Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optical microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Electron Microscopy and Elemental Composition of the Near-Surface Layer of Electron-Irradiated LiF Crystals

Electron microscopy and optical vibrational spectroscopy techniques have been used to study Li nanoparticles formed on the cleaved surface of lithium fluoride (LiF) crystals irradiated by 4-MeV electron beam to a total fluence of 5 × 10{sup 16} cm{sup –2}. It is suggested that ionization accompanying this intense irradiation leads to radiolysis of the target and removal of fluorine from interblock boundaries, where lithium cations are collected and mutually oriented to form microwires. This functional surface may be of practical interest.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Gamma and x-ray irradiation effects on different Ge and Ge/F doped optical fibers

We performed electron paramagnetic resonance (EPR) measurements on γ and X ray irradiated Ge doped and Ge/F co-doped optical fibers. We considered three different drawing conditions (speed and tension), and for each type of drawing, we studied Ge and Ge/F doped samples having Ge doping level above 4% by weight. The EPR data recorded for the γ ray irradiated fibers confirm that all the samples exhibit a very close radiation response regardless of the drawing conditions corresponding to values used for the production of specialty fibers. Furthermore, as for the X irradiated materials, in the γ ray irradiated F co-doped fibers, we observed that the Ge(1) and the Ge(2) defects generation is unchanged, whereas it was enhanced for the E'Ge. In the various fibers, the comparison of the γ and X-ray induced concentrations of these kinds of Ge related defects indicates that the two irradiations induce similar effects regardless of the different employed dose rates and sources. Confocal microscopy luminescence results show that the starting content of the Germanium Lone Pair Center (GLPC) is neither strongly affected by the Ge content nor by the drawing conditions, and we consider the similarity of the GLPC content as key factor in determining many of the above reported similarities.

36 MATERIALS SCIENCE↗

Ultrafast imaging of transient electronic plasmas produced in conditions of femtosecond waveguide writing in dielectrics

Femtosecond laser-induced plasmas in bulk dielectrics are imaged under waveguide writing conditions, for different polarizations, pulse durations, and processing depths, and their temporal evolution is measured using ultrafast pump-probe microscopy. The irradiation beam profile is elliptically shaped yielding a disklike focal volume. We demonstrate for doped phosphate glass that increasing the pulse duration improves the spatial distribution of deposited energy by minimizing beam filamentation and prefocal depletion effects. As a consequence, energy deposition in the desired volume is greatly enhanced. Our results identify key parameters for optimizing femtosecond laser processing of dielectrics and different strategies to minimize energy loss channels.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

MICROSCOPIC DYNAMICS AT THE GLASS TRANSITION: INSIGHTS FROM SOFT COLLOIDAL DISPERSIONS

We investigate the microscopic dynamics of compressible colloidal particles as function of concentration through dynamic light scattering and confocal microscopy experiments. In analogy with hard sphere (HS) colloidal systems, we find that the particles display liquid, supercooled liquid or glassy dynamics, depending on volume fraction. In the present case, however caging effects are observed for particle volume fractions higher than one, i.e. when the particles are compressed. We find that heterogeneous dynamics, described by a non Gaussian distribution of the displacements, play a major role in the supercooled liquid in proximity of the relaxation time.

36 MATERIALS SCIENCE↗

Simple imaging for the diamond anvil cell: Applications to hard-to-reach places

The employment of high-pressure gases as a pressure-transmitting medium, sample, or reactant for diamond anvil cell experiments is widespread. As a pressure transmitter, high-pressure gases are crucial to forming quasi-hydrostatic compression atmospheres for samples inside the uniaxially driven cell. We describe an optical design for forming high-resolution images of the gasket and sample chamber of the diamond anvil cell under high gas pressures in a gas loading apparatus. Our design is simple, is of low-cost, and may be easily adapted to suit gas loading apparatus of any design, as well as other common hard-to-reach environments in diamond anvil cell experiments, i.e., those with large stand-off distances, such as cryostats.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-resolution in-situ characterization of the surface evolution of a polycrystalline NiTi SMA-alloy under pseudoelastic deformation

