Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffraction optics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Interstellar Optics

We discuss the effects of finite source size on the diffraction pattern produced by scattering in a thin screen, particularly as applied to radio-wave scattering, by density fluctuations in the interstellar plasma.

Interstellar Optics Scattering techniques telescop↗

Investigation of size dependent structural and optical properties of thin films of CdSe quantum dots

Research highlights: {yields} CdSe q-dots have been synthesized using simple chemical synthesis route. {yields} Thin film of CdSe quantum dots exhibited self-organized growth. {yields} Size dependent blue shift observed in the absorption edge of CdSe nanocrystallites. {yields} PL emission band corresponds to band edge luminescence and defect luminescence. {yields} Organized growth led to enhancement in luminescence yield of smaller size Q-dots. -- Abstract: Cadmium selenide (CdSe) quantum dots were grown on indium tin oxide substrate using wet chemical technique for possible application as light emitting devices. The structural, morphological and luminescence properties of the as deposited thin films of CdSe Q-dot have been investigated, using X-ray diffraction, transmission electron microscopy, atomic force microscopy and optical and luminescence spectroscopy. The quantum dots have been shown to deposit in an organized array on ITO/glass substrate. The as grown Q-dots exhibited size dependent blue shift in the absorption edge. The effect of quantum confinement also manifested as a blue shift of photoluminescence emission. It is shown that the nanocrystalline CdSe exhibits intense photoluminescence as compared to the large grained polycrystalline CdSe films.

36 MATERIALS SCIENCE↗

ZnTeO{sub 3} crystal growth by a modified Bridgman technique

Highlights: • ZnTeO{sub 3} single crystals were grown for the first time by a modified Bridgman method. • The growth is still possible in a system that lacks congruent melting. • A growth is best when melt is exposed to a steeper axial thermal gradient. • Optical and electrical properties were investigated for the grown crystals. - Abstract: Zinc Tellurite (ZnTeO{sub 3}) crystals were grown for the first time using a modified Bridgman method with a 2.5 kHz radio frequency (RF) furnace. Single crystal growth of ZnTeO{sub 3} was hindered by many complicating factors, such as the evaporation of TeO{sub 2} above 700 °C and the formation of more than one phase during crystal growth. While there were several successful runs that produced ZnTeO{sub 3} single crystals, it was found that large (≥10 cm{sup 3}) single ZnTeO{sub 3} crystals resulted when the crucible was exposed to a steeper vertical thermal gradient and when the temperature of the melt was raised to at least 860 °C. The results of powder X-ray diffraction (XRD) patterns were in accordance with the X-ray powder diffraction file (PDF) for ZnTeO{sub 3}. Some optical, electrical and structural properties of ZnTeO{sub 3} single crystals were reported in this paper.

36 MATERIALS SCIENCE↗

Cation ordering and physicochemical characterization of the quaternary diamond-like semiconductor Ag[subscript 2]CdGeS[subscript 4]

The quaternary diamond-like semiconductor, Ag2CdGeS4, was synthesized via high-temperature solid-state synthesis as well as structurally and physicochemically characterized. Single crystal X-ray diffraction provided a model for Ag2CdGeS4 in the orthorhombic, noncentrosymmetric space group Pna21 with a=13.7415(8) {angstrom}, b=8.0367(5) {angstrom} and c=6.5907(4) {angstrom}, in contrast to a previously published model in Pmn21 from the Rietveld analysis of laboratory X-ray powder diffraction data. The Pna21 space group is supported by the Rietveld analysis of synchrotron X-ray powder diffraction data. Differential thermal analysis suggests that Ag2CdGeS4 exists in two polymorphs. Optical diffuse reflectance UV/vis/NIR spectroscopy indicates that the orange compound is a semiconductor with a band gap of 2.32 eV. Optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and inductively coupled plasma optical emission spectroscopy were used to further characterize the material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and structural characterization of ferrous trioctahedral smectites: Implications for clay mineral genesis and detectability on Mars

