Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomically thin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,531 records · Page 85

Nanostructured and wide bandgap CdS:O thin films grown by reactive RF sputtering

In this study, CdS:O thin films were prepared from a 99.999% CdS target by reactive sputtering in a Ar:O{sub 2} (99:1) ambient with different RF power at room temperature. The deposited films were studied by means of XRD, SEM, EDX, Hall Effect and UV-Vis spectrometry. The incorporations of O{sub 2} into the films were observed to increase with the decrease of deposition power. The cryatallinity of the films were reduced, whereas the band gaps of the films were increased by the increase of O{sub 2} content on the films. The films were found in nano-structured grains with a compact surface. It has been seen that the highest carrier density is observed in the film with O{sub 2} at.% 21.10, while the values decreased with the further increase or decrease of O{sub 2} content on the films; indicating that specific amount of donor like O{sub 2} atoms substitute to the S atoms can improve the carrier density of the CdS:O thin film.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Evaluation of the electrical contact area in contact-mode scanning probe microscopy

The tunneling current through an atomic force microscopy (AFM) tip is used to evaluate the effective electrical contact area, which exists between tip and sample in contact-AFM electrical measurements. A simple procedure for the evaluation of the effective electrical contact area is described using conductive atomic force microscopy (C-AFM) in combination with a thin dielectric. We characterize the electrical contact area for coated metal and doped-diamond tips operated at low force (<200 nN) in contact mode. In both cases, we observe that only a small fraction (<10 nm{sup 2}) of the physical contact (∼100 nm{sup 2}) is effectively contributing to the transport phenomena. Assuming this reduced area is confined to the central area of the physical contact, these results explain the sub-10 nm electrical resolution observed in C-AFM measurements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ultra low-K shrinkage behavior when under electron beam in a scanning electron microscope

In this paper, we investigate the tendency of porous low-K dielectrics (also named Ultra Low-K, ULK) behavior to shrink when exposed to the electron beam of a scanning electron microscope. Various experimental electron beam conditions have been used for irradiating ULK thin films, and the resulting shrinkage has been measured through use of an atomic force microscope tool. We report the shrinkage to be a fast, cumulative, and dose dependent effect. Correlation of the shrinkage with incident electron beam energy loss has also been evidenced. The chemical modification of the ULK films within the interaction volume has been demonstrated, with a densification of the layer and a loss of carbon and hydrogen elements being observed.

36 MATERIALS SCIENCE↗

Influence of substrate temperature on structural and optical properties of RF sputtered ZnMnO thin films

The ZnMnO thin films were deposited on glass substrates by radio frequency magnetron sputtering method. The properties of ZnMnO thin films were investigated by high-resolution x-ray diffractometer (HRXRD),atomic force microscopy (AFM), UV-Vis spectrometer and room temperature photoluminescence (PL), under the influence of substrate temperature. The substrate temperature was varied from 300, 400 and 500°C. With increasing the substrate temperature, the structure of the films changed from cubic to hexagonal. The cubic ZnMnO thin films grown along [210] direction, while the hexagonal ones grown along [002] direction. The changes in surface morphology provided a proof on the structural transition. Also, decrease and increase of optical band gap is associated with cubic or hexagonal structure of the films.

36 MATERIALS SCIENCE↗

Particle atomic layer deposition of alumina for sintering yttria-stabilized cubic zirconia

The addition of aluminum oxide (Al 2 O 3 ) as a sintering aid to yttria-stabilized zirconia (YSZ) reduces the required densification temperature. Sintering aids are incorporated using a number of processes which can lead to ambiguity when determining the effect of the sintering aid on the densification mechanism. In this study, a novel method for sintering aid addition, Particle Atomic Layer Deposition (ALD), was used to deposit an amorphous Al 2 O 3 thin film on YSZ particles. Transmission electron microscopy confirmed the deposition of conformal Al 2 O 3 thin films on the surface of the YSZ particles. The addition of Al 2 O 3 to YSZ reduced the temperature at which densification began by ~75 degrees C, and 2.2 wt% Al 2 O 3 addition resulted in a minimum activation energy for the intermediate stage of densification. This concentration is well in excess of the solubility limit of Al 2 O 3 in YSZ, showing that Al 2 O 3 does not enhance the densification of YSZ solely by dissolving into the YSZ lattice and activating volume diffusion. The addition of 0.7 wt% Al 2 O 3 with one Particle ALD cycle enhanced the ionic conductivity of YSZ by 23% after sintering at 1350 degrees C for 2 hours, demonstrating that dense parts with high oxygen ion conductivities can be produced after sintering at reduced temperatures. One Particle ALD cycle is a fast, easily scaled-up process that eliminates the use of solvents and has substantial cost/performance advantages over conventional processing.

