Search NASA⌕ Search

SEARCH · Search NASA

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84

CARES/Life Software for Designing More Reliable Ceramic Parts

Products made from advanced ceramics show great promise for revolutionizing aerospace and terrestrial propulsion, and power generation. However, ceramic components are difficult to design because brittle materials in general have widely varying strength values. The CAPES/Life software eases this task by providing a tool to optimize the design and manufacture of brittle material components using probabilistic reliability analysis techniques. Probabilistic component design involves predicting the probability of failure for a thermomechanically loaded component from specimen rupture data. Typically, these experiments are performed using many simple geometry flexural or tensile test specimens. A static, dynamic, or cyclic load is applied to each specimen until fracture. Statistical strength and SCG (fatigue) parameters are then determined from these data. Using these parameters and the results obtained from a finite element analysis, the time-dependent reliability for a complex component geometry and loading is then predicted. Appropriate design changes are made until an acceptable probability of failure has been reached.

Nemeth, Noel N.↗

A Low-Cost Design and Flight Test of the T-38 Inlet

An inlet redesign of the T-38 was completed and flight tested by NASA Johnson Space Center (JSC), Houston Texas. The redesign will allow full gross weight takeoffs from high altitude airports such as El Paso, Texas (ELP) with runway temperatures up to 99 degrees F, an increase of 9 degrees F over the current performance. This project was completed in-house using innovative test techniques. The static thrust of the T-38 was increased 20% with this new inlet.

Johnson, Greg↗

Ground and Flight Evaluation of a Small-Scale Inflatable-Winged Aircraft

A small-scale, instrumented research aircraft was flown to investigate the night characteristics of innersole wings. Ground tests measured the static structural characteristics of the wing at different inflation pressures, and these results compared favorably with analytical predictions. A research-quality instrumentation system was assembled, largely from commercial off-the-shelf components, and installed in the aircraft. Initial flight operations were conducted with a conventional rigid wing having the same dimensions as the inflatable wing. Subsequent flights were conducted with the inflatable wing. Research maneuvers were executed to identify the trim, aerodynamic performance, and longitudinal stability and control characteristics of the vehicle in its different wing configurations. For the angle-of-attack range spanned in this flight program, measured flight data demonstrated that the rigid wing was an effective simulator of the lift-generating capability of the inflatable wing. In-flight inflation of the wing was demonstrated in three flight operations, and measured flight data illustrated the dynamic characteristics during wing inflation and transition to controlled lifting flight. Wing inflation was rapid and the vehicle dynamics during inflation and transition were benign. The resulting angles of attack and of sideslip ere small, and the dynamic response was limited to roll and heave motions.

Murray, James E.↗

Characterization of the Space Shuttle Ascent Debris using CFD Methods

After video analysis of space shuttle flight STS-107's ascent showed that an object shed from the bipod-ramp region impacted the left wing, a transport analysis was initiated to determine a credible flight path and impact velocity for the piece of debris. This debris transport analysis was performed both during orbit, and after the subsequent re-entry accident. The analysis provided an accurate prediction of the velocity a large piece of foam bipod ramp would have as it impacted the wing leading edge. This prediction was corroborated by video analysis and fully-coupled CFD/six degree of freedom (DOF) simulations. While the prediction of impact velocity was accurate enough to predict critical damage in this case, one of the recommendations of the Columbia Accident Investigation Board (CAIB) for return-to-flight (RTF) was to analyze the complete debris environment experienced by the shuttle stack on ascent. This includes categorizing all possible debris sources, their probable geometric and aerodynamic characteristics, and their potential for damage. This paper is chiefly concerned with predicting the aerodynamic characteristics of a variety of potential debris sources (insulating foam and cork, nose-cone ablator, ice, ...) for the shuttle ascent configuration using CFD methods. These aerodynamic characteristics are used in the debris transport analysis to predict flight path, impact velocity and angle, and provide statistical variation to perform risk analyses where appropriate. The debris aerodynamic characteristics are difficult to determine using traditional methods, such as static or dynamic test data, due to the scaling requirements of simulating a typical debris event. The use of CFD methods has been a critical element for building confidence in the accuracy of the debris transport code by bridging the gap between existing aerodynamic data and the dynamics of full-scale, in-flight events.

