Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Ironsand (Titanomagnetite-Titanohematite): Chemistry, Magnetic Properties and Direct Applications for Wireless Power Transfer

Ironsand is an abundant and inexpensive magnetic mineral resource. However, the magnetic properties of unprocessed ironsand are often inadequate for any practical applications. In this work, the applicability of ironsand for use as a component in a soft magnetic composite for large-scale inductive power transfer applications was investigated. After magnetic separation, the chemical, structural and magnetic properties of ironsand sourced from different locations were compared. Differences observed in the DC magnetic properties were consistent with changes in the chemical compositions obtained from X-ray Absorption Near-Edge Spectroscopy (XANES), which suggests varying the titanohematite to titanomagnetite content. Increased content in titanomagnetite and magnetic permeability correlated well with the total Fe content in the materials. The best-performing ironsand with the highest permeability and lowest core losses was used alongside Mn,Zn-Ferrite particles (ranging from ~100 μm to 2 mm) to fabricate toroid cores with varying magnetic material loading. It was shown that ironsand can be used to replace up to 15 wt.% of the magnetic materials with minimal impact on the composite magnetic performance, thus reducing the cost. Ironsand was also used as a supporting material in a single-rail wireless power transfer system, effectively increasing the power transfer, demonstrating potential applications to reduce flux leakage.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A STATISTICAL STUDY OF FLARE PRODUCTIVITY ASSOCIATED WITH SUNSPOT PROPERTIES IN DIFFERENT MAGNETIC TYPES OF ACTIVE REGIONS

It is often believed that intense flares preferentially originate from the large-size active regions (ARs) with strong magnetic fields and complex magnetic configurations. This work investigates the dependence of flare activity on the AR properties and clarifies the influence of AR magnetic parameters on the flare productivity, based on two data sets of daily sunspot and flare information as well as the GOES soft X-ray measurements and HMI vector magnetograms. By considering the evolution of magnetic complexity, we find that flare behaviors are quite different in the short- and long-lived complex ARs and the ARs with more complex magnetic configurations are likely to host more impulsive and intense flares. Furthermore, we investigate several magnetic quantities and perform the two-sample Kolmogorov–Smirnov test to examine the similarity/difference between two populations in different types of ARs. Our results demonstrate that the total source field strength on the photosphere has a good correlation with the flare activity in complex ARs. It is noted that intense flares tend to occur at the regions of strong source field in combination with an intermediate field-weighted shear angle. This result implies that the magnetic free energy provided by a complex AR could be high enough to trigger a flare eruption even with a moderate magnetic shear on the photosphere. We thus suggest that the magnetic free energy represented by the source field rather than the photospheric magnetic complexity is a better quantity to characterize the flare productivity of an AR, especially for the occurrence of intense flares.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2019

Preparation and Characterization of NdFeB/PrCo{sub 5} Nanocomposite Magnetic Materials

We first developed NdFeB/PrCo{sub 5} nanocomposite magnetic material by high-energy ball milling, and the influence of the different contents of PrCo{sub 5} on the magnetic properties of NdFeB was studied by means of XRD, DSC, and VSM. The results showed that compared with single-phase NdFeB permanent-magnet material, NdFeB/PrCo{sub 5} nanocomposite magnetic material has superior magnetic properties. When the content of PrCo{sub 5} is 10% and the time of ball milling is 10 h, the magnetic properties for NdFeB/PrCo{sub 5} nanocomposite magnetic material is best: coercivity is 13.2 kOe, which increased by 14.8% over pure NdFeB phase. Remanent magnetization is 96.31 emu/g and the saturation magnetization is 132.29 emu/g. The remanence ratio is 0.728.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Correlating melting and collapse of charge ordering with magnetic transitions in La{sub 0.5-x}Pr{sub x}Ca{sub 0.5}MnO{sub 3}

