Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Stress Compensating Multilayers

We present in-situ stress measurement results for single and multilayer thin-films deposited by magnetron sputtering. In particular, we report on the influence of the material interfaces on the ensuing stress in both the transient and steady-state regimes of film growth. This behavior is used to determine the appropriate thicknesses of the constituent layers that will result in a net tensile stress in multilayers composed of various material combinations. These multilayers can then be used to compensate the compressive integrated stress in single and multilayer EUV and x-ray optical coatings. The use of multilayers to compensate the integrated stress might be advantageous because, unlike single layers of chromium, the roughness is not expected to increase with the total thickness of the multilayer. In this paper, we demonstrate the technique for W/Si and Mo/Si multilayers and discuss its application to other material combinations.

Multilayer↗

Effect of Pre- and Post-Coat Processing on the Fatigue Life of Coated Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can seriously degrade the life of the disk. Application of metallic coatings is one means of protecting disk alloys from this environmental attack. However, since LCF is sensitive to surface conditions, pre- and post-coat processing can have a significant effect on the LCF life of coated bars. Various pre-and post-coating conditions were examined with a Ni-45wt. Cr coating applied by High-power impulse magnetron sputtering (HiPiMS) to a Ni-based disk alloy. Initial pre-coat surface conditions examined a grit blasted surface. Later pre-coat surface treatments involved wet blasting, two shot peening levels (8N-200 and 16N-200) and a highly polished surface. Post-coat treatments involved two shot peening levels (4N-100 and 16N-200) and a post-coat diffusion anneal in high purity Ar or a low PO2 environment to encourage chromia scale formation. Half of the coated and uncoated bars were LCF tested at 760C without further environmental exposure to evaluate the pre- and post-coat treatments. The second half of samples were either oxidized for 500 hours at 760C in air, hot corroded for 50 hours at 760C in air using a Na2SO4-MgSO4 salt, or subjected to both exposures. Results of the LCF testing and post-test characterization of the various coatings will be presented and future research directions discussed.

LCF Life↗

Supermirror Design for Hard X-Ray Telescopes On-Board Hitomi (ASTROH)

We designed depth-graded multilayers, so-called supermirrors, with platinum/carbon (Pt/C) layer pairs for the Hard X-Ray Telescope (HXT) that was on-board the sixth Japanese X-Ray Astronomy Satellite Hitomi (ASTRO-H). The HXT has multinested thin foil optics, and the grazing angles of the x-ray mirrors are 0.07 to 0.27 deg. Supermirrors for HXTs are designed to provide a broad energy response (up to 80 keV) for astronomical requests. Under practical boundary conditions, we establish a block method applying empirical rules to maximize the integrated reflectivity. We fabricated Pt/C supermirrors using a DC magnetron sputtering system. The reflectivity of the mirrors was measured in a synchrotron radiation facility, SPring-8. We describe the design method for the supermirrors and our results.

Tamura, Keisuke↗

Reflective Coatings for the Future X-Ray Mirror Substrates

We present the development of the reflective coating by magnetron sputtering deposition onto precisely-fabricated thin X-ray mirrors. Our goal is to remove distortion induced by the coating and then keep their surface pro les. We first addressed the uniform coating to minimize the distortion by introducing a mask to control the spatial distribution of the coating thickness. The uniformity was finally achieved within 1%. We next tried a platinum single-layer coating on a glass substrate with a dimension of 200 mm 125 mm. The distortion caused by the frontside coating with a thickness of 320 A was found to be at most 1 m, smaller than the previous results obtained from the non-uniform coating. We then carried out the platinum coating with the same amount of the thickness on the backside surface of the glass substrate. The surface pro le of the glass substrate was fully recovered, indicating that the residual stress was successfully balanced by the backside coating. Furthermore, we tried to an iridium single-layer coating with a thickness of 150 Aon the silicon mirrors. The frontside coating caused the degradation of the imaging quality by 7:5 arcsec in half-power width. However, the backside coating with the same amount of the thickness reduced this degradation to be 3:4 arcsec. Finally, an additional backside coating with a thickness of 100 A and the annealing to relax the residual stress were found to eliminate the distortion completely; the final degradation of the imaging quality was only 0:4 arcsec.