Murman, Scott M.↗

The Role of Structural Dynamics and Testing in the Shuttle Flowliner Crack Investigation

During a normal inspection of the main propulsion system at Kennedy Space Center, small cracks were noticed near a slotted region of a gimbal joint flowliner located just upstream from one of the Space Shuttle Main Engines (SSME). These small cracks sparked an investigation of the entire Space Shuttle fleet main propulsion feedlines. The investigation was initiated to determine the cause of the small cracks and a repair method that would be needed to return the Shuttle fleet back to operation safely. The cracks were found to be initiated by structural resonance caused by flow fluctuations from the SSME low pressure fuel turbopump interacting with the flowliner. The pump induced backward traveling wakes that excited the liner and duct acoustics which also caused the liner to vibrate in complex mode shapes. The investigation involved an extensive effort by a team of engineers from the NASA civil servant and contractor workforce with the goal to characterize the root cause of the cracking behavior of the fuel side gimbal joint flowliners. In addition to working to identify the root cause, a parallel path was taken to characterize the material properties and fatigue capabilities of the liner material such that the life of the liners could be ascertained. As the characterization of the material and the most probable cause matured, the combination of the two with pump speed restrictions provided a means to return the Shuttle to flight in a safe manner. This paper traces the flowliner investigation results with respect to the structural dynamics analysis, component level testing and hot-fire flow testing on a static testbed. The paper will address the unique aspects of a very complex problem involving backflow from a high performance pump that has never been characterized nor understood to such detail. In addition, the paper will briefly address the flow phenomena that excited the liners, the unique structural dynamic modal characteristics and the variability of SSME operation which has ultimately ensured the safe and reliable operation of the shuttle main engines for each flight.

Frady, Gregory P.↗

Shock Generation and Control Using DBD Plasma Actuators

This report is the final report of a NASA Phase I SBIR contract, with some revisions to remove company proprietary data. The Shock Boundary Layer Interaction (SBLI) phenomena in a supersonic inlet involve mutual interaction of oblique shocks with boundary layers, forcing the boundary layer to separate from the inlet wall. To improve the inlet efficiency, it is desired to prevent or delay shock-induced boundary layer separation. In this effort, Innovative Technology Applications Company (ITAC), LLC and the University of Notre Dame (UND) jointly investigated the use of dielectric-barrier-discharge (DBD) plasma actuators for control of SBLI in a supersonic inlet. The research investigated the potential for DBD plasma actuators to suppress flow separation caused by a shock in a turbulent boundary layer. The research involved both numerical and experimental investigations of plasma flow control for a few different SBLI configurations: (a) a 12 wedge flow test case at Mach 1.5 (numerical and experimental), (b) an impinging shock test case at Mach 1.5 using an airfoil as a shock generator (numerical and experimental), and (c) a Mach 2.0 nozzle flow case in a simulated 15 X 15 cm wind tunnel with a shock generator (numerical). Numerical studies were performed for all three test cases to examine the feasibility of plasma flow control concepts. These results were used to guide the wind tunnel experiments conducted on the Mach 1.5 12 degree wedge flow (case a) and the Mach 1.5 impinging shock test case (case b) which were at similar flow conditions as the corresponding numerical studies to obtain experimental evidence of plasma control effects for SBLI control. The experiments also generated data that were used in validating the numerical studies for the baseline cases (without plasma actuators). The experiments were conducted in a Mach 1.5 test section in the University of Notre Dame Hessert Laboratory. The simulation results from cases a and b indicated that multiple spanwise actuators in series and at a voltage of 75 kVp-p could fully suppress the flow separation downstream of the shock. The simulation results from case c showed that the streamwise plasma actuators are highly effective in creating pairs of counter-rotating vortices, much like the mechanical vortex generators, and could also potentially have beneficial effects for SBLI control. However, to achieve these effects, the positioning and the quantity of the DBD actuators used must be optimized. The wind tunnel experiments mapped the baseline flow with good agreement to the numerical simulations. The experimental results were conducted with spanwise actuators for cases a and b, but were limited by the inability to generate a sufficiently high voltage due to arcing in the wind-tunnel test-section. The static pressure in the tunnel was lower than the static pressure in an inlet at flight conditions, promoting arching and degrading the actuator performance.

Patel, Mehul P.↗

A Cross-Validation Approach to Approximate Basis Function Selection of the Stall Flutter Response of a Rectangular Wing in a Wind Tunnel

The stall flutter response of a rectangular wing in a low speed wind tunnel is modelled using a nonlinear difference equation description. Static and dynamic tests are used to select a suitable model structure and basis function. Bifurcation criteria such as the Hopf condition and vibration amplitude variation with airspeed were used to ensure the model was representative of experimentally measured stall flutter phenomena. Dynamic test data were used to estimate model parameters and estimate an approximate basis function.

