Search NASA⌕ Search

SEARCH · Search NASA

Results for “static models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

A potential flight evaluation of an upper-surface-blowing/circulation-control-wing concept

The technology data base for powered lift aircraft design has advanced over the last 15 years. NASA's Quiet Short Haul Research Aircraft (QSRA) has provided a flight verification of upper surface blowing (USB) technology. The A-6 Circulation Control Wing flight demonstration aricraft has provide data for circulation control wing (CCW) technology. Recent small scale wind tunnel model tests and full scale static flow turning test have shown the potential of combining USB with CCW technology. A flight research program is deemed necessary to fully explore the performance and control aspects of CCW jet substitution for the mechanical USB Coanda flap. The required hardware design would also address questions about the development of flight weight ducts and CCW jets and the engine bleed-air capabilities vs requirements. NASA's QSRA would be an optimum flight research vehicle for modification to the USB/CCW configuration. The existing QSRA data base, the design simplicity of the QSRA wing trailing edge controls, availability of engine bleed-air, and the low risk, low cost potential of the suggested program is discussed.

Riddle, Dennis W.↗

Visualization techniques for studying high angle of attack separated vortical flows

Flow visualization techniques can provide information on high angle of attack separated flows around slender aircraft configurations that may be unobtainable otherwise. At large angles of attack the flow field is dominated by vortical structures originating on the forebody wing extension, wing and forward control surfaces. Several techniques that are suitable for tracking vortices in subsonic wind tunnels are introduced. A discussion of visualization photographs and quantitative data obtained from visualization studies on vortex trajectory and breakdown position on both static and dynamic wind tunnel models is presented.

Nelson, Robert C.↗

Flexible structure control laboratory development and technology demonstration

An experimental structure is described which was constructed to demonstrate and validate recent emerging technologies in the active control and identification of large flexible space structures. The configuration consists of a large, 20 foot diameter antenna-like flexible structure in the horizontal plane with a gimballed central hub, a flexible feed-boom assembly hanging from the hub, and 12 flexible ribs radiating outward. Fourteen electrodynamic force actuators mounted to the hub and to the individual ribs provide the means to excite the structure and exert control forces. Thirty permanently mounted sensors, including optical encoders and analog induction devices provide measurements of structural response at widely distributed points. An experimental remote optical sensor provides sixteen additional sensing channels. A computer samples the sensors, computes the control updates and sends commands to the actuators in real time, while simultaneously displaying selected outputs on a graphics terminal and saving them in memory. Several control experiments were conducted thus far and are documented. These include implementation of distributed parameter system control, model reference adaptive control, and static shape control. These experiments have demonstrated the successful implementation of state-of-the-art control approaches using actual hardware.

Vivian, H. C.↗

Using transonic small disturbance theory for predicting the aeroelastic stability of a flexible wind-tunnel model

The CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code, developed at the NASA - Langley Research Center, is applied to the Active Flexible Wing (AFW) wind tunnel model for prediction of the model's transonic aeroelastic behavior. Static aeroelastic solutions using CAP-TSD are computed. Dynamic (flutter) analyses are then performed as perturbations about the static aeroelastic deformations of the AFW. The accuracy of the static aeroelastic procedure is investigated by comparing analytical results to those from previous AFW wind tunnel experiments. Dynamic results are presented in the form of root loci at different Mach numbers for a heavy gas and air. The resultant flutter boundaries for both gases are also presented. The effects of viscous damping and angle-of-attack, on the flutter boundary in air, are presented as well.

Silva, Walter A.↗

Application of panel methods to wind-tunnel wall interference corrections

Wind-tunnel wall interference effects were estimated using numerical solutions capable of computing the flow field over complex three-dimensional bodies. This approach was then tested by applying it to two typical wind tunnel experiments involving a high-lift wing and a fighter airplane model. In both cases, the static pressure signature along the test section walls was measured and computed for additional validation. The wind-tunnel wall correction method described here, which inherently includes effects of lift and blockage, provides more details than previous semiempirical methods.

Browne, Lindsey↗

Mach 6 testing of two generic three-dimensional sidewall compression scramjet inlets in tetrafluoromethane

Three-dimensional sidewall compression scramjet inlets with leading edge sweeps of 30 and 70 degrees have been tested in the Langley Hypersonic CF4 Tunnel at Mach 6 and a ratio of specific heats of 1.2. The effects of cowl position, contraction ratio, and Reynolds number were investigated. The models were instrumented with 42 static pressure orifices distributed on the sidewalls, baseplate, and cowl. Schlieren movies were made of each test for flow visualization of the entrance plane and cowl region. In order to obtain an approximate characterization of the flow field, a modification to two-dimensional inviscid oblique shock theory was derived to accommodate the three-dimensional effects of leading edge sweep. This theory qualitatively predicted the reflected shock structure/sidewall impingement locations and the observed increase in spillage (flow upturning) with increasing leading edge sweep. The primary effect of moving the cowl forward is capturing the flow which would have otherwise spilled out ahead of the cowl. Increasing the contraction ratio (moving the sidewalls closer together) increases the number of internal shock reflections and hence incrementally increases the sidewall pressure distribution. Significant Reynolds number effects were noted over a small range of Reynolds number.