Highlights: • Concept of normalized magnetization is introduced to explain relative magnetic transitions. • Coexistence of two magnetic modes is correlated with the magnetic transitions and MIT. • Field induced melting and collapse of charge ordered antiferromagnetic (CO-AFM) state into ferromagnetic (FM) state is conferred. - Abstract: The magnetic properties of polycrystalline La{sub 0.5-x}Pr{sub x}Ca{sub 0.5}MnO{sub 3} material are investigated at different temperatures. The existence of magnetically diverse phases associated with various relaxation modes and their modulation with temperature and doping is analyzed. La{sub 0.5}Ca{sub 0.5}MnO{sub 3} exhibited field induced melting and collapse of charge ordered antiferromagnetic (CO-AFM) phase into ferromagnetic (FM) state. This phenomenon results in lowering of Neel’s temperature (T{sub N}) along with changes in the slope of magnetic moment with temperature. Using normalized M(T) curves, the variation and interplay of charge ordered temperature (T{sub CO}), Curie temperature (T{sub C}) and T{sub N} is conferred. The coexistence of two magnetic modes is explained as major ingredient for the magnetic transitions as well as metal to insulator transition (MIT); where melting and collapse of charge ordering is conversed as basic feature in these Praseodymium (Pr) doped La{sub 0.5}Ca{sub 0.5}MnO{sub 3} materials.

36 MATERIALS SCIENCE↗
DOE OSTI2016

JLAB's Super High Momentum Spectrometer's Superconducting Q1 Magnet

Abstract- The commissioning and test results of a super ferric, superconducting, quadrupole magnet, constructed by Scientific Magnetics Inc. for Thomas Jefferson National Accelerator Facility (TJNAF also known as JLAB) will be presented. The quadrupole magnet, named Q1, is the first focusing element in the Super High Momentum Spectrometer (SHMS). The SHMS, located within JLAB's experimental Hall C, consists of all superconducting magnets in a dQQQD configuration and is part of the JLAB's 12 Gev upgrade. Here "d" refers to the small horizontal bend dipole, "Q" stands for focusing quadrupole magnets and "D" is the vertical bending, momentum-selecting dipole magnet. Characterization of the magnet's cryogenic heat loads and magnetic field quality will be presented along with descriptions of the magnet's control system, power supply, and quench detection system.

Superconductor Magnets, Detector Magnets, Cold Iro↗
DOE OSTI2024

Design of B1pF-A Large Aperture Dipole Magnet for EIC

The design of interaction region (IR) magnets for the Electron Ion Collider (EIC), demands tight boundary conditions on the magnet design given by the high field requirements and the proximity of electron and hadron beams within a common yoke and resultant crosstalk. Here, this article discusses the electromagnetic design of the superconducting collared magnet B1pF. The magnet will be built as the prototype for several collared magnets (dipoles and quadrupoles) for the hadron beam in the forward direction of the IR. The magnet design is based on a single layer coil with an inner diameter of 300 mm over a slot length of 3 m. The magnet produces an integral field of 10.34 T.m at a current of 11.9 kA to produce a nominal field of about 3.96 T at its center. Given by the common Rutherford cable parameters, the magnet will be used as a baseline for optimization of all the collared magnets. The article further discusses yoke optimizations, quench analysis, coil end design and efforts on fine tuning of field quality.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

MAGNETIC NULL POINTS IN KINETIC SIMULATIONS OF SPACE PLASMAS

We present a systematic attempt to study magnetic null points and the associated magnetic energy conversion in kinetic particle-in-cell simulations of various plasma configurations. We address three-dimensional simulations performed with the semi-implicit kinetic electromagnetic code iPic3D in different setups: variations of a Harris current sheet, dipolar and quadrupolar magnetospheres interacting with the solar wind, and a relaxing turbulent configuration with multiple null points. Spiral nulls are more likely created in space plasmas: in all our simulations except lunar magnetic anomaly (LMA) and quadrupolar mini-magnetosphere the number of spiral nulls prevails over the number of radial nulls by a factor of 3–9. We show that often magnetic nulls do not indicate the regions of intensive energy dissipation. Energy dissipation events caused by topological bifurcations at radial nulls are rather rare and short-lived. The so-called X-lines formed by the radial nulls in the Harris current sheet and LMA simulations are rather stable and do not exhibit any energy dissipation. Energy dissipation is more powerful in the vicinity of spiral nulls enclosed by magnetic flux ropes with strong currents at their axes (their cross sections resemble 2D magnetic islands). These null lines reminiscent of Z-pinches efficiently dissipate magnetic energy due to secondary instabilities such as the two-stream or kinking instability, accompanied by changes in magnetic topology. Current enhancements accompanied by spiral nulls may signal magnetic energy conversion sites in the observational data.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Nonvolatile Magnetoelectric Switching of Magnetic Tunnel Junctions with Dipole Interaction

