Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Structure and magnetic properties of bulk nanocrystalline Tm{sub 2}(Co{sub 1-x}Fe{sub x}){sub 17} permanent magnet

Structure and magnetic properties were studied for Tm{sub 2}(Co{sub 1-x}Fe{sub x}){sub 17} bulk nanocrystalline magnet synthesized by spark plasma sintering technique. X-ray diffraction results indicate both ingot and sintered magnet of Tm{sub 2}(Co{sub 0.7}Fe{sub 0.3}){sub 17} alloy exhibit hexagonal Th{sub 2}Ni{sub 17} type structure. The microstructure of the magnet is composed of Th{sub 2}Ni{sub 17} type nanograins with an average size of 35 nm detected by transmission electron microscopy and selected area electron diffraction patterns. Magnetic measurement shows that the remanence of the magnet is higher at 573 K than at 300 K, indicating there is a positive remanence temperature coefficient in the magnet. The anisotropy field of Tm{sub 2}(Co{sub 0.7}Fe{sub 0.3}){sub 17} alloy is 3.8 T, which is much higher than the H{sub A} of 2.3 T for the pure Tm{sub 2}Co{sub 17} alloy. The coercivity of the sintered magnet increases from 0.25 to 0.354 T after optimal annealing.

36 MATERIALS SCIENCE↗

Study of discharge after electron irradiation in sapphires and polycrystalline alumina

The fraction R of charges undergoing discharge during the time separating two electron pulses is derived from the induced current method developed in a scanning electron microscope. Irradiation is performed via a 10 keV defocused electron beam and low current density. The evolution of R with temperature (in the range 300-663 K) obeys to an Arrhenius type relation. Activation energies connected with the processes involved are deduced. In sapphire, no discernible discharge is observed due to the dominance of deep traps. In silver doped sapphire, R increases sharply from 10% to 70% as the temperature rises from 360 to 420 K, with a corresponding activation energy of 0.51 eV. In contrast, in polycrystalline alumina processed by solid state sintering (grain diameters of 1.7, 2.7, and 4.5 {mu}m) the degree of discharge increases continuously with temperature and grain size. The enhancement with grain size indicates that the sintering conditions influence strongly the efficiency of a gettering effect. The activation energy below 573 K is about 0.12 eV independently of grain size. Above 573 K, a second activation energy of 0.26 eV appears for the smallest grain size sample. The results suggest that discharge may stem from a density of trapping states, associated to grain boundaries in sintered samples, rather than from a single trapping level linked to the doping element as Ag in sapphire.

36 MATERIALS SCIENCE↗

Single phase synthesis and room temperature neutron diffraction studies on multiferroic PbFe{sub 0.5}Nb{sub 0.5}O{sub 3}

The lead-iron-niobate, (PbFe{sub 0.5}Nb{sub 0.5}O{sub 3} or PFN) was synthesized by low temperature sintering Single Step / Solid State Reaction Method. The 700 Degree-Sign C/2 hrs. calcined powder was sintered at 1050 Degree-Sign C/1 hr. The sintered pellets were characterized through X-Ray Diffraction and Neutron Diffraction at room temperature. It is found from the XRD pattern that the materials is in single phase with no traces of pyrochlore phase. It was also confirmed from the neutron diffraction pattern, the structure of PFN to be monoclinic, space group Cm. Structural studies has been carried out by refining the obtained neutron diffraction data by Rietveld refinement method using Fullprof program. The neutron diffraction pattern at 300 K (room temperature) was selected to refine the structure. The lattice parameters obtained are; a = 5.6709 A, b = 5.6732 A, c = 4.0136 A, and {alpha}= 90, {beta}= 89.881, {gamma}= 90. The P-E measurements showed hysteretic behavior with high remnant polarization.

