Surface Meteorological Station - UND 10m, (2) Sonics 3m 10m, (2) T/RH 3m 10m (1) Licor 3m, Physics site-1 - Raw Data
The data included features wind, temperature, and turbulence measurements.
17 WIND ENERGY↗
SEARCH · Search NASA
Results for “surface physics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Results From Mars Show Electrostatic Charging of the Mars Pathfinder Sojourner Rover
Indirect evidence (dust accumulation) has been obtained indicating that the Mars Pathfinder rover, Sojourner, experienced electrostatic charging on Mars. Lander camera images of the Sojourner rover provide distinctive evidence of dust accumulation on rover wheels during traverses, turns, and crabbing maneuvers. The sol 22 (22nd Martian "day" after Pathfinder landed) end-of-day image clearly shows fine red dust concentrated around the wheel edges with additional accumulation in the wheel hubs. A sol 41 image of the rover near the rock "Wedge" (see the next image) shows a more uniform coating of dust on the wheel drive surfaces with accumulation in the hubs similar to that in the previous image. In the sol 41 image, note particularly the loss of black-white contrast on the Wheel Abrasion Experiment strips (center wheel). This loss of contrast was also seen when dust accumulated on test wheels in the laboratory. We believe that this accumulation occurred because the Martian surface dust consists of clay-sized particles, similar to those detected by Viking, which have become electrically charged. By adhering to the wheels, the charged dust carries a net nonzero charge to the rover, raising its electrical potential relative to its surroundings. Similar charging behavior was routinely observed in an experimental facility at the NASA Lewis Research Center, where a Sojourner wheel was driven in a simulated Martian surface environment. There, as the wheel moved and accumulated dust (see the following image), electrical potentials in excess of 100 V (relative to the chamber ground) were detected by a capacitively coupled electrostatic probe located 4 mm from the wheel surface. The measured wheel capacitance was approximately 80 picofarads (pF), and the calculated charge, 8 x 10(exp -9) coulombs (C). Voltage differences of 100 V and greater are believed sufficient to produce Paschen electrical discharge in the Martian atmosphere. With an accumulated net charge of 8 x 10(exp -9) C, and average arc time of 1 msec, arcs can also occur with estimated arc currents approaching 10 milliamperes (mA). Discharges of this magnitude could interfere with the operation of sensitive electrical or electronic elements and logic circuits. Sojourner rover wheel tested in laboratory before launch to Mars. Before launch, we believed that the dust would become triboelectrically charged as it was moved about and compacted by the rover wheels. In all cases observed in the laboratory, the test wheel charged positively, and the wheel tracks charged negatively. Dust samples removed from the laboratory wheel averaged a few ones to tens of micrometers in size (clay size). Coarser grains were left behind in the wheel track. On Mars, grain size estimates of 2 to 10 mm were derived for the Martian surface materials from the Viking Gas Exchange Experiment. These size estimates approximately match the laboratory samples. Our tentative conclusion for the Sojourner observations is that fine clay-sized particles acquired an electrostatic charge during rover traverses and adhered to the rover wheels, carrying electrical charge to the rover. Since the Sojourner rover carried no instruments to measure this mission's onboard electrical charge, confirmatory measurements from future rover missions on Mars are desirable so that the physical and electrical properties of the Martian surface dust can be characterized. Sojourner was protected by discharge points, and Faraday cages were placed around sensitive electronics. But larger systems than Sojourner are being contemplated for missions to the Martian surface in the foreseeable future. The design of such systems will require a detailed knowledge of how they will interact with their environment. Validated environmental interaction models and guidelines for the Martian surface must be developed so that design engineers can test new ideas prior to cutting hardware. These models and guidelines cannot be validated without actual flighata. Electrical charging of vehicles and, one day, astronauts moving across the Martian surface may have moderate to severe consequences if large potential differences develop. The observations from Sojourner point to just such a possibility. It is desirable to quantify these results. The various lander/rover missions being planned for the upcoming decade provide the means for doing so. They should, therefore, carry instruments that will not only measure vehicle charging but characterize all the natural and induced electrical phenomena occurring in the environment and assess their impact on future missions.
