Modeling Internal Material Melting
The purpose of the SEED LDRD was to create new functionality to model internal material melting and solidification inside the state-of-the-art nuclear fuel performance simulation code BISON.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The purpose of the SEED LDRD was to create new functionality to model internal material melting and solidification inside the state-of-the-art nuclear fuel performance simulation code BISON.
The Powder River Basin (PRB) Carbon Ore, Rare Earth, and Critical Minerals (CORE-CM) project is part of the Department of Energy sponsored CORE-CM initiative focused on domestic production of critical minerals and promoting economic development in traditionally fossil fuel producing basins. An important part of this project is regional assessment of waste streams and development of basinal strategies for waste stream reuse within the critical minerals (CM) supply chain. The availability of water for all parts of the CM supply chain is of particular concern in the arid mountain west. In the Wyoming PRB, average annual production of produced water (PW) by the oil and gas industry is more than 16 billion gallons (2015-2022). Through published data and engagement with industry partners, we conducted a preliminary investigation of PW in the PRB to understand volumes, quality, and the potential for use in the CM supply chain. PW was assessed for potential as a direct feedstock and for use in CM processing of a variety of conventional and unconventional feedstocks, including ore from the Bear Lodge Alkaline Complex, coal, and coal byproducts. Preliminary findings suggest that PRB PW contains significantly lower concentrations of rare earth elements (REE) and lithium than would be considered economic at this time. For example, concentrations of REE+Sc measured in PRB PW are <1 ppb (DE-EE0007603), and only seven PRB PW samples reported in the USGS PW database had lithium concentrations ≥50 ppm. However, enrichment of CM in residual brine and sludge from PW evaporation and solidification treatment ponds may yield concentrations of interest over a pond lifetime and should be considered in future studies. Coal bed methane (CBM) PW accounted for 42% of all PW in the Wyoming PRB in 2022. Compared to non-CBM PW, PRB CBM water quality generally meets standards allowing surface discharge and reuse in local industries such as livestock. CBM PW may help to fill water needs within the CM supply chain. Understanding the distribution of CBM PW that is discharged versus reused will help develop basinal reuse strategies.
During NPP operation, several waste streams are generated, caused by different technical and physical processes. Besides others, liquid waste represents one of the major types of waste. Depending on national regulation for storage and disposal of radioactive waste, solidification can be one specific requirement. To accommodate the global request for waste treatment systems Westinghouse developed several specific treatment processes for the different types of waste. In the period of 2006 to 2008 Westinghouse awarded several contracts for the design and delivery of waste treatment systems related to the latest CPR-1000 nuclear power plants. One of these contracts contains the delivery of four Cementation Facilities for waste treatment, s.c. 'Follow on Cementations' dedicated to three locations, HongYanHe, NingDe and YangJiang, of new CPR-1000 nuclear power stations in the People's Republic of China. Previously, Westinghouse delivered a similar cementation facility to the CPR-1000 plant LingAo II, in Daya Bay, PR China. This plant already passed the hot functioning tests successfully in June 2012 and is now ready and released for regular operation. The 'Follow on plants' are designed to package three 'typical' kind of radioactive waste: evaporator concentrates, spent resins and filter cartridges. The purpose of this paper is to provide an overview on the Westinghouse experience to design and execution of cementation facilities. (authors)
Improved cementation of low and intermediate level radioactive waste (ILW and LLW) aided by vortex electromagnetic treatment as well as silica addition was investigated. Positive effects including accelerated curing of boron-containing cement waste forms, improve end product quality, decreased product volume and reduced secondary LRW volume from equipment decontamination were established. These results established the possibility of boron-containing LRW cementation without the use of neutralizing alkaline additives that greatly increase the volume of the final product intended for long-term storage (burial). Physical (electromagnetic) treatment in a vortex mixer can change the state of LRW versus chemical treatment. By treating the liquid phase of cement solution only, instead of the whole solution, and using fine powder and nano-particles of ferric oxides instead of separable ferromagnetic cores for the activating agents the positive effect are obtained. VET for 1 to 3 minutes yields boron-containing LRW cemented products of satisfactory quality. Silica addition at 10 % by weight will accelerate curing and solidification and to decrease radionuclide leaching rates from boron-containing cement products. (authors)
