Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Analysis of LOCA Scenarios in the NIST Research Reactor Before and After Fuel Conversion

An analysis has been done of hypothetical loss-of-coolant-accidents (LOCAs) in the research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The purpose of the analysis is to determine if the peak clad temperature remains below the Safety Limit, which is the blister temperature for the fuel. The configuration of the NBSR considered in the analysis is that projected for the future when changes will be made so that shutdown pumps do not operate when a LOCA signal is detected. The analysis was done for the present core with high-enriched uranium (HEU) fuel and with the proposed low-enriched uranium (LEU) fuel that would be used when the NBSR is converted from one to the other. The analysis consists of two parts. The first examines how the water would drain from the primary system following a break and the possibility for the loss of coolant from within the fuel element flow channels. This work is performed using the TRACE system thermal-hydraulic code. The second looks at the fuel clad temperature as a function of time given that the water may have drained from many of the flow channels and the water in the vessel is in a quasi-equilibrium state. The temperature behavior is investigated using the three-dimensional heat conduction code HEATING7.3. The results in all scenarios considered for both HEU and LEU fuel show that the peak clad temperature remains below the blister temperature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Neutronic Consideration of TREAT Facility Fuel SiC Recladding

The Transient Reactor Test (TREAT) Facility is an air-cooled reactor composed of graphite-urania fuel encapsulated in zirconium alloy canisters and surrounded by ~2 ft (~61 cm) of nuclear grade graphite. The primary role of TREAT is to provide in-pile nuclear-heated safety research via transient testing [1]. Benchmark efforts have demonstrated sensitivity of TREAT neutronics models to graphite cross section data and key neutron poisons found in the fuel assemblies [2]. During fabrication of TREAT fuel assemblies, a small concentration of boron was inadvertently introduced with variable concentration into the aggregate of fuel blocks prepared for TREAT use. The concentration of boron, and its respective uncertainty, represent the most sensitive component in a neutronics study; unfortunately, nothing can be done to reduce or otherwise mitigate its impact. Hydrogen in the fuel blocks reduces the mean free path of the core and its true quantity and uncertainty is approximated. The hydrogen remains from pitch binder used in the fuel fabrication process and was not completely released due to incomplete fuel graphitization. Destructive fuel testing is necessary to quantify the actual hydrogen content and to improve benchmark model quality. A third neutron poison of some significance is the hafnium impurity in the Zircaloy-3 (Zry-3) assembly cladding. The quantity of hafnium is expected to be within nominal manufacturing limits for nuclear grade zircaloy. Recladding the fuel assemblies with material that is less neutron absorbing is expected to benefit reactor neutron economy. Moreover, TREAT’s total transient energy is restricted based on the rate of Zry-3 oxidation in TREAT’s air coolant environment. Hence, cladding with more benign air reaction kinetics could dramatically uprate the facility’s experimental capability. Silicon carbide (SiC) has been proposed as a candidate material for recladding TREAT assemblies, as SiC/SiC demonstrate favorable properties within nuclear environments [3]. The current operational limits of TREAT are restricted by the oxidation of Zry-3. Change of the cladding to SiC could feasibly double the current temperature limitation. Recladding opportunities allow for previously damaged fuel assemblies to be returned to service, as Zry-3 is not commercially available. The initial effort required to consider proceeding with any recladding effort is to neutronically characterize key reactor parameters while replacing Zry-3 with SiC. A characterization summary, with respective results, is provided herein.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dry Storage of Research Reactor Spent Nuclear Fuel - 13321