Holland, Scott D.↗

Using transonic small disturbance theory for predicting the aeroelastic stability of a flexible wind-tunnel model

The CAP-TSD (Computational Aeroelasticity Program-Transonic Small Disturbance) code, developed at the NASA-Langley Research Center, is applied to the Active Flexible Wing (AFW) wind-tunnel model for prediction of the model's transonic aeroelastic behavior. Static aeroelastic solutions using CAP-TSD are computed. Dynamic (flutter) analyses are then performed as perturbations about the static aeroelastic deformations of the AFW. The accuracy of the static aeroelastic procedure is investigated by comparing analytical results to those from previous AFW wind-tunnel experiments. Dynamic results are presented in the form of root loci at different Mach numbers for a heavy gas and air. The resultant flutter boundaries for both gases are also presented. The effects of viscous damping and angle-of-attack, on the flutter boundary in air, are presented as well.

Silva, Walter A.↗

Predicting the aeroelastic behavior of a wind-tunnel model using transonic small disturbance theory

The CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code, developed at the NASA-Langley Research Center, is applied to the Active Flexible Wing (AFW) wind-tunnel model for prediction of the model's transonic aeroelastic behavior. Static aeroelastic solutions using CAP-TSD are computed. Dynamic (flutter) analyses are then performed as perturbations about the static aeroelastic deformations of the AFW. The accuracy of the static aeroelastic procedure is investigated by comparing analytical results to those from AFW wind-tunnel experiments. Dynamic results are presented in the form of root loci at different Mach numbers for a heavy gas and for air test mediums. The resultant flutter boundaries for both gases, and the effects of viscous damping and angle of attack on the flutter boundary in air, are also presented.

Silva, Walter A.↗

Nonlinear response of graphite-epoxy wide columns subject to eccentric load

It is shown that including the effects of bend-twist coupling and material nonlinearity on the large displacement flexural response of graphite-epoxy wide columns is necessary to adequately model their response. Results from static tests on 0(30)T and (30/0/-30 sub 5)s laminated specimens under eccentric axial compression are compared to a nonlinear analysis. The analysis is based on a Kantrovich expansion of the displacements in the width coordinate and a finite element representation in the axial coordinate. An incremental, updated Lagrangian formulation and element corotational coordinates are employed. Nonlinear elastic material behavior was measured in a separate set of material characterization tests, and these data are used to compute tangent stillnesses in the updated configuration.

Griffin, O. H., Jr.↗

Experimental investigation of generic three-dimensional sidewall-compression scramjet inlets at Mach 6 in tetrafluoromethane

Three-dimensional sidewall-compression scramjet inlets with leading-edge sweeps of 30 deg and 70 deg were tested in the Langley Hypersonic CF4 Tunnel at Mach 6 and with a ratio of specific heats of 1.2. The parametric effects of leading-edge sweep, cowl position, contraction ratio, and Reynolds number were investigated. The models were instrumented with 42 static pressure orifices that were distributed on the sidewalls, base plate, and cowl. Schlieren movies were made of each test for flow visualization of the effects of the internal flow spillage on the external flow field. To obtain an approximate characterization of the flow field, a modification to two-dimensional, inviscid, oblique shock theory was derived to accommodate the three-dimensional effects of leading-edge sweep. This theory qualitatively predicted the reflected shock structure (i.e., sidewall impingement locations) and the observed increase in spillage with increasing leading-edge sweep. The primary effect of moving the cowl forward was capturing the flow that would have otherwise spilled out ahead of the cowl. Increasing the contraction ratio increases the number of internal shock reflections and hence incrementally increases the sidewall pressure distribution. Significant Reynolds number effects were noted over a small range of Reynolds number.

Holland, Scott D.↗

Parallel Processing with Digital Signal Processing Hardware and Software

The assembling and testing of a parallel processing system is described which will allow a user to move a Digital Signal Processing (DSP) application from the design stage to the execution/analysis stage through the use of several software tools and hardware devices. The system will be used to demonstrate the feasibility of the Algorithm To Architecture Mapping Model (ATAMM) dataflow paradigm for static multiprocessor solutions of DSP applications. The individual components comprising the system are described followed by the installation procedure, research topics, and initial program development.

Swenson, Cory V.↗

Pressure Distributions at Transonic Speeds for Bumpy and Indented Midsections of a Basic Parabolic-Arc Body

The measured static-pressure distributions at the model surface and in the surrounding flow field are presented for a basic parabolic-arc body having a fineness ratio of 14 and for three additional bodies obtained by modifying the basic parabolic-arc body along the middle portion of the body length by adding a bump, by indenting, or by quadripole shaping. The data were obtained with the various bodies at zero angle of attack. The Mach number varied from 0.80 to 1.20 with a corresponding Reynolds number (based on body length) variation of 27 x 10(exp 6) to 38 x 10(exp 6). The data are subject to tunnel-wall interference and do not represent free-air conditions.