A water treatment system at a United States Environmental Protection Agency (USEPA) Superfund site impacted by radiological contaminants is used to treat water entering the site. The United States Army Corps of Engineers (USACE) is actively managing the remedial action for the USEPA using contracts to support the multiple activities on site. The site is where former gas mantle production facilities operated around the turn of the century. The manufacturing facilities used thorium ores to develop the mantles and disposed of off-specification mantles and ore residuals in the surrounding areas. During Site remedial actions, both groundwater and surface water comes into contact with contaminated soils and must be collected and treated at an on-site treatment facility. The radionuclides thorium and radium with associated progeny are the main concern for treatment. Suspended solids, volatile organic compounds, and select metals are also monitored during water treatment. The water treatment process begins were water is pumped to a collection tank where debris and grit settle out. Stored water is pumped to a coagulant tank containing poly-aluminum chloride to collect dissolved solids. The water passes into a reaction tube where aspirated air is added or reagent added to remove Volatile Organic Compounds (VOC'S) by mass transfer and convert dissolved iron to a solid. The water enters the flocculent polymer tank to drop solids out. The flocculated water overflows to a fluidized bed contact chamber to increase precipitation. Flocculation is where colloids of material drop out of suspension and settle. The settled solids are periodically removed and disposed of as radioactive waste. The water is passed through filters and an ion exchange process to extract the radionuclides. Several million liters of water are processed each year from two water treatment plants servicing different areas of the remediation site. Ion exchange resin and filter material are periodically replaced and disposed of as radioactive waste. A total of 0.85 m{sup 3} of waste sludge per year requires disposal on average, in addition to another 6.6 m{sup 3} of waste cartridge filters. All water discharges are regulated by a state of New Jersey Pollutant Discharge Elimination System Permit implemented by the Federal Water Pollution Control Act (Clean Water Act). Laboratory analyses are required to satisfy requirements of the state NPDES permit. Specific monitoring parameters and discharge rates will be provided. Use of the water treatment systems drastically reduces the amount of contaminated water requiring solidification and water disposal to near zero. Millions of liters of potentially contaminated water from excavation activities is treated and released within permit limits. A small volume of solid radioactive waste (21 cubic meters) is generated annually from water treatment process operations. Management of ground and surface water is effectively controlled in remediation areas by the use of sumps, erosion control measures and pumping of water to storage vessels. Continued excavations can be made as water impacting the site is effectively controlled. (authors)
This paper presented in-situ chemical precipitation for radioactive liquid waste by using chemical agents. Results are reported on large-scale implementation on the removal of {sup 137}Cs, {sup 134}Cs and {sup 60}Co from liquid radioactive waste generating from Nuclear Research and Training Centre. Total amount of liquid radioactive waste was 35 m{sup 3} and main radionuclides were Cs-137, Cs- 134 and Co-60. Initial radioactivity concentration of the liquid waste was 2264, 17 and 9 Bq/liter for Cs-137, Cs-134 and Co-60 respectively. Potassium ferro cyanide was selected as chemical agent at high pH levels 8-10 according to laboratory tests. After the process, radioactive sludge precipitated at the bottom of the tank and decontaminated clean liquid was evaluated depending on discharge limits. By this precipitation method decontamination factors were determined as 60, 9 and 17 for Cs-137, Cs-134 and Co-60 respectively. At the bottom of the tank radioactive sludge amount was 0.98 m{sup 3}. It was transferred by sludge pumps to cementation unit for solidification. By in situ chemical processing 97% of volume reduction was achieved. Using the optimal concentration of 0.75 M potassium ferro cyanide about 98% of the {sup 137}Cs can be removed at pH 8. The Potassium ferro cyanide precipitation method could be used successfully in large scale applications with nickel and ferrum agents for removal of Cs-137, Cs-134 and Co- 60. Although DF values of laboratory test were much higher than in-situ implementation, liquid radioactive waste was decontaminated successfully by using potassium ferro cyanide. Majority of liquid waste were discharged as clean liquid. %97.2 volumetric amount of liquid waste was cleaned and discharged at the original site. Reduced amount of sludge transportation in drums is more economical and safer method than liquid transportation. Although DF values could be different for each of applications related to main specifications of original liquid waste, this study shows that in-situ treatment of liquid waste by using potassium ferro cyanide is not only a cost effective method but also reduce radiological risks as well. (authors)