Spent fuel from domestic and foreign research reactors is received and stored at the Savannah River Site's L Area Material Storage (L Basin) Facility. This DOE-owned fuel consists primarily of highly enriched uranium in metal, oxide or silicide form with aluminum cladding. Upon receipt, the fuel is unloaded and transferred to basin storage awaiting final disposition. Disposition alternatives include processing via the site's H Canyon facility for uranium recovery, or packaging and shipment of the spent fuel to a waste repository. A program has been developed to provide a phased approach for dry storage of the L Basin fuel. The initial phase of the dry storage program will demonstrate loading, drying, and storage of fuel in twelve instrumented canisters to assess fuel performance. After closure, the loaded canisters are transferred to pad-mounted concrete overpacks, similar to those used for dry storage of commercial fuel. Unlike commercial spent fuel, however, the DOE fuel has high enrichment, very low to high burnup, and low decay heat. The aluminum cladding presents unique challenges due to the presence of an oxide layer that forms on the cladding surface, and corrosion degradation resulting from prolonged wet storage. The removal of free and bound water is essential to the prevention of fuel corrosion and radiolytic generation of hydrogen. The demonstration will validate models predicting pressure, temperature, gas generation, and corrosion performance, provide an engineering scale demonstration of fuel handling, drying, leak testing, and canister backfill operations, and establish 'road-ready' storage of fuel that is suitable for offsite repository shipment or retrievable for onsite processing. Implementation of the Phase I demonstration can be completed within three years. Phases II and III, leading to the de-inventory of L Basin, would require an additional 750 canisters and 6-12 years to complete. Transfer of the fuel from basin storage to dry storage requires integration with current facility operations, and selection of equipment that will allow safe operation within the constraints of existing facility conditions. Examples of such constraints that are evaluated and addressed by the dry storage program include limited basin depth, varying fuel lengths up to 4 m, (13 ft), fissile loading limits, canister closure design, post-load drying and closure of the canisters, instrument selection and installation, and movement of the canisters to storage casks. The initial pilot phase restricts the fuels to shorter length fuels that can be loaded to the canister directly underwater; subsequent phases will require use of a shielded transfer system. Removal of the canister from the basin, followed by drying, inerting, closure of the canister, and transfer of the canister to the storage cask are completed with remotely operated equipment and appropriate shielding to reduce personnel radiation exposure. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Experimental test plan for PWR sister rods in the high burnup spent fuel data project

The High Burnup Spent Fuel Data Project (herein referred to as the 'project'), sponsored by the US Department of Energy (DOE) Office of Nuclear Energy (NE), is focused on experimentally defining the effects of long-term storage and transportation on high burnup (HBU) pressurized water reactor (PWR) fuel (>45 gigawatt days per metric ton uranium). The goals of the project are to provide confirmatory data for model validation and potential improvement; to provide input to future dry storage cask design; to support license renewals and new licenses for Independent Spent Fuel Storage Installation facilities; and to support transportation licensing for high burnup used fuel. In support of these project goals, an instrumented TN-32B bolted-lid cask at the North Anna reactor site will be loaded with intact, HBU PWR fuel assemblies (project assemblies) having four different kinds of cladding: standard Zircaloy-4, low-tin Zircaloy-4, ZIRLO, and M5. In approximately 10 years, the instrumented cask will be opened for inspection and several fuel rods from the project assemblies will be characterized. To support the project goals, the project pulled 25 'sister rods', 9 from the project assemblies and 16 from similar HBU assemblies, for characterization. The 25 sister rods are all high burnup and cover the range of cladding alloys. The 25 sister rods were shipped to Oak Ridge National Laboratory (ORNL) in early 2016 for detailed nondestructive and destructive examination. Examinations are intended to provide baseline data on the initial physical state of the cladding and fuel prior to the loading, drying, and long-term dry storage process. Further examinations are focused on determining the effects of temperatures encountered during and following drying. Similar tests will be performed on rods taken from the project assemblies at the end of the storage period (the 'cask rods') to identify any significant changes in the fuel rods that may have occurred during the dry storage period. Additionally, some of the sister rods will be used for separate effects testing to expand the applicability of the project data to the fleet, and to address some of the data-related gaps associated with extended storage and subsequent transportation of high burnup fuel. A draft test plan is being developed that describes the experimental work to be conducted on the sister rods. This paper summarizes the draft test plan and necessary coordination activities for the multi-year experimental program to supply data relevant to the assessment of the safety of long-term storage followed by transportation of high burnup used fuel. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Determination of the mechanical properties of blisters by nanoindentation

