Search NASA⌕ Search

SEARCH · Search NASA

Results for “Precursor analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Modeling and experimental validation of a W f /W-fabrication by chemical vapor deposition and infiltration

Tungsten (W) has a unique combination of excellent thermal properties, low sputter yield, low hydrogen retention, and acceptable activation. Therefore, W is presently the main candidate for the first wall material in future fusion devices. However, its intrinsic brittleness and its further embrittlement during operation bears the risk of a sudden and catastrophic component failure. As a countermeasure, tungsten fiber-reinforced tungsten (W f /W) with extrinsic toughening is being developed. A possible synthesis route is chemical vapor deposition (CVD) using heated W fabrics as substrate. The challenge is that the growing CVD-W can isolate domains from precursor access leading to strength-reducing pores. To deepen the process understanding and to optimize the CVD parameters, models were developed with COMSOL Multiphysics and validated experimentally. W deposition rate equations as function of the temperature and the partial pressures of the precursors H 2 and WF 6 were experimentally validated in previous work. In the present article, these equations are applied to obtain partial pressures within the CVD reactor. The results are taken as input for transient simulations in the microscale, in which W coatings, growing onto multiple adjacent W fibers, were simulated via mesh deformation and remeshing. The surface-to-surface contact of the W coatings and the corresponding potential pore formation were simulated by implementing sophisticated deposition rate stop conditions. Within the measuring uncertainties of ≃ ±1%, the models are validated successfully by experimental comparison regarding the deposition rate, pore structure, and relative densities ranging from 0.6 to 0.9.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical properties of Li[Li{sub 0.2}Mn{sub 0.54}Co{sub 0.13}Ni{sub 0.13}]O{sub 2} cathode thin film by RF sputtering for all-solid-state lithium battery

The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin films were prepared by radio frequency magnetron sputtering on Pt/Ti/SiO{sub 2}/Si substrate with target contained a 5% excess of lithium precursor. Thin films were deposited under various deposition conditions such as working pressure, gas ratio of Ar and O{sub 2}, and the temperature of in-situ annealing treatment. The thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The electrochemical property was estimated by a WBC3000 cycler with Li|Li[Li{sub 0.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} half-type cell at 1C charge/discharge rate. The (0 0 3) and (1 0 4) diffraction peaks which represent layered {alpha}-NaFeO{sub 2} type structure (space group R-3m) were observed. Optimal magnetron sputtering conditions were detected. The 500 Degree-Sign C annealed thin film after deposited at 10 m Torr in Ar:O{sub 2}=3:1 shows a high discharge capacity of around 62 {mu}Ah/cm{sup 2} {mu}m with a high cyclic retention. - Graphical abstract: The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} films is suitable for Lithium thin film battery. The film exhibits great discharge capacity (62 {mu}Ah/cm{sup 2} {mu}m) up to 200 cycles. Highlights: Black-Right-Pointing-Pointer High capacity thin films were deposited by RF magnetron sputtering. Black-Right-Pointing-Pointer Sputtering conditions were optimized by structural and electrochemical analysis. Black-Right-Pointing-Pointer Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin film shows a high capacity, 62 {mu}Ah/cm{sup 2} {mu}m. Black-Right-Pointing-Pointer The thin film shows an excellent cycling stability up to 200 cycles.

36 MATERIALS SCIENCE↗

Synthesis of high surface area ZnO powder by continuous precipitation

Graphical abstract: High surface area ZnO powders are synthesized by a low temperature continuous precipitation under ultrasonication. Urea is used as precipitating agent so that no contamination of ZnO powder emanating from precipitating agent, such as, alkalis, is observed. pH and type of precursor greatly affects the surface area and other properties. In this manuscript, we report a very simple and effective continuous precipitation to synthesize high surface area ZnO powder. Highlights: Black-Right-Pointing-Pointer The synthesis of high surface area ZnO powder was achieved at 90 Degree-Sign C in a continuous precipitation unit. Black-Right-Pointing-Pointer Continuous precipitation unit was ultrasonicated to improve final product homogeneity. Black-Right-Pointing-Pointer Precipitation intermediate, hydrozincite, was led to high surface area ZnO powder. Black-Right-Pointing-Pointer The synthesized ZnO nanoparticles had a rather uniform mesoporous structure. -- Abstract: Synthesis of high surface area ZnO powder was achieved by continuous precipitation using zinc ions and urea at low temperature of 90 Degree-Sign C. The powder precipitated resulted in high-purity single-phase ZnO powder when calcined at 280 Degree-Sign C for 3 h in air. The solution pH and the precipitation duration strongly affected the surface area of the calcined ZnO powder. Detailed structural characterizations demonstrated that the synthesized ZnO powder were single crystalline with wurtzite hexagonal phase. The powdered samples precipitated by homogeneous precipitation crystallized directly to hydrozincite without any intermediate phase formation. The phase structures, morphologies and properties of the final ZnO powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), dynamic light scattering particle size analysis (DLS), and nitrogen physisorption in order to determine the specific surface area (BET) and the pore size distribution (BJH).