The magnetoelectric effect is technologically appealing because of its ability to manipulate magnetism using an electric field rather than magnetic field or current, thus providing a promising solution for the development of energy-efficient spintronics. Although 180° magnetization switching is vital to spintronic devices, the achievement of 180° magnetization switching via magnetoelectric coupling is still a fundamental challenge. Here, in this work, voltage-driven full resistance switching of a magnetic tunnel junction (MTJ) with dipole interaction on a ferroelectric substrate through switchable parallel/antiparallel magnetization alignment is demonstrated. Parallel magnetization alignment along the y direction is obtained under a bias magnetic field. By rotating the magnetic easy axis via strain-mediated magnetoelectric coupling, the parallel magnetizations in the MTJ reorient to the x axis with opposite paths because of dipole interaction, thus resulting in antiparallel alignment. Moreover, this voltage switching of MTJs is nonvolatile owing to variations in dipole interaction and can be well understood via phase field simulations. The results provide an avenue to realize electrical switching of MTJs and are significant for exploring energy-efficient spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

3D Quantum Anomalous Hall Effect in Magnetic Topological Insulator Trilayers of Hundred‐Nanometer Thickness

Magnetic topological states refer to a class of exotic phases in magnetic materials with the non-trivial topological property determined by magnetic spin configurations. An example of such states is the quantum anomalous Hall (QAH) state, which is a zero magnetic field manifestation of the quantum Hall effect. Current research in this direction focuses on QAH insulators with a thickness of less than 10 nm. Here, molecular beam epitaxy (MBE) is employed to synthesize magnetic TI trilayers with a thickness of up to ≈106 nm. It is found that these samples exhibit well-quantized Hall resistance and vanishing longitudinal resistance at zero magnetic field. By varying the magnetic dopants, gate voltages, temperature, and external magnetic fields, the properties of these thick QAH insulators are examined and the robustness of the 3D QAH effect is demonstrated. The realization of the well-quantized 3D QAH effect indicates that the nonchiral side surface states of the thick magnetic TI trilayers are gapped and thus do not affect the QAH quantization. The 3D QAH insulators of hundred-nanometer thickness provide a promising platform for the exploration of fundamental physics, including axion physics and image magnetic monopole, and the advancement of electronic and spintronic devices to circumvent Moore's law.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The magnetic effects on the energetic landscape of Fe-Cu alloy: A model Hamiltonian approach

Using ab initio calculations and the magnetic cluster expansion formula, a model with the magnetic effects on the energetic landscape of Fe–Cu was developed. The (partially) disordered local moment picture and Monte Carlo simulation method were combined to study the magnetically disordering effects on the thermodynamic properties in Fe–Cu alloys. The simulation results show nonlinear enhancements of Fe magnetism with increasing Cu concentration under varying magnetic ordering/disordering states, and the nonlinearity of the enhancement is more significant under the ferromagnetic state. It is also found that magnetism has subtle effects on the clustering of Cu because both the substitutional and binding energies could be affected but in different ways depending on the magnetic states. The results suggest that the alloying-induced enhancement of the Fe magnetism is a fundamental feature of Fe–Cu, which introduces difference on the concentration dependence of mixing, depending on the magnetic ordering/disordering states. In conjunction with the concentration dependence of short-range ordering, the enhancement of Fe magnetism also strongly affects the Curie temperatures in Fe–Cu.

Ab Initio Calculations, Fe-Cu, ultrasonic backscat↗
DOE OSTI2020

63,65 Cu NMR study of the magnetically ordered state of the multiferroic CuFeO 2

In this work, field-swept 63,65 Cu NMR spectra under magnetic fields up to 8.3 T at a constant NMR frequency and temperatures T < 12 K on a single crystalline sample of multiferroic CuFeO 2 were measured and analyzed. When the magnetic field is applied along the c axis, a nearly zero internal magnetic field at the Cu site in magnetic ordered state was observed. This is explained by the perfect cancellation of the internal fields produced by the 6 nearest neighbor Fe 3+ ( S = 5/2) ions, revealing the magnetic structure to be a collinear four-sublattice structure. On the other hand, when the magnetic field is applied along the ab plane, we observed a finite internal field at the Cu sites, which is due to the canting of the Fe moments. Strong change in the NMR signal intensity is observed around 7–8 T, corresponding to the magnetic phase transition from the collinear magnetic to ferroelectric incommensurate states. The ratio of the two magnetic phases significantly depends on the history of the change in the external magnetic field and the temperature of the sample. The details of history dependence of the ratio were discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Internal defect detection and characterization of samarium-cobalt sintered magnets by ultrasonic testing technique