In light-water reactors, a zirconium oxide layer will be formed at the outer surface of the fuel cladding as a consequence of the chemical reaction which takes place between zirconium and the cooling water. This zirconium oxide layer is a good thermal insulator, but at some point, it may spall-out. As a consequence, a cold spot will be formed at the outer surface of the cladding. In this situation, the hydrogen will quickly migrate to this spot to form a highly-enriched hydride zone, known as blister. In this work, an experimental procedure has been devised to produce blisters with a similar shape to the ones reported in the literature for irradiated cladding with severe hydriding. Nano-indentation tests were performed on blisters prepared in laboratory. A numerical simulation by the finite element method was developed to fit the load versus penetration depth data from the aforementioned nano-indentation tests. By means of an inverse process which combines experimental data and numerical simulations, the constitutive equation of the blister was determined. The process has been used to calculate the plastic stress-strain curve of the blister under study at room temperature. The results show an almost perfect numerical fitting of the experimental data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Preliminary analysis of core heat-up for ATFs under accident conditions

The accident-tolerant fuel (ATF) system is aim at upgrading safety characteristics of the nuclear fuel and cladding in a reactor core where active cooling has been lost, and is preferable or comparable to the conventional UO{sub 2}-Zr fuel system when the reactor is in normal operation. In this paper, the improved performance of UO{sub 2}-SiC, UO{sub 2}-FeCrAl fuel systems, and of fully ceramic micro-encapsulated (FCM) fuels: FCM-SiC and FCM-FeCrAl, on the core heat-up progress in a pressurized water reactor (PWR) is analyzed by using the best-estimate system code RELAP5 and severe accident analysis program. For this purpose two accident scenarios are selected: a large break LOCA as a design base accident and an extended station blackout (SBO) severe accident. For the LBLOCA with just low-pressure safety injection, larger volumetric heat capacity and thermal conductivity of ATF materials contribute to a larger safety margin in terms of the peak cladding temperature compared with UO{sub 2}-Zr. Thanks to higher melting temperatures, FCM-SiC is failed by melting almost 1200 s later than UO{sub 2}-Zr. The accumulated production of hydrogen for ATF materials is around 10 times smaller than that for UO{sub 2}-Zr. However, high temperature oxidation of SiC cladding generates carbon monoxide which is combustible, while the melting point of FeCrAl is not high enough. In the SBO scenario with mitigation measure, the advantage of ATF is more evident. If the mitigation measure could not be taken, core heatup is inevitable for all types of fuel system, but the temperature rising of ATF core is much slower. In general, improved high-temperature properties and resistance to oxidation play important roles for ATF cores.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A study on the assessment criteria of DHC in PWR spent fuel

One of the major degradation mechanisms of PWR spent fuel cladding is delayed hydride cracking (DHC), which can activate within a relatively low temperature range. Its maximum crack growth rate is estimated to be within the range of 10{sup -7} m/s, at which the cladding can rupture in 1 to 2 years during dry storage. For this reason, it is essential to prevent DHC crack growth itself, but most of the existing DHC studies have been focused on the crack growth rate. In this regard, the values and characteristics of the threshold stress intensity factor (K{sub IH}) for PWR Zircaloy-4 cladding were described. Based on the limited existing test results and analysis, the experimentally measured K{sub IH} were compared with the predicted K{sub IH}. The comparison shows that the predicted values are much lower than the measured ones and both theoretical estimation and measured values of K{sub IH} increase as the temperature increases. The possibilities of degradation by DHC were also discussed during long-term dry storage. For a more reliable analysis, additional information on a pre-existing crack of spent fuel is needed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advances in Westinghouse fuel rod design technology (PAD5)