36 MATERIALS SCIENCE↗

Induction of multiple pleiotropic drug resistance genes in yeast engineered to produce an increased level of anti-malarial drug precursor, artemisinic acid

Background: Due to the global occurrence of multi-drug-resistant malarial parasites (Plasmodium falciparum), the anti-malarial drug most effective against malaria is artemisinin, a natural product (sesquiterpene lactone endoperoxide) extracted from sweet wormwood (Artemisia annua). However, artemisinin is in short supply and unaffordable to most malaria patients. Artemisinin can be semi-synthesized from its precursor artemisinic acid, which can be synthesized from simple sugars using microorganisms genetically engineered with genes from A. annua. In order to develop an industrially competent yeast strain, detailed analyses of microbial physiology and development of gene expression strategies are required. Results: Three plant genes coding for amorphadiene synthase, amorphadiene oxidase (AMO or CYP71AV1), and cytochrome P450 reductase, which in concert divert carbon flux from farnesyl diphosphate to artemisinic acid, were expressed from a single plasmid. The artemisinic acid production in the engineered yeast reached 250 μg mL-1 in shake-flask cultures and 1 g L-1 in bioreactors with the use of Leu2d selection marker and appropriate medium formulation. When plasmid stability was measured, the yeast strain synthesizing amorphadiene alone maintained the plasmid in 84% of the cells, whereas the yeast strain synthesizing artemisinic acid showed poor plasmid stability. Inactivation of AMO by a point-mutation restored the high plasmid stability, indicating that the low plasmid stability is not caused by production of the AMO protein but by artemisinic acid synthesis or accumulation. Semi-quantitative reverse-transcriptase (RT)-PCR and quantitative real time-PCR consistently showed that pleiotropic drug resistance (PDR) genes, belonging to the family of ATP-Binding Cassette (ABC) transporter, were massively induced in the yeast strain producing artemisinic acid, relative to the yeast strain producing the hydrocarbon amorphadiene alone. Global transcriptional analysis by yeast microarray further demonstrated that the induction of drug-resistant genes such as ABC transporters and major facilitator superfamily (MSF) genes is the primary cellular stress-response; in addition, oxidative and osmotic stress responses were observed in the engineered yeast. Conclusion: The data presented here suggest that the engineered yeast producing artemisinic acid suffers oxidative and drugassociated stresses. The use of plant-derived transporters and optimizing AMO activity may improve the yield of artemisinic acid production in the engineered yeast.

59 BASIC BIOLOGICAL SCIENCES↗

Application of NEAMS Codes to Capture MSR Phenomena

This report documents work completed in FY21 under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program’s Molten Salt Reactor (MSR) Application Drivers activity at Argonne. The common focus was on identifying the modeling and simulation functional requirements for designing, licensing, and operating MSRs and applying those capabilities already developed in NEAMS tools to example problems of interest. The four main parts of this report each focuses on a specific area of simulation physics as it relates to MSR phenomena: fuel evolution, chemistry, computational fluid dynamics (CFD), and systems analysis. In terms of fuel evolution, which includes depletion, decay, on-line separations, and transmutation, the current state of computational capabilities for modeling this behavior in liquid-fueled molten salt reactor is discussed. Some of the functional requirements to accomplish the various applications of MSR fuel depletion modeling are highlighted, followed by a summary of recent approaches and code development activities. The chemistry functional requirements were discussed in the context of several applications of high importance for MSRs, such as corrosion, salt chemistry, and species transport. Each of these types of chemistry modeling have considerable impact on various aspects of reactor applications, including informing on reactor designs, improving operational efficiencies, analyzing safety and reactivity concerns, and estimating the mechanistic source term of the reactor. A brief overview is also provided on code development activities ongoing under NEAMS relevant to chemistry modeling of MSRs. In terms of CFD applications, the state-of-the-art spectral element code, Nek5000 was used to model the fluid dynamics within a full core of the Molten Salt Fast Reactor (MSFR) concept designed as part of the Euratom EVOL project. This concept was selected as the challenge problem because of its similar features to several U.S. industry concepts. The goal was to model some of the fast MSR design challenges, including potential large internal re-circulations, the need of accurate tracking of delayed neutron precursors (DNP), and the lack of relevant thermal-hydraulics models/correlations, etc. Therefore, a series of CFD models were created for the MSFR core cavity using a k – τ model two-equation model for the turbulence. These first full core results demonstrated that any potential recirculation zones could be properly identified with the current NEAMS CFD capabilities. The development of these models will also set the stage for future testing of Nek5000’s functionalities to model other MSR thermal-fluid phenomena. Lastly, the validation of SAM against experimental data from the Molten Salt Reactor Experiment, which started in FY19, continues with the inclusion of modeling the reactivity insertion tests. This involved using SAM and its point kinetics model for flowing fuel salt to recreate the time dependent power changes and response after positive reactivity insertions at the 1, 5, and 8 MWt power levels. Through these exercises, several code modifications were suggested to the SAM development team and accommodated to enable closer agreement with solid technical and physical justifications. These include adding a moderator reactivity feedback coefficient as an available input and modifying the solution approach for the point kinetics model. Additional SAM development suggestions for flowing fuel MSRs include adding the capability to allow the moderator power change proportionally with the reactor power and enabling specification of the power and DNP distributions separately.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Characterization of the state of nanoparticle aggregation in non-equilibrium plasma synthesis systems