Kukreja, Sunil L.↗

Fatigue Life of Postbuckled Structures with Indentation Damages

The fatigue life of composite stiffened panels with indentation damage was investigated experimentally using single stringer compression specimens. Indentation damage was induced on one of the two flanges of each stringer. The experiments were conducted using advanced instrumentation, including digital image correlation, passive thermography, and in-situ ultrasonic scanning. Specimens with initial indentation damage lengths of 32 millimeters to 56 millimeters were tested quasi-statically and in fatigue, and the effects of cyclic load amplitude and damage size were studied. A means of comparison of the damage propagation rates and collapse loads based on a stress intensity measure and the Paris law is proposed.

Davila, Carlos G.↗

Progressive Damage Mechanisms in Thick 3D Composite Structures under Static and Fatigue Loading

The objective of this work is to demonstrate validation of predictive capabilities capturing both damage initiation and growth under static and fatigue loading in geometrically complex three-dimensional (3D) composite structures. The composite structure of interest in the present study resembles a 3D blade spar used in rotorcraft applications. Under both static and fatigue testing, it was shown that damage initiated at the same ply-drop location(s) and grew in the axial as well as hoop directions. CompDam – a state-of-the-art Progressive Damage Analysis (PDA) tool was used to achieve successful correlations of metrics including load-displacement responses and damage modes.

progressive damage analysis↗

Performance of Flash Lidar with Real-time Image Enhancement Algorithm for Landing Hazard Avoidance

Performance of a 3-D imaging flash lidar employing a novel super-resolution algorithm is characterized by a series of static and dynamic tests. A gantry test of this lidar in which the lidar was placed in an instrumented moving basket above a calibrated hazard field proved an excellent demonstration of hazard avoidance capabilities. Results of the gantry test are reported and potential of flash lidar utilizing super-resolution algorithm for future landing missions are explained.

Hazard Detection↗

Finite Element Based Model of Fiber-optic Strain Sensor Mounted on a Semi-monocoque Structure

Fiber-optic strain sensing (FOSS) provides an opportunity for additional awareness and can enable other mitigations such as flutter suppression or gust load alleviation but requires an accurate computational model as part of a design process that integrates structures and controls. A modeling approach for fiber-optic strain sensors has been developed using a shell element formulation in a detailed finite element model. The new FOSS modeling approach is designed to better scale to more complex realistic structures and fiber layouts than previous approaches. The modeling method was applied to the X-56A vehicle and results were compared to experimental static ground-test data. Additionally, the experimental sensor noise of these fiber optic sensors was assessed for the correlations in time and correlations along the fiber. The noise does show significant correlations both in time and along the fibers. These correlations of the noise should also be considered in modeling and assessing algorithms that will use FOSS.

Jeffrey Ouellette↗

Finite Element Based Model of Fiber-optic Strain Sensor Mounted on a Semi-monocoque Structure

Fiber-optic strain sensing (FOSS) provides an opportunity for additional awareness and can enable other mitigations such as flutter suppression or gust load alleviation but requires an accurate computational model as part of a design process that integrates structures and controls. A modeling approach for fiber-optic strain sensors has been developed using a shell element formulation in a detailed finite element model. The new FOSS modeling approach is designed to better scale to more complex realistic structures and fiber layouts than previous approaches. The modeling method was applied to the X-56A vehicle and results were compared to experimental static ground-test data. Additionally, the experimental sensor noise of these fiber optic sensors was assessed for the correlations in time and correlations along the fiber. The noise does show significant correlations both in time and along the fibers. These correlations of the noise should also be considered in modeling and assessing algorithms that will use FOSS.

Jeffrey Ouellette↗

Resistance Spot Weld Failure Mode and Weld Performance for Aluminium Alloys

In this chapter, we present the strength and failure modes of reactive NanoFoil® bonded joints for similar and dissimilar lightweight materials. NanoFoil® is a multi-layer foil fabricated through the growth of thousands of nanoscale layers of aluminum and nickel by vapor deposition. Initiated by an energy impulse, the like-like bonds of the atoms of each layer in the foil are exchanged for more stable unlike bonds between atoms from neighboring layers. As the atoms of each layer mix, heat is generated, creating a self-sustaining reaction traveling along the length of the foil. The instantaneous release of heat energy by this reaction is controlled by the nanolayer thickness and lay-up, such that accurate control of a highly localized heat source can be realized, allowing bonding without compromising the properties/integrities of the base materials. First, solder and braze joints for similar and dissimilar material combinations of steel, aluminum and magnesium are fabricated. Static bond strength tests under tensile shear loading condition are then performed to quantify the bond strength for different material combinations. The through-thickness microstructure changes and modifications by the bonding process are quantified using SEM. Depending on the base material combinations, it is shown that the nanofoil bond strength is comparable to those of the conventional structural adhesive bonds.