Excessive quantities of samarium-cobalt (Sm-Co) magnet material are being scrapped needlessly due to a lack of understanding of inhomogeneity distribution and unacceptable internal defects. If there is a way to identify, locate, characterize and when needed separate the defective portions of magnet material, utilization can be increased and product quality improved. Further, the magnets’ magnetic and mechanical performance can be improved by reducing the occurrence of internal defects. This paper reports on a cost-effective and efficient nondestructive evaluation method based on an ultrasonic testing (UT) technique applied for detecting and characterizing internal defects in Sm-Co sintered magnets. Applying the UT technique will allow users to comprehensively analyze internal defects, such as inclusions, porosity, microcracks, and other structural irregularities, check for homogeneity and anomalous regions and give the locations of these internal anomalies and defects within the Sm-Co sintered magnets. The UT technique can also be applied to other rare-earth permanent magnets, such as sintered or die-upset neodymium-iron-boron (Nd-Fe-B) magnets. The UT technique can effectively guide quality control and acceptable product selection, in addition to optimizing the magnet alloy design and production processes. Therefore, it can facilitate the improvement of magnet manufacturing efficiency and machinability, reduce scrap, prolong service life, increase the use of what would be post-production waste, and enhance product reuse and recycling at end-of-life disposition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Geometric control of magnetic domain morphology in electrodeposited Ni rich NiPt mesoscopic wires

In this paper, we study the electrodeposited Ni—Pt magnetic wires, exploring the mechanisms by which changes in geometry and composition influence the local magnetic structure. The samples were prepared by electrodeposition, their elemental composition was analyzed by energy dispersive X-ray spectroscopy, and phase analysis was carried out by an X-ray diffraction measurement. Magnetic force microscopy measurements, and magnetic force microscopy measurements in magnetic field were carried out to study the domain morphology of the prepared samples. Magnetization characteristics were measured via vibrating sample magnetometry mode of a superconducting quantum interference device. Here, the results were analyzed and compared with micromagnetic simulations. It is shown that a strong perpendicular magnetic anisotropy is responsible for the characteristic checkerboard-like surface magnetization patterns, which can be tuned by geometrical constriction and Ni content. Understanding these relationships provides insights into the design of magnetic materials with tailored properties for advanced applications, like magnetic sensors.

Binary alloy↗
DOE OSTI2016

Magnetic adsorbent constructed from the loading of amino functionalized Fe{sub 3}O{sub 4} on coordination complex modified polyoxometalates nanoparticle and its tetracycline adsorption removal property study

A magnetic polyoxometalates based adsorbent has been synthesized successfully through the loading of amino functionalized Fe{sub 3}O{sub 4} (NH{sub 2}-Fe{sub 3}O{sub 4}) on nanoparticle of a coordination complex modified polyoxometalates (CC/POMNP). FTIR illustrate there exist intense hydrogen bonds between NH{sub 2}-Fe{sub 3}O{sub 4} and CC/POMNP, which keep the stability of this adsorbent. At room temperature, this adsorbent exhibits ferromagnetic character with saturation magnetization of 8.19 emu g{sup −1}, which provides prerequisite for fast magnetic separation. Water treatment experiment illustrates this POM based magnetic adsorbent exhibits high adsorption capacity on tetracycline. The adsorption process can be described well with Temkin model, which illustrates the interaction between adsorbent and tetracycline plays the dominated role in tetracycline removal. The rapid, high efficient tetracycline adsorption ability suggests this POM based magnetic adsorbent exhibits promising prospect in medical and agriculture waste water purification. A magnetic polyoxometalates based adsorbent, which exhibits excellent tetracycline adsorption removal property has been synthesized through the loading of NH{sub 2}-Fe{sub 3}O{sub 4} on coordination complex modified polyoxometalates - Graphical abstract: A magnetic polyoxometalates based adsorbent, which exhibits excellent tetracycline adsorption removal property has been synthesized through the loading of NH{sub 2}-Fe{sub 3}O{sub 4} on coordination complex modified polyoxometalate. Display Omitted - Highlights: • A POM based magnetic adsorbent was fabricated through the loading of NH{sub 2}-Fe{sub 3}O{sub 4} on POM nanoparticle. • This adsorbent possesses excellent tetracycline adsorption property. • Saturation magnetization value of this adsorbent is 8.19 emug−1, which is enough for magnetic separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