36 MATERIALS SCIENCE↗

Spatial Atomic Layer Deposition of Aluminum Oxide as a Passivating Hole Contact for Silicon Solar Cells

In this work, tunneling aluminum oxide (Al 2 O 3 ) passivation layers are demonstrated to be a candidate for hole collecting, passivating contacts when coupled with a boron-doped surface. Here, these very thin Al 2 O 3 films (1.5-3 nm) are deposited using spatial atomic layer deposition (ALD) on boron diffused (110-115 Ω –1 ) hydrophilic surfaces operating as metal-insulator-semiconductor (MIS) contacts. Emitter saturation current density values of approximately ≈57 fA cm 2 are achieved for Al 2 O 3 film thicknesses of 2 nm before metallization. At this same thickness, contact resistivity values of 33 mΩ cm 2 are obtained after metallization. Most importantly, the boron diffusion, wet chemical surface preparation, and spatial ALD of Al 2 O 3 used to create these MIS structures were all performed with industrially relevant equipment on Cz wafers.

14 SOLAR ENERGY↗

Finite-size effect on two-particle production in continuous and discrete spectrum

The formalism allowing one to account for the effect of a finite space-time extent of particle production region is given. Its applications to the lifetime measurement of hadronic atoms produced by a high-energy beam in a thin target, as well as to the femtoscopy techniques widely used to measure space-time characteristics of the production processes, are discussed. Particularly, it is found that the neglect of the finite-size effect on the pionium lifetime measurement in the experiment DIRAC at CERN could lead to the lifetime overestimation comparable with the 10% statistical error. The theoretical systematic errors arising in the calculation of the finite-size effect due to the neglect of non-equal emission times in the pair center-of-mass system, the space-time coherence and the residual charge are shown to be negligible.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Organic-Inorganic Reaction of Li-Containing thin film: Structure of Lithium Propane Dioxide via MLD

In combining organometallic with organic precursors, molecular layer deposition (MLD) offers not only an expanded portfolio of molecular combinations but specifically the possibility of tuning mechanical properties for more robust functionality. This is appealing for applications in energy storage, where ion transport in and out of electrodes causes significant stress/strain cycling. It is particularly opportune for Li-ion solid state batteries (LISSBs), where electrode and solid electrolyte structures are usually arranged densely for high power and energy. Despite diverse MLD applications to date, little prior research has been aimed at Li-containing MLD materials and processes. Here, we report the MLD growth and process for a lithium-containing organic thin film using lithium tert-butoxide (LiO t Bu) and 1,3-propanediol, leading to an MLD film of lithium propane dioxide, Li 2 O 2 C 3 H 6 (LPDO), identified through X-ray photoelectron spectroscopy (XPS) and ab initio calculations. The growth showed self-limiting behavior for both precursors, with significant nucleation delay before linear growth at 0.23 Å/cycle at 150 °C, and 0.15 Å/cycle at 200 °C. XPS-determined stoichiometry was Li 1.6 O 2.2 C 3 H 6 at both 150 and 200 °C, while additional species, presumably from incomplete reaction, were found at 100 °C, leading to a notably higher (0.84 Å/cycle) growth rate. The LPDO film showed crystallinity and high surface roughness when grown on the crystalline substrate, while on the amorphous substrate, an amorphous LPDO film with low surface roughness was observed. In addition, high air sensitivity of LPDO film was observed, with Li propyl carbonate and Li carbonate formation under air exposure. Further modification strategies were proposed in order to achieve a MLD or atomic layer deposition-/MLD-based solid electrolyte material.

