Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

Implications of carbon content for the processing, stability, and mechanical properties of cast and wrought Ni-based superalloy Nimonic 105

As the temperature and pressure requirements in land-based turbines for power generation increase, the shift towards more advanced alloys, e.g., Ni-based superalloys, requires improved understanding of their long-term stability and mechanical properties. Additionally, the larger size of the components also presents fabrication and cost-reduction problems. In this study, we investigated Nimonic 105 as a potential rotor material at two carbon content levels – the commonly used maximum of the alloy specification and a lower carbon content variant. Reducing the carbon content presented fabrication challenges, resulting in surface crack formation during hot working. Additionally, a lower M 6 C carbide fraction was present after fabrication/solutioning, leading to a significantly larger grain size. After the standard aging treatment, similar γ' populations formed in the two variants, however the M 6 C carbides in the high-carbon variant already started transforming to intergranular M 23 C 6 . Although we did not observe a noticeable effect on the tensile properties of the two variants, the lower carbon content alloy possessed a superior creep property – mainly due to the larger grain size as the microstructural stability was inferior. Further, upon prolonged thermal exposure, the M 6 C carbides in the low-carbon variant further decomposed to intergranular and intragranular σ and μ precipitates, as opposed to mainly M 23 C 6 as in the high-carbon variant.

36 MATERIALS SCIENCE↗

Relationship between operational variables, fundamental physics and foamed cement properties in lab and field generated foamed cement slurries

Foamed cement is a critical component for wellbore stability. The mechanical performance of a foamed cement depends on its microstructure, which in turn depends on the preparation method and attendant operational variables. Determination of cement stability for field use is based on laboratory testing protocols governed by API Recommended Practice 10B-4 (API RP 10B-4, 2015). However, laboratory and field operational variables contrast considerably in terms of scale, as well as slurry mixing and foaming processes. Here in this paper, laboratory and field operational processes are characterized within a physics-based framework. It is shown that the “atomization energy” imparted by the high pressure injection of nitrogen gas into the field mixed foamed cement slurry is – by a significant margin – the highest energy process, and has a major impact on the void system in the cement slurry. There is no analog for this high energy exchange in current laboratory cement preparation and testing protocols. Quantifying the energy exchanges across the laboratory and field processes provides a basis for understanding relative impacts of these variables on cement structure, and can ultimately lead to the development of practices to improve cement testing and performance.

02 PETROLEUM↗

Improved damage tolerance of SiC-based nuclear fuel cladding with novel multi-layered SiC coating design at 1200 °C

Continuous SiC fibre reinforced SiC matrix composites (SiC f -SiC m ) with monolithic SiC outer coatings are considered as a damage-tolerant cladding design for loss of coolant accident (LOCA) conditions in light water reactors. However, monolithic SiC coatings are brittle and prone to catastrophic failure. In this study, a SiC f -SiC m cladding with a novel multi-layer SiC outer coating (11 sub-layers, ∼260 µm in total thickness) was investigated under C-ring compression at room temperature and 1200 °C in argon environment. Real-time synchrotron X-ray computed tomography (XCT) was employed to capture crack initiation and propagation processes. Compared to conventional monolithic SiC outer coatings, the multi-layer coating structure facilitated crack deflection and bifurcation enhancing its damage tolerance at both temperatures. Despite pre-existing surface cracks, claddings exhibited stable mechanical-performance at both temperatures. These initial cracks did not critically affect the failure processes as they were not aligned with the maximum stress direction. Furthermore, the microstructure, distribution of residual stresses, and local properties of individual components in the material were thoroughly characterized, and compared with open literature on conventional claddings with monolithic outer coatings. These results provide new insights into the failure mechanisms of multi-layer SiC coatings and offer guidance for the future design of accident-tolerant nuclear fuel claddings.