A state of the art current-septum dipole magnet

Here, the acceleration process of charged particle beams often requires the use of few acceleration stages to provide the beam with the desired energy. The extraction of the beam from one acceleration stage and the injection to the next, both require a special type of magnet which comes under the name septum magnet. Such a magnet generates a strong field in one region and a very low field in another region with the two regions separated by a very thin material (septum). The septum thickness of such a magnet should be as thin as possible to reduce the strength of other devices, like kickers, which are involved in the extraction or injection processes. A thin septum is also advantageous during the slow beam extraction process to reduce the beam losses at the septum. One of the methods which in theory can generate very large differences in field strength in adjacent field regions separated by a thin septum, is the use of two thin parallel current sheets of infinite dimensions. In practice we use other devices that can approximate such an abrupt change of the magnetic field within the septum thickness. In this paper we describe such a device, the DC current septum, we present results from the study of its electromagnetic properties, and we discuss a method to minimize the magnetic field in the region which requires a very small magnetic field. We also provide some results from the experimental measurements of the magnetic field generated by the D6 current septum magnet which is installed in the experimental beam line of the NASA’s Space Radiation Laboratory (NSRL) facility [1],[2] at Brookhaven National Laboratory (BNL). This septum magnet is part of the beam’s extraction system from the AGS-Booster into the NSRL beam line for material and biological studies.

43 PARTICLE ACCELERATORS↗
DOE OSTI2015

Conventional magnetic superconductors

We discuss several classes of conventional magnetic superconductors including the ternary rhodium borides and molybdenum chalcogenides (or Chevrel phases), and the quaternary nickel-borocarbides. These materials exhibit some exotic phenomena related to the interplay between superconductivity and long-range magnetic order including: the coexistence of superconductivity and antiferromagnetic order; reentrant and double reentrant superconductivity, magnetic field induced superconductivity, and the formation of a sinusoidally-modulated magnetic state that coexists with superconductivity. We introduce the article with a discussion of the binary and pseudobinary superconducting materials containing magnetic impurities which at best exhibit short-range “glassy” magnetic order. Early experiments on these materials led to the idea of a magnetic exchange interaction between the localized spins of magnetic impurity ions and the spins of the conduction electrons which plays an important role in understanding conventional magnetic superconductors. Furthermore, these advances provide a natural foundation for investigating unconventional superconductivity in heavy-fermion compounds, cuprates, and other classes of materials in which superconductivity coexists with, or is in proximity to, a magnetically-ordered phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Recycling of additively printed rare-earth bonded magnets

Here, we describe an efficient and environmentally benign method of recycling of additive printed Nd-Fe-B polymer bonded magnets. Rapid pulverization of bonded magnets into composite powder containing Nd-Fe-B particles and polymer binder was achieved by milling at cryogenic temperatures. The recycled bonded magnets fabricated by warm compaction of ground cryomilled coarse composite powders and nylon particles showed improved magnetic properties and density. Remanent magnetization and saturation magnetization increased by 4% and 6.5% respectively, due to enhanced density while coercivity and energy product were retained from the original additive printed bonded magnets. This work presents a facile method that enables the direct reuse of end-of-life bonded magnets for remaking new bonded magnets. In addition to magnetic properties, mechanical properties comparable to commercial products have been achieved. This research advances efforts to ensure sustainability in critical materials by forming close loop supply chain.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tuning Magnetic Symmetry and Properties in the Olivine Series Li 1–x Fe x Mn 1–x PO 4 through Selective Delithiation

In this work, we present the first in-depth study of the nuclear and magnetic structures of the fully lithiated LiFe x Mn 1–x PO 4 solid solutions as well as the partially delithiated Li 1– xFe x Mn 1–x PO 4 series using neutron powder diffraction. By using a weak oxidizing solution that only oxidizes Fe 2+ , we find that lithium can be removed from these olivines in a stepwise manner. Representational analysis was performed on the observed magnetic reflections and found that the lithiated solid solutions order in the magnetic space group Pnma', which is identical to triphylite (LiFePO 4 ). We report that, even when removing 20% of the lithium from the hcp lattice, the magnetic structure changes and multiple magnetic contributions are needed to fully encompass the observed magnetic order. We find that the partially delithiated x = 0.2 and 0.3 have a magnetic structure P2 1 '/n11, and when x surpasses 0.3, the magnetic structure changes to P2 1 2 1 2 1 . We give a detailed report on the effect of delithiation on magnetic order, bond distances/angles, and the super- and supersuperexchange interactions in the material. The symmetries of the magnetic order of these solid solutions are then discussed with regard to their potential as ferrotoroidic candidates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