Non-equilibrium plasmas offer a unique environment for nanoparticle synthesis. Particles are homogeneously nucleated and grow at near room temperature as a result of non-thermal decomposition of vapor precursors by electrons and other plasma-excited species. Despite their widespread use, several features regarding particle growth in these systems remain poorly understood. In particular, particle aggregation (the formation of non-spherical entities composed of primary particles) is assumed to be negligible because of unipolar particle charging and subsequent Coulombic repulsion, which would hinder collisional growth. Here, we apply ion mobility-mass spectrometry (IM-MS) to a non-thermal, atmospheric pressure DC microplasma to study the state of aggregation of as-synthesized nanoparticles. Under all examined synthesis conditions, we find the presence of highly branched, chain-like aggregates at the reactor outlet, with a primary particle radius below 10 nm that is relatively insensitive to synthesis conditions. The aggregates are polydisperse, with mean masses and mobility diameters increasing with both increasing precursor concentration and increasing flow residence time within the system. TEM structural characterization shows that the aggregates can be described by a quasifractal model, with a fractal dimensions in the 1.6–2.0 range. The mass-mobility relationship inferred from IM-MS and TEM agrees well with Langevin dynamics simulations where coulomb interactions are not considered. We suggest that particle aggregation occurs either in the plasma volume due to the scavenging of smaller neutral or positively charged particles by growing aggregates or outside the reactor where the plasma density is lower and electrons are not available to maintain high levels of unipolar charge. Furthermore, the methods applied here additionally demonstrate the potential of IM-MS and TEM structural characterization in analyzing gas-phase nanoparticle production processes.

42 ENGINEERING↗

A renewed search for short-lived 126 Sn in the early Solar System: Hydride generation MC-ICPMS for high sensitivity Te isotopic analysis

Although there is limited direct evidence for supernova input into the nascent Solar System many models suggest it formed by the gravitational collapse of a molecular cloud that was triggered by a nearby supernova. Existing lines of evidence mostly in the form of short lived radionuclidespresent in the early Solar System are potentially consistent with this hypothesis but still allow for alternative explanations. Since the natural production of Sn-126 is thought to occur only in supernovae and this isotope has a short half-life (Sn-126 -> Te-126 t(1/2) = 235 ky) the discovery of extant Sn-126 would provide unequivocal proof of supernova input to the early Solar System. Previous attempts to quantify the initial abundance of Sn-126 by examining Sn-Te systematics in early solids have been hampered by difficulties in precisely measuring Te isotope ratios in these materials. Thus here we describe a novel technique that uses hydride generation to dramatically increase the ionization efficiency of Te-an approximately 30-fold increase over previous work. This introduction system when coupled to a MC-ICPMS enables highprecision Te isotopic analyses on samples with < 10 ng of Te. We used this technique to analyze Te from a unique set of calcium-aluminum-rich inclusions (CAIs) that exhibit an exceptionally large range in Sn/Te ratios facilitating the search for the short-lived isotope Sn-126. This sample set shows no evidence of live Sn-126 implying at most minor input of supernova material during the time at which the CAIs formed. However based on the petrology of this sample set combined with the higher than expected concentrations of Sn and Te as well as the lack of nucleosynthetic anomalies in other isotopes of Te suggest that the bulk of the Sn and Te recovered from these particular refractory inclusions is not of primary origin and thus does not represent a primary signature of Sn-Te systematics of the protosolar nebula during condensation of CAIs or their precursors. Although no evidence of supernova input was found based on Sn-Te systematics in this sample set hydride generation represents a powerful tool that can now be used to further explore Te isotope systematics in less altered materials.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Climate change penalty and benefit on surface ozone: a global perspective based on CMIP6 earth system models