The Westinghouse Performance Analysis and Design (PAD) code for light-water reactors has been recently updated to version PAD5 and submitted to NRC for review. PAD5 incorporates extensive updates in fuel performance and material property models, including fuel thermal conductivity, pellet fragment relocation, fission gas release, fission gas swelling, and cladding creep and growth. Advances in thermal models are mainly in pellet fragment relocation, radial power distribution within the pellet, and the changes in fuel thermal conductivity due to changes in temperature, burnup and fuel porosity. The PAD5 thermal fission gas release model is a phenomenological model based on the irradiation dependence of the gas release from mechanistic processes for the diffusion of the fission gas generated in the fuel grains to the grain boundaries, formation of fission gas bubbles on the grain boundaries and release of the fission gas when these grain boundary bubbles inter-link. The PAD5 cladding creep model is predominantly a combination of the following mechanisms: thermal creep, irradiation induced creep, and irradiation enhanced creep. The fuel performance database used for the development, calibration and testing of the PAD5 code covers a broad range of both commercial irradiation data and test rod data and requires continuously additional data focusing on the latest development of the PAD5 code. Test programs are also included in the database. These data are checked and stored in a hierarchical database structure that supports the automation of model development and calibration. New data, once incorporated into the database, can be quickly evaluated with respect to key fuel and cladding performance models to confirm expected trends or to evaluate potential model improvements. This automated calibration system has been integrated with state-of-the-art optimization packages in DAKOTA Analysis Kit to provide for advanced statistical assessments and model coefficient optimization. Calibration results are automatically tabulated and plotted to provide easy assessment of trends or new behaviors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Oxidation behavior of Zry-4 in steam-air mixtures at high temperature

This study dealt with the oxidation behavior of Zry-4 nuclear fuel cladding under a severe nuclear reactor accident scenario occurring in a light-water reactor. Influence of the reaction extent on cladding mechanical properties was also treated. Zry-4 fuel cladding segments were exposed to steam atmosphere containing different amount of air in composition ranging from 0 to 100 vol. %. Exposure times covered both pre- and post-breakaway regimes. Metallographic observations along with microhardness testing were carried out to study the effect of air fraction on the material microstructure. Hydrogen pick-up was measured and residual mechanical properties were assessed employing Ring Compression Tests. The results show that the addition of air in steam can lead to more than 300 % increase of weight gain in case of ∼50 % or higher air fraction after the exposure of 60 min., namely, 'late post-breakaway regime'. Approximately three times thicker oxide scales were observed in such cases, indicating that most of the weight gain was due to the oxide layer increase. Nitride phase was preferentially observed close to the interface between oxide and metal layers. The α-Zr(O) sublayer thickness decreases with the increasing fraction of air in steam. Microhardness, measured within the prior β-phase region, slightly depends on the air fraction. Hydrogen uptake, on the other hand, depends strongly on the air fraction in steam. In the case of shorter exposure times, the effect of air addition in steam was suppressed. Eventually, specimen plastic strains drastically reduced in the late post-breakaway regime. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High burn-up spent nuclear fuel vibration integrity study - 15134

The Oak Ridge National Laboratory (ORNL) has developed the cyclic integrated reversible-bending fatigue tester (CIRFT) approach to successfully demonstrate the controllable fatigue fracture of high burnup (HBU) spent nuclear fuel (SNF) in a normal vibration mode. CIRFT enables examination of the underlying mechanisms of SNF system dynamic performance. Due to the inhomogeneous composite structure of the SNF system, the detailed mechanisms of pellet-pellet and pellet-clad interactions and the stress concentration effects at the pellet-pellet interface cannot be readily obtained from a CIRFT system measurement. Therefore, finite element analyses (FEAs) are being used to complement the experimental work by estimating values of local stresses and strains from the measured global moment-curvature. These results and their implications will be used for further investigation. Major findings of CIRFT on the HBU SNF are as follows: - The degree of bonding between pellets, as well as the bonding between pellets and clad in the SNF system plays an important role in the vibration performance of SNF. - Fuel structure contributes to SNF system stiffness. - There are significant variations in stress and curvature of SNF systems during vibration cycles resulting from segment pellet and clad interactions. - SNF failure initiates at the pellet-pellet interface region and appears to be spontaneous. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Description of a Dry Cask Simulator for Measuring Internal and External Thermal-Hydraulic Performance