36 - MATERIALS SCIENCE↗

Unconventional Molecular Weight Dependence of Charge Transport in the High Mobility n‐type Semiconducting Polymer P(NDI2OD‐T2)

The charge transport and microstructural properties of five different molecular weight (MW) batches of the naphthalenediimide‐thiophene copolymer P(NDI2OD‐T2) are investigated. In particular, the field‐effect transistor (FET) performance and thin‐film microstructure of samples with MW varying from M n = 10 to 41 kDa are studied. Unlike conventional semiconducting polymers such as poly(3‐hexylthiophene) where FET mobility dramatically drops with decreasing molecular weight, the FET mobility of P(NDI2OD‐T2)‐based transistors processed from 1,2‐dichlorobenzene is found to increase with decreasing MW. Using a combination of grazing‐incidence wide‐angle X‐ray scattering, near‐edge X‐ray absorption fine‐structure spectroscopy, atomic force microscopy, and resonant soft X‐ray scattering, the increase in FET mobility with decreasing MW is attributed to the pronounced increase in the orientational correlation length (OCL) with decreasing MW. In particular, the OCL is observed to systematically increase from <100 nm for the highest MW samples to ≈1 µm for the lowest MW samples. The improvement in OCL and hence mobility for low MW samples is attributed to the lack of aggregation of low MW chains in solution promoting backbone ordering, with the pre‐aggregation of chains in 1,2‐dichlorobenzene found to suppress longer‐range liquid crystalline order.

Nahid, Masrur M.↗

Design of a V–Ti–Ni alloy with superelastic nano-precipitates

Stress-induced martensitic transformations enable metastable alloys to exhibit enhanced strain hardening capacity, leading to improved formability and toughness. As is well-known from transformation-induced plasticity (TRIP) steels, however, the resulting martensite can limit ductility and fatigue life due to its intrinsic brittleness. In this work, we explore an alloy design strategy that utilizes stress-induced martensitic transformations but does not retain the martensite phase. This strategy is based on the introduction of superelastic nano-precipitates, which exhibit reverse transformation after initial stress-induced forward transformation. To this end, utilizing ab-initio simulations and thermodynamic calculations we designed and produced a V 45 Ti 30 Ni 25 (at%) alloy. In this alloy, TiNi is present as nano-precipitates uniformly distributed within a ductile V-rich base-centered cubic (bcc) β matrix, as well as being present as a larger matrix phase. We characterized the microstructure of the produced alloy using various scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Furthermore, the bulk mechanical properties of the alloy are demonstrated through tensile tests, and the reversible transformation in each of the TiNi morphologies were confirmed by in-situ TEM micro-pillar compression experiments, in-situ high-energy diffraction synchrotron cyclic tensile tests, indentation experiments, and differential scanning calorimetry experiments. The observed transformation pathways and variables impacting phase stability are critically discussed.

59 BASIC BIOLOGICAL SCIENCES↗

Elements distribution and deformation features of a 4.5% Re nickel-based single crystal superalloy during creep at high temperature

Highlights: • Atom probe is used to investigate the element concentration changes in γ and γ' phase during creep. • Mo, W and Re diffuse from γ' to γ phase and enrich in γ/γ' interface during high temperature creep. • Super-dislocations in γ' phase may cross-slip from {111} to {100} plane due to the elements diffusions. • Dislocations shearing into γ' phase may decompose into K-W locks plus APB due to the refractory elements enrichment. - Abstract: By means of creep property measurement, microstructure observation and atom probe tomography, the elements distribution and deformation features of a 4.5% Re nickel-based single crystal superalloy during creep are investigated. Results show that after fully heat treated, the elements Al and Ta are mainly distributed in γ′ phase of alloy. After the alloy is crept up to fracture at 1100 °C/137 MPa, the change of the elements distributing in γ and γ′ phases occurs, wherein, the concentration decrement of the elements Al and Cr in γ′ and γ phases is attributed to their oxidation which may consume the ones. Moreover, some of the atoms Re, W and Mo dissolving in γ′ phase are repelled into γ matrix to reduce its internal energy. And the peak concentration of the atoms Re and W appears in the γ phase near the transition region, the atoms Re, W in the peak region cause the lattice distortion to increase the resistance of dislocations motion, which may improve the creep resistance of alloy. In the later stage of creep, dislocations shearing into the rafted γ′ phase may cross-slip from {111} to {100} plane to form the configuration of K-W locks, which may restrain the slipping of dislocations to improve the creep resistance of alloy. Wherein, the atom Re with lower diffusion coefficient may delay the dislocations in K-W locks for slipping and cross-slipping, which is thought to be the main reason of the K-W locks keeping in 4.5%Re alloy during creep at 1100 °C.