Kolecki, Joseph C.↗
Quantum dynamics of a molecular emitter strongly coupled with surface plasmon polaritons: A macroscopic quantum electrodynamics approach
In this work, we study a molecular emitter above a silver surface in the framework of macroscopic quantum electrodynamics and explore the population dynamics including non-Markovian effects. The theory we present is general for molecular fluorescence in the presence of dielectrics with any space-dependent, frequency-dependent, or complex dielectric functions. Furthermore, the proposed theory allows us to calculate the memory kernel of polaritons using computational electrodynamics packages. In the limit of a high vibration frequency, the different strengths of exciton-polariton couplings lead to distinct characteristics in the population dynamics, e.g., Franck-Condon-Rabi oscillation. (The frequency of Rabi oscillation is dependent on the Franck-Condon factor.) Additionally, in a specific condition, we derive a parameter-free formula that can be used to estimate the exciton-polariton coupling between a molecular emitter and a nanocavity, and the coupling estimated by our theory is in good agreement with the reported experimental results.
Surface plasmon polaritons↗
Multiphysics modeling of mesh piezoelectric atomizers
An ultrasonic clothes dryer was developed by researchers at Oak Ridge National Laboratory based on a novel approach of using high-frequency mechanical vibration instead of heat to extract moisture as a cold mist. This technology is based on direct mechanical coupling between mesh piezoelectric (PZT) transducers and wet fabric. The vibration introduces sufficient momentum to the droplets trapped in the fabric pores to atomize them and leave the garment in a cold state. In the vibrating transducer, deformation followed by the effects of boundary layer acoustic streaming results in ejection of the atomized droplets. The research presented bridges the vibration of a PZT mesh transducer to the induced acoustic field and to capillary-wave theory. Mathematical modeling studies free and forced vibrations of a mesh-like PZT structure, using the structural parameters identified by actuation testing in several case studies. Computational fluid–structure interaction modeling is performed to couple the vibrations of a PZT transducer with an in-contact droplet. The results obtained are used to investigate (1) the transverse deformation of the vibrating mesh transducer in contact with a droplet, (2) the resultant boundary layer acoustic streaming in the fluid surrounding the vibrating surface, and (3) the droplet deformation and fluid ejection. The physics of atomization are linked to the level of the near-wall droplet vibrations induced by the surface deformation of the transducer. Then the surface deformation is linked to the properties of the PZT mesh transducer and input actuation frequency and power.
Dupuis, Eric↗
Activities of the Center for Space Construction
The Center for Space Construction (CSC) at the University of Colorado at Boulder is one of eight University Space Engineering Research Centers established by NASA in 1988. The mission of the center is to conduct research into space technology and to directly contribute to space engineering education. The center reports to the Department of Aerospace Engineering Sciences and resides in the College of Engineering and Applied Science. The college has a long and successful track record of cultivating multi-disciplinary research and education programs. The Center for Space Construction is prominent evidence of this record. At the inception of CSC, the center was primarily founded on the need for research on in-space construction of large space systems like space stations and interplanetary space vehicles. The scope of CSC's research has now evolved to include the design and construction of all spacecraft, large and small. Within this broadened scope, our research projects seek to impact the underlying technological basis for such spacecraft as remote sensing satellites, communication satellites, and other special purpose spacecraft, as well as the technological basis for large space platforms. The center's research focuses on three areas: spacecraft structures, spacecraft operations and control, and regolith and surface systems. In the area of spacecraft structures, our current emphasis is on concepts and modeling of deployable structures, analysis of inflatable structures, structural damage detection algorithms, and composite materials for lightweight structures. In the area of spacecraft operations and control, we are continuing our previous efforts in process control of in-orbit structural assembly. In addition, we have begun two new efforts in formal approach to spacecraft flight software systems design and adaptive attitude control systems. In the area of regolith and surface systems, we are continuing the work of characterizing the physical properties of lunar regolith, and we are at work on a project on path planning for planetary surface rovers.
Source record↗
Microsecond Electron Beam Source with Electron Energy Up to 400 Kev and Plasma Anode
A new high-power source of electrons with plasma anode for producing high-current microsecond electron beams with electron energy up to 400 keV has been developed, manufactured, and put in operation. To increase the cross section and pulse current duration of the beam, a multipoint explosive emission cathode is used in the electron beam source, and the beam is formed in an applied external guiding magnetic field. The Marx generator with vacuum insulation is used as a high-voltage source. Electron beams with electron energy up to 300–400 keV, current of 5–15 kA, duration of 1.5–3 μs, energy up to 4 kJ, and cross section up to 150 cm{sup 2} have been produced. The operating modes of the electron beam source are realized in which the applied voltage is influenced weakly on the current. The possibility of source application for melting of metal surfaces is demonstrated.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Science Opportunities on the Lunar Surface and Gateway
The presentation will be made at the International Microgravity Strategic Planning Group (IMSPG). The presentation is an overview of the science platforms for physical and fundamental physics in near lunar orbit on on the moon's surface. The presentation includes some timeline information for lunar missions. All of the information in the presentation is publicly available.