The thermal performance of a commercial nuclear spent fuel dry storage cask is evaluated through detailed analytical modeling. These modeling efforts are performed by the vendor to demonstrate the performance as well as regulatory compliance and are independently verified by the Nuclear Regulatory Commission (NRC). The majority of commercial dry storage casks in use today are aboveground. Cooling of the assemblies located inside the sealed canister is achieved by air flowing in the bottom of the cask and exiting out the top. Carefully measured data sets generated from testing of full sized casks or smaller cask analogs are widely recognized as vital for validating design and performance models. Numerous studies have been previously conducted. Recent advances in dry storage cask designs have significantly increased the maximum thermal load allowed in a cask in part by increasing the efficiency of internal conduction pathways and by increasing the internal convection through greater canister helium pressure. These vertical, canistered cask systems rely on ventilation between the canister and the overpack to convect heat away from the canister to the environment for both above and belowground configurations. While several testing programs have been previously conducted, these earlier validation attempts did not capture the effects of elevated helium pressures or accurately portray the external convection of aboveground and belowground canistered dry cask systems. Thus the enhanced performance of modern dry storage casks cannot be fully validated using previous studies. The purpose of the investigation described in this report is to produce data sets for the validation of assumptions associated with the thermal-hydraulic simulation of modern dry cask storage systems. Of particular interest are the steady-state cladding temperatures and the effect of elevated helium pressures in sealed canisters in both above and belowground designs. An existing electrically heated but otherwise prototypic BWR Incoloy-clad test assembly will be deployed inside of a representative storage basket and cylindrical pressure vessel that will represent the canister. The arrangement of a single assembly with well-controlled boundary conditions should simplify interpretation of results. Various arrangements of outer concentric ducting will be used to mimic conditions for above and belowground storage configurations of vertical, dry cask systems with canisters. Radial and axial temperature profiles will be measured for a wide range of decay power and helium cask pressures. As of this writing, the apparatus is currently under construction at Sandia National Laboratories in Albuquerque, NM and is expected to be operational starting in April 2016. Pre-test CFD calculations have been performed using best available information. These calculations are being used to assist in test design but will need to be validated and potentially reevaluated. The planned testing will be adjusted to reflect as-built conditions and measured system limitations. Dimensional analyses indicate that the anticipated ranges of relevant dimensionless groups (Reynolds, Modified Rayleigh, and Nusselt numbers) bracket or closely approach prototypic values for both the aboveground and belowground configurations. While designed to match prototypic values, the expected test matrix will include values that exceed currently acceptable values for decay heat, internal helium pressure, and peak cladding temperatures in order to gain more insight into the underlying behavior of the system. (authors)

42 ENGINEERING↗

Corrosion Behavior of Pressurized Austenitic Tubes in Oxygen Containing PbBi at 550 deg. C

Pb-alloys as coolant media are foreseen in the lead fast reactor (LFR) and the MYRRHA reactor in Belgium. For both 15-15 Ti-stabilized steel (1.4970) should be used as fuel cladding material due to its low swelling at high doses. Its compatibility with lead (Pb) and lead-bismuth eutectic (LBE) has been studied in the past focusing on its behaviour at different temperature, oxygen concentrations and different flow velocities of the liquid metal. During operation swelling of the fuel by irradiation or fuel cracking will lead increase the stresses on the cladding wall, which can influence the corrosion behaviour. To perform tests in Pb/PbBi on cladding tubes under stress a new test device was constructed in which an internal pressure can be applied to tubes. First tests with pressurized 1.4970 tubes at 550 deg. C in PbBi with an oxygen concentration of 10{sup -6} wt% were conducted. (authors)