Mori, Hideyuki↗

LCF Life of As-Deposited and Annealed NiCr-Y Coatings for Oxidation and Hot Corrosion Protection of Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can seriously degrade the life of the disk. Application of metallic coatings is one means of protecting disk alloys from this environmental attack. However, the presence of a metallic coating can degrade the LCF life of a disk alloy. Therefore, coatings must be designed which are not only resistant to oxidation and corrosion attack, but do not significantly degrade the LCF life of the alloy.Three different NiCr-Y coating compositions (29, 35.5, 44 wt.% Cr, all with 0.1 wt.% Y) were applied at two thicknesses by Plasma Enhanced Magnetron Sputtering (PEMS) to two similar Ni-based disk alloys. One Ni-35.5Cr-0.1Y coating also received a thin ZrO2 overcoat. The coated samples were also given a short thermal anneal in a low PO2 environment to encourage bonding of the coating and substrate as well as initiating formation of a chromia scale. Without further environmental exposure, the LCF life of coated and uncoated samples was evaluated at 760°C in air. The LCF lifetime of all coated samples was less than that of uncoated samples. The LCF life scaled with the Cr content and the high-Cr, thin coating showed the highest LCF life. Pre and post-test characterization of the various coatings, including identification of crack initiation sites, will be presented and the effect of the coating on the LCF life discussed.

low cycle fatigue↗

LCF Life of NiCr-Y Coated Disk Alloys After Shot Peening, Oxidation and Hot Corrosion

In a prior companion study (Ref. 1), three different Ni-Cr coating compositions (29, 35.5, 45 wt% Cr) were applied at two thicknesses by Plasma Enhanced Magnetron Sputtering (PEMS) to two similar Ni-based disk alloys. One coating also received a thin ZrO2 overcoat. The low cycle fatigue (LCF) life of each coating was determined at 760 °C and was less than that of the uncoated specimens. In this followon effort, shot peening was examined as a means to improve the as-deposited coating morphology as well as impart a residual compressive stress in the near-surface region. After evaluating the effect of the shot peening on the LCF life, the effectiveness of the shot-peened coating in protecting the disk alloy from oxidation and hot corrosion attack was evaluated. This evaluation was accomplished by exposing coated and shot-peened specimens to 500 h of oxidation followed by 50 h of hot corrosion, both at 760 °C in air. These exposed specimens were then tested in fatigue and compared to similarly treated and exposed uncoated specimens. For all cases, shot peening improved the LCF life of the coated specimens. More specifically, the highest Cr coating showed the best LCF life of the coated specimens after shot peening, as well as after the environmental exposures. Characterization of the coatings after shot peening, oxidation, hot corrosion and LCF testing is presented and discussed.

James A Nesbitt↗

Optical Constants Determination of Samarium Holmium and Erbium in the 1.5-850 eV Spectral Range using a Transmittance Method

The optical constants {beta} and {sigma} of the complex refractive index {tilde n} = 1 - {delta} + i{beta} of Sm, Ho, and Er were obtained in the 1.5-850 eV energy range using a transmittance method. Thin films of Sm, Ho, and Dr were deposited by magnetron sputtering, and transmittance was measured using synchrotron radiation using a high vacuum condition. All films were directly coated on Si photodiodes, which were used as coating substrates, as well as photon detectors. Si was used as capping layer while a thin W layer was used as barrier against interface diffusion between Si and the highly reactive rare earth elements. The constants {beta} were extracted from transmittance results, and the constants {sigma} were calculated based on measured {beta} values using the Kramers-Kronig formalism. Small deficiencies determined from the present data using the partial sum rules were partially attributed to the sputtered film densities that could be slightly lower than the bulk values.

36 MATERIALS SCIENCE↗

Residual Stress Characterization of Al/SiC Nanoscale Multilayers using X-ray

Nanolayered composites are used in a variety of applications such as wear resistant coatings, thermal barrier coatings, optical and magnetic thin films, and biological coatings. Residual stresses produced in these materials during processing play an important role in controlling their microstructure and properties. In this paper, we have studied the residual stresses in model metal-ceramic Al/SiC nanoscale multilayers produced by physical vapor deposition (magnetron sputtering). X-ray synchrotron radiation was used to measure stresses in the multilayers using the sin{sup 2} {psi} technique. The stresses were evaluated as a function of layer thicknesses of Al and SiC and also as a function of the number of layers. The stress state of Al in the multilayer was largely compressive, compared to single layer Al stresses. This is attributed to a peening mechanism due to bombardment of the Al layers by SiC and Ar neutrals during deposition. The stress evolution was numerically modeled by a simplified peening process to qualitatively explain the Al thickness-dependent residual stresses.