25 ENERGY STORAGE↗

Atomic layer etching (ALE) of III-nitrides

Atomic layer etching (ALE) was performed on (Al, In, Ga)N thin films using a cyclic process of alternating Cl 2 gas absorption and Ar + ion bombardment in an inductively coupled plasma etcher system. The etch damage was characterized by comparing photoluminescence of blue single quantum well light-emitting diodes before and after the etch as well as bulk resistivities of etched p-doped layers. It was found that etched surfaces were smooth and highly conformal, retaining the step-terrace features of the as-grown surface, thus realizing ALE. Longer exposures to the dry etching increased the bulk resistivity of etched surfaces layers slightly, with a damaged depth of ∼55 nm. With further optimization and damage recovery, ALE is a promising candidate for controlled etching with atomic accuracy. Finally, it was found that Al 0.1 Ga 0.9 N acts as an etch barrier for the ALE etch, making it a suitable etch to reveal buried V-defects in III-nitride light emitting diodes.

Atomic-layer etching↗

Emerging edge states on the surface of the epitaxial semimetal CuMnAs thin film

Epitaxial thin films of CuMnAs have recently attracted attention due to their potential to host relativistic antiferromagnetic spintronics and exotic topological physics. Here, we report on the structural and electronic properties of a tetragonal CuMnAs thin film studied using scanning tunneling microscopy (STM) and density functional theory (DFT). STM reveals a surface terminated by As atoms, with the expected semi-metallic behavior. An unexpected zigzag step edge surface reconstruction is observed with emerging electronic states below the Fermi energy. DFT calculations indicate that the step edge reconstruction can be attributed to an As deficiency that results in changes in the density of states of the remaining As atoms at the step edge. Furthermore, this understanding of the surface structure and step edges on the CuMnAs thin film will enable in-depth studies of its topological properties and magnetism.

36 MATERIALS SCIENCE↗

Atom lithography with near-resonant standing waves

We study the optimal focusing of two-level atoms with a near-resonant standing wave light, using both classical and quantum treatments of the problem in the thin- and thick-lens regimes. It is found that the near-resonant standing wave focuses the atoms with a reduced background in comparison with far-detuned light fields. For some parameters, the quantum atomic distribution shows even better localization than the classical one. Spontaneous emission effects are included via the technique of quantum Monte Carlo wave function simulations. We investigate the extent to which nonadiabatic and spontaneous emission effects limit the achievable minimal size of the deposited structures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Plasma-enhanced atomic layer deposition and etching of high-k gadolinium oxide

Atomic layer deposition (ALD) of high-quality gadolinium oxide thin films is achieved using Gd(iPrCp){sub 3} and O{sub 2} plasma. Gd{sub 2}O{sub 3} growth is observed from 150 to 350 deg. C, though the optical properties of the film improve at higher temperature. True layer-by-layer ALD growth of Gd{sub 2}O{sub 3} occurred in a relatively narrow window of temperature and precursor dose. A saturated growth rate of 1.4 A/cycle was observed at 250 deg. C. As the temperature increases, high-quality films are deposited, but the growth mechanism appears to become CVD-like, indicating the onset of precursor decomposition. At 250 deg. C, the refractive index of the film is stable at {approx}1.80 regardless of other deposition conditions, and the measured dispersion characteristics are comparable to those of bulk Gd{sub 2}O{sub 3}. XPS data show that the O/Gd ratio is oxygen deficient at 1.3, and that it is also very hygroscopic. The plasma etching rate of the ALD Gd{sub 2}O{sub 3} film in a high-density helicon reactor is very low. Little difference is observed in etching rate between Cl{sub 2} and pure Ar plasmas, suggesting that physical sputtering dominates the etching. A threshold bias power exists below which etching does not occur; thus it may be possible to etch a metal gate material and stop easily on the Gd{sub 2}O{sub 3} gate dielectric. The Gd{sub 2}O{sub 3} film has a dielectric constant of about 16, exhibits low C-V hysteresis, and allows a 50 x reduction in gate leakage compared to SiO{sub 2}. However, the plasma enhanced atomic layer deposition (PE-ALD) process causes formation of an {approx}1.8 nm SiO{sub 2} interfacial layer, and generates a fixed charge of -1.21 x 10{sup 12} cm{sup -2}, both of which may limit use of PE-ALD Gd{sub 2}O{sub 3} as a gate dielectric.