Kevin Sato↗
Electron-Stimulated Desorption of Sodium and Potassium Atoms from Oxidized Tungsten
We have analyzed electron-stimulated desorption (ESD) of neutral sodium and potassium atoms on oxidized tungsten. We propose a model describing ESD of atoms from the oxidized tungsten surface.
74 ATOMIC AND MOLECULAR PHYSICS↗
Methods for Measuring and Computing the Reference Temperature in Newton’s Law of Cooling for External Flows
Newton’s law of cooling requires a reference temperature (𝑇 𝑟𝑒𝑓 ) to define the heat-transfer coefficient (ℎ). For external flows with multiple temperatures in the freestream, obtaining 𝑇 𝑟𝑒𝑓 is a challenge. One widely used method, referred to as the adiabatic-wall (AW) method, obtains 𝑇 𝑟𝑒𝑓 by requiring the surface of the solid exposed to convective heat transfer to be adiabatic. Another widely used method, referred to as the linear-extrapolation (LE) method, obtains 𝑇 𝑟𝑒𝑓 by measuring/computing the heat flux ($𝑞^{′′}_𝑠$) on the solid surface at two different surface temperatures (𝑇 𝑠 ) and then linearly extrapolating to $𝑞^{′′}_𝑠$ = 0. A third recently developed method, referred to as the state-space (SS) method, obtains 𝑇 𝑟𝑒𝑓 by probing the temperature space between the highest and lowest in the flow to account for the effects of 𝑇 𝑠 or $𝑞^{′′}_𝑠$ on 𝑇 𝑟𝑒𝑓 . This study examines the foundation and accuracy of these methods via a test problem involving film cooling of a flat plate where $𝑞^{′′}_𝑠$ switches signs on the plate’s surface. Results obtained show that only the SS method could guarantee a unique and physically meaningful 𝑇 𝑟𝑒𝑓 where 𝑇 𝑠 =𝑇 𝑟𝑒𝑓 on a nonadiabatic surface $𝑞^{′′}_𝑠$ = 0. The AW and LE methods both assume 𝑇 𝑟𝑒𝑓 to be independent of 𝑇 𝑠 , which the SS method shows to be incorrect. Though this study also showed the adiabatic-wall temperature, 𝑇 𝐴𝑊 , to be a good approximation of 𝑇 𝑟𝑒𝑓 (<10% relative error), huge errors can occur in ℎ about the solid surface where |𝑇 𝑠 −𝑇 𝐴𝑊 | is near zero because where 𝑇 𝑠 =𝑇 𝐴𝑊 , $𝑞^{′′}_𝑠$ ≠ 0.
Newton's law of cooling↗
Modeling surface deformations at complex strike-slip plate boundaries
Two new versions of the physical base-traction model of Li and Rice (1987) have been developed to study the loading processes and surface deformation near plate boundaries with geometric complexities, including a shallow creeping fault segment and two subparallel faults. Predictions of surface velocity and surface slip rate for the region between the San Andreas fault and the Pacific coast at the latitude of the Parkfield-Cholame segment using model parameters based on geologic, geodetic, and seismic considerations were found to be in good agreement with contemporary geodetic field data (not used in constrainning model parameters). Also, predicted surface velocity for the Salton Sea-Coachella Valley area were fit to recently derived contemporary geodetic data and very large baseline interferometry data, althoug here the model parameters are not well constrained.