36 MATERIALS SCIENCE↗

High-Energy All-Solid-State Organic–Lithium Batteries Based on Ceramic Electrolytes

Recent studies have identified unique properties of organic battery electrode materials such as moderate redox potentials and mechanical softness which are uniquely beneficial for all-solid-state batteries based on ceramic electrolytes. Here, we further explore the promise of organic materials and demonstrate a sulfide electrolyte- based organic-lithium battery with a specific energy of 828 Wh kg –1 , rivaling the state-of- the-art of all-solid-state batteries. Two innovation steps are responsible for the accomplishment. First, the combination of lithium anode and the high-capacity cathode material pyrene-4,5,9,10-tetraone ensures a high theoretical specific energy. Second, the microstructure of the organic cathode is optimized with the introduction of cryomilling, a technique common to processing soft materials but not familiar to electrode fabrication. The cathode material utilization increases to 99.5% as a result, up from the 55–89% previously reported for ceramic electrolyte-based solid-state organic batteries. In conclusion, the improvement highlights the special requirements of solid-state organic electrodes for microstructural engineering while preserving the chemical integrity of components.

25 ENERGY STORAGE↗

Effects of Cooling Rate on 6.5% Silicon Steel Ordering

Increasing Si content improves magnetic and electrical properties of electrical steel, with 6.5% Si as the optimum. Unfortunately, when Si content approaches 5.7%, the Fe-Si alloy becomes brittle. At 6.5%, the steel is so brittle that a conventional cold rolling process is no longer applicable. The heterogeneous formation of B2 and D03 ordered phases is responsible for the severe material embrittlement. Studies show that the formation of these ordered phases can be impeded by rapid cooling. However, due to the availability of quenching media, only the cooling rates of water and brine water were investigated. At Ames Laboratory, a comprehensive study of the effect of rapid cooling rate on the formation of the ordered phases was carried out. Melt spin method was used to prepare thick steel ribbon. A wide range of cooling rates was achieved by varying wheel speed and melt-injection rate. A calibrated high-resolution thermal camera was used to measure temperature changes during solidification. The microstructures of the obtained ribbons were characterized using X-ray diffraction and TEM. The electrical, magnetic and mechanical properties were characterized using 4-pt probe, VSM, and macro-indentation methods. The relations between these physical properties and ordered phases were established.

36 MATERIALS SCIENCE↗

Cast-in-place, ambiently-dried, silica-based, high-temperature insulation

A novel sol-gel chemistry approach was developed to enable the simple integration of a cast-in-place, ambiently-dried insulation into high temperature applications. The insulation was silica based, synthesized using methyltrimethoxysilane (MTMS) as the precursor. MTMS created a unique silica microstructure that was mechanically robust, macroporous, and superhydrophobic. To allow for casting into and around small, orthogonal features, zirconia fibers were added to increase stiffness and minimize contraction that could otherwise cause cracking during drying. Radiative heat transport was reduced by adding titania powder as an opacifier. To assess relevance to high temperature thermoelectric generator technology, a comprehensive set of materials characterizations were conducted. The silica gel was thermally stable, retained superhydrophobicity with a water contact angle > 150° , and showed a high electrical resistance > 1 GΩ, regardless of heating temperature (up to 600 °C in Ar for 4 h). In addition, it exhibited a Young's modulus ~3.7 MPa in room temperature and a low thermal conductivity < 0.08 W/m.K before and after heat treatment. Thus, based on the simplicity of the manufacturing process and optimized material properties, we believe this technology can act as an effective cast-in-place thermal insulation (CTI) for thermoelectric generators and myriad other applications requiring improved thermal efficiency.