36 MATERIALS SCIENCE↗

Emergent layer stacking arrangements in c-axis confined MoTe 2

The layer stacking order in 2D materials strongly affects functional properties and holds promise for next-generation electronic devices. In bulk, octahedral MoTe 2 possesses two stacking arrangements, the ferroelectric Weyl semimetal T d phase and the higher-order topological insulator 1T' phase. However, in thin flakes of MoTe 2 , it is unclear if the layer stacking follows the T d , 1T', or an alternative stacking sequence. Here, we use atomic-resolution scanning transmission electron microscopy to directly visualize the MoTe 2 layer stacking. In thin flakes, we observe highly disordered stacking, with nanoscale 1T' and T d domains, as well as alternative stacking arrangements not found in the bulk. We attribute these findings to intrinsic confinement effects on the MoTe 2 stacking-dependent free energy. Our results are important for the understanding of exotic physics displayed in MoTe 2 flakes. More broadly, this work suggests c-axis confinement as a method to influence layer stacking in other 2D materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High spin polarization in epitaxial Fe 4 N thin films using Cr and Ag as buffer layers

Fe 4 N thin films with (001) texture were prepared by reactive sputtering on MgO substrates, utilizing either a Cr or Ag buffer layer to facilitate the epitaxial growth. X-ray diffraction, atomic force microscopy, and vibrating sample magnetometry measurements show that the Fe 4 N thin film grown on the Ag buffer layer is superior to that grown on the Cr buffer layer. The point contact Andreev reflection measurement was then conducted, and the spin polarizations were determined to be 61.1% and 81.3% for Fe 4 N thin films with Cr and Ag buffer layers, respectively. The 81.3% spin polarization is significantly higher than the ratio reported previously for Fe 4 N and is comparable with that of state-of-the-art Heusler alloys. This result is in agreement with the theoretical prediction on the discrepancy between the two differently defined spin polarizations for Fe 4 N. Moreover, our study indicates that an optimized growth process for Fe 4 N thin films is crucial for achieving a high spin polarization and that true half-metallicity could potentially be realized with Fe 4 N. Furthermore the high spin polarization of Fe 4 N combined with its low fabrication temperature and simple composition makes Fe 4 N a competitive candidate to be a half-metallic ferromagnet in spintronic devices.

36 MATERIALS SCIENCE↗

Emission Kinetics of Surface (Bi)Excitons in ZnO Thin Films

The kinetics of near-edge photoluminescence (PL) in ZnO nanofilms prepared by the atomic layer deposition has been investigated. It is established that the kinetics of near-edge PL in 4-nm films is determined to a great extent by surface 2D-exciton (SX) and biexciton (SXX) complexes. The contribution from surface biexcitons is estimated based on a photostimulated change in the surface potential in ZnO films with different thicknesses. Ultrafast dynamics of surface biexcitons in thin films are revealed. It is shown that biexcitons localized near the surface have the shortest radiative lifetime (less than 100 ps) among all bound exciton complexes, which is explained by the large oscillator strength.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Layer-by-layer deposition of ultra-thin hybrid/microporous membrane for CO 2 separation