36 MATERIALS SCIENCE↗

Structural and multiferroic properties of YMnO{sub 3} ceramics synthesized by co-precipitation method

Single phased hexagonal YMnO{sub 3} (YMO) ceramics have been synthesized via soft chemical co-precipitation route and adopting different sintering conditions. From the X-ray diffraction analysis, ceramic powder sintered at 600 Degree-Sign C was found to be amorphous. Sintering at 1000 Degree-Sign C lead to the formation of single phase YMO belonging to the noncentrosymmetric P6{sub 3}cm space group. Further, dielectric, Leakage and magnetic studies were performed at room temperature.

36 MATERIALS SCIENCE↗

Microstructural and crystallographic imperfections of MgB{sub 2} superconducting wire and their correlation with the critical current density

A comprehensive study of the effects of structural imperfections in MgB{sub 2} superconducting wire has been conducted. As the sintering temperature becomes lower, the structural imperfections of the MgB{sub 2} material are increased, as reflected by detailed X-ray refinement and the normal state resistivity. The crystalline imperfections, caused by lattice disorder, directly affect the impurity scattering between the π and σ bands of MgB{sub 2}, resulting in a larger upper critical field. In addition, low sintering temperature keeps the grain size small, which leads to a strong enhancement of pinning, and thereby, enhanced critical current density. Owing to both the impurity scattering and the grain boundary pinning, the critical current density, irreversibility field, and upper critical field are enhanced. Residual voids or porosities obviously remain in the MgB{sub 2}, however, even at low sintering temperature, and thus block current transport paths.

36 MATERIALS SCIENCE↗

Influence of La substitution on ferromagnetic properties of lead free Na{sub 0.5}Bi{sub 0.5}Ti{sub 0.988}Fe{sub 0.012}O{sub 3} multiferroic system

To study the effect of La doping and processing temperature, (Na{sub 0.5}Bi{sub 0.5}){sub 1−x}La{sub x}Ti{sub 0.988}Fe{sub 0.012}O{sub 3} (NBLTF) samples have been prepared by sol-gel method by employing two approaches namely with and without mol% excess of Na and Bi. X-ray diffraction analysis confirms the formation of rhombohedral perovskite structure in these samples with minor impurity phases. However, the impurity phases of stochiometric NBLTF samples disappear on increasing the sintering temperature from 650°C to 850°C. On other hand, NBLTF samples prepared with mol% excess of Na and Bi have shown pure perovskite structure only at lower sintering temperature 650°C and also at low concentration of La ∼ 1%. Transmission electron microscope investigation shows nano crystalline formation for all NBLTF samples sintered at 850°C. The enhancement in room temperature ferromagnetism is observed in La doped NBTF samples prepared at 850°C by taking stoichiometric amount of Na and Bi during synthesis.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Milling time and temperature dependence on Fe{sub 2}TiO{sub 5} nanoparticles synthesized by mechanical alloying method

Fe{sub 2}TiO{sub 5} is one type of titanate oxides which has M{sub x}Ti{sub y}O{sub z} crystal structure. It has various kinds of applications due to its electric and magnetic properties such as spintronics, electromagnetic devices, and gas sensor. In this study, Fe{sub 2}TiO{sub 5} nanoparticles were synthesized by simple mechanical alloying using planetary ball milling machine with various milling times and sintering temperatures. TiO{sub 2} and Fe{sub 2}O{sub 3} powders obtained from coprecipitation process were used as starting materials. The resulted Fe{sub 2}TiO{sub 5} powders were characterized by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Vibration Sample Magnetometer (VSM) in order to observe crystal quality, particles morphology, and magnetic properties respectively. As the milling time increases and the sintering temperature decreases, the crystal size of Fe{sub 2}TiO{sub 5} phase decreases. The smallest crystal size of the synthesized Fe{sub 2}TiO{sub 5} nanoparticles was ∼ 51 nm obtained by the milling time of 25 hours and sintering at 1100°C. The distribution of the resulted Fe{sub 2}TiO{sub 5} nanoparticles was not so homogeneous due to the appearance of small amount impurities. The VSM measurements show that a paramagnetic property was observed which should be analyzed more details on the low external magnetic fields.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of secondary phases on phase and microwave dielectric properties of new Ca{sub 2}Ce{sub 2}Ti{sub 5}O{sub 16} ceramics