36 MATERIALS SCIENCE↗

Rapid solidification of high-conductivity copper alloys

The main objective was to develop improved copper alloys of high strength and high thermal and electric conductivity. Chill block melt spinning was used to produce binary alloys of Cu-Cr and Cu-Zr, and ternary alloys of Cu-Cr-Ag. By quenching from the liquid state, up to 5 atomic percent of Cr and Zr were retained in metastable extended solid solution during the rapid solidification process. Eutectic solidification was avoided and the full strengthening benefits of the large volume fraction of precipitates were realized by subsequent aging treatment. The very low solid solubility of Cr and Zr in Cu result in a high conductivity Cu matrix strengthened by second phase precipitates. Tensile properties on as-cast and aged ribbons were measured at room and elevated temperatures. Precipitate coarsening of Cr in Cu was studied by changes in electrical resistance during aging. X-ray diffraction was used to measure the lattice parameter and the degree of supersaturation of the matrix. The microstructures were characterized by optical and electron microscopy.

Bloom, Theodore Atlas↗

Regulating the properties of activated carbon for supercapacitors: impact of particle size and degree of aromatization of hydrochar

Hydrochar (HC), obtained by the hydrothermal carbonization (HTC) of biomass, is an excellent precursor for preparing activated carbon (AC). However, the effects of the intrinsic properties of HC on the microstructure and electrochemical properties of AC are largely unknown. Here, this study investigates the impact of particle size and the degree of aromatization of in-situ HC on the microstructure and electrochemical properties of AC. Our results show that a large particle size and a high degree of aromatization help protect the HC from overactivation by ZnCl 2 , resulting in an large specific surface area (SSA > 2000 m 2 /g) and high mesopore to micropore volume ratio value ( V mes /V mic > 0.3) of the AC. Electrochemical performance measurements show a maximum specific capacitance of 218 F/g at 0.5 A/g was achieved in all samples where the AC (AC180-10 h) was prepared by activating HC180-10 h with a large size, a high degree of aromatization, and abundant surface oxygen-containing functional groups. After AC180-10 h was assembled into a supercapacitor, the specific capacitance of AC180-10 h still reached 158 F/g at 0.5 A/g, and it showed excellent cycling stability. This study advances the understanding of the impact of HC particle size and degree of aromatization on AC properties, providing new insights into tailoring HC qualities so that improving improve the properties of AC.

36 MATERIALS SCIENCE↗

Modern nanostructured ferritic alloys: A compelling and viable choice for sodium fast reactor fuel cladding applications

Sodium fast reactor cores present a truly challenging environment for the fuel cladding and core structural materials that limit achievable fuel burnup in these systems. Modern nanostructured ferritic alloys have the potential to deliver the desired high performance characteristics where historic austenitic and ferritic/martensitic alloys fall short. Herein, a new nanostructured ferritic alloy, OFRAC ( O ak Ridge F ast R eactor A dvanced Fuel C ladding), is developed and demonstrated in cladding geometry with a length > 1 m. The alloy composition and microstructure are tailored to deliver dramatically improved strength and creep resistance. At 600 °C the ultimate tensile strength is ~600 MPa and the stress to induce a steady state strain rate of 10 -6 s -1 is 500 MPa vs. 200 MPa for traditional ferritic/martensitic alloys. A very high defect sink density was engineered in these alloys that is expected to further enhance the traditional good swelling and irradiation creep resistance of ferritic/martensitic steels. These significant improvements along with the demonstrated viability for seamless cladding production indicate that this alloy is a compelling and viable choice for sodium fast reactor fuel cladding applications.