36 MATERIALS SCIENCE↗

Recovery and Recrystallization Behavior of Nb-Containing Fe-Cr-Al Alloys

Nuclear-grade wrought Fe-Cr-Al alloys are currently under development as promising accident-tolerant fuel cladding materials for light water reactors (LWRs) due to their superior oxidation and corrosion resistance in high temperature steam environments when compared with current commercial Zr-based alloys. Sufficient amounts of Cr and Al additions in Fe-Cr-Al alloys provide the improved surface protection effects at both the service temperature and elevated temperatures in the accident case scenario. Minor alloying additions (such as Nb in the current study) also promote the second-phase precipitates to strengthen the alloys; e.g. sub-micron size Fe{sub 2}Nb-type Laves phase precipitates are likely to disperse at both inter- and trans-granular in BCC-Fe matrix after applying proper heat treatments. In LWRs, a seamless tube product is required for the fuel cladding which typically has ∼ 4 m length with an outside diameter of ∼ 10 mm and a wall thickness of less than 0.5 mm, and it imposes considerable challenges for tube fabrication process (e.g. tube drawing) of Fe-Cr-Al alloys. Research has been performed to achieve a balance between high-temperature performance and tube fabricability in newly developed Fe-Cr-Al alloys. BCC-Fe materials with Cr and Al additions typically suffer from poor ductility because of relatively high ductile-brittle transition temperature. In this sense, the microstructural stability of refined grain or subgrain structure, even at high temperature, is critical to maintain the deformability of the alloys during tube fabrication process, as well as sufficient mechanical properties at service condition. In this study, the recovery and recrystallization behaviors of Nb-containing Fe-Cr-Al alloys are studied. A specific focus was to evaluate the stability of the subgrain structure of the deformed Fe-Cr-Al alloys, and seek optimized processing parameters for seamless tube fabrication. The present results clearly demonstrated that the Nb addition stabilizes the refined subgrain microstructures of Fe-Cr-Al alloys below 700 deg. C due to Laves phase precipitations along sub-boundaries when compared with the Nb-free alloys, while maintaining sufficient strengths needed for fuel cladding in LWRs. At the same time, the results also showed that Nb-containing alloys can be softened through suitable annealing to improve the processability of tube drawing process. Detailed characterization efforts of subgrains and Laves phase precipitates are currently in progress. Completion of this work will deepen the understanding of the recovery and recrystallized behavior of Nb-containing Fe-Cr-Al alloys and provide guidelines to tube drawing process in the alloys. (authors)

