Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Ethyl 3-ethoxybutyrate, a new component of the transportation renewable fuel portfolio

The vast majority of energy that powers our global economy is from combustion of fossil fuels with the unintended consequence of increased deposition of carbon dioxide in the atmosphere and oceans. The scientific and technical challenges for the energy sector are to develop renewable energy sources that are sufficient to meet human energy consumption, are economically viable, and are ecologically sustainable. We investigated ethyl 3-ethoxybutyrate (EEB) as a fuel oxygenate in ultra low sulfur diesel (ULSD) with a bench-scale research engine and determined its economic potential as a renewable fuel with technoeconomic modeling using wastewater treatment plant biosolids as the feedstock for poly-3-hydroxyalkanoates (PHB), a bacterial storage polymer from which EEB can be synthesized. EEB blended well with ULSD, and cetane values of 10% and 20% v/v EEB-ULSD blends exceeded 40. A diesel internal combustion engine fueled with 5%, 10%, and 20% EEB-ULSD blends met or exceeded all tested transportation diesel fuel emissions criteria. Inedible organic feedstocks may be used to produce PHB; and thus, EEB might contribute to carbon reductions without compromising performance or air pollutant emissions. However, further research is needed to determine its role in the overall fuel portfolio. (C) 2015 Elsevier Ltd. All rights reserved.

09 BIOMASS FUELS↗

Fracture toughness measurement of ceramics with fuel pellet geometry

The crack initiation of nuclear fuel pellets, driven by extreme temperature gradients, is a critical factor impacting reactor performance. Although this fact is widely acknowledged, there is limited fracture toughness data for specimens with representative geometry and fabricated using relevant processing methods. Here, to address this, a new chevron-notched short-rod specimen configuration with diameter and length both equal to 10 mm, representative of a conventional fuel pellet and tested in tension, was developed in an attempt to validly measure Mode I fracture toughness, K Ic . Test calibration was carried out by testing polycrystalline ZrO 2 , SiC, and Si 3 N 4 ceramics fabricated with conventional fuel pellet geometry and known fracture toughnesses. The results suggest that the method described in this paper produces valid K Ic measurements using conventional ceramic fuel pellets.

Ceramics↗

MOOGLE: A Multi-Objective Optimization tool for three-dimensional nuclear fuel assembly design

MOOGLE is a new genetic algorithm methodology for the three-dimensional design of nuclear fuel assemblies. MOOGLE uses common fuel rod types as the decision variable to develop a suite of three-dimensional fuel assemblies to provide optimized solutions to the design problem. Pressurized Water Reactor (PWR) fuel assemblies were optimized using IFBA and gadolinium (Gd 2 O 3 ) as burnable poisons in order to compare how burnable poison choice affects optimization results. Boiling Water Reactor (BWR) fuel bundles were also optimized using three unique fuel rod palettes to study how the size of the design space affects optimization results. Burnable poison analysis showed that utilizing IFBA and Gd 2 O 3 as burnable poisons produced the best and widest range of optimized solutions. Further, BWR fuel bundle optimization results indicate that the inclusion of additional fuel rod types produced a wider solution space but did not improve optimization results for regions explored using fewer unique fuel rods. These tests demonstrate MOOGLE's ability to analyze the tradeoffs between the inclusion of different fuel elements and their effects on assembly performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Summary of DOD-Sponsored Research Performed at NASA Langley's Impact Dynamics Research Facility

The Impact Dynamics Research Facility (IDRF) is a 240-ft.-high gantry structure located at NASA Langley Research Center in Hampton, Virginia. The IDRF was originally built in the early 1960's for use as a Lunar Landing Research Facility. As such, the facility was configured to simulate the reduced gravitational environment of the Moon, allowing the Apollo astronauts to practice lunar landings under realistic conditions. In 1985, the IDRF was designated a National Historic Landmark based on its significant contributions to the Apollo Moon Landing Program. In the early 1970's the facility was converted into its current configuration as a full-scale crash test facility for light aircraft and rotorcraft. Since that time, the IDRF has been used to perform a wide variety of impact tests on full-scale aircraft, airframe components, and space vehicles in support of the General Aviation (GA) aircraft industry, the U.S. Department of Defense (DOD), the rotorcraft industry, and the NASA Space program. The objectives of this paper are twofold: to describe the IDRF facility and its unique capabilities for conducting structural impact testing, and to summarize the impact tests performed at the IDRF in support of the DOD. These tests cover a time period of roughly 2 1/2 decades, beginning in 1975 with the full-scale crash test of a CH-47 Chinook helicopter, and ending in 1999 with the external fuel system qualification test of a UH-60 Black Hawk helicopter. NASA officially closed the IDRF in September 2003; consequently, it is important to document the past contributions made in improved human survivability and impact tolerance through DOD-sponsored research performed at the IDRF.