The current study addresses the relation between grain orientations, local strain concentrations and resulting topographical changes in NiTi on the meso- and microscale by means of a comprehensive experimental in-situ approach, involving electron backscatter diffraction, confocal laser scanning microscopy and digital image correlation. The findings presented herein clearly show that this approach is capable of identifying the relationships between the microstructural features and phase transformation-induced topographical evolutions, which govern defect formation in thin protective coatings. - Research Highlights: {yields} High local strain gradients are observed between highly misoriented grains. {yields} Pronounced surface alterations emerged across these boundaries. {yields} Roughness evolution induced highly localized strains in the vicinity of grain boundaries. {yields} EBSD at {epsilon} = 5.5% proved the existence of intergranular constraints.

36 MATERIALS SCIENCE↗

Effects of germanium and nitrogen incorporation on crystallization of N-doped Ge{sub 2+x}Sb{sub 2}Te{sub 5} (x = 0,1) thin films for phase-change memory

The phase-change behavior and microstructure changes of N-doped Ge{sub 3}Sb{sub 2}Te{sub 5}[N-GST(3/2/5)] and Ge{sub 2}Sb{sub 2}Te{sub 5}[GST(2/2/5)] films during the phase transition from an amorphous to a crystalline phase were studied using in situ temperature-dependent sheet resistance measurements, X-ray diffraction, and transmission electron microscopy. The optical band gaps of N-GST(3/2/5) films are higher than that of GST(2/2/5) film in both the amorphous and face-centered-cubic (fcc) phases. Ge nitride formation by X-ray photoelectron spectroscopy analysis increased the optical band gap and suppressed crystalline grain growth, resulting in an increase in the crystallization temperature and resistance in the fcc phase. As a result, the Ge- and N-doped GST(2/2/5) composite films can be considered as a promising material for phase-change memory application because of improved thermal stability and reduced power consumption.

36 MATERIALS SCIENCE↗

Direct electrochemical generation of supercooled sulfur microdroplets well below their melting temperature

Significance Since the first discovery of supercooling in 1724, the study of supercooled matter has been mainly limited to varying temperature or pressure. Here we demonstrate an electrochemical approach to generate and observe supercooled sulfur. Our methodology combines dark-field microscopy, a transparent electrochemical cell, and a fast camera to visualize the process at single microdroplet with millisecond time resolution. This platform may open up opportunities for studying supercooled liquids as the droplets approach either homogeneous nucleation to the crystalline state or enter into the glass transition. Relevant to understanding lithium-sulfur battery chemistry, liquid sulfur is observed to form in the electrochemical cell and elucidates a long-debated reaction pathway for sulfur redox reaction in this environment.

36 MATERIALS SCIENCE↗

Spatio-temporal radiation biology with conventionally or laser-accelerated particles for ELIMED

The aim of this study is to investigate the behavior of radio-resistant human malignant cells, thus enabling better understanding of radiobiological effects of ions in such a case. Radiation sources such as accelerated continuous ion beams and laser technology-based ultra short radiation sources with energy of around 10 MeV will be used. The HTB140 melanoma cells are chosen since it has been shown that they represent the limit case of cellular radio-resistance among the studied tumor cell lines. These cells are particularly interesting as they provide data on the very edge of inactivation capacity of each beam line that is tested. After exposing the cell monolayers to continuous radiations of low (γ-rays) and high (protons) linear energy transfer, the kinetics of disappearance of the phosphorylated histone H2AX (γ-H2AX) foci per cell will be determined. The same procedure will be performed with the pulsed high dose rate protons. Detection and quantification of γ-H2AX foci will be performed by immunohistochemical 3D time-dependent imaging analyses using laser scanning confocal microscopy. Immunoblotting will enable the follow-up of the relation between γ-H2AX and cell cycle arrest via the p53/p21 pathway. In such a way the spatio-temporal changes on sub-cellular level will be visualized, quantified and compared. These results will show whether there is a difference in the effects on cells between continuous and pulsed irradiation mode. Therefore, they will contribute to the data base that might promote pulsed sources for medical treatments of malignant growths.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