36 MATERIALS SCIENCE↗

Multiscale Characterization of Additive Manufacturing Components with Computed Tomography, 3D X-ray Microscopy, and Deep Learning

Additive manufacturing (AM) facilitates the creation of complex-geometry parts, driving advancements in lightweight aerospace components, high-efficiency engine cooling channels, and customized medical implants. However, ensuring the quality and reliability of AM parts remains challenging due to internal defects, surface irregularities, porosity, and residual trapped powder, which are often inaccessible to traditional inspection methods. Recent developments in X-ray computed tomography (XCT) and 3D X-ray microscopy (XRM), particularly systems equipped with resolution-at-a-distance (RaaD™) capabilities, enable high-resolution, non-destructive evaluation of AM components across multiple scales, from sub-micrometer to macroscopic levels. This paper explores modern XCT and XRM techniques for multiscale characterization of AM parts, focusing on their ability to detect and analyze defects such as porosity, cracks, inclusions, and surface roughness, while offering insights into defect formation mechanisms, material properties, and process-induced variations. The integration of deep learning (DL) frameworks, including Simurgh, DeepRecon, and DeepScout, enhances XCT/XRM workflows by reducing scan times, improving resolution recovery, and enabling accurate defect detection even with limited projection data. These DL-based methods overcome limitations of traditional reconstruction techniques, enabling faster, more reliable characterization of dense materials like Inconel 718 and novel alloys such as AlCe. Applications include process parameter optimization, high-throughput quality control, and multistage AM process evaluation, with DL-enhanced workflows accelerating analysis times from weeks to days. Correlative imaging approaches further validate XCT and XRM data against scanning electron microscopy (SEM) images of physically sectioned samples, confirming the accuracy of DL-based reconstructions and enabling comprehensive defect analysis. While challenges remain in generalizing DL models to diverse materials and imaging conditions, improvements in resolution, noise reduction, and defect detection highlight the transformative potential of these methods. This multiscale and correlative approach enables precise identification and correlation of microstructural features with the overall performance of AM components. By integrating advanced XCT, XRM, and DL techniques, this paper demonstrates a significant leap forward in AM characterization, offering valuable insights into the relationships between processing parameters, microstructure, and part performance, and driving innovations that enhance the quality and reliability of AM products for demanding industrial applications.

Additive manufacturing↗

Strengthening of Cu–Ni–Si alloy using high-pressure torsion and aging

An age-hardenable Cu–2.9%Ni–0.6%Si alloy was subjected to high-pressure torsion. Aging behavior was investigated in terms of hardness, electrical conductivity and microstructural features. Transmission electron microscopy showed that the grain size is refined to ∼ 150 nm and the Vickers microhardness was significantly increased through the HPT processing. Aging treatment of the HPT-processed alloy led to a further increase in the hardness. Electrical conductivity is also improved with the aging treatment. It was confirmed that the simultaneous strengthening by grain refinement and fine precipitation is achieved while maintaining high electrical conductivity. Three dimensional atom probe analysis including high-resolution transmission electron microscopy revealed that nanosized precipitates having compositions of a metastable Cu{sub 3}Ni{sub 5}Si{sub 2} phase and a stable NiSi phase were formed in the Cu matrix by aging of the HPT-processed samples and these particles are responsible for the additional increase in strength after the HPT processing. - Highlights: • Grain refinement is achieved in Corson alloy the size of ∼150nm by HPT. • Aging at 300°C after HPT leads to further increase in the mechanical property. • Electrical conductivity reaches 40% IACS after aging for 100 h. • 3D-APT revealed the formation of nanosized-precipitates during aging treatment. • Simultaneous hardening in both grain refinement and precipitation is achieved.

36 MATERIALS SCIENCE↗

Engineering the Thermoelectric Transport in Half-Heusler Materials through a Bottom-Up Nanostructure Synthesis