Jackson, Karen E.↗

A Summary of DOD-Sponsored Research Performed at NASA Langley's Impact Dynamics Research Facility

The Impact Dynamics Research Facility (IDRF) is a 240-ft.-high gantry structure located at NASA Langley Research Center in Hampton, Virginia. The IDRF was originally built in the early 1960's for use as a Lunar Landing Research Facility. As such, the facility was configured to simulate the reduced gravitational environment of the Moon, allowing the Apollo astronauts to practice lunar landings under realistic conditions. In 1985, the IDRF was designated a National Historic Landmark based on its significant contributions to the Apollo Moon Landing Program. In the early 1970's the facility was converted into its current configuration as a full-scale crash test facility for light aircraft and rotorcraft. Since that time, the IDRF has been used to perform a wide variety of impact tests on full-scale aircraft, airframe components, and space vehicles in support of the General Aviation (GA) aircraft industry, the U.S. Department of Defense (DOD), the rotorcraft industry, and the NASA Space program. The objectives of this paper are twofold: to describe the IDRF facility and its unique capabilities for conducting structural impact testing, and to summarize the impact tests performed at the IDRF in support of the DOD. These tests cover a time period of roughly 2 1/2 decades, beginning in 1975 with the full-scale crash test of a CH-47 Chinook helicopter, and ending in 1999 with the external fuel system qualification test of a UH-60 Black Hawk helicopter. NASA officially closed the IDRF in September 2003; consequently, it is important to document the past contributions made in improved human survivability and impact tolerance through DOD-sponsored research performed at the IDRF.

Jackson, Karen E.↗

Control of Ionomer Distribution in Roll-to-Roll Coated Fuel Cell Catalyst Layers

Fuel cell catalyst layers are a complex mixture of catalyst particles and ion-conducting polymers. The performance of catalyst layers is highly dependent on microstructure, which must balance proton and electron conduction with gas transport. As fuel cells transition from the laboratory to industrial production for vehicles and other applications, there is a need to understand how manufacturing processes impact the microstructure and, ultimately, the performance of catalyst layers. In this work, we have focused on the roll-to-roll coating of catalyst layers for proton exchange membrane fuel cells. The catalyst layers are responsible for the electrochemical reactions that enable power production. In these devices the catalyst is commonly a Pt nanoparticle supported on porous carbon blacks. The ion conducting polymer, or ionomer, is typically a perfluorosulfonic acid. The most common being Nafion. To fabricate the catalyst layer, the catalyst particles are dispersed in an ink with the ionomer and cast to form the catalyst layer. Commonly, laboratory samples are prepared using spray coating or hand painting, which effectively coat many thin layers to achieve the desired catalyst layer thickness. This creates catalyst layers with uniform distributions of materials throughout the thickness of the full catalyst layer. In contrast, roll-to-roll methods, like slot die, gravure or screen printing, coat the catalyst layer as a single wet film. As the film dries, ink constituents are able to segregate, leading to a heterogeneous distribution of materials through the thickness of the layer. It is also known that the choice of solvent and drying rate can affect the morphology of the catalyst layer. Thus, there is a need to understand how ink formulation and the drying process influence the distribution of materials and catalyst layer morphology. Here, we have explored the influence of solvent and drying rate on morphology of roll-to-roll coated catalyst layers. We show the development of the Kelvin probe method as a rapid screening technique for qualitative analysis of ionomer distribution. We also utilize nano X-ray computed tomography to visualize electrode structure and to quantify particle-size and pore-size distributions, thickness-dependent ionomer distribution, tortuosity, and effective transport properties. We find that solvent has a strong influence on ionomer distribution, with less of an effect on porosity. Conversely, drying temperature has a strong influence on porosity, but less influence on ionomer distribution. Finally, we utilize in situ fuel cell performance testing and other advanced diagnostics to quantify the impact of catalyst layer properties on fuel cell performance and demonstrate that roll-to-roll coating is capable of coating high performance catalyst layers in multi-meter lengths.