Widespread detections of phyllosilicates in Noachian terrains on Mars imply a history of near-surface fluid-rock interaction. Ferrous trioctahedral smectites are thermodynamically predicted products of basalt weathering on early Mars, but to date only Fe 3+ -bearing dioctahedral smectites have been identified from orbital observations. In general, the physicochemical properties of ferrous smectites are poorly studied because they are susceptible to air oxidation. In this study, eight Fe 2+ -bearing smectites were synthesized from Fe 2+ -Mg-Al silicate gels at 200°C under anoxic conditions. Samples were characterized by inductively coupled plasma optical emission spectrometry, powder X-ray diffraction, Fe K-edge X-ray absorption spectroscopy (XAS), Mössbauer spectroscopy, and visible/near-infrared (VNIR) reflectance spectroscopy. The range of redox states was Fe 3+ /ΣFe = 0 to 0.06 ± 0.01 as determined by both XAS and, for short integration times, Mössbauer. The smectites have 060 distances (d (060) ) between 1.53 and 1.56 Å, indicating a trioctahedral structure. d (060) and XAS-derived interatomic Fe-(Fe,Mg,Al) distance scaled with Fe content. Smectite VNIR spectra feature OH/H 2 O absorption bands at 1.4 and 1.9 µm, (Fe 2+ ,Mg,Al) 3 -OH stretching bands near 1.4 µm, and Fe 2+ Fe 2+ Fe 2+ -OH, MgMgMg-OH, AlAl(Mg,Fe 2+ )-OH, and AlAl-OH combination bands at 2.36 µm, 2.32 µm 2.25 µm, and 2.20 µm, respectively. The spectra for ferrous saponites are distinct from those for dioctahedral ferric smectites, permitting their differentiation from orbital observations. X-ray diffraction patterns for synthetic high-Mg ferrosaponite and high-Mg ferrian saponite are both consistent with the Sheepbed saponite detected by the chemistry and mineralogy (CheMin) instrument at Gale Crater, Mars, suggesting that anoxic basalt alteration was a viable pathway for clay mineral formation on early Mars.

58 GEOSCIENCES↗

Overcoming the Intrinsic Limitations of Fast Charging Lithium‐Ion Batteries Using Integrated Acoustic Streaming

A lithium‐ion battery's maximum charge rate and energy density are intrinsically limited by the ion diffusion rate in the electrolyte. Most research focuses on materials science solutions to this problem, with gradual improvement over the years. A mechanical solution is proposed to integrate an MHz‐order frequency surface acoustic wave (SAW) device into an existing 1.8 Ah multilayered Li‐ion pouch cell to enhance the ion diffusion rate and the overall battery performance. Both the charging rate and cycling lifetime are improved from SAW. At a 6C (10 min) charge and C/3 discharge rate, typical of electric vehicle applications, integrating SAW into the Li‐ion cell doubles the energy density and maintains at least 72% of the battery's initial capacity after 2000 cycles. Moreover, using SAW quantifiably reduces battery degradation in these conditions as determined by optical imaging, scanning electron microscopy, X‐ray diffraction, and neutron diffraction. The use of SAW appears to offer a method to avoid undesirable Li metal plating on the graphite anode during charging, and leads to a much longer battery lifetime and good charge capacity, all despite rapid charging.

Huang, An↗

A Workflow for Accelerating Multimodal Data Collection for Electrodeposited Films

Abstract Future machine learning strategies for materials process optimization will likely replace human capital-intensive artisan research with autonomous and/or accelerated approaches. Such automation enables accelerated multimodal characterization that simultaneously minimizes human errors, lowers costs, enhances statistical sampling, and allows scientists to allocate their time to critical thinking instead of repetitive manual tasks. Previous acceleration efforts to synthesize and evaluate materials have often employed elaborate robotic self-driving laboratories or used specialized strategies that are difficult to generalize. Herein we describe an implemented workflow for accelerating the multimodal characterization of a combinatorial set of 915 electroplated Ni and Ni–Fe thin films resulting in a data cube with over 160,000 individual data files. Our acceleration strategies do not require manufacturing-scale resources and are thus amenable to typical materials research facilities in academic, government, or commercial laboratories. The workflow demonstrated the acceleration of six characterization modalities: optical microscopy, laser profilometry, X-ray diffraction, X-ray fluorescence, nanoindentation, and tribological (friction and wear) testing, each with speedup factors ranging from 13–46x. In addition, automated data upload to a repository using FAIR data principles was accelerated by 64x.