36 MATERIALS SCIENCE↗

Study on Modeling of Nuclear Fuel End Drop during a Hypothetical Accident

It is well known that shell elements have been used to model the cladding of single nuclear fuel pins. These have been used, for example, to analyze the response of a fuel assembly by assuming that all fuel pins in a fuel assembly deform in the same pattern. It is increasingly significant to model the entire fuel assembly in order to capture more realistically the behavior of each individual nuclear fuel during a hypothetical accident in a manner that can account for interactions among single pins. However, modeling each individual fuel pin in an entire fuel assembly using shell elements will result in models with large amount of elements and degrees of freedom that take correspondingly larger amount of computational times to execute. Therefore, modeling the nuclear fuel assembly with beam elements may become an option. This paper presents the results of a set of analysis with the LS-DYNA finite element software that investigated the differences and similarities of modeling nuclear fuel assemblies using either shell elements or beam elements. This study provides additional insights on the appropriateness of using beam element models of the fuel pins in the simulation of a hypothetical accident. In this study, two single pin models, a single pin model using shell elements and a single beam model using beam elements, are constructed to analyze end drop scenarios with the LS-DYNA code. Each model is then analyzed for a 19 ft end drop scenario (linear behavior) and 30 ft end drop scenario (non-linear behavior). Comparisons are made between the results obtained with the single pin shell model and with the single pin beam model to study the differences and similarities resulting from the two modeling approaches. In this study, a B and W 15x15 PWR fuel is analyzed for both 30 ft and 19 ft end hypothetical accident drops using both single pin finite element model with shell elements and beam elements for the fuel cladding. It is found that for the 19 ft end drop, the difference in the Max/Min total axial strains is about 12% between the two models. For the 30 ft end drop, the maximum total axial strains calculated with both models is similar, and a difference of about 12% is observed for the minimum total axial strains calculated by the two models. Advantages of the single pin shell model are that it permits consideration of internal pressures and may capture local buckling. Therefore, use of beam elements to model the fuel cladding needs to take into account the possible significance of local buckling and internal pressurization for the problem being analyzed. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Enhanced Thermal Conductivity UO{sub 2}-BeO and UO{sub 2}-SiC Fuels Behavior

Commercial light-water reactors currently use UO{sub 2} as a nuclear fuel, which has demonstrated several desirable characteristics. However, UO{sub 2} has a low thermal conductivity that leads to the development of a large temperature gradient across the fuel pellet. This temperature gradient contributes to limits in the operational performance of the reactor due to effects that include thermal stresses causing pellet cladding interaction and the release of fission product gases as demonstrated. These high fuel temperatures can be decreased and reactor performance improved by developing an enhanced thermal conductivity nuclear fuel. A high thermal conductivity nuclear fuel would decrease fuel temperatures and facilitate a reduction in pellet cladding interaction through lessening thermal stresses that result in fuel cracking, relocation, and swelling as described. Additionally, fission gas release would be decreased allowing for higher fuel burn-up, and the safety of the reactor would be improved with a faster thermal response and less stored energy in the fuel pins. A ceramic-ceramic composite nuclear fuel has an increased effective thermal conductivity due to adding a second compatible and high thermal conductivity ceramic to UO{sub 2}. SiC and BeO are two materials that demonstrate compatibility with UO{sub 2} and have a high thermal conductivity. In summary, the enhanced thermal conductivity UO{sub 2}-BeO and UO{sub 2}-SiC fuel performance has been modelled in a light water reactor, and a more complete and detailed understanding was achieved for enhanced thermal conductivity UO{sub 2}-BeO and UO{sub 2}-SiC fuels. BeO and SiC have high melting point, low neutron absorption, low thermal expansion coefficient and chemical compatibility with current UO{sub 2} fuels which makes them a suitable material for thermal conductivity enhancement. In our modeling and simulation work, the enhanced thermal conductivity nuclear fuel showed the capability of decreasing the fuel temperatures, increasing the gap total conductance, reducing the fission gas release, decreasing the gap/plenum pressure, lessening oxygen redistribution, and facilitating a reduction in pellet cladding interaction through lessening thermal stresses that result in fuel cracking, relocation, and swelling. The safety of the reactor operation would be then improved. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of PyC interlayer amorphization on the thermal conductivity of SiC/SiC composites - 18682

During the last two decades, silicon carbide based ceramic composites (SiC/SiC) have become a candidate material for nuclear fuel cladding, first for advanced nuclear systems, such as the GFR, and recently also as potential replacement material for nuclear fuel cladding in light water reactors. This work is contributing to the General Atomics/Westinghouse led CARAT project. This paper focuses on the consequences of the microstructural changes occurring at the pyrolytic (PyC) carbon interphases linking silicon carbide matrix and fibres in the composite. The experimental approach is two-fold: measurements of the thermal conductivity of short sections of prototype SiC/SiC cladding tubes deal with the macro-scale of the question, whereas the effects of radiation damage on the PyC interlayer are studied by energy filtered transmission electron microscopy (EFTEM) as well as spectrum imaging in STEM (ESI). The results from both parts of the experimental work are brought together in an effective medium model based on the work of Markworth and Youngblood et al. A detailed outlining of the radial heat flow experimental apparatus developed to this end has been presented at the 2016 ANS meeting in New Orleans. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In-pile measurements of fuel rod dimensional changes utilizing the test reactor loop pressure for motion - 359