36 MATERIALS SCIENCE↗

Role of interfaces i nthe design of ultra-high strength, radiation damage tolerant nanocomposites

The combination of high strength and high radiation damage tolerance in nanolaminate composites can be achieved when the individual layers in these composites are only a few nanometers thick and contain special interfaces that act both as obstacles to slip, as well as sinks for radiation-induced defects. The morphological and phase stabilities and strength and ductility of these nano-composites under ion irradiation are explored as a function of layer thickness, temperature and interface structure. Magnetron sputtered metallic multilayers such as Cu-Nb and V-Ag with a range of individual layer thickness from approximately 2 nm to 50 nm and the corresponding 1000 nm thick single layer films were implanted with helium ions at room temperature. Cross-sectional Transmission Electron Microscopy (TEM) was used to measure the distribution of helium bubbles and correlated with the helium concentration profile measured vis ion beam analysis techniques to obtain the helium concentration at which bubbles are detected in TEM. It was found that in multilayers the minimum helium concentration to form bubbles (approximately I nm in size) that are easily resolved in through-focus TEM imaging was several atomic %, orders of magnitude higher than that in single layer metal films. This observation is consistent with an increased solubility of helium at interfaces that is predicted by atomistic modeling of the atomic structures of fcc-bcc interfaces. At helium concentrations as high as 7 at.%, a uniform distribution of I nm diameter bubbles results in negligible irradiation hardening and loss of deformability in multi layers with layer thicknesses of a few nanometers. The control of atomic structures of interfaces to produce high helium solubility at interfaces is crucial in the design of nano-composite materials that are radiation damage tolerant. Reduced radiation damage also leads to a reduction in the irradiation hardening, particularly at layer thickness of approximately 5 run and below. The strategies for design of radiation-tolerant structural materials based on the knowledge gained from this work will be discussed.

36 MATERIALS SCIENCE↗

Ion Generator

Andre Anders, at Lawrence Berkeley National Laboratory, speaks about magnetron sputtering, a technology used for thin films.

74 ATOMIC AND MOLECULAR PHYSICS↗

Analysis of Bulk and Thin Film Model Samples Intended for Investigating the Strain Sensitivity of Niobium-Tin

Bulk samples and thin films were fabricated and characterized to determine their suitability for studying the effect of composition and morphology on strain sensitivity. Heat capacity and resistivity data are used to determine the critical temperature distribution. It is found that all bulk samples contain stoichiometric Nb{sub 3}Sn regardless of their nominal Nb to Sn ratio. Furthermore, in bulk samples with Cu additions, a bi-modal distribution of stoichiometric and off-stoichiometric Nb-Sn is found. Thus the nominally off-stoichiometric bulk samples require additional homogenization steps to yield homogeneous off-stoichiometric samples. A binary magnetron-sputtered thin film has the intended off-stoichiometric Nb-Sn phase with a mid-point critical temperature of 16.3 K. This type of sample is a suitable candidate for investigating the strain sensitivity of A15 Nb{sub 1-{beta}}Sn{sub {beta}}, with 0.18 < {beta} < 0.25. The strain sensitivity of Nb-Sn as a function of composition and morphology is important for an in-depth understanding of the strain sensitivity of composite Nb{sub 3}Sn wires.

43 PARTICLE ACCELERATORS↗

Understanding the Mechanism of Solvent-Mediated Adhesion of Vacuum Deposited Au and Pt Thin Films onto PMMA Substrates