36 MATERIALS SCIENCE↗

A process optimization framework for laser direct energy deposition: Densification, microstructure, and mechanical properties of an Fe-Cr alloy

Laser Direct Energy Deposition (DED) is a metal additive manufacturing technique with the ability to fabricate large and complex parts through deposition of metal powders. However, achieving high-density parts and targeted build heights using DED can be challenging due to the large number of highly sensitive process variables. This work proposes a robust fabrication parameter optimization framework to generate process maps for primary parameters in DED, including laser power, scan speed, mass flow rate, hatch spacing, and layer height. Simple single-track experiments were utilized to map out the parameter space, and a combination of geometric criteria for hatch spacing and layer height were proposed to determine parameter sets that achieve both targeted build heights and mitigate porosity formation. Using this framework, specimens with >99 % density and consistent mechanical properties were successfully fabricated over a wide range of process parameters for an Fe-9wt.%Cr (Fe9Cr) alloy, a surrogate for radiation damage-resistant reduced activation ferritic/martensitic (RAFM) steels. Processing these materials using DED is of particular interest in the development of plasma facing components for nuclear fusion applications. The microstructure and mechanical properties of as-printed Fe9Cr were characterized using optical and electron microscopy, X-ray diffraction, and uniaxial tensile tests. As-printed Fe9Cr displayed ~25 % elongation and ultimate tensile strengths of up to 475 MPa which is comparable to similar wrought alloys. Finally, the proposed framework will allow for accelerated DED parameter optimization for novel alloy systems, as well as open the possibility for local microstructure control while simultaneously mitigating defect formation.

42 ENGINEERING↗

Investigation of UO 2 doped with Fe 2 O 3 sintered under a reducing atmosphere

Nuclear fuel produced with trace amounts of transition metal additives is of potential interest for introducing intentional signatures for accelerating nuclear forensics. In this work, we investigate the effects on microstructure, grain size, crystal structure, and stoichiometry when trace amounts of Fe in the form of Fe 2 O 3 are added to UO 2 . Sintering of compacts with different concentrations, from 250 to 3000 ppmw, was performed under a reducing atmosphere at 1773 K. The persistence of the taggant during the fuel fabrication process as well as its impact on grain size, crystal lattice, and first-neighbor chemistry was evaluated using inductively coupled plasma–optical emission spectroscopy, powder X-ray diffraction (pXRD), Raman spectroscopy, scanning electron microscopy–backscatter electron spectroscopy, energy dispersive spectroscopy, and thermogravimetric analysis. We observed that a negligible amount of Fe was lost during sintering. Our results indicate that the feedstock, Fe 2 O 3 transforms into Fe and FeO under the test sintering conditions. For all compositions, metallic Fe precipitate was found in grain boundaries as a secondary phase. In conclusion, the potential incorporation of ionic Fe into the UO 2 unit cell was determined by pXRD and Raman spectra.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Surface modification induced phase transformation and structure variation on the rapidly solidified recast layer of titanium

In this study, neodymium-doped yttrium orthovanadate (Nd:YVO{sub 4}) as a laser source with different scanning speeds was used on biomedical Ti surface. The microstructural and biological properties of laser-modified samples were investigated by means of optical microscope, electron microscope, X-ray diffraction, surface roughness instrument, contact angle and cell cytotoxicity assay. After laser modification, the rough volcano-like recast layer with micro-/nanoporous structure and wave-like recast layer with nanoporous structure were generated on the surfaces of laser-modified samples, respectively. It was also found out that, an α → (α + rutile-TiO{sub 2}) phase transition occurred on the recast layers of laser-modified samples. The Ti surface becomes hydrophilic at a high speed laser scanning. Moreover, the cell cytotoxicity assay demonstrated that laser-modified samples did not influence the cell adhesion and proliferation behaviors of osteoblast (MG-63) cell. The laser with 50 mm/s scanning speed induced formation of rough volcano-like recast layer accompanied with micro-/nanoporous structure, which can promote cell adhesion and proliferation of MG-63 cell on Ti surface. The results indicated that the laser treatment was a potential technology to enhance the biocompatibility for titanium. - Highlights: • Laser induced the formation of recast layer with micro-/nanoporous structure on Ti. • An α → (α + rutile-TiO{sub 2}) phase transition was observed within the recast layer. • The Ti surface becomes hydrophilic at a high speed laser scanning. • Laser-modified samples exhibit good biocompatibility to osteoblast (MG-63) cell.