Li, Victor C.↗
ARPA-E PNDIODES "PN Junctions by Ion Implantation" Project (Final Report)
Electricity accounts for nearly 40% of the energy generated in the United States, of which 65% is lost to electrical system inefficiency before reaching end-use sectors. Power electronics will play a growing role in this distribution and end-use, with up to 80% of electricity estimated to pass through power electronics from generation to consumption by 2030. This gives technical improvements in power electronics enormous potential to drive efficiency gains throughout the U.S. economy. Current Si-based power architectures including MOSFETs and IGBTs are limited by high losses, low switching frequency, and poor high-temperature performance. Given the material properties of GaN, devices can exhibit a given turn-on resistance and breakdown voltage with a minute fraction of the area of a Si device—all with higher switching speeds. While n-type doping of III-nitrides has reached a high level of maturity and integration into commercialized products, p-type doping presents distinct challenges that requires continued research. The success of the next generation of GaN-based power devices depends in large part on the ability to form selective-area p-type regions, which can be accomplished by ion implantation of the prevailing acceptor dopant, Mg. This approach is relatively inexpensive and is a fab-ready processing step for creation of current-generation power electronic devices including BJTs, IGBTs, and diode rectifiers. However, ion implantation induces lattice damage and creates point defects within the material, which negatively impacts dopant activation annealing. These forms of damage may be removed by high-temperature annealing, however short annealing time and higher pressures are required to prevent decomposition of the material. We approach this challenge through an innovative combination of approaches toward obtaining high-conductivity p-type GaN. By the novel employment of a gyrotron, a microwave source that can be shaped into a highly localized beam to dissipate very high power in a semiconductor target, a wafer of GaN can be annealed in short (<2 s) ‘pulses’ at temperatures of 1450 °C (2640 °F) to achieve p-type activation without appreciable surface degradation. The p-type activation of Mg-implanted GaN can be further aided by co-implantation with N, believed to enhance the removal of point defects that compensate the acceptors dopant. Elevation to such high temperatures for even a short time induces degradation of GaN-to overcome, we have implemented additional measures to retain high-quality crystalline GaN while removing implant damage and activating Mg dopant. A bilayer cap of AlN is deposited by a combination of chemical and physical vapor deposition to protect the GaN surface. To prevent decomposition of GaN loss of N during annealing, a custom vessel—to contain pressurized N while allowing injection of microwave energy—is employed. By detailed study of the interaction of various measures that are implemented to protect the sample surface (GaN), activate the implanted dopants, and mitigate damage of the lattice heating damage during annealing, we are able to achieve p-type GaN and observe recovery of the crystal and removal of substantial density of defects created during the implantation process.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Visible-infrared properties of controlled laboratory soils
Almost all surfaces available for remote observation consist of particulate materials or soils. The distribution of mean particle sizes depend on the original material and physical and chemical processes that have acted on the surface over time. It is well known that the optical and infrared spectral properties of materials depends on the particle size. There has been little detailed study, however, of natural soils, namely particulate materials with a range of particle sizes. Current models for intimate mixing typically use an average particle size in calculations and are most successful when the particle size is constrained by known sieve fractions. Preliminary results of a study in which soils were prepared with a known composition and range of particle sizes are reported. This discussion presents the overall visible to infrared properties of these synthetic soils and evaluates the mid-infrared properties.
Pieters, C. M.↗
Precipitation Meteorological Instruments (PRECIPMET) Handbook
The PRECIPMET surface meteorology instrument system provides temperature, relative humidity, pressure, wind speed and direction, and precipitation data relevant to the precipitation network instruments: laser disdrometer (PARS2) and radar wind profiler (RWP). The PRECIPMET is installed at the intermediate facilities (IF) of the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) atmospheric observatory. The instrument system consists of a Vaisala WXT520 weather transmitter and a 12”-diameter Novalynx tipping bucket rain gauge (TBRG). The WXT520 is mounted on top of the control building at a height of approximately 4 meters. The tipping bucket is mounted on a pole level with the surrounding fencing (approximately 2 meters) to prevent physical interference with the gauge.
54 ENVIRONMENTAL SCIENCES↗
Effect of charge selective contacts on the quasi Fermi level splitting of CuGa 3 Se 5 thin film photocathodes for hydrogen evolution and methylviologen reduction
The defect-copper chalcopyrite CuGa 3 Se 5 is a promising photocathode material for solar hydrogen generation. Here we assess its performance with photoelectrochemical measurements and vibrating Kelvin probe surface photovoltage spectroscopy.