Abstract This work presents an analysis of the effect of climate change on surface ozone discussing the related penalties and benefits around the globe from the global modelling perspective based on simulations with five CMIP6 (Coupled Model Intercomparison Project Phase 6) Earth System Models. As part of AerChemMIP (Aerosol Chemistry Model Intercomparison Project) all models conducted simulation experiments considering future climate (ssp370SST) and present-day climate (ssp370pdSST) under the same future emissions trajectory (SSP3-7.0). A multi-model global average climate change benefit on surface ozone of −0.96 ± 0.07 ppbv °C −1 is calculated which is mainly linked to the dominating role of enhanced ozone destruction with higher water vapour abundances under a warmer climate. Over regions remote from pollution sources, there is a robust decline in mean surface ozone concentration on an annual basis as well as for boreal winter and summer varying spatially from −0.2 to −2 ppbv °C −1 , with strongest decline over tropical oceanic regions. The implication is that over regions remote from pollution sources (except over the Arctic) there is a consistent climate change benefit for baseline ozone due to global warming. However, ozone increases over regions close to anthropogenic pollution sources or close to enhanced natural biogenic volatile organic compounds emission sources with a rate ranging regionally from 0.2 to 2 ppbv C −1 , implying a regional surface ozone penalty due to global warming. Overall, the future climate change enhances the efficiency of precursor emissions to generate surface ozone in polluted regions and thus the magnitude of this effect depends on the regional emission changes considered in this study within the SSP3_7.0 scenario. The comparison of the climate change impact effect on surface ozone versus the combined effect of climate and emission changes indicates the dominant role of precursor emission changes in projecting surface ozone concentrations under future climate change scenarios.

Zanis, Prodromos↗

Revision of laser-induced damage threshold evaluation from damage probability data

In this study, the applicability of commonly used Damage Frequency Method (DFM) is addressed in the context of Laser-Induced Damage Threshold (LIDT) testing with pulsed lasers. A simplified computer model representing the statistical interaction between laser irradiation and randomly distributed damage precursors is applied for Monte Carlo experiments. The reproducibility of LIDT predicted from DFM is examined under both idealized and realistic laser irradiation conditions by performing numerical 1-on-1 tests. A widely accepted linear fitting resulted in systematic errors when estimating LIDT and its error bars. For the same purpose, a Bayesian approach was proposed. A novel concept of parametric regression based on varying kernel and maximum likelihood fitting technique is introduced and studied. Such approach exhibited clear advantages over conventional linear fitting and led to more reproducible LIDT evaluation. Furthermore, LIDT error bars are obtained as a natural outcome of parametric fitting which exhibit realistic values. The proposed technique has been validated on two conventionally polished fused silica samples (355 nm, 5.7 ns).

36 MATERIALS SCIENCE↗

Unimolecular and bimolecular formic acid decomposition routes on dispersed Cu nanoparticles

The elementary steps and site requirements in formic acid (HCOOH) dehydrogenation on Cu surfaces remain of keen interest because formate species act as intermediates or spectators in methanol synthesis and water–gas shift reactions. Steady-state and transient kinetic data, isotopic effects, infrared spectra during catalytic and stoichiometric reactions, and theoretical treatments based on density functional theory (DFT) provide evidence for bimolecular reactions, in which saturated bidentate formate (*HCOO*) adlayers, present at 0.25 ML (0.25 *HCOO* per surface Cu atom), react with undissociated species (HCOOH$^\square$) bound at interstices within formate adlayers ($^\square$) to form H-bonded bimolecular HCOOH$^\square$-*HCOO* adducts. The co-existence of vicinal HCOOH$^\square$ and *HCOO* moieties is evident from antisymmetric infrared bands for *HCOO* that become stronger as a result of their H-bonding that perturbs the induced dipole moment of *HCOO* upon vibration, consistent with DFT-derived vibrational frequencies and intensities for such perturbed species. The *HCOO* moiety in this complex undergoes C-H activation via a transition state that is preferentially stabilized through H-bonding with the vicinal HCOOH$^\square$ relative to its *HCOO* precursor. DFT-derived HCOOH dehydrogenation activation barriers and those determined from the evolution of CO 2 from pre-adsorbed *HCOO* species are about 10 kJ mol -1 smaller in the presence of gaseous HCOOH reactants (because of HCOOH$^\square$-*HCOO* interactions) than those for the unimolecular decomposition of bound *HCOO* species. Such bimolecular routes are consistent with measured effects of HCOOH, H 2 , and CO pressures and of H/D isotopic substitution on dehydrogenation turnover rates and represent the predominant channel for the formation of CO 2 and H 2 during catalytic HCOOH dehydrogenation on Cu nanoparticles. A saturated *HCOO* adlayer that retains binding interstices and the presence of HCOOH(g) enable a sequence of elementary steps unavailable for *HCOO* species, thus circumventing unassisted unimolecular routes that exhibit higher activation barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Green Synthesis of Aluminium Oxide Nanoparticles and its Applications in Mechanical and Thermal Stability of Hybrid Natural Composites