14 SOLAR ENERGY↗

Minimizing Transuranic Waste Generated in Hot Cells at Oak Ridge National Laboratory Through Use of a Non-Destructive CO{sub 2} Pellet Cleaning System - 19577

Wastes generated in shielded hot cells containing materials contaminated with transuranic (TRU) waste present unique problems in waste disposal at Department of Energy (DOE) sites. Oak Ridge National Laboratory (ORNL) routinely processes materials contaminated with TRU waste from the High Flux Isotope Reactor (HFIR) and from other sources (both on and off-site) in their hot cell facilities, generating wastes that require eventual disposal. The waste streams generated by these processes are often high activity and exhibit high dose rates, driving them into the remote-handled (RH) category at the Waste Isolation Pilot Plant (WIPP). Reduction of the TRU waste footprint is desirable from a disposal cost perspective due to constraints with RH waste processing and a lack of space availability at the WIPP. Historically TRU waste generated at ORNL has been processed by the TRU Waste Processing Center (TWPC), which belongs to the Department of Energy's Office of Environmental Management (DOE-EM). Now that Oak Ridge legacy TRU waste is reaching its final stage, DOE-EM has turned over the mission of processing newly-generated TRU waste streams to the DOE Office of Science at ORNL. To reduce the volume of potential TRU waste occupying valuable space in the ORNL Hot Cells, a non-destructive CO{sub 2} pellet cleaning system will be used to capture particulate contaminants removed from the surfaces of waste inside the ORNL Non-Reactor Nuclear Facilities (NNFD) Hot Cells at the Irradiated Fuels Examination Laboratories (IFEL). The particulate will be segregated by particle size and captured for disposal later. This action will separate some of the TRU isotopes (particulate) from the larger waste volume (debris waste items), resulting in both lower waste disposal costs and reduced TRU waste volumes. This will be accomplished through a specialized cyclone separator. Secondary wastes are usually generated through other methods of decontamination, such as water jets and abrasive agents. These secondary wastes are absent with the CO{sub 2} pelletized system, due to sublimation of the dry ice upon impact. This is an important consideration with IFEL, a facility whose primary mission is to perform a series of R and D testing on nuclear fuel rods. Liquid is not a feasible method of decontamination as the IFEL's drains in the Hot Cells were plugged years ago due to Resource Conservation and Recovery Act (RCRA) regulations. Constraints at IFEL, such as criticality safety concerns with use of hydrogenous materials, are also alleviated with the non-destructive CO{sub 2} pellet cleaning system. These are a couple of the considerations why this method of decontamination is preferred. Due to concerns with oxidizers at WIPP grouting will be performed on the contaminated particulate produced during the trapping by the cyclone separation phase. This method will comply with mitigating oxidizing properties in TRU waste, required by the recently published Basis of Knowledge (BoK) document as part of Acceptable Knowledge (AK) by WIPP. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Method for Reducing the Temperature of Exhaust Manifolds

This report describes tests conducted at the Langley Memorial Aeronautical Laboratory on an "air-inducting" exhaust manifold for aircraft engines. The exhaust gases from each cylinder port are discharged into the throat of an exhaust pipe which has a frontal bellmouth. Cooling air is drawn into the pipe, where it surrounds and mixes with the exhaust gases. Temperatures of the manifold shell and of the exhaust gases were obtained in flight for both a conventional manifold and the air-inducting manifold. The air-inducting manifold was installed on an engine which was placed on a test stand. Different fuels were sprayed on and into the manifold to determine whether the use of this manifold reduced the fire hazard. The flight tests showed reductions in manifold temperatures of several hundred degrees, to values below the ignition point of aviation gasoline. On the test stand when the engine was run at idling speeds fuels sprayed into the manifold ignited. It is believed that at low engine speeds the fuel remained in the manifold long enough to become thoroughly heated, and was then ignited by the exhaust gas which had not mixed with cooling air. The use of the air-inducting exhaust manifold must reduce the fire hazard by virtue of its lower operating temperature, but it is not a completely satisfactory solution of the problem.