The microstructure of dislocation clusters in industrial directionally solidified multicrystalline silicon

The microstructure of commonly occurring dislocation patterns in industrial directionally solidified multicrystalline silicon has been systematically studied by light microscopy, electron backscatter diffraction, and transmission electron microscopy. The work has been focused on dislocation clusters on wafers near the top of cast blocks. In near {l_brace}111{r_brace} grain surface, dislocation arrays parallel to {l_brace}110{r_brace} plane traces are lying in parallel rows of {l_brace}111{r_brace} planes inclined to the surface, in mainly <112>30 deg. orientation. The dislocation configuration suggests that the microstructure may result from a recovery process. The dislocations formed during crystal growth and cooling have undergone transformations at high temperature in order to achieve low energy configurations for minimization of dislocation and crystal energy.

36 MATERIALS SCIENCE↗

Photon up-conversion production in Tb{sup 3+}–Yb{sup 3+} co-doped CaF{sub 2} phosphors prepared by combustion synthesis

Graphical abstract: Up-conversion luminescence from Tb{sup 3+} obtained by energy transfer from Yb{sup 3+} pairs in CaF{sub 2} powder prepared by combustion synthesis. - Highlights: • Calcium fluoride (CaF{sub 2}) powders were prepared by combustion synthesis. • Rare-earth ions doped in this material were found in interstitial sites. • Cooperative up-conversion was observed in Tb{sup 3+}:Yb{sup 3+}:CaF{sub 2} powder. • Energy transfer between Tb{sup 3+} and pairs of Yb{sup 3+} was analyzed using rate equations. - Abstract: Calcium fluoride (CaF{sub 2}) crystalline powders were successfully prepared by the combustion synthesis method. The powder material containing luminescent rare-earth ions, more specifically terbium (Tb{sup 3+}) and ytterbium (Yb{sup 3+}), was studied by X-ray diffraction, scanning electronic microscopy and optical spectroscopy. These ions are allocated in charge compensated interstitial positions of tetragonal (C{sub 4v}) and trigonal (C{sub 3v}) symmetry sites of the cubic (O{sub h}) CaF{sub 2} lattice. Up-conversion (UC) luminescence in Tb{sup 3+} was achieved using a low power diode laser operating at 975 nm. Tb{sup 3+} is insensitive to near-infrared radiation but UC can be achieved via energy transfer from pairs of Yb{sup 3+} ions to Tb{sup 3+} ions. The UC luminescence dynamics of Tb{sup 3+} was used to study the energy transfer mechanism.

36 MATERIALS SCIENCE↗

A comparative study of electronic and structural properties of polycrystalline and epitaxial magnetron-sputtered ZnO:Al and Zn{sub 1-x}Mg{sub x}O:Al Films—Origin of the grain barrier traps

Homoepitaxial and heteroepitaxial ZnO, ZnO:Al, and Zn{sub 1-x}Mg{sub x}O:Al films have been grown by magnetron sputtering from ceramic targets at substrate temperatures between 200 °C and 500 °C. We studied the relation between the electronic transport and structural properties for the epitaxially grown films and compared it to the properties of polycrystalline films by means of X-ray diffraction, transmission electron microscopy and optical reflectance and transmittance measurements. The results show that the epitaxial growth of ZnO:Al and Zn{sub 1-x}Mg{sub x}O:Al thin films, which has been observed for nearly all films prepared on single crystalline substrates, will not significantly improve the electronic transport properties in comparison to polycrystalline films unless the grain boundaries are eliminated completely. The grain boundary defect densities of about 3 × 10{sup 13} cm{sup −2} are nearly independent on the structural quality of the different polycrystalline, hetero- and homoepitaxial films. This clearly proves that the grain boundary defects are not caused by crystallographic defects, but, most probably, by the dopant aluminium.