Savannah River Remediation (SRR) was contracted by the U.S. Department of Energy (DOE) to manage its liquid waste project at the Savannah River Site. The liquid waste project is a unique, high hazard nuclear waste treatment and disposal facility consisting of 51 one million-gallon underground waste tanks, a solvent extraction processing unit, a vitrification facility for the highest radioactive waste, and a grout solidification and disposal facility for lower radioactive decontaminated salt solution. Our Project mission is to treat the nuclear waste and close the associated storage and treatment facilities, of which, 8 tanks have been closed to date. The Lean philosophy took root decades ago in the manufacturing sector and started with the work of W. Edwards Deming and his contemporaries. In more recent years the process has matured in the Toyota Production System and migrated into fields as diverse as services industries, health-care, and now the DOE complex. At SRR, a Lean business management system was adopted to address site inefficiencies, aging infrastructure concerns and budget constraints. With yearly escalation and flat budgets, continuous improvement is taking on a larger role - improving the work accomplished for each dollar. This paper focuses on the program results achieved to date, including the lifecycle savings identified through the Rapid Improvement Event (RIE) process. The RIE process is a Lean tool which creates a cross-functional team to analyze, develop and implement improvements for a given process. DOE-EM has recently emphasized the value of contractor's continuous improvement programs through their implementation of Plan of Action and Milestone (POAM): Goal 2 (Increase Efficiency/Improve Performance) Reduce EM Operations Cost in FY16. POAM Goal 2 was a FY 16 effort to achieve 5% cost savings across most programs. This past year's cost savings initiatives will likely become a trend as DOE and its contractors look to do more with less. In support of our own business objectives, as well as, DOE's motivation to improve efficiencies, SRR has held over one hundred formal Lean events and dozens of 5S events that have driven improvement across the Project, including tank closure and production facilities. These improvements have significantly reduced the time required to process material and achieve the overall goal of hazard reduction and tank closure. (authors)
The Savannah River Site (SRS) Liquid Waste System (LWS) safely stores and treats high-level radioactive waste. The LWS consists of 51 waste storage tanks (eight of which are operationally closed and filled with grout), waste evaporators, treatment facilities, and solidification facilities such as the Defense Waste Processing Facility (DWPF) and Salt-stone Production Facility (SPF). At Savannah River Remediation (SRR), the liquid waste contractor, robotic technologies are needed to enter areas and spaces that are otherwise inaccessible or prohibit direct access by workers due to unsafe, unstable, or unknown physical or structural conditions; or configurations that are hard to reach or beyond reach without taking extraordinary mechanical measures. As discussed below, SRR uses robotic technologies at various LWS facilities to reduce dose to the workers as well as provide access to unreachable locations due to the presence of radiological or chemical hazards. (author)
Rod-type fuel slugs and spherical powder of U- 10wt.%Zr alloy was also fabricated and characterized in microstructure by injection casting, gravity casting and centrifugal atomization process. U grains became finer from ∼30μm in conventionally ingot rod to ∼2μm in atomized powder. Laminar structure became so fine from ∼0.2μm in conventionally cast ingot rod to 0.05∼0.1μm in atomized powder. Metallic fuels such as U-Zr and U-Pu-Zr alloys have been considered as a nuclear fuel for a sodium-cooled fast reactor (SFR), related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980's. Metallic fuel slugs of U-Pu-Zr alloys for SFR have conventionally been fabricated by an injection casting method. U-Pu-Zr alloy melts are injected and cast into quartz tube molds during injection casting. Metallic fuel slugs are collected by fracturing quartz tubes from the molds. Demolded quartz tubes are treated with radioactive wastes. Recently, management of minor actinides (MA) became an important issue because direct disposal of the long-lived MA can be a long-term burden for a tentative repository up to several hundreds of thousand years. The metallic fuel for SFR should be remotely fabricated under a radiation shielded environment such as a hot cell, because it contains