Schey, Oscar W↗

UN TRISO Compaction in SiC for FCM Fuel Irradiations

The U.S. Department of Energy Office of Nuclear Energy (DOE-NE) Advanced Fuels Campaign (AFC) is conducting research and development to elevate the technology readiness level of Fully Ceramic Microencapsulated (FCM) fuels, a candidate nuclear fuel with potentially enhanced accident tolerance due to very high fission product retention. One of the early activities in FY17 was to demonstrate production of FCM pellets with uranium nitride TRISO particles. This was carried out in preparation of the larger pellet production campaign in support of the upcoming irradiation testing of this fuel form at INL’s Advanced Test Reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance Testing of Moving Bed Gasifier Using Biomass and Waste Fuels to Generate Low-Cost Clean Hydrogen

Our need for hydrogen is growing as the world transitions toward a low-carbon future. Hydrogen provides long-term energy storage for grid stability in a solar- and wind-dominated power market and can be used to decarbonize other sectors. One promising process for generating low-cost hydrogen that produces net-negative carbon is to gasify biomass with a mixture of legacy coal wastes, waste plastics, and other wastes with carbon capture. Use of waste fuels lowers costs and diverts waste from landfills. EPRI is leading a project, funded by the U.S. Department of Energy, to conduct performance testing of modular, moving-bed gasification for the generation of low-cost, clean hydrogen from biomass mixed with legacy coal waste, waste plastic, and/or refuse derived fuels. The work scope includes preparation of multiple pellet feedstocks using biomass (both woody biomass and corn stover) with a mixture of legacy coal waste, plastic waste (wire insulation), and refuse-derived fuel (RDF). These pelletized feedstocks are being qualified based on performance testing of selected fuel blend compositions in updraft moving-bed gasifier located in Sardinia, Italy. Testing is being conducted to obtain relevant data to advance the modular design of the moving-bed gasification process, and successfully use these feedstocks to produce a high hydrogen content raw syngas that can be shifted to produce clean hydrogen. Testing results will be used to determine the effects of the various fuels on feedstock development, the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics), and impacts on gasifier operations.

08 HYDROGEN↗

Aluminum Clad Spent Nuclear Fuel Task 6: Surrogate Sample Preparation and Validation Experiment Test Plan

This document presents the experimental test plan for Task 6: Surrogate Preparation and Validation. Task 6 will produce and validate surrogate oxyhydroxide materials used in other experimental tasks within the larger Aluminum Clad Spent Nuclear Fuel Long Term Dry Storage Project. Task 6 includes both the preparation and characterization of surrogate oxyhydroxide materials as well as the analysis of oxide/oxyhydroxide layers on Savannah River Site Spent Nuclear Fuel Materials. This test plan provides experimental design details and the task’s overall quality assurance approach.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiation Environment of the Materials Test Station

Conceptual design of the proposed Materials Test Station (MTS) at the Los Alamos Neutron Science Center (LANSCE) is now complete. The principal mission is the irradiation testing of advanced fuels and materials for fast-spectrum nuclear reactor applications. The neutron spectrum in the fuel irradiation region of MTS is sufficiently close to that of fast reactor that MTS can match the fast reactor fuel centerline temperature and temperature profile across a fuel pellet. This is an important characteristic since temperature and temperature gradients drive many phenomena related to fuel performance, such as phase stability, stoichiometry, and fission product transport. The MTS irradiation environment is also suitable in many respects for fusion materials testing. In particular, the rate of helium production relative to atomic displacements at the peak flux position in MTS matches well that of fusion reactor first wall. Nuclear transmutation of the elemental composition of the fusion alloy EUROFER97 in MTS is similar to that expected in the first wall of a fusion reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and use of hydrogen-air torches in an altitude facility

A hydrogen-air ignition torch concept that had been used successfully in two rocket engine test facilities to consume excess hydrogen in their exhausters at atmospheric conditions was experimentally evaluated and developed in an altitude test facility at NASA Lewis Research Center. The idea was to use several of these torches in conjunction with hydrogen detectors and dilution air to prevent excess accumulation of unburned hydrogen or mixtures of hydrogen and air exceeding the sea-level lower flammability limit in the altitude facility exhaust system during hydrogen-fueled propulsion system tests. The torches were evaluated for a range of fuel-to-air ratios from 0.09 to 0.39 and for a range of exit diameters from 19/64 to 49/64 in. From the results of these tests a torch geometry and a fuel-to-air ratio were selected that produced a reasonably sized torch exhaust flame for consumption of unburned hydrogen at altitude pressures from sea level to 4 psia.