36 MATERIALS SCIENCE↗

EGS Collab Project Electrical Resistivity Tomography Characterization and Monitoring

The EGS (Enhanced Geothermal Systems) Collab project is performing stimulation experiments in highly monitored and well-characterized intermediate-scale (~10-20 m) field test beds. The characterization and monitoring system includes an array of electrodes grouted in place within six monitoring wells, with 16 electrodes per well. The electrodes enable characterization of the 3D low-frequency electrical properties of the host rock, and changes in those properties during stimulation and tracer testing using both static and time-lapse Electrical Resistivity Tomography. In this talk we present: 1) ERT array design and installation, 2) baseline (pre-stimulation) imaging results, 3) time-lapse data collected during stimulation operations, and 4) real-time imaging during clean water injections intended to illuminate flow paths as a decrease in bulk electrical conductivity. We will also discuss aspects and lessons learned for conducting ERT imaging operations in the presence of high fluid pressure gradients during stimulation and flow operations. Results to date reveal a highly heterogeneous rock fabric, ranging over four orders of magnitude in bulk electrical conductivity, and high polarization capacity. Baseline imaging results are consistent with borehole logs and core studies. Time-lapse imaging results to identify major flow paths during tracer studies are forthcoming and will be discussed during this presentation. Ultimately the ERT imaging data sets provide useful information for validating and verifying model predictions in preparation for research at DOE’s Frontier Observatory for Research in Geothermal Energy (FORGE).

electrical resistivity tomography, geophysics, geo↗

Recovery of Cs-137 from Electric Arc Furnace Dust - 20562

The present work proposes the Cs-137 recovery from Electric Arc Furnace Dusts (EAFD) by leaching, in order to reduce the volume of radioactive waste to be managed. Leaching tests were performed on different samples of EAFD contaminated with Cs-137. Two leaching methodologies were tested: dynamic and static using as medium distilled water and in some cases NaOH. The results indicate the possibility of recovering Cs-137 from EAFD using the dynamic method; however, the recovery efficiencies of Cs-137 depend on EAFD's chemical composition. The leachates of Cs-137 were quantitatively adsorbed on exchange resins, showing its great potential to isolate or contain the Cs-137 recovery from EAFD. This study shows the feasible to apply the dynamic leaching methodology to recover Cs-137 from EAFD and the use of ion exchange resins for the isolation of removed Cs-137. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ratchet growth in recycled PBX 9502

PBX 9502 is a plastic-bonded high explosive (PBX) containing 95 weight% TATB (triaminotrinitrobenzene) crystals in a polymer binder. TATB crystals are graphitic in nature, with a sheet-like structure and anisotropic CTE. Although the mechanism is not understood, solid-pressed TATB composites have been observed to undergo irreversible volume change ('ratchet growth') upon thermal cycling . This phenomenon has been studied but many aspects remain elusive and uncharacterized. Engineering or performance changes associated with ratchet growth have often been attributed to changes in density alone. We propose that the density changes which accompany ratchet growth involve a unique form of micro-damage distinguishable from the pore structure associated with low-pressed density. We have performed ratchet growth studies on Recycled PBX 9502 between -54 to 80{sup o}C with density changes of about 1.5%. Specimens of the same density were obtained using a lower pressure in the manufacturing process. Comparative measurements were made using quasi-static uniaxial tension tests, as well as micro x-ray computed tomography and ultra-small angle neutron scattering experiments. Through these measurements we have shown that ratchet grown PBX 9502 has properties quite different from predictions based on density alone. The pore size distribution of ratchet grown specimens is unique and easily distinguished from parts pressed to an equivalent density.

36 MATERIALS SCIENCE↗

Characterization of Mode I and mixed-mode delamination growth in T300/5208 graphite/epoxy

The roles played by Mode I and Mode II strain-energy release rates (G-I and G-II, respectively) in inducing delamination growth under static and fatigue loading were investigated, using T300/5208 graphite/epoxy specimens. Double cantilever beam (DCB) specimens and cracked lap shear (CLS) specimens were used for pure Mode I and mixed-mode tests, respectively. Fatigue-induced delamination growth was characterized by constant-amplitude fatigue tests at a minimum to maximum cyclic load ratio of 0.05 and a frequency of 10 Hz. During the tests, the maximum and minimum strain-energy release rates (Gmax, Gmin) and the delamination growth rate (da/dN) were monitored. Static tests on mixed-mode CLS specimens measured the total strain-energy release rate, which was broken into G-I and G-II components using finite-element analysis. A power-law relationship between da/dN and G-Imax, and da/dN and Gmax were obtained from fatigue test results on DCB and CLS specimens, respectively. The power law for a pure Mode II delamination was derived from CLS results by subtracting the contribution due to G-I.

Ramkumar, R. L.↗