highly radioactive MA such as Np, Am and Cm. The addition of MA in the fuel composition introduces new challenges in the manufacturing of a metallic fuel slug. Am has a high vapor pressure under a vacuum atmosphere at above a melting temperature of U-Zr or U-Pu-Zr. Used graphite crucibles and quartz molds cannot be recycled easily because of difficult decontamination of radioactive residues on their surfaces. It is necessary to minimize the vaporization of Am and volume of radioactive wastes. Atomized metallic fuel does not need these quartz molds during fabrication, as uranium alloys are prepared as a particle form. It is possible to reduce the formation of radioactive wastes by applying the fabrication process of a particulate metallic fuel. Metallic fuel having a fine microstructure, which originates from a rapid solidification effect during atomization process, results in a higher FG release rate during irradiation. In the case of applying a new forming method such as vibrocompaction in Zr sheath, the sheath can act as a reliable FCCI (fuel/cladding chemical interaction) barrier and a re-constraint for external elongation. In addition, atomized fuel powder, dispersed in a Na liquid metal having a high thermal conductivity, may have a lower temperature distribution during irradiation. In order to develop an efficient fabrication process of metallic fuel for SFR, U-Zr ingot rods were fabricated in a lab-scale with various casting methods. Rod-type U-Zr fuel slugs were fabricated by gravity casting and injection casting. Spherical powder of U-Zr alloy was also fabricated by centrifugal atomization. And then, the microstructural characteristics were investigated by using electron microscopes and energy-dispersive electron X-ray spectroscopy. Atomized U-10Zr powder generally showed spherical morphology of below 200 μm in particle size. U grains became finer from ∼30 μm in conventionally ingot rod to ∼2 μm in atomized powder. Laminar structure became so fine from ∼0.2 μm in conventionally cast ingot rod to 0.05∼0.1 μm in atomized powder. Atomized particulate metallic fuel for SFR has a fine microstructure, resulting in a higher fission gas release rate during irradiation. (authors)
Recent global interest in pyroprocessing and molten salt reactors has brought salt sampling methods and techniques back to the forefront of nuclear safeguards concerns. Issues with uranium supplies have also encouraged various countries to pursue advanced nuclear fuel cycles. Tracking nuclear material in molten salt has proven to be a challenge and updating molten salt sampling will greatly help in this endeavor. Molten salt is problematic to sample due to salt stratification, lack of homogeneity, solids, and difficulty with hot cell adaptations. Various salt sampling techniques have been used since before the 1960s including surface, spoon/spatula, and bar solidification. Since then, new types of sampling techniques have been developed to improve sampling results. These include rod/dip, pipet, suction, filtered sampling along with devices such as the Valve Core Sampler and the Multi-Level Sampler. These different approaches are being analyzed and improved upon along with developing requirements for an improved salt sampling device. Work continues to develop salt samplers that are more robust, easier to segment, collect at a specific depth, can work with filters, and can collect fines. Sampling parameters are also being narrowed in terms of stirring, settling time, filtration, depth, etc. In the future, we hope to address deficiencies for process control and nuclear material accountancy control by determining the best way to collect samples that minimizes contaminants and is representative. A compilation of salt sampling approaches, analyses techniques, and an evaluation of findings will be presented.
As part of an initiative to steward research, development, and innovation into the nuclear fuel cycle, Idaho National Laboratory is building the Beartooth testbed. Beartooth will include a cascade of centrifugal contactors, glove box lines, solidification, and dissolution equipment to aid in the progression of novel separation techniques and provide hands-on opportunities to early-career separation scientists. Beartooth will incorporate novel monitoring techniques using sensors and machine learning algorithms to inform a process operator of separation conditions. This research is examining monitoring technologies not typically used in nuclear separation processes such as acoustic microphones, accelerometers, infrared cameras, red-green-blue color sensors, among others. These sensors are being examined for their functionality within a separation process and their ability to detect applicable signals. Machine learning methods are being developed to determine their utility in detecting faults and alerting operators of expected and unexpected events. These methods have the potential to impact Safeguards by Design efforts and real-time decision making. This overview will detail preliminary results from acoustic, vibration, and color sensors.