The adhesion of 100 nm thick electron-beam deposited Au and Pt and magnetron sputtered Au thin films onto poly(methyl methacrylate) (PMMA) substrates can be significantly enhanced to over 90% adhesion by either spin-casting or vapor-exposure to hydrohalocarbon solvents prior to metal deposition compared to samples that are either cleaned in isopropyl alcohol or pre-treated with a remote O2 plasma. X-ray photoelectron spectroscopy (XPS) and evolved gas Fourier transform infrared spectroscopy (EGA-FTIR) reveal the presence of residual halogenated solvent molecules at the PMMA surface which chemically activates the surface to produce a stable chemical interaction between the noble metal film and the PMMA. Density functional theory (DFT) calculations show that the halogenated solvent molecules preferentially form a Lewis acid-base adduct with the oxygen atoms in the ester group in PMMA which is consistent with the measured enthalpy of desorption of chloroform (CHCl3) on PMMA determined by EGA-FTIR to be 36 kJ mol-1. The DFT model also supports the experimentally observed change in the high resolution XPS O 1s peak at 533.77 eV after metallization attributed to a change in the local bonding environment of the bridging O in the PMMA ester group. DFT also predicts that the deposited metal atom (M) inserts into the C-X bond where X is the halogen atom on either CHCl3 or bromoform (CHBr3) to form a O M X interaction that is observed by a M-X bond in the high resolution XPS Cl 2p3/2 peak at 198.03 eV and Br 3p3/2 peak at 182.06 eV. A range of solvents with differing polarities for PMMA pre-treatment have been used and it is proposed that non-complexing solvents result in significant metal adhesion improvement. The Gutmann acceptor number can be used to predict the effectiveness of solvent treatment for noble metal adhesion. A model is proposed in which the bond energy of the C-X bond of the solvent must be sufficiently low so that the C-X bond can be cleaved to form the M-X bond. Supporting this model, a negative control of vapor phase exposure to fluoroform (CHF3) is shown to have no effect on noble metal adhesion due to the higher bond dissociation energy of the C-F bond compared to the C-Cl and C-Br bond energy. The surface activation of vapor-phase exposed PMMA surfaces is technologically significant for the fabrication of polymer microdevices requiring Au or Pt metallization.

Mo, Alan K↗

Extremely fast reaction kinetics of Mo3Sb7 thin films as anodes for Li- and Na-ion batteries

Mo3Sb7 thin films prepared by magnetron sputtering are evaluated as an anode material for Li- and Na-ion batteries. The as deposited films are amorphous and composed of small agglomerated domains with an overall Sb/Mo ratio of 2.34 that is almost identical to the ratio measured for the starting powder and the expected nominal ratio of 2.33. When cycled with Li and Na, the films show large storage capacities of around 430 and 330 mAh g-1, respectively, with good capacity retention. In addition, micron thick films retain large capacities of about 310 and 280 mAh g-1 at very high rates of 100 and 30 C-rate currents for Li and Na, respectively. The XRD study of the changes in the structure of the electrode material reveals that Li3Sb forms at full discharge whereas the electrode at full charge is amorphous. For the reaction with Na, the electrode material remains amorphous. Analysis of the surface chemistry characterized by XPS suggests the formation of an inorganic layer (LiF, LixPOyFz) covered by organic products (carbonates, esters, ethers) in the case of Li and the formation of an organic layer only (carbonates) in the case of Na. The electrode surface is visible at full charge for Na, thereby indicating that the SEI layer is thinner when cycling with Na compared to that with Li. Overall, the results highlight the very good potential of Mo3Sb7 as an anode for Li- and Na-ion batteries.

Baggetto, Loic↗

Fabrication and characterization of high energy density lithium-rich nickel manganese cobalt oxide cathode thin films

This paper reports a method to prepare Li-rich NMC (Li1.2Mn0.55Ni0.15Co0.1O2) thin film cathodes for Li-ion batteries using magnetron sputtering and post-annealing in O2. The use of thin films with no binder and conductive additives enables to study in detail the surface reaction chemistry upon cycling as well as the microstructural changes in the bulk. We show that it is essential to control the deposition pressure to obtain the expected layered(R-3m)-layered(C2/m) structure, thus providing large reversible capacities up to 270 mAh g-1 and voltage profiles close to those expected. This is substantiated by TEM/SAED results showing that the films consist of a layered structure with trigonal symmetry in which Li/TM ordering is achieved. The study of various XPS core levels determines that the surface is comprised of Mn4+, Co3+ and Ni2+ cations inside an O2- framework. The losses mechanisms are studied during long cycling. After 184 cycles, the microstructure does not reveal the presence of Li/TM ordering, which supports that Li2MnO3 conversion is irreversible. In addition, we characterize that the surface chemistry evolves significantly upon cycling. The surface of cycled discharged electrodes is mostly made of inorganic species (LiF, Lix POy Fz , LixPFy), along with small amounts of organic species with C-O and O-C=O groups such as PEO, LiOR and LiCO2R. Moreover, the results support that Ni and Co migrate into the bulk whereas Mn is enriched at the surface. In the case of Mn, the reduction of Mn4+ into Mn3+ is clearly evidenced, as expected from the activation of Li2MnO3 domains.