In the current scenario, biosynthesis has a major trend in the world due to its eco-friendly approach, effectiveness and low cost. In this experiment Aluminium Oxide nano powder was extracted from ‘Muntingia Calabura’ leaf with aluminium nitrate as precursor. An attempt has been made to develop the properties of sisal/coir, sisal/banana and banana/coir based hybrid composite with addition of aluminium oxide (Al{sub 2}O{sub 3}) nano powder. Compression moulding technique was adapted to fabricate the epoxy based natural fiber composites. Nano Al{sub 2}O{sub 3} powder was added in 0, 1, 2 and 3 wt%. The results demonstrate that addition of nano powder up to 3 weight (wt) percentage improvise the tensile, flexural and impact properties for all incorporated hybrid fibers. Residual wt% for sisal/coir, sisal/banana and banana/coir hybrid composites enhanced from 27.15 to 29.14, 26.07 to 31.33% and 23.76 to 27.50% by 3% nano substitution. Degradation temperature improved in different stages of hybrid combinations. Scanning electron microscope (SEM) images clearly showed the reduction of fiber breakage, matrix breakage and void gaps due to alumina nano powder addition.

36 MATERIALS SCIENCE↗

Effects of Inflow Spatiotemporal Discretization on Wake Meandering and Turbine Structural Response using FAST.Farm

FAST.Farm is a newly developed multiphysics, midfidelity engineering tool that can be used to predict turbine power and structural loads of wind turbines in a wind farm with minimal computational expense. Previous studies have shown similarities and differences in wind turbine performance between FAST.Farm and high-fidelity large-eddy simulations (LES) using both LES precursor-generated inflow and TurbSim-generated synthetic inflow. While conservative resolutions have been used to date, no formal spatial or temporal discretization study has been performed for the FAST.Farm model wind domains. This work aims to study the effects of varying the spatial and temporal discretization of the wind domains on wake meandering (low-resolution domain) and turbine structural response (high-resolution domains) and resulting wake and load calculations. The purpose of this study is to establish convergence criteria and recommendations for discretization values in terms of rotor diameter (D, expressed in meters) that will maximize computational efficiency. To ensure a percent error of ≤ 1% in standard deviation of wake center position relative to the finest included resolution, a low-resolution time step of 0.024D s, 0.016D s, and 0.0079D s and a low-resolution spatial discretization of 0.079D m, 0.16D m, and 0.24D m is recommended for 8 m/s, 12 m/s, and 18 m/s mean ambient wind speed at hub height, respectively. These guidelines are likely applicable to other implementations of the dynamic wake meandering model. To ensure a percent error of ≤ 1% in standard deviation of all considered structural response outputs, a high-resolution time step that captures the highest influential excitation and natural frequencies in the system and a high-resolution spatial discretization comparable to the maximum airfoil cord length is recommended. Lastly, these guidelines are likely applicable to any aeroelastic analysis.

17 WIND ENERGY↗

Molten salt flux synthesis and crystal structure of a new open-framework uranyl phosphate Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}: Spectroscopic characterization and cationic mobility studies

The reaction of triuranyl diphosphate tetrahydrate precursor (UO{sub 2}){sub 3}(PO{sub 4}){sub 2}(H{sub 2}O){sub 4} with a CsI flux at 750 °C yields a yellow single crystals of new compound Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}. The crystal structure (monoclinic, space group C2/c, a=13.6261 (13) Å, b=8.1081(8) Å, c=12.3983(12) Å, β=114.61(12)°, V=1245.41(20) Å{sup 3} with Z=4) has been solved using direct methods and Fourier difference techniques. A full-matrix least-squares refinement on the basis of F{sup 2} yielded R1=0.028 and wR2=0.071 for 79 parameters and 1352 independent reflections with I≥2σ(I) collected on a BRUKER AXS diffractometer with MoKα radiation and a charge-coupled device detector. The crystal structure is built by two independent uranium atoms in square bipyramidal coordination, connected by two opposite corners to form infinite chains {sup 1}{sub ∞}[UO{sub 5}] and by one phosphorus atom in a tetrahedral environment PO{sub 4}. The two last entities {sup 1}{sub ∞}[UO{sub 5}] and PO{sub 4} are linked by sharing corners to form a three-dimensional structure presenting different types of channels occupied by Cs{sup +} alkaline cations. Their mobility within the tunnels were studied between 280 and 800 °C and compared with other tunneled uranyl minerals. The infrared spectrum shows a good agreement with the values inferred from the single crystal structure analysis of uranyl phosphate compound. - Graphical abstract: Arrhenius plot of the electrical conductivity of tunneled compounds Cs{sub 3}U{sub 2}PO{sub 10} and CsU{sub 2}Nb{sub 2}O{sub 11.5}. Highlights: ► The reaction of (UO{sub 2}){sub 3}(PO{sub 4}){sub 2}(H{sub 2}O){sub 4} in excess of molten CsI leads to single-crystals of new tunneled compound Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2}. ► Ionic conductivity measurements and crystal structure analysis indicate a strong connection of the Cs{sup +} cations to the tunnels. ► A low symmetry in Cs{sub 3}(UO{sub 2}){sub 2}(PO{sub 4})O{sub 2} is the cause of IR activation and splitting of the bands in the IR spectrum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single-Walled Carbon Nanotubes with Confined Chalcogens as the Catalysts and Electrodes for Oxygen Reduction Reaction in Fuel Cells