36 MATERIALS SCIENCE↗

Strain induced grain boundary migration effects on grain growth of an austenitic stainless steel during static and metadynamic recrystallization

Static and metadynamic recrystallization of an AISI 304L austenitic stainless steel was investigated at 1100 °C and 10{sup −} {sup 2} s{sup −} {sup 1} strain rate. The kinetics of recrystallization was determined through double hit compression tests. Two strain levels were selected for the first compression hit: ε{sub f} = 0.15 for static recrystallization (SRX) and 0.25 for metadynamic recrystallization (MDRX). Both the as-deformed and the recrystallized microstructures were investigated through optical microscopy and electron back-scattered diffraction (EBSD) technique. During deformation, strain induced grain boundary migration appeared to be significant, producing a square-like grain boundary structure aligned along the directions of the maximum shear stresses in compression. EBSD analysis revealed to be as a fundamental technique that the dislocation density was distributed heterogeneously in the deformed grains. Grain growth driven by surface energy reduction was also investigated, finding that it was too slow to explain the experimental data. Based on microstructural results, it was concluded that saturation of the nucleation sites occurred in the first stages of recrystallization, while grain growth driven by strain induced grain boundary migration (SIGBM) dominated the subsequent stages. - Highlights: • Recrystallization behavior of a stainless steel was investigated at 1100 °C. • EBSD revealed that the dislocation density distribution was heterogeneous during deformation. • Saturation of nucleation sites occurred in the first stages of recrystallization. • Strain induced grain boundary migration (SIGBM) effects were significant. • Grain growth driven by SIGBM dominated the subsequent stages.

36 MATERIALS SCIENCE↗

Hydrogen induced cracking susceptibility of API 5L X70 pipeline steel in relation to microstructure and crystallographic texture developed after different thermomechanical treatments

Highlights: • crack propagated mainly along deformed-banded microstructure. • Lower failure strength manifested at pipeline steel surface compared to the mid-thickness. • Greater fraction of martensite/austenite constituents featured in specimen WG relative to specimen WH. • Early onset of cracking in specimen WH showed no preference to specific crystallographic orientation. • Multi-component inclusion particle was revealed along crack propagation path. - Abstract: Thermomechanical treatments offer an innovative means of controlling microstructure development and improving resistance to hydrogen induced cracking (HIC) in pipeline steel. This study was conducted on two X70 pipeline steels (labelled WG and WH) of the same chemical composition, but processed with different thermomechanical parameters. Specimen WG was hot rolled at a higher temperature range of 880–820 {sup °}C, while specimen WH was hot rolled between 830 and 760 {sup °}C before cooling at a rate of 25 {sup °}C/s. Early onset of HIC was observed in specimen WH after electrochemical hydrogen charging for 12 h in a solution of 0.2 M H{sub 2}SO{sub 4} and 3 g/l NH{sub 4}SCN, without any applied stress. Also, test pieces from the surface and mid-thickness layers of each pipeline steel were subjected to slow strain rate tensile (SSRT) test with in-situ hydrogen charging. Characterization techniques such as Optical Microscopy, Scanning Electron Microscopy, Electron Backscattered Diffraction and X-ray Diffraction were used to investigate the structure pipeline steel specimens. The role of inclusions on HIC was studied by Energy Dispersive X-ray Spectroscopy. Although the microstructure of both specimens were predominantly ferritic, more martensite/retained austenite (M/A) constituents featured in WG. Further crystallographic texture analysis indicates that grain orientation at the surfaces of both test specimens were similar with deviations towards <111> on the inverse pole figure (IPF); whereas, pole intensity at the mid-thickness deviated towards the <001> direction. Considering the increased fraction of banded-deformed grains with high stored energy, the lower HIC resistance of specimen WH in comparison to specimen WG was justified.