Latent heat thermal energy storage (LHTES) using phase change material (PCM) has attracted increased attention as a viable solution for overcoming the mismatch between energy supply and demand for renewable energy-based systems. PCM-embedded heat exchangers (PCM-HX) have the potential to significantly improve thermal performance due to high storage capacity and low temperature variation during the phase change process. Most models for simulating LHTES heat transfer use Computational Fluid Dynamics (CFD) simulations, which have high computational costs resulting from considering the complex and time-dependent physics relevant to PCM-HXs. In this paper, a Generalized Resistance Capacitance-based Model (GRCM) was developed to predict the thermal performance of arbitrary PCM-HXs in a computationally efficient manner without compromising modeling accuracy. The GRCM is exercised for three case studies: (i) verification for a single-slabbed finned PCM-HX, (ii) verification and validation for a copper foam/paraffin composite PCM-HX, and (iii) validation for a straight tube annular finned PCM-HX. The copper foam PCM-HX uses an electric heater at the top of HX, while the other two configurations utilize water as heat transfer fluid. For the single-slabbed finned PCM-HX melting case, the mean deviation in average PCM temperature predicted by the GRCM compared to the CFD model was between 0.56 – 0.73 K, with maximum temperature deviation of 2.68 K. For the HTF outlet temperature, the validation results showed that GRCM prediction matches very well with experimental data, with mean temperature deviation of 0.24 K during melting case, while for solidification case was 0.34 K. These results showcase the GRCM’s capability for accurately reproducing the thermal characteristics of PCM-HXs with considerably lower computational effort.
The load profile for domestic water heating is time-dependent and can result in high energy demand during peak operating times. Shifting this peak load can have significant environmental and economic impacts. Phase change material (PCM)-based thermal energy storage (TES) is a potentially useful technology for peak load shifting in domestic hot water (DHW) applications thanks to its high latent heat and energy density. In this study, an annular finned-tube PCM-HX design concept was optimized for a load-shifting TES unit to meet the Department of Energy standard for a medium-usage DHW heater using a resistance-capacitance model (RCM) integrated with a Multi-Objective Genetic Algorithm. The optimized design comprised 70 identical annular finned-tube PCM-HX units connected in parallel and utilizing RT62HC as the PCM. A single PCM-HX unit was prototyped and tested in a vertically oriented setup with upward heat transfer fluid (HTF) flow. The hot water supply time was defined based on a cutoff temperature of 51.7°C. The as-designed mass flow rate (1.5 g/s) was tested to assess the performance of the prototyped PCM-HX unit for RCM validation. For the experimental investigation, RTD sensor bundles measured HTF temperature at the PCM-HX inlet and outlet, and a Coriolis flow meter accurately measured the HTF mass flow rate. The simulated discharging power underpredicted the experimental result by about 12%, and the simulated hot water supply time underpredicted the experimental result by approximately 13% for the as-designed mass flow rate (1.5 g/s). The average deviation of the hot water supply temperature between the experimental and RCM results during the complete PCM solidification process was 1.3 K for the as-designed mass flow rate. The overall good agreement between the experimental and RCM results provides confidence that computationally efficient models such as RCM can be utilized for design optimization of PCM-HXs.
The effects of varying ingot diameters on the characteristics of round ESR ingots of 282 alloy are evaluated through a combined experimental and modeling study. Ingots of four different diameters --100 mm, 150 mm, 200 mm and 500 mm, were sectioned and analyzed using metallography to assess spatial variations in dendritic structure (primary / secondary dendrite arm spacings – PDAS/SDAS) across these ingots. Melt parameters of the processes were input into the simulation code, MeltFlow-ESR™ to theoretically predict PDAS/SDAS in the ingots. The values for PDAS/SDAS predicted by the simulations are compared with those measured by experiments and quantitative differences in these values are discussed in the context of the capability and limitations of the model and measurement methods. Both the predicted and measured values show that the PDAS/SDAS values increase with increasing ingot size. In addition, the relation with other ingot characteristics, such as local solidification time as well as the likelihood for freckle formation are discussed. The implication of these results for down-stream ingot processing and for ingot soundness are discussed.