Half-Heusler (HH) alloys are among the best promising thermoelectric (TE) materials applicable for the middle-to-high temperature power generation. Despite of the large thermoelectric power factor and decent figure-of-merit ZT (≈1), their broad applications and enhancement on TE performance are limited by the high intrinsic lattice thermal conductivity (κ L ) due to insufficiencies of phonon scattering mechanisms, and the fewer powerful strategies associated with the microstructural engineering for HH materials. This study reports a bottom-up nanostructure synthesis approach for these HH materials based on the displacement reaction between metal chlorides/bromides and magnesium (or lithium), followed by vacuum-assisted spark plasma sintering process. The samples are featured with dense dislocation arrays at the grain boundaries, leading to a minimum κ L of ≈1 W m -1 K -1 at 900 K and one of the highest ZT (≈1) and predicted η (≈11%) for n-type Hf 0.25 Zr 0.75 NiSn 0.97 Sb 0.03 . Further manipulation on the dislocation defects at the grain boundaries of p-type Nb 0.8 Ti 0.2 FeSb leads to enhanced maximum power factor of 47 × 10 -4 W m -1 K -2 and the predicted η of ≈7.5%. Moreover, vanadium substitution in FeNb 0.56 V 0.24 Ti 0.2 Sb significantly promotes the η to ≈11%. This strategy can be extended to a broad range of advanced alloys and compounds for improved properties.

36 MATERIALS SCIENCE↗

Development and Processing of Nickel Aluminide-Carbide Alloys

With the upper temperature limit of the Ni-based superalloys attained, a new class of materials is required. Intermetallics appear as likely candidates because of their attractive physical properties. With a relatively low density, high thermal conductivity, excellent oxidation resistance, high melting point, and simple crystal structure, nickel aluminide (NiAl) appears to be a potential candidate. However, NiAl is limited in structural applications due to its low room temperature fracture toughness and poor elevated temperature strength. One approach to improving these properties has been through the application of eutectic composites. Researchers have shown that containerless directional solidification of NiAl-based eutectic alloys can provide improvement in both the creep strength and fracture toughness. Although these systems have shown improvements in the mechanical properties, the presence of refractory metals increases the density significantly in some alloys. Lower density systems, such as the carbides, nitrides, and borides, may provide NiAl-based eutectic structure. With little or no information available on these systems, experimental investigation is required. The objective of this research was to locate and develop NiAl-carbide eutectic alloys. Exploratory arc-melts were performed in NiAl-refractory metal-C systems. Refractory metal systems investigated included Co, Cr, Fe, Hf, Mo, Nb, Ta, Ti, W, and Zr. Systems containing carbides with excellent stability (i.e.,HfC, NbC, TaC, TiC, and ZrC) produced large blocky cubic carbides in an NiAl matrix. The carbides appeared to have formed in the liquid state and were randomly distributed throughout the polycrystalline NiAl. The Co, Cr, Fe, Mo, and W systems contained NiAl dendrites with a two-phase interdendritic microconstituent present. Of these systems, the NiAl-Mo-C system had the most promising microstructure for in-situ composites. Three processing techniques were used to evaluate the NiAl-Mo-C system: arc-melting, slow cooling, and containerless directional solidification. Arc-melting provided a wide range of compositions in an economical and simple fashion. The slow cooled ingots provided larger ingots and slower cooling rates than arc-melting. Directional solidification was used to produce in-situ composites consisting of NiAl reinforced with molybdenum carbides.

Newport, Timothy Scott↗

Thermophysical and Thermomechanical Properties of Thermal Barrier Coating Systems

Thermal barrier coatings have been developed for advanced gas turbine and diesel engine applications to improve engine reliability and fuel efficiency. However, the issue of coating durability under high temperature cyclic conditions is still of major concern. The coating failure is closely related to thermal stresses and oxidation in the coating systems. Coating shrinkage cracking resulting from ceramic sintering and creep at high temperatures can further accelerate the coating failure process. The purpose of this paper is to address critical issues such as ceramic sintering and creep, thermal fatigue and their relevance to coating life prediction. Novel test approaches have been established to obtain critical thermophysical and thermomechanical properties of the coating systems under near-realistic temperature and stress gradients encountered in advanced engine systems. Emphasis is placed on the dynamic changes of the coating thermal conductivity and elastic modulus, fatigue and creep interactions, and resulting failure mechanisms during the simulated engine tests. Detailed experimental and modeling results describing processes occurring in the thermal barrier coating systems provide a framework for developing strategies to manage ceramic coating architecture, microstructure and properties.

Zhu, Dongming↗