36 MATERIALS SCIENCE↗

Effect of secondary gas-phase reactions (SGR) in pyrolysis of carbon feedstocks for anisotropic carbon materials production – 1: Controlling SGR to modify intermediate coal tar species to improve pitch anisotropy

To meet the increasing demand for graphitizable carbon products, such as needle coke and carbon fiber, more carbon feedstocks capable of forming anisotropy should be utilized. Non-coking coals are widely available but are not typically suitable for producing anisotropic carbons due to lacking proper coal chemistry. This work used secondary gas-phase reactions (SGR) during coal pyrolysis to improve the coal tar chemistry of a non-coking coal for anisotropic carbon production. SGR pyrolysis temperatures and residence times were varied (T = 800–900°C and τ = 0–2.5 s), and analysis of the intermediate coal tar products showed that as these SGR pyrolysis conditions increased, the oxygen and aliphatic concentrations decreased, whereas aromatic contents and molecular weights increased. Without any SGR, microscopy of the thermally-treated coal tar pitch product revealed that the coal tar pitch was isotropic; however, upon using increased SGR pyrolysis conditions, the resulting coal tar pitch samples substantially increased in the percentage and quality of anisotropy formation. Further, the products' analyses show clear trends of modified chemical properties in the intermediate coal tar and improved anisotropy results. Thus, the results presented in this work show that by controlling the SGR during pyrolysis of a non-coking coal, this approach can modify the coal tar chemistry towards a precursor more suitable for quality anisotropic carbon material production.

01 COAL, LIGNITE, AND PEAT↗

Pulse Radiolysis Investigation of Radicals Derived from Water-Soluble Cyanine Dyes: Implications for Super-resolution Microscopy

Light-induced blinking, an inherent feature of many forms of super-resolution microscopy, has been linked to transient reduction of the fluorescent cyanine dye used as an imaging agent. There is, however, only scant literature information related to one-electron reduced cyanine dyes, especially in an aqueous environment. Here, we examine a small series of cyanine dyes, possessing disparate π-conjugation lengths, under selective reducing or oxidizing conditions. The experiment allows recording of both differential absorption spectra and decay kinetics of the resultant one-electron reduced or oxidized transient species in water. Relative to the ground state, absorption transitions for the various radicals are weak and somewhat broadened but do allow correlation with the π-conjugation length. In all cases, absorption maxima lie to the blue of the main ground-state transition. Under anaerobic conditions, the transient species decay on the microsecond to millisecond time scale, with the mean lifetime depending on molecular structure, radiation dose, and dye concentration. The experimental absorption spectra recorded for the one-electron reduced radicals and the presumed dimer cation radical compare well to spectra obtained from time-dependent density functional theory calculations. Furthermore, the results allow conclusions to be drawn regarding the plausibility of the reduced species being responsible for light-induced blinking in direct stochastic optical reconstruction microscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In Operando Visualization of the Electrochemical Formation of Liquid Polybromide Microdroplets

Zinc–bromine flow batteries are promising for stationary energy storage, and bromine-complexing agents have been used to form phase-separated liquid polybromide products. However, an understanding of the dynamics of polybromide nucleation is limited due to the beam sensitivity and complexity of polybromides. Here we report an in operando platform composed of dark-field light microscopy and a transparent electrochemical cell to reveal the dynamics of polybromide formation in their native environment. Using our platform, we confirm and reveal the liquid nature, chemical composition, pinning effect (strong interaction with Pt), residual effect (residual charge products on the surface), self-discharging, and over-oxidation of the polybromide products. Overall, the results provide insights into the role of complexing agents and guide the future design of zinc–bromine flow batteries. Furthermore, our in operando platform can potentially be used to study sensitive species and phases in other electrochemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Thermodenuding on the Structure of Nascent Flame Soot Aggregates