Based on two issued US patent, US7947579B2 and US8187678B2 that were invented by our team member at the University of New Mexico and Sandia National Labs, using atomic layer deposition technique (ALD) and molecular self-assembly or templating technique, An ultra-thin CO 2 membrane with CO 2 permeance up to 1580 GPU and CO 2 /N 2 up to 62 has been achieved in phase I project, promising for cost-effective CO 2 separations. As the first step of the project, a robust membrane fabrication protocol was established. To address the defects in the membrane structure, ALD treatment on AO support, multiple dip-coating processes and slow calcination steps were adopted. Consequently, defects were no longer evident in the nanoporous support, which ensures a reliable procedure for lab-scale membrane fabrications as well as the high-fidelity experimental findings. The same procedures may also be helpful for future scaling-up protocols. The layer-by-layer membrane fabrication was started by using a bridged disilane BTEE as the ALD precursor, wherein the organic groups at the bridging site were expected to be aligned layer-by-layer to form Angstrom-channels for CO 2 transport. Using 2-level factorial experimental design, we have found that ALD reaction time and ALD temperature were important factors impacting the CO 2 permeance and selectivity. Longer reaction time and higher ALD temperature were found to be advantageous for better CO 2 permeance and selectivity, which is in agreement with our model that better-aligned CO 2 -channels formed by the layer-by-layer stacking of the organic ligands can be achieved by a slower “stacking” process (longer reaction time) and stronger self-alignment tendency (higher ALD temperature). This observation will be an important guidance for our future membrane designs. The CO 2 -channel templated by –(CH 2 ) 2 - in BTEE was found to be too tight to facilitate fast CO 2 transport, but larger channel diameter is in contradiction with higher CO 2 selectivity. Therefore, the size-exclusion mechanism by itself is not sufficient for effective CO 2 separation. For this reason, the chemistry of the CO 2 -channel has to be carefully tuned. An amine bridged-disilane BTMA was therefore used as ALD precursor for larger CO 2 channel and high CO 2 -affinity chemistry. For BMTA membrane with amine chemistry measured at 100C, the CO 2 permeance was 1030 GPU for 100-cycle-ALD sample with CO 2 /N 2 selectivity of 17, and 302 GPU for 200-cycle-ALD sample with CO 2 /N 2 selectivity of 44. The increase of CO 2 permeance and the CO 2 /N 2 selectivity at elevated temperature is an evidence showing that there is a preferential chemical interaction between CO 2 and –NH functional groups in the membrane, which facilitates selective transport of CO 2 through the membrane. Therefore, using larger organic ligands as the CO 2 -channel template and the introduction of –NH chemistry to the membrane structure were proved to be an effective strategy in achieving better CO 2 permeance and selectivity. Guided by the same strategy, BTMA membrane was irradiated with UV to remove the bridging ligands for larger CO-channel, followed by Zn 2+ and Ni 2+ chemistry modification. Results showed that Zn 2+ or Ni 2+ chemistries will both enhance the selective CO 2 transport thereby the CO 2 /N 2 selectivity, and increasing separation temperature will further improve the CO2 permeance and selectivity. For BTMA membrane with Ni 2+ chemistry measured at 100C, CO 2 permeance of 1580 GPU and CO 2 /N 2 of 62 were achieved, promising for scaled-up industrial applications. Further, same membrane was tested at simulated flue gas condition (with SO 2 at 60C), the CO 2 permeance was 920 GPU and the CO 2 /N 2 selectivity was 52, suggesting the membrane still worked well under simulated flue gas conditions, primarily due to the stable ceramic framework of this membrane.

36 MATERIALS SCIENCE↗

Ultra Slow Muon Project at J-PARC, MUSE

The muon science facility (MUSE), along with the neutron, hadron, and neutrino facilities, is one of the experimental areas of the J-PARC project, which was approved for construction at the Tokai JAEA site. The MUSE facility is located in the Materials and Life Science Facility (MLF), which is a building integrated to include both neutron and muon science programs. Construction of the MLF building was started in the beginning of 2004, and first muon beam is expected in the autumn of 2008.As a next step, we are planning to install, a Super Omega muon channel with a large acceptance of 400 msr, to extract the world strongest pulsed surface muon beam. Its goal is to extract 4x10{sup 8} surface muons/s for the generation of the intense ultra slow muons, utilizing laser resonant ionization of Mu by applying an intense pulsed VUV laser system. As maximum 1x10{sup 6} ultra slow muons/s will be expected, which will allow for the extension of {mu}SR into the field of thin film and surface science.

74 ATOMIC AND MOLECULAR PHYSICS↗

Obtaining a Low and Wide Atomic Layer Deposition Window (150-275 °C) for In 2 O 3 Films Using an In III Amidinate and H 2 O

Indium oxide is a major component of many technologically important thin films, most notably the transparent conductor indium tin oxide (ITO). Despite being pyrophoric, homoleptic indium(III) alkyls do not allow atomic layer deposition (ALD) of In 2 O 3 using water as a co-precursor at substrate temperatures below 200 °C. Several alternative indium sources have been developed, but none allows ALD at lower temperatures except in the presence of oxidants such as O 2 or O 3 , which are not compatible with some substrates or alloying processes. We have synthesized a new indium precursor, tris( N , N' -diisopropylformamidinato)indium(III), compound 1 , which allows ALD of pure, carbon-free In 2 O 3 films using H 2 O as the only co-reactant, on substrates in the temperature range 150–275 °C. In contrast, replacing just the H of the anionic i PrNC(H)N i Pr ligand with a methyl group (affording the known tris( N , N' -diisopropylacetamidinato)indium(III), compound 2 ) results in a considerably higher and narrower ALD window in the analogous reaction with H 2 O (225–300 °C). Kinetic studies demonstrate that a higher rate of surface reactions in both parts of the ALD cycle gives rise to this difference in the ALD windows.

charge transport↗