Taylor, Robert A.↗

Experimental Influence Coefficients and Vibration Modes

Test results are presented for both symmetrical and antisymmetrical static loading of a wing model mounted on a three-point support system. The first six free-free vibration modes were determined experimentally. A comparison is made of the symmetrical nodal patterns and frequencies with the symmetrical nodal patterns and frequencies calculated from the experimental influence coefficients.

Weidman, Deene J.↗

Efficient Analysis of Complex Structures

Last various accomplishments achieved during this project are : (1) A Survey of Neural Network (NN) applications using MATLAB NN Toolbox on structural engineering especially on equivalent continuum models (Appendix A). (2) Application of NN and GAs to simulate and synthesize substructures: 1-D and 2-D beam problems (Appendix B). (3) Development of an equivalent plate-model analysis method (EPA) for static and vibration analysis of general trapezoidal built-up wing structures composed of skins, spars and ribs. Calculation of all sorts of test cases and comparison with measurements or FEA results. (Appendix C). (4) Basic work on using second order sensitivities on simulating wing modal response, discussion of sensitivity evaluation approaches, and some results (Appendix D). (5) Establishing a general methodology of simulating the modal responses by direct application of NN and by sensitivity techniques, in a design space composed of a number of design points. Comparison is made through examples using these two methods (Appendix E). (6) Establishing a general methodology of efficient analysis of complex wing structures by indirect application of NN: the NN-aided Equivalent Plate Analysis. Training of the Neural Networks for this purpose in several cases of design spaces, which can be applicable for actual design of complex wings (Appendix F).

Kapania, Rakesh K.↗

Computational Investigation of the Aerodynamic Effects on Fluidic Thrust Vectoring

A computational investigation of the aerodynamic effects on fluidic thrust vectoring has been conducted. Three-dimensional simulations of a two-dimensional, convergent-divergent (2DCD) nozzle with fluidic injection for pitch vector control were run with the computational fluid dynamics code PAB using turbulence closure and linear Reynolds stress modeling. Simulations were computed with static freestream conditions (M=0.05) and at Mach numbers from M=0.3 to 1.2, with scheduled nozzle pressure ratios (from 3.6 to 7.2) and secondary to primary total pressure ratios of p(sub t,s)/p(sub t,p)=0.6 and 1.0. Results indicate that the freestream flow decreases vectoring performance and thrust efficiency compared with static (wind-off) conditions. The aerodynamic penalty to thrust vector angle ranged from 1.5 degrees at a nozzle pressure ratio of 6 with M=0.9 freestream conditions to 2.9 degrees at a nozzle pressure ratio of 5.2 with M=0.7 freestream conditions, compared to the same nozzle pressure ratios with static freestream conditions. The aerodynamic penalty to thrust ratio decreased from 4 percent to 0.8 percent as nozzle pressure ratio increased from 3.6 to 7.2. As expected, the freestream flow had little influence on discharge coefficient.

Deere, K. A.↗

Experimental Evaluation of Verification and Validation Tools on Martian Rover Software

We report on a study to determine the maturity of different verification and validation technologies (V&V) on a representative example of NASA flight software. The study consisted of a controlled experiment where three technologies (static analysis, runtime analysis and model checking) were compared to traditional testing with respect to their ability to find seeded errors in a prototype Mars Rover. What makes this study unique is that it is the first (to the best of our knowledge) to do a controlled experiment to compare formal methods based tools to testing on a realistic industrial-size example where the emphasis was on collecting as much data on the performance of the tools and the participants as possible. The paper includes a description of the Rover code that was analyzed, the tools used as well as a detailed description of the experimental setup and the results. Due to the complexity of setting up the experiment, our results can not be generalized, but we believe it can still serve as a valuable point of reference for future studies of this kind. It did confirm the belief we had that advanced tools can outperform testing when trying to locate concurrency errors. Furthermore the results of the experiment inspired a novel framework for testing the next generation of the Rover.

Brat, Guillaume↗

Probabilistic Analysis and Design of a Raked Wing Tip for a Commercial Transport

An approach for conducting reliability-based design and optimization (RBDO) of a Boeing 767 raked wing tip (RWT) is presented. The goal is to evaluate the benefits of RBDO for design of an aircraft substructure. A finite-element (FE) model that includes eight critical static load cases is used to evaluate the response of the wing tip. Thirteen design variables that describe the thickness of the composite skins and stiffeners are selected to minimize the weight of the wing tip. A strain-based margin of safety is used to evaluate the performance of the structure. The randomness in the load scale factor and in the strain limits is considered. Of the 13 variables, the wing-tip design was controlled primarily by the thickness of the thickest plies in the upper skins. The report includes an analysis of the optimization results and recommendations for future reliability-based studies.

Mason Brian H.↗