The goal of this project is to synthesize and characterize a new non-metal electro-catalyst for oxygen reduction reaction (ORR) for fuel cell applications. The intended catalyst is a composite material composed of sulfur chains encapsulated in narrow diameter single-walled carbon nanotubes (S@SWNTs). S@SWNTs were successfully synthesized through sulfur vapor infusion method, and validated with Raman spectroscopy. However, the electrochemical analysis on the ORR catalytic activity of S@SWNTs indicated that it had low ORR catalytic activity. Our theoretical study based on density functional theory (DFT) revealed that the poor oxygen adsorption (low binding energy) on the surface of S@SWNTs was the bottleneck of the entire catalytic reaction. The focus of the project was subsequently pivoted to the development of a new non-noble metal ORR catalyst that could provide durability in acidic electrolyte. The hypothesis was to encapsulate small iron (Fe) clusters in SWNTs (Fe@SWNTs) can provide ORR electro-catalytic activity and long durability in acidic environment. DFT-based computational studies were carried out to explore the feasibility of the Fe@SWNTs catalyst. The theoretical study indicated that Fe@SWNTs indeed could catalyze the ORR with lower theoretical overpotential than platinum (Pt). However, its weaker bonding energy with oxygen was the bottleneck of the overall reaction. On the other hand, Fe clusters (composed of 7 Fe atoms) encapsulated in nitrogen-doped SWNTs (Fe 7 @N 4 WSNTs) showed proper oxygen adsorption by the Fe cluster and low theoretical overpotential of ORR. Comparing to the Fe single atom catalyst on N-doped SWNTs (Fe-N 4 SWNTs), which is one the best non-noble metal ORR catalysts reported in the literature, the Fe 7 @N 4 WSNTs showed lower overpotential and better resistance to acidic environment. Fe encapsulated N-doped SWNTs were synthesized with ferrocene as the Fe precursors through vapor infusion method, and experimental validate is underway. This study theoretically demonstrated the feasibility of a new type of non-noble metal electro-catalyst for ORR that could have high catalytic activity and long durability.

08 HYDROGEN↗

Life-Cycle Assessment Integration into Scalable Open-Source Numerical Models (LiAISON) for Analyzing Emerging Low-Carbon Technologies

Decarbonizing the industrial sector is a significant challenge in achieving a net-zero greenhouse gas (GHG) emissions economy by 2050 and the Paris Agreement, i.e., a global climate change mitigation target of achieving a maximum average temperature change potential of 1.5 degrees Celsius or less by 2100 with respect to pre-industrial levels. In the United States (US), the industrial sector accounts for 23% of total GHG emissions and is home to a number of hard-to-electrify activities. The chemicals subsector has the single largest subsector emissions profile after direct emissions from fossil fuel combustion and leakage from fossil fuel distribution systems. Within the chemicals subsector, many processes depend on hydrogen or ammonia precursors. Decarbonizing these two commodities would contribute significantly to decarbonizing the industrial sector as hydrogen could also be used for low carbon steel production (e.g., hydrogen-based direct reduction of iron) and other industrial applications. Emerging technologies require the application of prospective life cycle assessment (LCA), which can account for technology (foreground) scaling and process improvements via learning-by-doing, among others. In many cases, the future system context (background) in which the technologies are assumed to operate in is equally relevant. Background scenarios generated by integrated assessment models (IAM) can coherently incorporate potential future dynamics of the energy-climate-human-land system. Further, IAM scenarios are harmonized across socioeconomic and climate change mitigation pathways, which facilitates the comparability of prospective LCAs using different IAMs. We introduce an open source prospective LCA framework, the Life-cycle Assessment Integration into Scalable Open-source Numerical models (LiAISON), to analyze the non-linear relationships between technology foreground and the future energy system background across a series of midpoint and resource use metrics. The integration of LCA and IAM data is achieved using prospective environmental Impact assessment (PREMISE). We showcase it by assessing two Power-to-Hydrogen (PtH2) processes, namely Solid Oxide Electrolysis (SOE) and Polymer Electrolyte Membrane Electrolysis (PEME). We compare the technologies to a baseline of hydrogen production via natural gas-based Steam Methane Reforming (SMR) in a US context of multiple energy system and climate change mitigation futures. Besides providing an analysis that specifies the LCA results ranges with temporal and geospatial explicitness across the two technologies, metrics, and impact assessment methods, this research also aims to establish a base framework that can be expanded to use other IAM generated scenarios and US open-source life cycle inventory (LCI) databases. We find that the temporal environmental performance of either technology or their difference to SMR is directly influenced by the underlying background dynamics. Under baseline projections (i.e., no decarbonization goals), neither process reaches parity with the incumbent technology across several environmental metrics. Under the decarbonization scenarios, the underlying sectoral shifts result in declining impacts over time, compared to 2020 levels, except for metal depletion levels, which increase. The background shifts postulate a heavily decarbonized economy and energy system, which help technologies reach parity with SMR between 2040-2050 (RCP2.6) and 2030-2040 (RCP1.9) for global warming. Despite declines across several other metrics over time, neither PtH2 technology break even with SMR by 2100 besides for global warming.