36 MATERIALS SCIENCE↗

Conversion of Nuclear Waste into Nuclear Waste Glass: Experimental Investigation and Mathematical Modeling

The melter feed, slurry, or calcine charged on the top of a pool of molten glass forms a floating layer of reacting material called the cold cap. Between the cold-cap top, which is covered with boiling slurry, and its bottom, where bubbles separate it from molten glass, the temperature changes by up to 1000 K. The processes that occur over this temperature interval within the cold cap include liberation of gases, conduction and consumption of heat, dissolution of quartz particles, formation and dissolution of intermediate crystalline phases, and generation of foam and gas cavities. These processes have been investigated using thermal analyses, optical and electronic microscopies, x-ray diffraction, as well as other techniques. Properties of the reacting feed, such as heat conductivity and density, were measured as functions of temperature. Investigating the structure of quenched cold caps produced in a laboratory-scale melter complemented the crucible studies. The cold cap consists of two main layers. The top layer contains solid particles dissolving in the glass-forming melt and open pores through which gases are escaping. The bottom layer contains bubbly melt or foam where bubbles coalesce into larger cavities that move sideways and release the gas to the atmosphere. The feed-to-glass conversion became sufficiently understood for representing the cold-cap processes via mathematical models. These models, which comprise heat transfer, mass transfer, and reaction kinetics models, have been developed with the final goal to relate feed parameters to the rate of glass melting.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Persistent dopants and phase segregation in organolead mixed-halide perovskites

Organolead mixed-halide perovskites such as CH 3 NH 3 PbX 3–a X' a (X, X' = I, Br, Cl) are interesting semiconductors because of their low cost, high photovoltaic power conversion efficiencies, enhanced moisture stability, and band gap tunability. Using a combination of optical absorption spectroscopy, powder X-ray diffraction (XRD), and, for the first time, 207 Pb solid state nuclear magnetic resonance (ssNMR), we probe the extent of alloying and phase segregation in these materials. Because 207 Pb ssNMR chemical shifts are highly sensitive to local coordination and electronic structure, and vary linearly with halogen electronegativity and band gap, this technique can provide the true chemical speciation and composition of organolead mixed-halide perovskites. We specifically investigate samples made by three different preparative methods: solution phase synthesis, thermal annealing, and solid phase synthesis. 207 Pb ssNMR reveals that nonstoichiometric dopants and semicrystalline phases are prevalent in samples made by solution phase synthesis. We show that these nanodomains are persistent after thermal annealing up to 200 °C. Further, a novel solid phase synthesis that starts from the parent, single-halide perovskites can suppress phase segregation but not the formation of dopants. Our observations are consistent with the presence of miscibility gaps and spontaneous spinodal decomposition of the mixed-halide perovskites at room temperature. This underscores how strongly different synthetic procedures impact the nanostructuring and composition of organolead halide perovskites. In conclusion, better optoelectronic properties and improved device stability and performance may be achieved through careful manipulation of the different phases and nanodomains present in these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recovery of Lithium from Geothermal Brine with Lithium–Aluminum Layered Double Hydroxide Chloride Sorbents

In this paper, we report a three-stage bench-scale column extraction process to selectively extract lithium chloride from geothermal brine. The goal of this research is to develop materials and processing technologies to improve the economics of lithium extraction and production from naturally occurring geothermal and other brines for energy storage applications. A novel sorbent, lithium aluminum layered double hydroxide chloride (LDH), is synthesized and characterized with X-ray powder diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometry (ICP-OES), and thermogravimetric analysis. Each cycle of the column extraction process consists of three steps: (1) loading the sorbent with lithium chloride from brine; (2) intermediate washing to remove unwanted ions; (3) final washing for unloading the lithium chloride ions. Our experimental analysis of eluate vs feed concentrations of Li and competing ions demonstrates that our optimized sorbents can achieve a recovery efficiency of ~91% and possess excellent Li apparent selectivity of 47.8 compared to Na ions and 212 compared to K ions, respectively in the brine. Finally, the present work demonstrates that LDH is an effective sorbent for selective extraction of lithium from brines, thus offering the possibility of effective application of lithium salts in lithium-ion batteries leading to a fundamental shift in the lithium supply chain.