Systems and methods of making a cast steel alloy crankshaft for an internal combustion engine are provided. The method comprises providing a mold of the crankshaft. The mold has cavities to form the crankshaft. The method further comprises melting a first metallic material at between 1400 degrees Celsius (° C.) and 1600° C. to define a molten metallic material. In addition, the method further comprises feeding the molten metallic material at a riser connection angle of between 30° and 75° in the cavities of the negative sand cast mold. The method further comprises cooling the molten metallic material at a solidification time of between 5 seconds (sec) and 20 sec in the negative sand cast mold with at least one chill member to define a solidified metallic material having dimensions of the cast steel alloy crankshaft. Furthermore, the method comprises separating the solidified metallic material from the negative sand cast mold to define the cast steel alloy crankshaft.
Laser powder bed fusion (LPBF) is a metal additive manufacturing method that produces non-traditional microstructures as a result of the rapid solidification and thermal cycling inherent to the process. When using LPBF-produced material in application, these unique microstructures challenge the applicability of well developed mechanical property databases achieved by conventional heat treatments. For wider adoption of this technology, a more holistic understanding is necessary on how process attributes develop material structure, which dictate mechanical properties. This dissertation explores the process– structure–property relationships in LPBF 17-4 PH steel through systematic evaluation of atmospheric processing and heat treatment effects on microstructure and mechanical performance. Specimens were fabricated under controlled build environments, subjected to a range of solutionizing, homogenizing, and aging treatments, and characterized using optical microscopy, electron back scatter diffraction (EBSD), and X-ray diffraction (XRD) to quantify phase evolution. Tensile testing was performed to directly link heat treatment pathway and nitrogen absorption to mechanical performance. This work demonstrates where conventional heat treatment standards are applicable to LPBF 17-4 PH steel and where modifications are required. By directly correlating phase stability, nitrogen effects, and tensile response, this work provides practical guidelines for tailoring post-processing strategies. These findings underscore that successful application of LPBF 17-4 PH steel requires explicit consideration of both build environment and post-processing. By linking processing conditions to microstructure and performance, this work advances understanding of critical variables that govern reliability of additively manufactured precipitation-hardened stainless steels in demanding applications.
UZrCN has exhibited thermophysical properties beneficial to high temperature reactor applications such as nuclear thermal rockets. The present work investigates a novel liquid phase synthesis method involving the admission of nitrogen gas during arc melting of uranium, zirconium, and carbon. Initial microstructural examinations using SEM indicated that the samples remain heterogenous with zirconium-rich cores in a uranium-rich matrix. Heterogeneity resulted from large differences in melting temperature of the major constituents and rapid solidification. Additional EDS, combustion analysis, and inert gas fusion analysis proved that the core regions have both uranium and zirconium and establish that carbon and nitrogen are retained during the fabrication process. XRD clarifies that the light elements did not form compounds with the uranium matrix but rather incorporated into the core region forming a sub-stoichiometric UZrCN. Heat treatment performed on equimolar U-Zr-C resulted in an increase in the homogenous phase present with an XRD pattern reflecting a ternary UZrCN despite small amounts of segregation in the final button.
Idaho National Laboratory’s (INL) nuclear fuel cycle capabilities enable the deployment of technologies that sustain the current reactor fleet, support demonstration and deployment of new advanced reactors, and facilitate management and disposition of existing and future radiological waste materials. INL focuses on deploying nuclear energy systems with confidence by decreasing proliferation risk through research that demonstrates process transparency and supports safeguards and security by design. An example of these capabilities is the Beartooth test bed, set to begin operations toward the end of fiscal year 2026. Beartooth will include a cascade of centrifugal contactors, glove box lines, and solidification and dissolution equipment to aid in the progression of novel separation techniques and to provide hands-on experience to cultivate and maintain a robust workforce of experts. To support Beartooth’s enhanced instrumentation and monitoring equipment needs, several nontraditional sensors are being considered for future deployment. The non-traditional sensors include accelerometers, acoustic microphones, and infrared cameras. These nontraditional sensors have the potential to not only help monitor the process but also enhance nuclear safeguards.