decarbonizing↗

Life-Cycle Assessment Integration into Scalable Open-Source Numerical Models (LiAISON) for Analyzing Emerging Low-Carbon Technologies

Decarbonizing the industrial sector is a significant challenge in achieving a net-zero greenhouse gas (GHG) emissions economy by 2050 and the Paris Agreement, i.e., a global climate change mitigation target of achieving a maximum average temperature change potential of 1.5 degrees C or less by 2100 with respect to pre-industrial levels. In the United States (US), the industrial sector accounts for 23% of total GHG emissions and is home to a number of hard-to-electrify activities. The chemicals subsector has the single largest subsector emissions profile after direct emissions from fossil fuel combustion and leakage from fossil fuel distribution systems. Within the chemicals subsector, many processes depend on hydrogen or ammonia precursors. Decarbonizing these two commodities would contribute significantly to decarbonizing the industrial sector as hydrogen could also be used for low carbon steel production (e.g., hydrogen-based direct reduction of iron) and other industrial applications. Emerging technologies require the application of prospective life cycle assessment (LCA), which can account for technology (foreground) scaling and process improvements via learning-by-doing, among others. In many cases, the future system context (background) in which the technologies are assumed to operate in is equally relevant. Background scenarios generated by integrated assessment models (IAM) can coherently incorporate potential future dynamics of the energy-climate-human-land system. Further, IAM scenarios are harmonized across socioeconomic and climate change mitigation pathways, which facilitates the comparability of prospective LCAs using different IAMs. We introduce an open source prospective LCA framework, the Life-cycle Assessment Integration into Scalable Open-source Numerical models (LiAISON), to analyze the non-linear relationships between technology foreground and the future energy system background across a series of midpoint and resource use metrics The integration of LCA and IAM data is achieved using prospective environmental Impact assessment (PREMISE). We showcase it by assessing two Power-to-Hydrogen (PtH2) processes, namely Solid Oxide Electrolysis (SOE) and Polymer Electrolyte Membrane Electrolysis (PEME). We compare the technologies to a baseline of hydrogen production via natural gas-based Steam Methane Reforming (SMR) in a US context of multiple energy system and climate change mitigation futures. Besides providing an analysis that specifies the LCA results ranges with temporal and geospatial explicitness across the two technologies, metrics, and impact assessment methods, this research also aims to establish a base framework that can be expanded to use other IAM generated scenarios and US open-source life cycle inventory (LCI) databases. We find that the temporal environmental performance of either technology or their difference to SMR is directly influenced by the underlying background dynamics. Under baseline projections (i.e., no decarbonization goals), neither process reaches parity with the incumbent technology across several environmental metrics. Under the decarbonization scenarios, the underlying sectoral shifts result in declining impacts over time, compared to 2020 levels, except for metal depletion levels, which increase. The background shifts postulate a heavily decarbonized economy and energy system, which help technologies reach parity with SMR between 2040-2050 (RCP2.6) and 2030-2040 (RCP1.9) for global warming. Despite declines across several other metrics over time, neither PtH2 technology break even with SMR by 2100 besides for global warming.

decarbonizing↗

Towards Prospective LCA Using Life-Cycle Assessment Integration into Scalable Open-Source Numerical Models (LiAISON) Framework for Analyzing Emerging Low-Carbon Technologies