25 ENERGY STORAGE↗

2-Aminoanthracene Crystallization in Its Compatible Polystyrene Block: RAFT Synthesis and Enhanced Charge Retention in Pentacene Transistor Gate Dielectrics

We synthesized polystyrene-block-polyanthrylaminomethylstyrene (PS-b-PAAS) via RAFT reaction and side chain modification where the PAAS block is 50%. By blending 2-aminoanthracene (2AA) with PS-b-PAAS, the co-aggregation behavior of the PAAS block and 2AA within the thin film was observed by optical microscopy (OM) and x-ray diffraction. At 5 and 10 wt% of 2AA within the thin film, OM results showed a clear morphological difference between PS matrix and PS-b-PAAS matrix. Differences in the 2AA excited state lifetime in these matrices were also established using transient absorption spectroscopy (TAS). Blends were used as gate dielectrics in pentacene transistors. We compared characteristic voltage (Vc, an indicator of threshold voltage) before and after charging of PS-b-PAAS blended with unsubstituted PS and both polymers individually blended with 2AA. For blended PS-b-PAAS and PS, as the concentration of PS-b-PAAS increases, the decreased Vc especially with negative charging of the pentacene indicated a larger concentration of charge carriers induced by the dielectric film. The charging experiments also revealed that the unique structure formed by the 2AA/PS-b-PAAS blend significantly affected the charge storage capability of the organic field-effect transistors (OFET). Furthermore, this work demonstrates the novel co-aggregation structure in the dielectrics, and furthermore its impact on charge storage capability in pentacene OFETs.

36 MATERIALS SCIENCE↗

Tuning the Electrocatalytic Oxygen Reduction Reaction Activity of PtCo Nanocrystals by Cobalt Concentration with Atomic-Scale Understanding

The development of a suitable catalyst for the oxygen reduction reaction (ORR) – the cathode reaction of proton exchange membrane fuel cells (PEMFC) – is necessary to push this technology towards widespread adoption. There have been substantial efforts to utilize bimetallic Pt-M alloys that adopt the ordered face-centered tetragonal (L10) phase in order to reduce the usage of precious metal, enhance the ORR performance, and improve catalyst stability. In this work, monodisperse Pt-Co nanocrystals (NCs) with well-defined size (4-5 nm) and cobalt composition (25-75 at%) were synthesized via colloidal synthesis. The transformation from the chemically disordered A1 (face-centered cubic, fcc) to the L10 phase was achieved via thermal annealing using both a conventional oven and a rapid thermal annealing process. The structure of the Pt-Co catalysts was characterized by a variety of techniques, including transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy in high-angle annular dark-field scanning transmission electron microscopy (STEM-EDS), small-angle X-ray scattering (SAXS), X-ray diffraction (XRD), and inductively coupled plasma-optical emission spectrometry (ICP-OES). The effects of annealing temperature on the composition-dependent degree of ordering, and subsequent effect on ORR activity is described. This work provides insights regarding the optimal spatial distribution of elements at the atomic level to achieve enhanced ORR activity and stability.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A mechanistic study of the dopant-induced breakdown in halide perovskites using solid state energy storage devices

Doping halide perovskites (HPs) with extrinsic species, such as alkali metal ions, plays a critical, albeit often elusive role in optimising optoelectronic devices. Here, we use solid state lithium ion battery inspired devices with a polyethylene oxide-based polymer electrolyte to dope HPs controllably with lithium ions. We perform a suite of operando material analysis techniques while dynamically varying Li doping concentrations. We determine and quantify three doping regimes; a safe regime, with doping concentrations of <10 20 cm –3 (2% Li : Pb mol%) in which the HP may be modified without detrimental effect to its structure; a minor decomposition regime, in which the HP is partially transformed but remains the dominant species; and a major decomposition regime in which the perovskite is superseded by new phases. We provide a mechanistic description of the processes mediating between each stage and find evidence for metallic Pb (0) , LiBr and LiPbBr 2 as final decomposition products. Combining results from synchrotron X-ray diffraction measurements with in situ photoluminescence and optical reflection microscopy studies, we distinguish the influences of free charge carriers and intercalated lithium independently. We find that the charge density is equally as important as the geometric considerations of the dopant species and thereby provide a quantitative framework upon which the future design of doped-perovskite energy devices should be based.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