Baggetto, Loic↗

Growth and Characterization of Multi-Layer NbTiN Films

Significant theoretical interest has stimulated efforts to grow and characterize thin multi-layer superconductor/insulator/superconductor structures for their potential capability of supporting otherwise inaccessible surface magnetic fields in SRF cavities. The technological challenges include realization of high quality superconductors with sharp, clean, transition to high quality dielectric materials and back to superconductor, with careful thickness control of each layer. Choosing NbTiN as the first candidate material, we have developed the tools and techniques that produce such SIS film structures and have begun their characterization. Using DC magnetron sputtering and HiPIMS, NbTiN and AlN can be deposited with nominal superconducting and dielectric parameters. Hc1 enhancement is observed for NbTiN layers with a Tc of 16.9 K for a thickness less than 150 nm. The optimization of the thickness of each type of layer to reach optimum SRF performance is underway. This talk describes this work and the rf performance characteristics observed to date.

Valente-Feliciano, Anne-Marie↗

Progress with Nb Hipims Films on 1.3 GHz Cu Cavities

In recent years, efforts have been invested to leverage the different processes involved in energetic condensation to tailor Nb film growth in sequential steps. The resulting Nb/Cu films display high quality material properties and show promise of high RF performance. The lessons learned are now applied to 1.3 GHz Nb on Cu cavity deposition via high power impulse magnetron sputtering (HiPIMS). RF performance is measured at different temperatures. Particular attention is given to the effect of cooldown and sensitivity to external applied magnetic fields. The results are evaluated in light of the Nb film material and superconducting properties measured with various microscopy and magnetometry techniques in order to better understand the contributing factors to the residual and flux induced surface resistances. This contribution presents the insights gained in exploiting energetic condensation as a path towards RF Q-slope mitigation for Nb/Cu films, correlating film material characteristics with RF performance.

Burton, Matthew C.↗

Thin Films Development For Superconducting RF Applications

Significant progress has recently been made in the development of niobium (Nb) films for Superconducting RF (SRF) applications using energetic condensation of ions extracted from plasma generated by Electron Cyclotron Resonance. Nb films with RRR comparable to bulk values are readily produced on both metallic and insulating substrates. The controlled incoming ion energy enables a number of processes such as desorption of adsorbed species, enhanced mobility of surface atoms and sub-implantation of impinging ions, thus producing improved film structures at lower process temperatures. Particular attention is given to the nucleation conditions to create a favorable template for growing the final surface exposed to SRF fields. The influence of the deposition energy is investigated with the characterization of the film surface, structure, superconducting properties and RF performance. With a similar approach, High Power Impulse Magnetron Sputtering (HiPIMS) is investigated for the development of multilayer SIS (superconductor-insulator-superconductor) structures which have the theoretical prospect to reach RF performance beyond bulk Nb. This paper presents results on the correlation of the surface and material characteristics with the superconducting properties and RF surface impedance for Nb and multilayered NbTiN-based SIS films produced on a variety of substrates.

Zhao, X.↗

Characterization of NbTiN Thin Film Structures

Approaching the bulk Nb material RF performance limits has urged development of alternative superconducting materials for superconducting radio frequency (SRF) accelerator cavities for further performance enhancement. A promising theory has predicted that thin film structures of superconductor-insulator-superconductor (SIS) [1] can delay magnetic flux penetration in accelerator cavities to higher fields. A candidate superconductor for the SIS structures is NbTiN. A few key aspects of SIS structures development are high quality individual layers, sharp interfaces and optimum thickness for first flux penetration (Hfp) delay. High quality monocrystalline NbTiN films are deposited by reactive DC magnetron sputtering. In a parallel development, interface quality was assessed by depositing bilayers of 3 nm NbTiN with ~1 nm AlN repeated up to 16 times with no increase in roughness of the structure. The stacked layers form a metamaterial, which could exhibit Tc greater than bulk NbTiN [2]. This contribution presents the characterization of the surface, material and superconductivity of NbTiN with concentration on the Hfp enhancement for 200 to 5 nm films and multilayer nanostructures.

Beverstock, David↗