Decarbonizing the industrial sector is a significant challenge in achieving a net-zero greenhouse gas (GHG) emissions economy by 2050 and the Paris Agreement, i.e., a global climate change mitigation target of achieving a maximum average temperature change potential of 1.5 Degrees Celsius or less by 2100 with respect to pre-industrial levels. In the United States (US), the industrial sector accounts for 23% of total GHG emissions and is home to a number of hard-to-electrify activities. The chemicals subsector has the single largest subsector emissions profile after direct emissions from fossil fuel combustion and leakage from fossil fuel distribution systems. Within the chemicals subsector, many processes depend on hydrogen or ammonia precursors. Decarbonizing these two commodities would contribute significantly to decarbonizing the industrial sector as hydrogen could also be used for low carbon steel production (e.g., hydrogen-based direct reduction of iron) and other industrial applications. Emerging technologies require the application of prospective life cycle assessment (LCA), which can account for technology (foreground) scaling and process improvements via learning-by-doing, among others. In many cases, the future system context (background) in which the technologies are assumed to operate in is equally relevant. Background scenarios generated by integrated assessment models (IAM) can coherently incorporate potential future dynamics of the energy-climate-human-land system. Further, IAM scenarios are harmonized across socioeconomic and climate change mitigation pathways, which facilitates the comparability of prospective LCAs using different IAMs. We introduce an open source prospective LCA framework, the Life-cycle Assessment Integration into Scalable Open-source Numerical models (LiAISON), to analyze the non-linear relationships between technology foreground and the future energy system background across a series of midpoint and resource use metrics The integration of LCA and IAM data is achieved using prospective environmental Impact assessment (PREMISE). We showcase it by assessing two Power-to-Hydrogen (PtH2) processes, namely Solid Oxide Electrolysis (SOE) and Polymer Electrolyte Membrane Electrolysis (PEME). We compare the technologies to a baseline of hydrogen production via natural gas-based Steam Methane Reforming (SMR) in a US context of multiple energy system and climate change mitigation futures. Besides providing an analysis that specifies the LCA results ranges with temporal and geospatial explicitness across the two technologies, metrics, and impact assessment methods, this research also aims to establish a base framework that can be expanded to use other IAM generated scenarios and US open-source life cycle inventory (LCI) databases. We find that the temporal environmental performance of either technology or their difference to SMR is directly influenced by the underlying background dynamics. Additionally we compare our results by linking two other prospective models with LiAISON - GCAM(Global Change Assessment Model) and ReEDS (Regional Energy Deployment System) to analyze the effect of changing background scenarios using varying predictions in life cycle analysis.

emissions↗

Enhancing the multi-functional properties of renewable lignin carbon fibers via defining the structure–property relationship using different biomass feedstocks

Lignin has been explored extensively as a renewable precursor for carbon materials, considering its abundance as a major component of plant cell walls and its sustainability as a byproduct of both lignocellulosic biorefinery and the paper-making industry. Despite the extensive efforts to define the process–property relationship, it remains largely unknown how lignin biosynthesis and its chemistry would impact the resultant carbon fiber properties, for both mechanical and electroconductive performances. Such inadequate understanding fundamentally limits feedstock design and selection to improve carbon fiber properties toward broader commercial applications. Using lignin from a broad range of biomass feedstocks for carbon fiber manufacturing, we have fundamentally explored the structure–function relationship between lignin chemistry and carbon fiber performance. Specifically, lignin extracted from hardwood (sugar maple), softwood (loblolly pine and red cedar), and herbaceous plants (corn stover and switchgrass) was used for carbon fiber manufacturing, considering the very different lignin structures from these feedstocks. Linear regression models were established to define the relationship between carbon fiber mechanical properties and lignin structural characteristics. The results highlighted that the content of β-O-4 linkages correlates significantly with the tensile strength and elastic modulus of lignin carbon fibers, indicating that more linear β-O-4 linkages would promote the carbon fiber mechanical performance. Moreover, electroconductive properties are essential for broader energy device application of lignin-based carbon fibers, yet the mechanisms controlling their electroconductivity are largely unknown. Furthermore, we hereby demonstrated that a higher β-O-4 content also promotes the electroconductivity of lignin carbon fibers. Microstructure analysis further revealed that the crystallite size and content of the pre-graphitic turbostratic carbon structure in lignin-based carbon fibers were enhanced as the β-O-4 linkages increased. The content of β-O-4 linkages has shown a strong correlation with the crystallite content in a linear regression model. This study thus revealed the underlying mechanisms regarding how the lignin structure in planta defines the resultant carbon fiber properties. Moreover, the study also highlighted the correlation between the mechanical and electroconductive properties of lignin-based carbon fibers, both of which were defined by the lignin structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