Ca{sub 2}Ce{sub 2}Ti{sub 5}O{sub 16} ceramics processed via mix oxide route was investigated. Phase composition and microwave dielectric properties were measured using X-ray diffraction and a cavity method, respectively. CeO{sub 2} and another unidentified phase (that vanishes at ≥1400°C) existed as secondary phases along with the parent Ca{sub 2}Ce{sub 2}Ti{sub 5}O{sub 16} phase. The amount of the parent Ca{sub 2}Ce{sub 2}Ti{sub 5}O{sub 16} phase increased with increasing sintering temperature from 1350°C to 1450 °C accompanied by a decrease in the apparent density. The density decreased but ε{sub r} and Qufo increased with sintering temperature. An ε{sub r} ∼87.2, Qufo ∼5915 GHz and τ{sub f} ∼219 GHz was achieved for the sample sintered at 1450°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The influence of temperature induced phase transition on the energy storage density of anti-ferroelectric ceramics

Anti-ferroelectric (AFE) composite ceramics of (Pb{sub 0.858}Ba{sub 0.1}La{sub 0.02}Y{sub 0.008})(Zr{sub 0.65}Sn{sub 0.3}Ti{sub 0.05})O{sub 3}-(Pb{sub 0.97}La{sub 0.02})(Zr{sub 0.9}Sn{sub 0.05} Ti{sub 0.05})O{sub 3} (PBLYZST-PLZST) were fabricated by the conventional solid-state sintering process (CS), the glass-aided sintering (GAS), and the spark plasma sintering (SPS), respectively. The influence of the temperature induced phase transition on the phase structure, hysteresis loops, and energy storage properties of the composite ceramics were investigated in detail. The measured results of X-ray diffraction demonstrate that the composite ceramics exhibit the perovskite phases and small amounts of non-functional pyrochlore phases. Compared with the CS process, the GAS and SPS processes are proven more helpful to suppress the diffusion behaviors between the PBLYZST and PLZST phases according to the field emission scanning electron microscopy, thereby being able to improve the contribution of PBLYZST phase to the temperature stability of the orthogonal AFE phase. When the ambient temperature rises from 25 °C to 125 °C, CS and GAS samples have undergone a phase transition from orthorhombic AFE phase to tetragonal AFE phase, which results in a sharp decline in the energy storage density. However, the phase transition temperature of SPS samples is higher than 125 °C, and the energy storage density only slightly decreases due to the disorder of material microstructure caused by the high temperature. As a result, the SPS composite ceramics obtain a recoverable high energy storage density of 6.46 J/cm{sup 3} and the excellent temperature stability of the energy storage density of 1.16 × 10{sup −2} J/°C·cm{sup 3}, which is 1.29 × 10{sup −2} J/°C·cm{sup 3} lower than that of CS samples and about 0.43 times as that of GAS samples.

36 MATERIALS SCIENCE↗

Correlation of film morphology and defect content with the charge-carrier transport in thin-film transistors based on ZnO nanoparticles

The correlation of defect content and film morphology with the charge-carrier transport in field-effect devices based on zinc oxide nanoparticles was investigated. Changes in the defect content and the morphology were realized by annealing and sintering of the nanoparticle thin films. Temperature-dependent electrical measurements reveal that the carrier transport is thermally activated for both the unsintered and sintered thin films. Reduced energetic barrier heights between the particles have been determined after sintering. Additionally, the energetic barrier heights between the particles can be reduced by increasing the drain-to-source voltage and the gate-to-source voltage. The changes in the barrier height are discussed with respect to information obtained by scanning electron microscopy and photoluminescence measurements. It is found that a reduction of surface states and a lower roughness at the interface between the particle layer and the gate dielectric lead to lower barrier heights. Both surface termination and layer morphology at the interface affect the barrier height and thus are the main criteria for mobility improvement and device optimization.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of grain size on optical properties of iron oxide nanoparticles

