crystal phase composition of uranium-molybdenum alloy foils (U-10Mo) for the CONVERT MP-1 Reactor Conversion Project, and determines the effect on alpha-uranium contamination following the deposition of a Zr metal diffusion layer by various methods: plasma spray deposition of Zr powders at LANL and hot co-rolling with Zr foils at BWXT. In summary, there is minimal decomposition of the gamma phase U-10Mo foil to alpha phase contamination following both plasma spraying and hot co-rolling. The average unit cell volume, i.e. lattice spacing, of the Zr layer can be mathematically extracted from the diffraction data; co-rolled Zr matches well with literature values of bulk Zr, while plasma sprayed Zr shows a slight increase in the lattice spacing, indicative of interstitial oxygen in the lattice. Neutron diffraction is a beneficial alternative to conventional methods of phase composition, i.e. x ray diffraction (XRD) and destructive metallography. XRD has minimal penetration depth in high atomic number materials, particularly uranium, and can only probe the first few microns of the fuel plate; neutrons pass completely through the foil, allowing for bulk analysis of the foil composition and no issues with addition of cladding layers, as in the final, aluminum-clad reactor fuel plates. Destructive metallography requires skilled technicians, cutting of the foil into small sections, hazardous etching conditions, long polishing and microscopy times, etc.; the neutron diffraction system has an automated sample loader and can fit larger foils, so there is minimal analysis preparation; the total spectrum acquisition time is ~ 1 hour per sample. The neutron diffraction results are limited by spectra refinement/calculation times and the availability of the neutron beam source. In the case of LANSCE at Los Alamos, the beam operates ~50% of the year. Following the lessons learned from these preliminary results, optimizations to the process and analysis can be made, and neutron diffraction can become a viable and efficient technique for gamma/alpha phase composition determination for nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

End-to-end optimization for battery materials and molecules by combining graph neural networks and reinforcement learning

The National Renewable Energy Laboratory (NREL), together with the Colorado School of Mines (CSM) and Colorado State University (CSU), has developed a machine learning-enhanced approach to design new battery materials. Currently, such materials are designed in part via numerous expensive high-fidelity computational simulations that predict the performance of a given composition. Even with computational screening tools, the vast landscape of possible molecular or crystal structures exceeds current and future computational capacity. Improving the efficiency by which new materials can be optimized will therefore disrupt the cost, risk, and time required to bring new energy solutions to the marketplace. Predicting the properties of an organic molecule or periodic crystalline material given its structure has grown increasingly common. These approaches leverage large-scale computational and experimental databases and ML approaches such as graph neural networks. The inverse design problem of finding a material that possesses desired properties is substantially more challenging, since enumerating all valid material structures is not feasible. In this project, we leveraged recent success in reinforcement learning to efficiently navigate this high-dimensional search space. Just as algorithms can find the optimal chess moves from nearly limitless options, we train an approach to evolve a simple starting structure into a complex structure that possess the desired properties. Our solution has been demonstrated by applying it to two related design application tasks for short- and long-term energy storage, respectively: (1) the design of solid-state ion conductors and (2) the design of organic redox-active materials. The project has resulted an open-source software library for material design, documented examples of applying the library to both organic and inorganic material optimization, and peer-reviewed publications detailing the data, computational models, and resulting candidate materials.

25 ENERGY STORAGE↗

Performance investigation on a novel two-stage solar driven rotary desiccant cooling system using composite desiccant materials

In this study, a two-stage solar driven rotary desiccant cooling (TSRDC) system with novel configuration and newly developed silica gel-haloid composite desiccant is proposed aiming to reduce regeneration temperature and to achieve high energy performance. Simulated results show that there also exists an optimal rotation speed for TSRDC system. Compared with one-stage system, it is found that for the similar supply air state, the required regeneration temperature of TSRDC system is lower and for the same regeneration temperature, the cooling capacity of TSRDC is bigger. (author)

14 SOLAR ENERGY↗