Lottig, Roy A.↗

Development and use of hydrogen-air torches in an altitude facility

A hydrogen-air ignition torch concept that had been used successfully in two rocket engine test facilities to consume excess hydrogen in their exhausters at atmospheric conditions was experimentally evaluated and developed in an altitude test facility at NASA Lewis Research Center. The idea was to use several of these torches in conjunction with hydrogen detectors and dilution air to prevent excess accumulation of unburned hydrogen or mixtures of hydrogen and air exceeding the sea-level lower flammability limit in the altitude facility exhaust system during hydrogen-fueled propulsion system tests. The torches were evaluated for a range of fuel-to-air ratios from 0.09 to 0.39 and for a range of exit diameters from 19/64 to 49/64 in. From the results of these tests a torch geometry and a fuel-to-air ratio were selected that produced a reasonably sized torch exhaust flame for consumption of unburned hydrogen at altitude pressures from sea level to 4 psia.

Lottig, Roy A.↗

Knowledge Management at the Fast Flux Test Facility

One of the goals of the Department of Energy’s Office of Nuclear Energy, initiated under the Fuel Cycle Research and Development Program (FCRD) and continued under the Advanced Reactor Concepts Program (ARC) is to preserve the knowledge that has been gained in the United States on Liquid Metal Reactors (LMRs) that could support the development of an environmentally and economically sound nuclear fuel cycle. The Fast Flux Test Facility (FFTF) is the most recent LMR to operate in the United States, from 1982 to 1992, and was designed as a fully instrumented test reactor with on-line, real time test control and performance monitoring of components and tests installed in the reactor. The 10 years of operation of the FFTF provided a very useful framework for testing the advances in LMR safety technology based on passive safety features that may be of increased importance to new designs after the events at Fukushima. Knowledge preservation at the FFTF is focused on the areas of design, construction, and startup of the reactor, as well as on preserving information obtained from 10 years of successful operating history and extensive irradiation testing of fuels and materials. In order to ensure protection of information at risk, the program to date has sequestered reports, files, tapes, and drawings to allow for secure retrieval. The FFTF knowledge management program includes a disciplined and orderly approach to respond to client’s requests for documents and data in order to minimize the search effort and ensure that future requests for this information can be readily accommodated.

data preservation↗

Flutter study of an advanced composite wing with external stores

A flutter test using a scaled model of an advanced composite wing for a Navy attack aircraft has been conducted in the NASA Langley Research Center Transonic Dynamics Tunnel. The model was a wall-mounted half-span wing with a semi-span of 6.63 ft. The wing had an aspect ratio of 5.31, taper ratio of 0.312, and quarter-chord sweep of 25 degrees. The model was supported in a manner that simulated the load path in the carry-through structure of the aircraft and the symmetric boundary condition at the fuselage centerline. The model was capable of carrying external stores from three pylon locations on the wing. Flutter tests were conducted for the wing with and without external stores. No flutter was encountered for the clean wing at test conditions which simulated the scaled airplane operating envelope. Flutter boundaries were obtained for several external store configurations. The flutter boundaries for the fuel tanks were nearly Mach number independent (occurring at constant dynamic pressure). To study the aerodynamic effect of the fuel tank stores, pencil stores (slender cylindrical rods) which had the same mass and pitch and yaw inertia as the fuel tanks were tested on the model. These pencil store configurations exhibited a transonic dip in the flutter dynamic pressure, indicating that the aerodynamic effect of the actual fuel tanks on flutter was significant. Several flutter analyses methods were used in an attempt to predict the flutter phenomenon exhibited during the wind-tunnel test. The analysis gave satisfactory predictions of flutter for the pencil store configurations, but unsatisfactory correlation for the actual fuel tank configurations.

Cole, Stanley R.↗