In the present paper, iron oxide nanoparticles are successfully synthesized by the sol-gel method. The grain size is varied by sintering the nanoparticles at different temperature 400, 500, 600, 700 and 800 °C. Field emission scanning electron microscope (FESEM) image shows that the grains are uniformly distributed. The grain size increases from 15 nm to 35 nm with increasing the sintering temperature (400-800 °C). Energy dispersive X-ray spectroscopy (EDS) analysis shows that Fe is present in the stoichiometric ratio in all the synthesized samples. Fourier transform infrared spectroscopy (FTIR) spectra show that Fe-O stretching peaks appears at ∼495 cm{sup −1}. The value of energy band gap are found 2.75, 2.67, 2.62, 2.59, and 2.57 eV for the samples sintered at 400, 500, 600, 700 and 800 °C respectively. Therefore, the decrease in band gap with increasing the temperature has been observed. In this paper, the structural and optical properties have been explained on the basis of variation in the grain size with the temperature. The present studied samples more widely used in gas sensors and as catalysts.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural properties and gas sensing behavior of sol-gel grown nanostructured zinc oxide

In this communication, we report the results of the studies on structural properties and gas sensing behavior of nanostructured ZnO grown using acetone precursor based modified sol-gel technique. Final product of ZnO was sintered at different temperatures to vary the crystallite size while their structural properties have been studied using X-ray diffraction (XRD) measurement performed at room temperature. XRD results suggest the single phasic nature of all the samples and crystallite size increases from 11.53 to 20.96 nm with increase in sintering temperature. Gas sensing behavior has been studied for acetone gas which indicates that lower sintered samples are more capable to sense the acetone gas and related mechanism has been discussed in the light of crystallite size, crystal boundary density, defect mechanism and possible chemical reaction between gas traces and various oxygen species.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Bi doping on morphotropic phase boundary and dielectric properties of PZT

In our present attempt, Pb{sub (1-x)}Bi{sub x}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} [PBZT] {where x = 0, 0.05, 0.1} is synthesized by sol-gel route. Effect of Bi addition on structure, sinterability and dielectric properties are observed. The presence of morphotropic phase boundary (coexistence of tetragonal and rhombohedral symmetry) is confirmed by X-ray diffraction. Enhancement of sinterability after Bi doping is observed through a systematic sintering program. Frequency and temperature dependent dielectric constant are studied. Bi doping in PZT is found to enhance room temperature dielectric constant. However, at high temperature the dielectric constant of pure PZT is more than that of doped PZT.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Aerosol jet printed 3 omega sensors for thermal conductivity measurement

The 3 omega (3ω) method is a trusted technique for measuring thermal conductivity—a fundamental material property of critical importance in a broad range of applications. However, traditional 3ω sensor processing requires some form of physical vapor deposition, such as metal evaporation or sputtering. These 3ω sensor deposition techniques limit the materials and sample sizes applicable to the 3ω method. This work demonstrates an aerosol jet printing method to directly print silver 3ω sensors that yield accurate temperature-dependent measurement up to 300 °C on materials with thermal conductivity ranging from 1 to 150 W/m K. The interrelationship between printed sensor geometry, sensor thermal stability, and applicability to the 3ω method is examined. Thermal conductivity measurement with 3ω sensors conventionally sintered at 300 °C agrees to independent laser flash measurement within 4% from room temperature to 150 °C. An unconventional rapid high-temperature sintering method is shown to produce sensors that agree within 3% of the laser flash measurements from room temperature to 300 °C. The rapid sintering profiles also reduced the sensor–substrate thermal boundary resistance of the printed sensors by as much as 88%. The direct printing of 3ω sensors creates opportunities for measurement of thermal transport properties in applications previously inapplicable to the 3ω method.