14 SOLAR ENERGY↗
Crystallographic analysis of nano-tendril bundle vs fuzz growth on tungsten exposed to helicon wave-coupled helium plasma
The propensity for nano-tendril bundle (NTB) vs widespread nano-tendril growth (i.e., fuzz) on polycrystalline W under varying ion energy modulation conditions, from DC to peak-to-peak energy modulation of 42 eV at 13.56 MHz, is correlated with the crystal orientation of the underlying grains. Grains that are vicinal to crystal orientations with high surface diffusivity (e.g., {101} for a body centered cubic crystal structure) exhibit NTB growth at lower ion energy modulation amplitude than grains that are vicinal to low surface diffusivity orientations, such as {100}. Adatom mobility considerations are presented to describe the experimental observations. These results support that surface diffusion or W adatom mobility enhanced by ion bombardment plays a key role in the surface morphology evolution of W under He irradiation.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Modeling soil temperature in a temperate region: A comparison between empirical and physically based methods in SWAT
Although Soil and Water Assessment Tool (SWAT) has been widely used in temperate regions, the performance of its soil temperature module has not been extensively assessed. The aim of the present study was to evaluate the performance of the SWAT model’s built-in empirical soil temperature module and a physically-based soil temperature algorithm using four years of daily soil temperature measurements at three depths (i.e., 5, 10, and 50 cm) across 10 monitoring stations in and around the Choptank River watershed, Maryland, USA. Two versions of physically-based soil temperature module were considered: one was calibrated using parameter values adopted from previous studies, another one remained calibrated. Results show that the empirical soil temperature module and both versions of physically-based soil temperature module reproduce well variations of measured soil temperatures at 5 and 10 cm depths for all stations in non-winter seasons. However, the empirical and uncalibrated physically-based soil temperature modules tended to underestimate soil temperatures in non-winter seasons at the deeper soil layer (50 cm depth); they also severely underestimated soil temperatures in winter for soil surface layers (5 and 10 cm depths). Results indicate that the calibrated physically-based soil temperature module improved soil temperature simulation, especially for winter due to its accounting for insulation effect of crop residue on soil surface. This study suggested that when equipping a physically-based soil temperature module in a hydrological model, a better representation of surface residue was needed for applications in agricultural watersheds and assessing best management practices.
soil temperature, surface residue, heat transfer, ↗
Pore-Scale Dynamics of Liquid CO2–Water Displacement in 2D Axisymmetric Porous Micromodels Under Strong Drainage and Weak Imbibition Conditions: High-Speed μPIV Measurements
Resolving pore-scale transient flow dynamics is crucial to understanding the physics underlying multiphase flow in porous media and informing large-scale predictive models. Surface properties of the porous matrix play an important role in controlling such physics, yet interfacial mechanisms remain poorly understood, in part due to a lack of direct observations. This study reports on an experimental investigation of the pore-scale flow dynamics of liquid CO 2 and water in two-dimensional (2D) circular porous micromodels with different surface characteristics employing high-speed microscopic particle image velocimetry (μPIV). The design of the micromodel minimized side boundary effects due to the limited size of the domain. The high-speed μPIV technique resolved the spatial and temporal dynamics of multiphase flow of CO 2 and water under reservoir-relevant conditions, for both drainage and imbibition scenarios. When CO 2 displaced water in a hydrophilic micromodel (i.e., drainage), unstable capillary fingering occurred and the pore flow was dominated by successive pore-scale burst events (i.e., Haines jumps). When the same experiment was repeated in a nearly neutral wetting micromodel (i.e., weak imbibition), flow instability and fluctuations were virtually eliminated, leading to a more compact displacement pattern. Energy balance analysis indicates that the conversion efficiency between surface energy and external work is less than 30%, and that kinetic energy is a disproportionately smaller contributor to the energy budget. This is true even during a Haines jump event, which induces velocities typically two orders of magnitude higher than the bulk velocity. These novel measurements further enabled direct observations of the meniscus displacement, revealing a significant alteration of the pore filling mechanisms during drainage and imbibition. While the former typically featured burst events, which often occur only at one of the several throats connecting a pore, the latter is typically dominated by a cooperative filling mechanism involving simultaneous invasion of a pore from multiple throats. This cooperative filling mechanism leads to merging of two interfaces and releases surface energy, causing instantaneous high-speed events that are similar, yet fundamentally different from, burst events. Finally, pore-scale velocity fields were statistically analyzed to provide a quantitative measure of the role of capillary effects in these pore flows.
Li, Yaofa↗
Numerical benchmark of transient pressure-driven metallic melt flows
Fluid dynamics simulations of melting and crater formation at the surface of a copper cathode exposed to high plasma heat fluxes and pressure gradients are presented. The predicted deformations of the free surface and the temperature evolution inside the metal are benchmarked against previously published simulations. Despite the physical model being entirely hydrodynamic and ignoring a variety of plasma–surface interaction processes, the results are also shown to be remarkably consistent with the predictions of more advanced models, as well as experimental data. This provides a sound basis for future applications of similar models to studies of transient surface melting and droplet ejection from metallic plasma-facing components after disruptions.
36 MATERIALS SCIENCE↗