Different types of materials are being considered for fuel, cladding, and structures in existing and advanced nuclear reactors. These materials can undergo significant dimensional changes during irradiation. Currently in the US, such changes are measured with the 'cook and look' method (i.e. repeatedly irradiating a specimen for a specified period of time, and then removing it from the reactor for evaluation) - which leads to costly and time consuming experiments. In addition, such techniques provide limited data, and handling may disturb the phenomena of interest. Therefore, in-pile detection of geometric changes is needed to understand real-time behavior during irradiation testing of fuels and materials in high flux US Material and Test Reactors (MTRs). The developmental results of an advanced Linear Variable Differential Transformer (LVDT)-based test rig capable of detecting real-time changes in diameter or length of fuel rods or other material samples during irradiation in US MTRs are presented. The LVDT is being developed at the Idaho National Laboratory (INL), and will provide experimenters with the capability to measure dimensional changes associated with fuel and clad swelling, pellet-clad interaction, and crud buildup. The LVDT design utilizes the MTR's loop pressure to drive the test specimen at a constant rate. This leads to a simplified construction which only requires three pressure boundary penetrations. Further, the LVDT pressure boundary is a leak tight hydraulic ram capable of actuating under low differential pressure (e.g. 1 psid), and is able to survive the high irradiation tests at Pressurized Water Reactor (PWR) conditions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Simulation of Proposed Heat Treatment Methods for the Sister Rods

The High Burnup Spent Fuel Data Project (the 'project'), sponsored by the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), is focused on experimentally evaluating the effects of long-term dry storage and transportation on high burnup (HBU) pressurized water reactor (PWR) fuel (>45 gigawatt days per metric ton uranium). The goals of the project are to provide confirmatory data for analytical model validation and potential improvement; to provide input to future dry storage cask design; to support license renewals and new licenses for Independent Spent Fuel Storage Installation facilities; and to support transportation licensing for high burnup used fuel. In support of these project goals, an instrumented TN-32B bolted-lid cask (the Research Project Cask or RPC) at the North Anna reactor site will be loaded with intact, HBU PWR fuel assemblies (Project Assemblies) having four different kinds of cladding: standard Zircaloy-4, low-tin Zircaloy-4, ZIRLO{sup R}, and M5{sup R}. In approximately ten years, the instrumented cask will be opened for inspection and several fuel rods from the Project Assemblies will be characterized. The project has also removed 25 'sister rods' from assemblies at North Anna: 9 directly from the project assemblies and 16 from similarly constructed and operated HBU assemblies. The 25 sister rods are all high burnup and cover the range of domestically-used cladding alloys. The 25 sister rods were shipped to Oak Ridge National Laboratory (ORNL) in early 2016 for detailed non-destructive examinations (NDE) followed by destructive examination (DE). Examination of the sister rods will provide a baseline for comparison with the cask rods and will allow for separate effects testing. Dry storage canister loading is completed under water in a designated area of the plant's spent fuel pool. In preparation for dry storage, the fuel assemblies and canister cavity must be drained and dried. Typically, the highest temperatures experienced by the fuel during dry storage are encountered either during drying or transfer of the canister to the storage pad; therefore, as a part of the sister rod testing these temperatures will be simulated in the lab to produce samples that are representative of the peak cladding temperature the fuel experiences either during drying, transfer, or storage. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