47 OTHER INSTRUMENTATION↗

Fabrication of UN-Mo CERMET Nuclear Fuel Using Advanced Manufacturing Techniques

Ceramic-metallic nuclear fuels are a candidate fuel for nuclear thermal propulsion systems due to their high heat transport properties, which are necessary in very high-temperature environments. The conventional fabrication of uranium nitride–molybdenum fuel has been thoroughly studied in the past, but modern manufacturing techniques have presented a unique opportunity for further development within this field. This work demonstrates the use of advanced manufacturing techniques to produce nuclear fuel pellets composed of uranium nitride microspheres encased in a molybdenum matrix. Binder jetting is used to print molybdenum disks that are filled with uranium nitride microspheres and afterward sintered using spark plasma sintering. Two fuel pellets were fabricated to demonstrate the methodology and to provide a baseline analysis of the effects of temperature and pressure processing conditions. Characterization of the sintered fuel pellets includes detailed microstructural analysis and thermal conductivity measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ni-base superalloy powder-processed porous layer for gas cooling in extreme environments

Extreme high temperature conditions demand novel solutions for hot gas filters and coolant access architectures, i.e., porous layers on exposed components. These high temperatures, for example in current turbine engines, are at or exceeding current material limits for high temperature oxidation/corrosion, creep resistance, and, even, melting temperature. Thus novel blade designs allowing greater heat removal are required to maintain airfoil temperatures below melting and/ or rapid creep deformation limits. Gas atomized Ni-base superalloy powders were partially sintered into porous layers to allow full-surface, transpirational cooling of the surface of airfoils. Furthermore, these powder-processed porous layers were fully characterized for surface, morphology, cross-sectional microstructure, and mechanical strength characteristics. A sintering model based on pure Ni surface diffusion correlated well with the experimental results and allowed reasonable control over the partial sintering process to obtain a specified level of porosity within the porous layer.

36 MATERIALS SCIENCE↗

Low-Temperature Densification of Lanthanum Strontium Manganite (La1-xSrxMnO3+δ), x=0.0-0.20

Intermediate-stage sintering of lanthanum strontium manganite (LSM, where Sr=0.00, 0.05, 0.10, 0.15, and 0.20) was shown in dilatometry studies to be accelerated when subjected to alternating flows of air and nitrogen. The extent of rate enhancement decreased with increased Sr content, and decreases with increased temperature, which coincides with diminished oxygen non-stoichiometry. Shrinkage rates were shown further to be sensitive to the difference in oxygen content in the alternating gas flows. Baseline air sintering rates were measured using stepwise isothermal dilatometry, from which kinetic parameters were calculated using the Makipirtti-Meng model. Activation energies for sintering in air were determined to be 255±26, 258±28, 308±32, 373±37, and 417±41 kJ/mol for Sr=0.0, 0.05, 0.10, 0.15, and 0.20, respectively. A diffusion-based model is proposed that is consistent with trends in accelerated shrinkage versus temperature. Transient cation vacancy gradients, which lead to higher cation mobility, were calculated from established oxygen diffusivities and oxygen non-stoichiometry as a function of temperature and time. A potential application of this approach is processing of LSM-based cathode-side contact pastes in solid oxide fuel cells.

30 DIRECT ENERGY CONVERSION↗

The modification of BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} with copper oxide: Effect on the structural and transport properties

The effect of the content of CuO additive on the sinterability, phase composition, microstructure, and electrical properties of BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} proton-conducting material is studied. Ceramic samples were produced by the citrate–nitrate synthesis method with the addition of 0, 0.25, 0.5, and 1% CuO. It is shown that the relative density of the samples containing 0.5 and 1% CuO is higher than 94% at a sintering temperature of 1450°C, whereas the relative density of the material is no higher than 85% at a lower content of the sintering additive. From the data of X-ray diffraction analysis and scanning electron microscopy, it is established that the introduction of a small CuO content (0.25%) is inadequate for single-phase and high-dense ceramics to be formed. The conductivity and scanning electron microscopy data show that the sample with BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} + 0.5% CuO composition possesses high total and ionic conductivities as well as a high degree of microstructural stability after hydrogen reduction of the ceramics. The citrate–nitrate method modified by the introduction of a small CuO content can be recommended for the production of single-phase, gas-tight, and high-conductivity electrolytes based on both BaCeO{sub 3} and BaZrO{sub 3}.

36 MATERIALS SCIENCE↗