The optical properties (absorption and scattering) of soot particles depend on soot size and index of refraction, but also on the soot complex morphology and the internal mixing with materials that can condense on a freshly emitted (nascent) soot particle and coat it. This coating can affect the soot optical properties by refracting light, or by changing the soot aggregate structure. A common approach to studying the effect of coating on soot optical properties is to measure the absorption and scattering coefficients in ambient air, and then measure them again after removing the coating using a thermodenuder. In this approach, it is assumed that: (1) most of the coating material is removed; (2) charred organic coating does not add to the refractory carbon; (3) oxidation of soot is negligible; and, (4) the structure of the pre-existing soot core is left unaltered, despite the potential oxidation of the core at elevated temperatures. In this study, we investigated the validity of the last assumption, by studying the effect of thermodenuding on the morphology of nascent soot. To this end, we analyzed the morphological properties of laboratory generated nascent soot, before and after thermodenuding. Our investigation shows that there is only minor restructuring of nascent soot by thermodenuding

54 ENVIRONMENTAL SCIENCES↗

Optical properties of bimodally distributed InAs quantum dots grown on digital AlAs 0.56 Sb 0.44 matrix for use in intermediate band solar cells

For this work, high-quality InAs quantum dots (QDs) with nominal thicknesses of 5.0–8.0 monolayers were grown on a digital AlAs 0.56 Sb 0.44 matrix lattice-matched to the InP(001) substrate. All QDs showed bimodal size distribution, and their optical properties were investigated by photoluminescence (PL) and time-resolved PL measurements. Power dependent PL exhibited a linear relationship between the peak energy and the cube root of the excitation power for both the small QD family (SQDF) and the large QD family (LQDF), which is attributed to the type-II transition. The PL intensity, peak energy, and carrier lifetime of SQDF and LQDF showed very sensitive at high temperature. Above 125 K, the PL intensity ratio increased continuously between LQDF and SQDF, the peak energy shifted anomalously in SQDF, and the longer carrier radiative lifetime (≥3.0 ns at 77 K) reduced rapidly in SQDF and slowly in LQDF. These results are ascribed to thermally activated carrier escape from SQDF into the wetting layer, which then relaxed into LQDF with low-localized energy states.

14 SOLAR ENERGY↗

Dynamic X-ray diffraction sampling for protein crystal positioning

A sparse supervised learning approach for dynamic sampling (SLADS) is described for dose reduction in diffraction-based protein crystal positioning. Crystal centering is typically a prerequisite for macromolecular diffraction at synchrotron facilities, with X-ray diffraction mapping growing in popularity as a mechanism for localization. In X-ray raster scanning, diffraction is used to identify the crystal positions based on the detection of Bragg-like peaks in the scattering patterns; however, this additional X-ray exposure may result in detectable damage to the crystal prior to data collection. Dynamic sampling, in which preceding measurements inform the next most information-rich location to probe for image reconstruction, significantly reduced the X-ray dose experienced by protein crystals during positioning by diffraction raster scanning. The SLADS algorithm implemented herein is designed for single-pixel measurements and can select a new location to measure. In each step of SLADS, the algorithm selects the pixel, which, when measured, maximizes the expected reduction in distortion given previous measurements. Ground-truth diffraction data were obtained for a 5 µm-diameter beam and SLADS reconstructed the image sampling 31% of the total volume and only 9% of the interior of the crystal greatly reducing the X-ray dosage on the crystal. Furthermore, by using in situ two-photon-excited fluorescence microscopy measurements as a surrogate for diffraction imaging with a 1 µm-diameter beam, the SLADS algorithm enabled image reconstruction from a 7% sampling of the total volume and 12% sampling of the interior of the crystal. When implemented into the beamline at Argonne National Laboratory, without ground-truth images, an acceptable reconstruction was obtained with 3% of the image sampled and approximately 5% of the crystal. The incorporation of SLADS into X-ray diffraction acquisitions has the potential to significantly minimize the impact of X-ray exposure on the crystal by limiting the dose and area exposed for image reconstruction and crystal positioning using data collection hardware present in most macromolecular crystallography end-stations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